rtc.h

/*
 * SPDX-FileCopyrightText: 2020-2021 Espressif Systems (Shanghai) CO LTD
 *
 * SPDX-License-Identifier: Apache-2.0
 */
#pragma once

#include <stdbool.h>
#include <stddef.h>
#include <stdint.h>
#include "soc/soc.h"
#include "soc/clk_tree_defs.h"

#ifdef __cplusplus
extern "C" {
#endif

/**
 * @file rtc.h
 * @brief Low-level RTC power, clock, and sleep functions.
 *
 * Functions in this file facilitate configuration of ESP32's RTC_CNTL peripheral.
 * RTC_CNTL peripheral handles many functions:
 * - enables/disables clocks and power to various parts of the chip; this is
 *   done using direct register access (forcing power up or power down) or by
 *   allowing state machines to control power and clocks automatically
 * - handles sleep and wakeup functions
 * - maintains a 48-bit counter which can be used for timekeeping
 *
 * These functions are not thread safe, and should not be viewed as high level
 * APIs. For example, while this file provides a function which can switch
 * CPU frequency, this function is on its own is not sufficient to implement
 * frequency switching in ESP-IDF context: some coordination with RTOS,
 * peripheral drivers, and WiFi/BT stacks is also required.
 *
 * These functions will normally not be used in applications directly.
 * ESP-IDF provides, or will provide, drivers and other facilities to use
 * RTC subsystem functionality.
 *
 * The functions are loosely split into the following groups:
 * - rtc_clk: clock switching, calibration
 * - rtc_time: reading RTC counter, conversion between counter values and time
 * - rtc_sleep: entry into sleep modes
 * - rtc_init: initialization
 */

#define MHZ (1000000)

#define RTC_SLOW_CLK_X32K_CAL_TIMEOUT_THRES(cycles)  (cycles << 12)
#define RTC_SLOW_CLK_8MD256_CAL_TIMEOUT_THRES(cycles)  (cycles << 12)
#define RTC_SLOW_CLK_150K_CAL_TIMEOUT_THRES(cycles)  (cycles << 10)

#define OTHER_BLOCKS_POWERUP        1
#define OTHER_BLOCKS_WAIT           1

/* Approximate mapping of voltages to RTC_CNTL_DBIAS_WAK, RTC_CNTL_DBIAS_SLP,
 * RTC_CNTL_DIG_DBIAS_WAK, RTC_CNTL_DIG_DBIAS_SLP values.
 */
#define RTC_CNTL_DBIAS_SLP  5 //sleep dig_dbias & rtc_dbias
#define RTC_CNTL_DBIAS_0V90 13 //digital voltage
#define RTC_CNTL_DBIAS_0V95 16
#define RTC_CNTL_DBIAS_1V00 18
#define RTC_CNTL_DBIAS_1V05 20
#define RTC_CNTL_DBIAS_1V10 23
#define RTC_CNTL_DBIAS_1V15 25
#define RTC_CNTL_DBIAS_1V20 28
#define RTC_CNTL_DBIAS_1V25 30
#define RTC_CNTL_DBIAS_1V30 31 //voltage is about 1.34v in fact

/* Delays for various clock sources to be enabled/switched.
 * All values are in microseconds.
 */
#define SOC_DELAY_RTC_FAST_CLK_SWITCH       3
#define SOC_DELAY_RTC_SLOW_CLK_SWITCH       300
#define SOC_DELAY_RC_FAST_ENABLE            50
#define SOC_DELAY_RC_FAST_DIGI_SWITCH       5

/* Core voltage:
 * Currently, ESP32C3 never adjust its wake voltage in runtime
 * Only sets dig/rtc voltage dbias at startup time
 */
#define DIG_DBIAS_80M       RTC_CNTL_DBIAS_1V20
#define DIG_DBIAS_160M      RTC_CNTL_DBIAS_1V20
#define DIG_DBIAS_XTAL      RTC_CNTL_DBIAS_1V10
#define DIG_DBIAS_2M        RTC_CNTL_DBIAS_1V00

#define RTC_CNTL_PLL_BUF_WAIT_DEFAULT  20
#define RTC_CNTL_XTL_BUF_WAIT_DEFAULT  100
#define RTC_CNTL_CK8M_WAIT_DEFAULT  20
#define RTC_CK8M_ENABLE_WAIT_DEFAULT 5

#define RTC_CNTL_CK8M_DFREQ_DEFAULT 100
#define RTC_CNTL_SCK_DCAP_DEFAULT   255

/* Various delays to be programmed into power control state machines */
#define RTC_CNTL_XTL_BUF_WAIT_SLP_US            (250)
#define RTC_CNTL_PLL_BUF_WAIT_SLP_CYCLES        (1)
#define RTC_CNTL_CK8M_WAIT_SLP_CYCLES           (4)
#define RTC_CNTL_WAKEUP_DELAY_CYCLES            (5)
#define RTC_CNTL_OTHER_BLOCKS_POWERUP_CYCLES    (1)
#define RTC_CNTL_OTHER_BLOCKS_WAIT_CYCLES       (1)

