-
Notifications
You must be signed in to change notification settings - Fork 7k
/
spi_common.h
172 lines (158 loc) · 8.28 KB
/
spi_common.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
/*
* SPDX-FileCopyrightText: 2010-2022 Espressif Systems (Shanghai) CO LTD
*
* SPDX-License-Identifier: Apache-2.0
*/
#pragma once
#include <stdint.h>
#include <stdbool.h>
#include "sdkconfig.h"
#include "esp_err.h"
#include "esp_ipc.h"
#include "intr_types.h"
#include "hal/spi_types.h"
#ifdef __cplusplus
extern "C"
{
#endif
//Maximum amount of bytes that can be put in one DMA descriptor
#define SPI_MAX_DMA_LEN (4096-4)
/**
* Transform unsigned integer of length <= 32 bits to the format which can be
* sent by the SPI driver directly.
*
* E.g. to send 9 bits of data, you can:
*
* uint16_t data = SPI_SWAP_DATA_TX(0x145, 9);
*
* Then points tx_buffer to ``&data``.
*
* @param DATA Data to be sent, can be uint8_t, uint16_t or uint32_t.
* @param LEN Length of data to be sent, since the SPI peripheral sends from
* the MSB, this helps to shift the data to the MSB.
*/
#define SPI_SWAP_DATA_TX(DATA, LEN) __builtin_bswap32((uint32_t)(DATA)<<(32-(LEN)))
/**
* Transform received data of length <= 32 bits to the format of an unsigned integer.
*
* E.g. to transform the data of 15 bits placed in a 4-byte array to integer:
*
* uint16_t data = SPI_SWAP_DATA_RX(*(uint32_t*)t->rx_data, 15);
*
* @param DATA Data to be rearranged, can be uint8_t, uint16_t or uint32_t.
* @param LEN Length of data received, since the SPI peripheral writes from
* the MSB, this helps to shift the data to the LSB.
*/
#define SPI_SWAP_DATA_RX(DATA, LEN) (__builtin_bswap32(DATA)>>(32-(LEN)))
#define SPICOMMON_BUSFLAG_SLAVE 0 ///< Initialize I/O in slave mode
#define SPICOMMON_BUSFLAG_MASTER (1<<0) ///< Initialize I/O in master mode
#define SPICOMMON_BUSFLAG_IOMUX_PINS (1<<1) ///< Check using iomux pins. Or indicates the pins are configured through the IO mux rather than GPIO matrix.
#define SPICOMMON_BUSFLAG_GPIO_PINS (1<<2) ///< Force the signals to be routed through GPIO matrix. Or indicates the pins are routed through the GPIO matrix.
#define SPICOMMON_BUSFLAG_SCLK (1<<3) ///< Check existing of SCLK pin. Or indicates CLK line initialized.
#define SPICOMMON_BUSFLAG_MISO (1<<4) ///< Check existing of MISO pin. Or indicates MISO line initialized.
#define SPICOMMON_BUSFLAG_MOSI (1<<5) ///< Check existing of MOSI pin. Or indicates MOSI line initialized.
#define SPICOMMON_BUSFLAG_DUAL (1<<6) ///< Check MOSI and MISO pins can output. Or indicates bus able to work under DIO mode.
#define SPICOMMON_BUSFLAG_WPHD (1<<7) ///< Check existing of WP and HD pins. Or indicates WP & HD pins initialized.
#define SPICOMMON_BUSFLAG_QUAD (SPICOMMON_BUSFLAG_DUAL|SPICOMMON_BUSFLAG_WPHD) ///< Check existing of MOSI/MISO/WP/HD pins as output. Or indicates bus able to work under QIO mode.
#define SPICOMMON_BUSFLAG_IO4_IO7 (1<<8) ///< Check existing of IO4~IO7 pins. Or indicates IO4~IO7 pins initialized.
#define SPICOMMON_BUSFLAG_OCTAL (SPICOMMON_BUSFLAG_QUAD|SPICOMMON_BUSFLAG_IO4_IO7) ///< Check existing of MOSI/MISO/WP/HD/SPIIO4/SPIIO5/SPIIO6/SPIIO7 pins as output. Or indicates bus able to work under octal mode.
#define SPICOMMON_BUSFLAG_NATIVE_PINS SPICOMMON_BUSFLAG_IOMUX_PINS
/**
* @brief SPI DMA channels
*/
typedef enum {
SPI_DMA_DISABLED = 0, ///< Do not enable DMA for SPI
#if CONFIG_IDF_TARGET_ESP32
SPI_DMA_CH1 = 1, ///< Enable DMA, select DMA Channel 1
SPI_DMA_CH2 = 2, ///< Enable DMA, select DMA Channel 2
#endif
SPI_DMA_CH_AUTO = 3, ///< Enable DMA, channel is automatically selected by driver
} spi_common_dma_t;
#if __cplusplus
/* Needed for C++ backwards compatibility with earlier ESP-IDF where this argument is a bare 'int'. Can be removed in ESP-IDF 5 */
typedef int spi_dma_chan_t;
#else
typedef spi_common_dma_t spi_dma_chan_t;
#endif
/**
* @brief This is a configuration structure for a SPI bus.
