/
dac_common.h
98 lines (86 loc) · 2.55 KB
/
dac_common.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
// Copyright 2015-2016 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#pragma once
#ifdef __cplusplus
extern "C" {
#endif
#include <stdint.h>
#include "esp_err.h"
#include "driver/gpio.h"
#include "hal/dac_types.h"
/**
* @brief Get the GPIO number of a specific DAC channel.
*
* @param channel Channel to get the gpio number
* @param gpio_num output buffer to hold the gpio number
* @return
* - ESP_OK if success
*/
esp_err_t dac_pad_get_io_num(dac_channel_t channel, gpio_num_t *gpio_num);
/**
* @brief Set DAC output voltage.
* DAC output is 8-bit. Maximum (255) corresponds to VDD3P3_RTC.
*
* @note Need to configure DAC pad before calling this function.
* DAC channel 1 is attached to GPIO25, DAC channel 2 is attached to GPIO26
* @param channel DAC channel
* @param dac_value DAC output value
*
* @return
* - ESP_OK success
*/
esp_err_t dac_output_voltage(dac_channel_t channel, uint8_t dac_value);
/**
* @brief DAC pad output enable
*
* @param channel DAC channel
* @note DAC channel 1 is attached to GPIO25, DAC channel 2 is attached to GPIO26
* I2S left channel will be mapped to DAC channel 2
* I2S right channel will be mapped to DAC channel 1
*/
esp_err_t dac_output_enable(dac_channel_t channel);
/**
* @brief DAC pad output disable
*
* @param channel DAC channel
* @note DAC channel 1 is attached to GPIO25, DAC channel 2 is attached to GPIO26
* @return
* - ESP_OK success
*/
esp_err_t dac_output_disable(dac_channel_t channel);
/**
* @brief Enable cosine wave generator output.
*
* @return
* - ESP_OK success
*/
esp_err_t dac_cw_generator_enable(void);
/**
* @brief Disable cosine wave generator output.
*
* @return
* - ESP_OK success
*/
esp_err_t dac_cw_generator_disable(void);
/**
* @brief Config the cosine wave generator function in DAC module.
*
* @param cw Configuration.
* @return
* - ESP_OK success
* - ESP_ERR_INVALID_ARG The parameter is NULL.
*/
esp_err_t dac_cw_generator_config(dac_cw_config_t *cw);
#ifdef __cplusplus
}
#endif