/*
set sleep_init default param
*/
#define RTC_CNTL_DBG_ATTEN_LIGHTSLEEP_DEFAULT  5
#define RTC_CNTL_DBG_ATTEN_LIGHTSLEEP_NODROP  0
#define RTC_CNTL_DBG_ATTEN_DEEPSLEEP_DEFAULT  15
#define RTC_CNTL_DBG_ATTEN_MONITOR_DEFAULT  0
#define RTC_CNTL_BIASSLP_MONITOR_DEFAULT  0
#define RTC_CNTL_BIASSLP_SLEEP_ON  0
#define RTC_CNTL_BIASSLP_SLEEP_DEFAULT  1
#define RTC_CNTL_PD_CUR_MONITOR_DEFAULT  0
#define RTC_CNTL_PD_CUR_SLEEP_ON  0
#define RTC_CNTL_PD_CUR_SLEEP_DEFAULT  1
#define RTC_CNTL_DG_VDD_DRV_B_SLP_DEFAULT 254

/*
The follow value is used to get a reasonable rtc voltage dbias value according to digital dbias & some other value
storing in efuse (based on ATE 5k ECO3 chips)
*/
#define K_RTC_MID_MUL10000 215
#define K_DIG_MID_MUL10000 213
#define V_RTC_MID_MUL10000  10800
#define V_DIG_MID_MUL10000  10860

/**
 * @brief Possible main XTAL frequency values.
 *
 * Enum values should be equal to frequency in MHz.
 */
typedef enum {
    RTC_XTAL_FREQ_32M = 32,
    RTC_XTAL_FREQ_40M = 40,     //!< 40 MHz XTAL
} rtc_xtal_freq_t;

/**
 * @brief CPU clock configuration structure
 */
typedef struct rtc_cpu_freq_config_s {
    soc_cpu_clk_src_t source;       //!< The clock from which CPU clock is derived
    uint32_t source_freq_mhz;       //!< Source clock frequency
    uint32_t div;                   //!< Divider, freq_mhz = source_freq_mhz / div
    uint32_t freq_mhz;              //!< CPU clock frequency
} rtc_cpu_freq_config_t;

#define RTC_CLK_CAL_FRACT  19  //!< Number of fractional bits in values returned by rtc_clk_cal

#define RTC_VDDSDIO_TIEH_1_8V 0 //!< TIEH field value for 1.8V VDDSDIO
#define RTC_VDDSDIO_TIEH_3_3V 1 //!< TIEH field value for 3.3V VDDSDIO

/**
 * @brief Clock source to be calibrated using rtc_clk_cal function
 */
typedef enum {
    RTC_CAL_RTC_MUX = 0,       //!< Currently selected RTC SLOW_CLK
    RTC_CAL_8MD256 = 1,        //!< Internal 8 MHz RC oscillator, divided by 256
    RTC_CAL_32K_XTAL = 2,      //!< External 32 kHz XTAL
    RTC_CAL_INTERNAL_OSC = 3   //!< Internal 150 kHz oscillator
} rtc_cal_sel_t;

/**
 * Initialization parameters for rtc_clk_init
 */
typedef struct {
    rtc_xtal_freq_t xtal_freq : 8;             //!< Main XTAL frequency
    uint32_t cpu_freq_mhz : 10;                //!< CPU frequency to set, in MHz
    soc_rtc_fast_clk_src_t fast_clk_src : 2;   //!< RTC_FAST_CLK clock source to choose
    soc_rtc_slow_clk_src_t slow_clk_src : 2;   //!< RTC_SLOW_CLK clock source to choose
    uint32_t clk_rtc_clk_div : 8;
    uint32_t clk_8m_clk_div : 3;               //!< RTC 8M clock divider (division is by clk_8m_div+1, i.e. 0 means 8MHz frequency)
    uint32_t slow_clk_dcap : 8;                //!< RTC 150k clock adjustment parameter (higher value leads to lower frequency)
    uint32_t clk_8m_dfreq : 8;                 //!< RTC 8m clock adjustment parameter (higher value leads to higher frequency)
} rtc_clk_config_t;

/**
 * Default initializer for rtc_clk_config_t
 */
#define RTC_CLK_CONFIG_DEFAULT() { \
    .xtal_freq = CONFIG_XTAL_FREQ, \
    .cpu_freq_mhz = 80, \
    .fast_clk_src = SOC_RTC_FAST_CLK_SRC_RC_FAST, \
    .slow_clk_src = SOC_RTC_SLOW_CLK_SRC_RC_SLOW, \
    .clk_rtc_clk_div = 0, \
    .clk_8m_clk_div = 0, \
    .slow_clk_dcap = RTC_CNTL_SCK_DCAP_DEFAULT, \
    .clk_8m_dfreq = RTC_CNTL_CK8M_DFREQ_DEFAULT, \
}

typedef struct {
    uint16_t wifi_powerup_cycles : 7;
    uint16_t wifi_wait_cycles : 9;
    uint16_t bt_powerup_cycles : 7;
    uint16_t bt_wait_cycles : 9;
    uint16_t cpu_top_powerup_cycles : 7;
    uint16_t cpu_top_wait_cycles : 9;
    uint16_t dg_wrap_powerup_cycles : 7;
    uint16_t dg_wrap_wait_cycles : 9;
    uint16_t dg_peri_powerup_cycles : 7;
    uint16_t dg_peri_wait_cycles : 9;
} rtc_init_config_t;