*
* You can use this structure to specify the GPIO pins of the bus. Normally, the driver will use the
* GPIO matrix to route the signals. An exception is made when all signals either can be routed through
* the IO_MUX or are -1. In that case, the IO_MUX is used, allowing for >40MHz speeds.
*
* @note Be advised that the slave driver does not use the quadwp/quadhd lines and fields in spi_bus_config_t refering to these lines will be ignored and can thus safely be left uninitialized.
*/
typedef struct {
union {
int mosi_io_num; ///< GPIO pin for Master Out Slave In (=spi_d) signal, or -1 if not used.
int data0_io_num; ///< GPIO pin for spi data0 signal in quad/octal mode, or -1 if not used.
};
union {
int miso_io_num; ///< GPIO pin for Master In Slave Out (=spi_q) signal, or -1 if not used.
int data1_io_num; ///< GPIO pin for spi data1 signal in quad/octal mode, or -1 if not used.
};
int sclk_io_num; ///< GPIO pin for SPI Clock signal, or -1 if not used.
union {
int quadwp_io_num; ///< GPIO pin for WP (Write Protect) signal, or -1 if not used.
int data2_io_num; ///< GPIO pin for spi data2 signal in quad/octal mode, or -1 if not used.
};
union {
int quadhd_io_num; ///< GPIO pin for HD (Hold) signal, or -1 if not used.
int data3_io_num; ///< GPIO pin for spi data3 signal in quad/octal mode, or -1 if not used.
};
int data4_io_num; ///< GPIO pin for spi data4 signal in octal mode, or -1 if not used.
int data5_io_num; ///< GPIO pin for spi data5 signal in octal mode, or -1 if not used.
int data6_io_num; ///< GPIO pin for spi data6 signal in octal mode, or -1 if not used.
int data7_io_num; ///< GPIO pin for spi data7 signal in octal mode, or -1 if not used.
int max_transfer_sz; ///< Maximum transfer size, in bytes. Defaults to 4092 if 0 when DMA enabled, or to `SOC_SPI_MAXIMUM_BUFFER_SIZE` if DMA is disabled.
uint32_t flags; ///< Abilities of bus to be checked by the driver. Or-ed value of ``SPICOMMON_BUSFLAG_*`` flags.
intr_cpu_id_t isr_cpu_id; ///< Select cpu core to register SPI ISR.
int intr_flags; /**< Interrupt flag for the bus to set the priority, and IRAM attribute, see
* ``esp_intr_alloc.h``. Note that the EDGE, INTRDISABLED attribute are ignored
* by the driver. Note that if ESP_INTR_FLAG_IRAM is set, ALL the callbacks of
* the driver, and their callee functions, should be put in the IRAM.
*/
} spi_bus_config_t;
/**
* @brief Initialize a SPI bus
*
* @warning SPI0/1 is not supported
*
* @param host_id SPI peripheral that controls this bus
* @param bus_config Pointer to a spi_bus_config_t struct specifying how the host should be initialized
* @param dma_chan - Selecting a DMA channel for an SPI bus allows transactions on the bus with size only limited by the amount of internal memory.
* - Selecting SPI_DMA_DISABLED limits the size of transactions.
* - Set to SPI_DMA_DISABLED if only the SPI flash uses this bus.
* - Set to SPI_DMA_CH_AUTO to let the driver to allocate the DMA channel.
*
* @warning If a DMA channel is selected, any transmit and receive buffer used should be allocated in
* DMA-capable memory.
*
* @warning The ISR of SPI is always executed on the core which calls this
* function. Never starve the ISR on this core or the SPI transactions will not
* be handled.
*
* @return
* - ESP_ERR_INVALID_ARG if configuration is invalid
* - ESP_ERR_INVALID_STATE if host already is in use
* - ESP_ERR_NOT_FOUND if there is no available DMA channel
* - ESP_ERR_NO_MEM if out of memory
* - ESP_OK on success
*/
esp_err_t spi_bus_initialize(spi_host_device_t host_id, const spi_bus_config_t *bus_config, spi_dma_chan_t dma_chan);
/**
* @brief Free a SPI bus
*
* @warning In order for this to succeed, all devices have to be removed first.
*
* @param host_id SPI peripheral to free
* @return
* - ESP_ERR_INVALID_ARG if parameter is invalid
* - ESP_ERR_INVALID_STATE if bus hasn't been initialized before, or not all devices on the bus are freed
* - ESP_OK on success
*/
esp_err_t spi_bus_free(spi_host_device_t host_id);
#ifdef __cplusplus
}
#endif