forked from meshtastic/firmware
/
variant.h
157 lines (126 loc) · 3.97 KB
/
variant.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
/*
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
Copyright (c) 2016 Sandeep Mistry All right reserved.
Copyright (c) 2018, Adafruit Industries (adafruit.com)
This library is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation; either
version 2.1 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
See the GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public
License along with this library; if not, write to the Free Software
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#pragma once
/** Master clock frequency */
#define VARIANT_MCK (64000000ul)
// This board does not have a 32khz crystal
// #define USE_LFXO // Board uses 32khz crystal for LF
#define USE_LFRC // Board uses RC for LF
/*----------------------------------------------------------------------------
* Headers
*----------------------------------------------------------------------------*/
#include "WVariant.h"
#ifdef __cplusplus
extern "C" {
#endif // __cplusplus
// Number of pins defined in PinDescription array
#define PINS_COUNT (46)
#define NUM_DIGITAL_PINS (46)
#define NUM_ANALOG_INPUTS (0)
#define NUM_ANALOG_OUTPUTS (0)
// LEDs
#define PIN_LED1 (0)
#define PIN_LED2 (1)
#define LED_BUILTIN PIN_LED1
#define LED_CONN PIN_LED2
#define LED_RED PIN_LED1
#define LED_GREEN PIN_LED2
// FIXME, bluefruit automatically blinks this led while connected. call AdafruitBluefruit::autoConnLed to change this.
#define LED_BLUE LED_GREEN
#define LED_STATE_ON 1 // State when LED is litted
/*
* Buttons
*/
#define PIN_BUTTON1 4 // center
#define PIN_BUTTON2 2
#define PIN_BUTTON3 3
#define PIN_BUTTON4 5
#define PIN_BUTTON5 6
/*
* Analog pins
*/
#define PIN_A0 (0xff)
#define PIN_A1 (0xff)
#define PIN_A2 (0xff)
#define PIN_A3 (0xff)
#define PIN_A4 (0xff)
#define PIN_A5 (0xff)
#define PIN_A6 (0xff)
#define PIN_A7 (0xff)
static const uint8_t A0 = PIN_A0;
static const uint8_t A1 = PIN_A1;
static const uint8_t A2 = PIN_A2;
static const uint8_t A3 = PIN_A3;
static const uint8_t A4 = PIN_A4;
static const uint8_t A5 = PIN_A5;
static const uint8_t A6 = PIN_A6;
static const uint8_t A7 = PIN_A7;
#define ADC_RESOLUTION 14
// Other pins
#define PIN_AREF (0xff)
//#define PIN_NFC1 (9)
//#define PIN_NFC2 (10)
static const uint8_t AREF = PIN_AREF;
/*
* Serial interfaces
*/
// GPS is on Serial1
#define PIN_SERIAL1_RX (8)
#define PIN_SERIAL1_TX (9)
// Connected to Jlink CDC
//#define PIN_SERIAL2_RX (8)
//#define PIN_SERIAL2_TX (6)
/*
* SPI Interfaces
*/
#define SPI_INTERFACES_COUNT 1
#define PIN_SPI_MISO (15)
#define PIN_SPI_MOSI (13)
#define PIN_SPI_SCK (12)
// static const uint8_t SS = 44;
static const uint8_t MOSI = PIN_SPI_MOSI;
static const uint8_t MISO = PIN_SPI_MISO;
static const uint8_t SCK = PIN_SPI_SCK;
/*
* Wire Interfaces
*/
#define WIRE_INTERFACES_COUNT 1
#define PIN_WIRE_SDA (32 + 2)
#define PIN_WIRE_SCL (32)
// CUSTOM GPIOs the SX1262
#define SX1262_CS (10)
#define SX1262_DIO1 (20)
#define SX1262_DIO2 (26)
#define SX1262_BUSY (31) // Supposed to be P0.18 but because of reworks, now on P0.31 (18)
#define SX1262_RESET (17)
// #define SX1262_ANT_SW (32 + 10)
#define SX1262_RXEN (22)
#define SX1262_TXEN (24)
#define SX1262_E22 // Indicates this SX1262 is inside of an ebyte E22 module and special config should be done for that
// ERC12864-10 LCD
#define ERC12864_CS (32 + 4)
#define ERC12864_RESET (32 + 6)
#define ERC12864_CD (32 + 9)
// L80 GPS
#define L80_PPS (28)
#define L80_RESET (29)
#ifdef __cplusplus
}
#endif
/*----------------------------------------------------------------------------
* Arduino objects - C++ only
*----------------------------------------------------------------------------*/