#define RTC_INIT_CONFIG_DEFAULT() { \
    .wifi_powerup_cycles = OTHER_BLOCKS_POWERUP, \
    .wifi_wait_cycles = OTHER_BLOCKS_WAIT, \
    .bt_powerup_cycles = OTHER_BLOCKS_POWERUP, \
    .bt_wait_cycles = OTHER_BLOCKS_WAIT, \
    .cpu_top_powerup_cycles = OTHER_BLOCKS_POWERUP, \
    .cpu_top_wait_cycles = OTHER_BLOCKS_WAIT, \
    .dg_wrap_powerup_cycles = OTHER_BLOCKS_POWERUP, \
    .dg_wrap_wait_cycles = OTHER_BLOCKS_WAIT, \
    .dg_peri_powerup_cycles = OTHER_BLOCKS_POWERUP, \
    .dg_peri_wait_cycles = OTHER_BLOCKS_WAIT, \
}

void rtc_clk_divider_set(uint32_t div);

void rtc_clk_8m_divider_set(uint32_t div);

/**
 * Initialize clocks and set CPU frequency
 *
 * @param cfg clock configuration as rtc_clk_config_t
 */
void rtc_clk_init(rtc_clk_config_t cfg);

/**
 * @brief Get main XTAL frequency
 *
 * This is the value stored in RTC register RTC_XTAL_FREQ_REG by the bootloader. As passed to
 * rtc_clk_init function
 *
 * @return XTAL frequency, one of rtc_xtal_freq_t
 */
rtc_xtal_freq_t rtc_clk_xtal_freq_get(void);

/**
 * @brief Update XTAL frequency
 *
 * Updates the XTAL value stored in RTC_XTAL_FREQ_REG. Usually this value is ignored
 * after startup.
 *
 * @param xtal_freq New frequency value
 */
void rtc_clk_xtal_freq_update(rtc_xtal_freq_t xtal_freq);

/**
 * @brief Enable or disable 32 kHz XTAL oscillator
 * @param en  true to enable, false to disable
 */
void rtc_clk_32k_enable(bool en);

/**
 * @brief Configure 32 kHz XTAL oscillator to accept external clock signal
 */
void rtc_clk_32k_enable_external(void);

/**
 * @brief Get the state of 32k XTAL oscillator
 * @return true if 32k XTAL oscillator has been enabled
 */
bool rtc_clk_32k_enabled(void);

/**
 * @brief Enable 32k oscillator, configuring it for fast startup time.
 * Note: to achieve higher frequency stability, rtc_clk_32k_enable function
 * must be called one the 32k XTAL oscillator has started up. This function
 * will initially disable the 32k XTAL oscillator, so it should not be called
 * when the system is using 32k XTAL as RTC_SLOW_CLK.
 *
 * @param cycle Number of 32kHz cycles to bootstrap external crystal.
 *              If 0, no square wave will be used to bootstrap crystal oscillation.
 */
void rtc_clk_32k_bootstrap(uint32_t cycle);

/**
 * @brief Enable or disable 8 MHz internal oscillator
 *
 * Output from 8 MHz internal oscillator is passed into a configurable
 * divider, which by default divides the input clock frequency by 256.
 * Output of the divider may be used as RTC_SLOW_CLK source.
 * Output of the divider is referred to in register descriptions and code as
 * 8md256 or simply d256. Divider values other than 256 may be configured, but
 * this facility is not currently needed, so is not exposed in the code.
 *
 * When 8MHz/256 divided output is not needed, the divider should be disabled
 * to reduce power consumption.
 *
 * @param clk_8m_en true to enable 8MHz generator
 * @param d256_en true to enable /256 divider
 */
void rtc_clk_8m_enable(bool clk_8m_en, bool d256_en);

/**
 * @brief Get the state of 8 MHz internal oscillator
 * @return true if the oscillator is enabled
 */
bool rtc_clk_8m_enabled(void);

/**
 * @brief Get the state of /256 divider which is applied to 8MHz clock
 * @return true if the divided output is enabled
 */
bool rtc_clk_8md256_enabled(void);

/**
 * @brief Select source for RTC_SLOW_CLK
 * @param clk_src clock source (one of soc_rtc_slow_clk_src_t values)
 */
void rtc_clk_slow_src_set(soc_rtc_slow_clk_src_t clk_src);

/**
 * @brief Get the RTC_SLOW_CLK source
 * @return currently selected clock source (one of soc_rtc_slow_clk_src_t values)
 */
soc_rtc_slow_clk_src_t rtc_clk_slow_src_get(void);

/**
 * @brief Get the approximate frequency of RTC_SLOW_CLK, in Hz
 *
 * - if SOC_RTC_SLOW_CLK_SRC_RC_SLOW is selected, returns ~150000
 * - if SOC_RTC_SLOW_CLK_SRC_XTAL32K is selected, returns 32768
 * - if SOC_RTC_SLOW_CLK_SRC_RC_FAST_D256 is selected, returns ~68000
 *
 * rtc_clk_cal function can be used to get more precise value by comparing
 * RTC_SLOW_CLK frequency to the frequency of main XTAL.
 *
 * @return RTC_SLOW_CLK frequency, in Hz
 */
uint32_t rtc_clk_slow_freq_get_hz(void);

/**
 * @brief Select source for RTC_FAST_CLK
 * @param clk_src clock source (one of soc_rtc_fast_clk_src_t values)
 */
void rtc_clk_fast_src_set(soc_rtc_fast_clk_src_t clk_src);

/**
 * @brief Get the RTC_FAST_CLK source
 * @return currently selected clock source (one of soc_rtc_fast_clk_src_t values)
 */
soc_rtc_fast_clk_src_t rtc_clk_fast_src_get(void);

/**
 * @brief Get CPU frequency config for a given frequency
 * @param freq_mhz  Frequency in MHz
 * @param[out] out_config Output, CPU frequency configuration structure
 * @return true if frequency can be obtained, false otherwise
 */
bool rtc_clk_cpu_freq_mhz_to_config(uint32_t freq_mhz, rtc_cpu_freq_config_t *out_config);

/**
 * @brief Switch CPU frequency
 *
 * This function sets CPU frequency according to the given configuration
 * structure. It enables PLLs, if necessary.
 *
 * @note This function in not intended to be called by applications in FreeRTOS
 * environment. This is because it does not adjust various timers based on the
 * new CPU frequency.
 *
 * @param config  CPU frequency configuration structure
 */
void rtc_clk_cpu_freq_set_config(const rtc_cpu_freq_config_t *config);

/**
 * @brief Switch CPU frequency (optimized for speed)
 *
 * This function is a faster equivalent of rtc_clk_cpu_freq_set_config.
 * It works faster because it does not disable PLLs when switching from PLL to
 * XTAL and does not enabled them when switching back. If PLL is not already
 * enabled when this function is called to switch from XTAL to PLL frequency,
 * or the PLL which is enabled is the wrong one, this function will fall back
 * to calling rtc_clk_cpu_freq_set_config.
 *
 * Unlike rtc_clk_cpu_freq_set_config, this function relies on static data,
 * so it is less safe to use it e.g. from a panic handler (when memory might
 * be corrupted).
 *
 * @note This function in not intended to be called by applications in FreeRTOS
 * environment. This is because it does not adjust various timers based on the
 * new CPU frequency.
 *
 * @param config  CPU frequency configuration structure
 */
void rtc_clk_cpu_freq_set_config_fast(const rtc_cpu_freq_config_t *config);

/**
 * @brief Get the currently used CPU frequency configuration
 * @param[out] out_config  Output, CPU frequency configuration structure
 */
void rtc_clk_cpu_freq_get_config(rtc_cpu_freq_config_t *out_config);

/**
 * @brief Switch CPU clock source to XTAL
 *
 * Short form for filling in rtc_cpu_freq_config_t structure and calling
 * rtc_clk_cpu_freq_set_config when a switch to XTAL is needed.
 * Assumes that XTAL frequency has been determined — don't call in startup code.
 */
void rtc_clk_cpu_freq_set_xtal(void);

/**
 * @brief Store new APB frequency value into RTC_APB_FREQ_REG
 *
 * This function doesn't change any hardware clocks.
 *
 * Functions which perform frequency switching and change APB frequency call
 * this function to update the value of APB frequency stored in RTC_APB_FREQ_REG
 * (one of RTC general purpose retention registers). This should not normally
 * be called from application code.
 *
 * @param apb_freq  new APB frequency, in Hz
 */
void rtc_clk_apb_freq_update(uint32_t apb_freq);

/**
 * @brief Get the current stored APB frequency.
 * @return The APB frequency value as last set via rtc_clk_apb_freq_update(), in Hz.
 */
uint32_t rtc_clk_apb_freq_get(void);

uint32_t rtc_clk_cal_internal(rtc_cal_sel_t cal_clk, uint32_t slowclk_cycles);

/**
 * @brief Measure RTC slow clock's period, based on main XTAL frequency
 *
 * This function will time out and return 0 if the time for the given number
 * of cycles to be counted exceeds the expected time twice. This may happen if
 * 32k XTAL is being calibrated, but the oscillator has not started up (due to
 * incorrect loading capacitance, board design issue, or lack of 32 XTAL on board).
 *
 * @note When 32k CLK is being calibrated, this function will check the accuracy
 * of the clock. Since the xtal 32k or ext osc 32k is generally very stable, if
 * the check fails, then consider this an invalid 32k clock and return 0. This
 * check can filter some jamming signal.
 *
 * @param cal_clk  clock to be measured
 * @param slow_clk_cycles  number of slow clock cycles to average
 * @return average slow clock period in microseconds, Q13.19 fixed point format,
 *         or 0 if calibration has timed out
 */
uint32_t rtc_clk_cal(rtc_cal_sel_t cal_clk, uint32_t slow_clk_cycles);

/**
 * @brief Measure ratio between XTAL frequency and RTC slow clock frequency
 * @param cal_clk slow clock to be measured
 * @param slow_clk_cycles number of slow clock cycles to average
 * @return average ratio between XTAL frequency and slow clock frequency,
 *         Q13.19 fixed point format, or 0 if calibration has timed out.
 */
uint32_t rtc_clk_cal_ratio(rtc_cal_sel_t cal_clk, uint32_t slow_clk_cycles);

/**
 * @brief Convert time interval from microseconds to RTC_SLOW_CLK cycles
 * @param time_in_us Time interval in microseconds
 * @param slow_clk_period  Period of slow clock in microseconds, Q13.19
 *                         fixed point format (as returned by rtc_slowck_cali).
 * @return number of slow clock cycles
 */
uint64_t rtc_time_us_to_slowclk(uint64_t time_in_us, uint32_t period);

/**
 * @brief Convert time interval from RTC_SLOW_CLK to microseconds
 * @param time_in_us Time interval in RTC_SLOW_CLK cycles
 * @param slow_clk_period  Period of slow clock in microseconds, Q13.19
 *                         fixed point format (as returned by rtc_slowck_cali).
 * @return time interval in microseconds
 */
uint64_t rtc_time_slowclk_to_us(uint64_t rtc_cycles, uint32_t period);

/**
 * @brief Get current value of RTC counter
 *
 * RTC has a 48-bit counter which is incremented by 2 every 2 RTC_SLOW_CLK
 * cycles. Counter value is not writable by software. The value is not adjusted
 * when switching to a different RTC_SLOW_CLK source.
 *
 * Note: this function may take up to 1 RTC_SLOW_CLK cycle to execute
 *
 * @return current value of RTC counter
 */
uint64_t rtc_time_get(void);

uint64_t rtc_light_slp_time_get(void);

uint64_t rtc_deep_slp_time_get(void);

/**
 * @brief Busy loop until next RTC_SLOW_CLK cycle
 *
 * This function returns not earlier than the next RTC_SLOW_CLK clock cycle.
 * In some cases (e.g. when RTC_SLOW_CLK cycle is very close), it may return
 * one RTC_SLOW_CLK cycle later.
 */
void rtc_clk_wait_for_slow_cycle(void);

/**
 * @brief Enable the rtc digital 8M clock
 *
 * This function is used to enable the digital rtc 8M clock to support peripherals.
 * For enabling the analog 8M clock, using `rtc_clk_8M_enable` function above.
 */
void rtc_dig_clk8m_enable(void);

/**
 * @brief Disable the rtc digital 8M clock
 *
 * This function is used to disable the digital rtc 8M clock, which is only used to support peripherals.
 */
void rtc_dig_clk8m_disable(void);

/**
 * @brief Get whether the rtc digital 8M clock is enabled
 */
bool rtc_dig_8m_enabled(void);

/**
 * @brief Calculate the real clock value after the clock calibration
 *
 * @param cal_val Average slow clock period in microseconds, fixed point value as returned from `rtc_clk_cal`
 * @return Frequency of the clock in Hz
 */
uint32_t rtc_clk_freq_cal(uint32_t cal_val);

/**
 * @brief Power down flags for rtc_sleep_pd function
 */
typedef struct {
    uint32_t dig_fpu : 1;    //!< Set to 1 to power UP digital part in sleep
    uint32_t rtc_fpu : 1;    //!< Set to 1 to power UP RTC memories in sleep
    uint32_t cpu_fpu : 1;    //!< Set to 1 to power UP digital memories and CPU in sleep
    uint32_t i2s_fpu : 1;    //!< Set to 1 to power UP I2S in sleep
    uint32_t bb_fpu : 1;     //!< Set to 1 to power UP WiFi in sleep
    uint32_t nrx_fpu : 1;    //!< Set to 1 to power UP WiFi in sleep
    uint32_t fe_fpu : 1;     //!< Set to 1 to power UP WiFi in sleep
    uint32_t sram_fpu : 1;    //!< Set to 1 to power UP SRAM in sleep
    uint32_t rom_ram_fpu : 1; //!< Set to 1 to power UP ROM/IRAM0_DRAM0 in sleep
} rtc_sleep_pu_config_t;

/**
 * Initializer for rtc_sleep_pu_config_t which sets all flags to the same value
 */
#define RTC_SLEEP_PU_CONFIG_ALL(val) {\
    .dig_fpu = (val), \
    .rtc_fpu = (val), \
    .cpu_fpu = (val), \
    .i2s_fpu = (val), \
    .bb_fpu = (val), \
    .nrx_fpu = (val), \
    .fe_fpu = (val), \
    .sram_fpu = (val), \
    .rom_ram_fpu = (val), \
}

void rtc_sleep_pu(rtc_sleep_pu_config_t cfg);

/**
 * @brief sleep configuration for rtc_sleep_init function
 */
typedef struct {
    uint32_t lslp_mem_inf_fpu : 1;      //!< force normal voltage in sleep mode (digital domain memory)
    uint32_t rtc_mem_inf_follow_cpu : 1;//!< keep low voltage in sleep mode (even if ULP/touch is used)
    uint32_t rtc_fastmem_pd_en : 1;     //!< power down RTC fast memory
    uint32_t rtc_slowmem_pd_en : 1;     //!< power down RTC slow memory
    uint32_t rtc_peri_pd_en : 1;        //!< power down RTC peripherals
    uint32_t wifi_pd_en : 1;            //!< power down WiFi
    uint32_t bt_pd_en : 1;              //!< power down BT
    uint32_t cpu_pd_en : 1;             //!< power down CPU, but not restart when lightsleep.
    uint32_t int_8m_pd_en : 1;          //!< Power down Internal 8M oscillator
    uint32_t dig_peri_pd_en : 1;        //!< power down digital peripherals
    uint32_t deep_slp : 1;              //!< power down digital domain
    uint32_t wdt_flashboot_mod_en : 1;  //!< enable WDT flashboot mode
    uint32_t dig_dbias_wak : 5;         //!< set bias for digital domain, in active mode
    uint32_t dig_dbias_slp : 5;         //!< set bias for digital domain, in sleep mode
    uint32_t rtc_dbias_wak : 5;         //!< set bias for RTC domain, in active mode
    uint32_t rtc_dbias_slp : 5;         //!< set bias for RTC domain, in sleep mode
    uint32_t dbg_atten_monitor : 4;     //!< voltage parameter, in monitor mode
    uint32_t bias_sleep_monitor : 1;    //!< circuit control parameter, in monitor mode
    uint32_t dbg_atten_slp : 4;         //!< voltage parameter, in sleep mode
    uint32_t bias_sleep_slp : 1;        //!< circuit control parameter, in sleep mode
    uint32_t pd_cur_monitor : 1;        //!< circuit control parameter, in monitor mode
    uint32_t pd_cur_slp : 1;            //!< circuit control parameter, in sleep mode
    uint32_t vddsdio_pd_en : 1;         //!< power down VDDSDIO regulator
    uint32_t xtal_fpu : 1;              //!< keep main XTAL powered up in sleep
    uint32_t deep_slp_reject : 1;       //!< enable deep sleep reject
    uint32_t light_slp_reject : 1;      //!< enable light sleep reject
} rtc_sleep_config_t;

#define RTC_SLEEP_PD_DIG                BIT(0)  //!< Deep sleep (power down digital domain)
#define RTC_SLEEP_PD_RTC_PERIPH         BIT(1)  //!< Power down RTC peripherals
#define RTC_SLEEP_PD_RTC_SLOW_MEM       BIT(2)  //!< Power down RTC SLOW memory
#define RTC_SLEEP_PD_RTC_FAST_MEM       BIT(3)  //!< Power down RTC FAST memory
#define RTC_SLEEP_PD_RTC_MEM_FOLLOW_CPU BIT(4)  //!< RTC FAST and SLOW memories are automatically powered up and down along with the CPU
#define RTC_SLEEP_PD_VDDSDIO            BIT(5)  //!< Power down VDDSDIO regulator
#define RTC_SLEEP_PD_WIFI               BIT(6)  //!< Power down WIFI
#define RTC_SLEEP_PD_BT                 BIT(7)  //!< Power down BT
#define RTC_SLEEP_PD_CPU                BIT(8)  //!< Power down CPU when in lightsleep, but not restart
#define RTC_SLEEP_PD_DIG_PERIPH         BIT(9)  //!< Power down DIG peripherals
#define RTC_SLEEP_PD_INT_8M             BIT(10) //!< Power down Internal 8M oscillator
#define RTC_SLEEP_PD_XTAL               BIT(11) //!< Power down main XTAL

//These flags are not power domains, but will affect some sleep parameters
#define RTC_SLEEP_DIG_USE_8M            BIT(16)
#define RTC_SLEEP_USE_ADC_TESEN_MONITOR BIT(17)
#define RTC_SLEEP_NO_ULTRA_LOW          BIT(18) //!< Avoid using ultra low power in deep sleep, in which RTCIO cannot be used as input, and RTCMEM can't work under high temperature

/**
 * Default initializer for rtc_sleep_config_t
 *
 * This initializer sets all fields to "reasonable" values (e.g. suggested for
 * production use) based on a combination of RTC_SLEEP_PD_x flags.
 *
 * @param RTC_SLEEP_PD_x flags combined using bitwise OR
 */
void rtc_sleep_get_default_config(uint32_t sleep_flags, rtc_sleep_config_t *out_config);

/**
 * @brief Prepare the chip to enter sleep mode
 *
 * This function configures various power control state machines to handle
 * entry into light sleep or deep sleep mode, switches APB and CPU clock source
 * (usually to XTAL), and sets bias voltages for digital and RTC power domains.
 *
 * This function does not actually enter sleep mode; this is done using
 * rtc_sleep_start function. Software may do some other actions between
 * rtc_sleep_init and rtc_sleep_start, such as set wakeup timer and configure
 * wakeup sources.
 * @param cfg sleep mode configuration
 */
void rtc_sleep_init(rtc_sleep_config_t cfg);

/**
 * @brief Low level initialize for rtc state machine waiting cycles after waking up
 *
 * This function configures the cycles chip need to wait for internal 8MHz
 * oscillator and external 40MHz crystal. As we configure fixed time for waiting
 * crystal, we need to pass period to calculate cycles. Now this function only
 * used in lightsleep mode.
 *
 * @param slowclk_period re-calibrated slow clock period
 */
void rtc_sleep_low_init(uint32_t slowclk_period);

/**
 * @brief Set target value of RTC counter for RTC_TIMER_TRIG_EN wakeup source
 * @param t value of RTC counter at which wakeup from sleep will happen;
 *          only the lower 48 bits are used
 */
void rtc_sleep_set_wakeup_time(uint64_t t);

#define RTC_GPIO_TRIG_EN            BIT(2)  //!< GPIO wakeup
#define RTC_TIMER_TRIG_EN           BIT(3)  //!< Timer wakeup
#define RTC_WIFI_TRIG_EN            BIT(5)  //!< WIFI wakeup (light sleep only)
#define RTC_UART0_TRIG_EN           BIT(6)  //!< UART0 wakeup (light sleep only)
#define RTC_UART1_TRIG_EN           BIT(7)  //!< UART1 wakeup (light sleep only)
#define RTC_BT_TRIG_EN              BIT(10) //!< BT wakeup (light sleep only)
#define RTC_XTAL32K_DEAD_TRIG_EN    BIT(12)
#define RTC_USB_TRIG_EN             BIT(14)
#define RTC_BROWNOUT_DET_TRIG_EN    BIT(16)

/**
 * RTC_SLEEP_REJECT_MASK records sleep reject sources supported by chip
 */
#define RTC_SLEEP_REJECT_MASK (RTC_GPIO_TRIG_EN         | \
                               RTC_TIMER_TRIG_EN        | \
                               RTC_WIFI_TRIG_EN         | \
                               RTC_UART0_TRIG_EN        | \
                               RTC_UART1_TRIG_EN        | \
                               RTC_BT_TRIG_EN           | \
                               RTC_XTAL32K_DEAD_TRIG_EN | \
                               RTC_USB_TRIG_EN          | \
                               RTC_BROWNOUT_DET_TRIG_EN)

/**
 * @brief Enter deep or light sleep mode
 *
 * This function enters the sleep mode previously configured using rtc_sleep_init
 * function. Before entering sleep, software should configure wake up sources
 * appropriately (set up GPIO wakeup registers, timer wakeup registers,
 * and so on).
 *
 * If deep sleep mode was configured using rtc_sleep_init, and sleep is not
 * rejected by hardware (based on reject_opt flags), this function never returns.
 * When the chip wakes up from deep sleep, CPU is reset and execution starts
 * from ROM bootloader.
 *
 * If light sleep mode was configured using rtc_sleep_init, this function
 * returns on wakeup, or if sleep is rejected by hardware.
 *
 * @param wakeup_opt  bit mask wake up reasons to enable (RTC_xxx_TRIG_EN flags
 *                    combined with OR)
 * @param reject_opt  bit mask of sleep reject reasons:
 *                      - RTC_CNTL_GPIO_REJECT_EN
 *                      - RTC_CNTL_SDIO_REJECT_EN
 *                    These flags are used to prevent entering sleep when e.g.
 *                    an external host is communicating via SDIO slave
 * @return non-zero if sleep was rejected by hardware
 */
uint32_t rtc_sleep_start(uint32_t wakeup_opt, uint32_t reject_opt, uint32_t lslp_mem_inf_fpu);

/**
 * @brief Enter deep sleep mode
 *
 * Similar to rtc_sleep_start(), but additionally uses hardware to calculate the CRC value
 * of RTC FAST memory. On wake, this CRC is used to determine if a deep sleep wake
 * stub is valid to execute (if a wake address is set).
 *
 * No RAM is accessed while calculating the CRC and going into deep sleep, which makes
 * this function safe to use even if the caller's stack is in RTC FAST memory.
 *
 * @note If no deep sleep wake stub address is set then calling rtc_sleep_start() will
 * have the same effect and takes less time as CRC calculation is skipped.
 *
 * @note This function should only be called after rtc_sleep_init() has been called to
 * configure the system for deep sleep.
 *
 * @param wakeup_opt - same as for rtc_sleep_start
 * @param reject_opt - same as for rtc_sleep_start
 *
 * @return non-zero if sleep was rejected by hardware
 */
uint32_t rtc_deep_sleep_start(uint32_t wakeup_opt, uint32_t reject_opt);

/**
 * RTC power and clock control initialization settings
 */
typedef struct {
    uint32_t ck8m_wait : 8;         //!< Number of rtc_fast_clk cycles to wait for 8M clock to be ready
    uint32_t xtal_wait : 8;         //!< Number of rtc_fast_clk cycles to wait for XTAL clock to be ready
    uint32_t pll_wait : 8;          //!< Number of rtc_fast_clk cycles to wait for PLL to be ready
    uint32_t clkctl_init : 1;       //!< Perform clock control related initialization
    uint32_t pwrctl_init : 1;       //!< Perform power control related initialization
    uint32_t rtc_dboost_fpd : 1;    //!< Force power down RTC_DBOOST
    uint32_t xtal_fpu : 1;
    uint32_t bbpll_fpu : 1;
    uint32_t cpu_waiti_clk_gate : 1;
    uint32_t cali_ocode : 1;        //!< Calibrate Ocode to make bangap voltage more precise.
} rtc_config_t;

/**
 * Default initializer of rtc_config_t.
 *
 * This initializer sets all fields to "reasonable" values (e.g. suggested for
 * production use).
 */
#define RTC_CONFIG_DEFAULT() {\
    .ck8m_wait = RTC_CNTL_CK8M_WAIT_DEFAULT, \
    .xtal_wait = RTC_CNTL_XTL_BUF_WAIT_DEFAULT, \
    .pll_wait  = RTC_CNTL_PLL_BUF_WAIT_DEFAULT, \
    .clkctl_init = 1, \
    .pwrctl_init = 1, \
    .rtc_dboost_fpd = 1, \
    .xtal_fpu = 0, \
    .bbpll_fpu = 0, \
    .cpu_waiti_clk_gate = 1, \
    .cali_ocode = 0\
}

/**
 * Initialize RTC clock and power control related functions
 * @param cfg configuration options as rtc_config_t
 */
void rtc_init(rtc_config_t cfg);

/**
 * Structure describing vddsdio configuration
 */
typedef struct {
    uint32_t force : 1;     //!< If 1, use configuration from RTC registers; if 0, use EFUSE/bootstrapping pins.
    uint32_t enable : 1;    //!< Enable VDDSDIO regulator
    uint32_t tieh  : 1;     //!< Select VDDSDIO voltage. One of RTC_VDDSDIO_TIEH_1_8V, RTC_VDDSDIO_TIEH_3_3V
    uint32_t drefh : 2;     //!< Tuning parameter for VDDSDIO regulator
    uint32_t drefm : 2;     //!< Tuning parameter for VDDSDIO regulator
    uint32_t drefl : 2;     //!< Tuning parameter for VDDSDIO regulator
} rtc_vddsdio_config_t;

/**
 * Get current VDDSDIO configuration
 * If VDDSDIO configuration is overridden by RTC, get values from RTC
 * Otherwise, if VDDSDIO is configured by EFUSE, get values from EFUSE
 * Otherwise, use default values and the level of MTDI bootstrapping pin.
 * @return currently used VDDSDIO configuration
 */
rtc_vddsdio_config_t rtc_vddsdio_get_config(void);

/**
 * Set new VDDSDIO configuration using RTC registers.
 * If config.force == 1, this overrides configuration done using bootstrapping
 * pins and EFUSE.
 *
 * @param config new VDDSDIO configuration
 */
void rtc_vddsdio_set_config(rtc_vddsdio_config_t config);


// -------------------------- CLOCK TREE DEFS ALIAS ----------------------------
// **WARNING**: The following are only for backwards compatibility.
// Please use the declarations in soc/clk_tree_defs.h instead.
/**
 * @brief CPU clock source
 */
typedef soc_cpu_clk_src_t rtc_cpu_freq_src_t;
#define RTC_CPU_FREQ_SRC_XTAL SOC_CPU_CLK_SRC_XTAL  //!< XTAL
#define RTC_CPU_FREQ_SRC_PLL SOC_CPU_CLK_SRC_PLL    //!< PLL (480M or 320M)
#define RTC_CPU_FREQ_SRC_8M SOC_CPU_CLK_SRC_RC_FAST //!< Internal 17.5M RTC oscillator

/**
 * @brief RTC SLOW_CLK frequency values
 */
typedef soc_rtc_slow_clk_src_t rtc_slow_freq_t;
#define RTC_SLOW_FREQ_RTC SOC_RTC_SLOW_CLK_SRC_RC_SLOW         //!< Internal 150 kHz RC oscillator
#define RTC_SLOW_FREQ_32K_XTAL SOC_RTC_SLOW_CLK_SRC_XTAL32K    //!< External 32 kHz XTAL
#define RTC_SLOW_FREQ_8MD256 SOC_RTC_SLOW_CLK_SRC_RC_FAST_D256 //!< Internal 17.5 MHz RC oscillator, divided by 256

/**
 * @brief RTC FAST_CLK frequency values
 */
typedef soc_rtc_fast_clk_src_t rtc_fast_freq_t;
#define RTC_FAST_FREQ_XTALD4 SOC_RTC_FAST_CLK_SRC_XTAL_DIV  //!< Main XTAL, divided by 2
#define RTC_FAST_FREQ_8M SOC_RTC_FAST_CLK_SRC_RC_FAST       //!< Internal 17.5 MHz RC oscillator

/* Alias of frequency related macros */
#define RTC_FAST_CLK_FREQ_APPROX    SOC_CLK_RC_FAST_FREQ_APPROX
#define RTC_FAST_CLK_FREQ_8M        SOC_CLK_RC_FAST_FREQ_APPROX
#define RTC_SLOW_CLK_FREQ_150K      SOC_CLK_RC_SLOW_FREQ_APPROX
#define RTC_SLOW_CLK_FREQ_8MD256    SOC_CLK_RC_FAST_D256_FREQ_APPROX
#define RTC_SLOW_CLK_FREQ_32K       SOC_CLK_XTAL32K_FREQ_APPROX

/* Alias of deprecated function names */
#define rtc_clk_slow_freq_set(slow_freq) rtc_clk_slow_src_set(slow_freq)
#define rtc_clk_slow_freq_get() rtc_clk_slow_src_get()
#define rtc_clk_fast_freq_set(fast_freq) rtc_clk_fast_src_set(fast_freq)
#define rtc_clk_fast_freq_get() rtc_clk_fast_src_get()

#ifdef __cplusplus
}
#endif