The Pi Network

The Pi Network

The so called Local Area Network (LAN). In order for the cluster to communicate, we need to set up a LAN switch so that each Pi board knows where to send and receive data, commands, and output results.

• Network Lookup Table
• Assign a static IP address
• Change Hostname
  • Rename the hostname
  • Mapping the hostname
  • Reboot the Pi
• Enable Secure Shell (SSH)
  • Enable SSH
    • Enable via Terminal
    • Enable via Desktop
    • Enable via raspi-config
  • Start SSH
• Remote Log-in
  • Generate SSH Keys
    • How to Generate Keys
  • Setup Cluster Keys

Network Lookup Table

Let's enumerate each Pi and outline the network configuration for reference.

Pi Number	Interface	IP Address	Hostname
0	eth0	192.168.0.100	master
1	eth0	192.168.0.101	worker1
2	eth0	192.168.0.102	worker2
3	eth0	192.168.0.103	worker3
4	eth0	192.168.0.104	worker4

You guessed right! There is a "master" node that will oversee and control the cluster while each "worker" executes whatever command the master issued.

Assign a static IP address

To facilitate communication between the cluster, let's assign a static local IP address to each Raspberry Pi board in the network switch.

Edit file /etc/dhcpcd.conf

sudo nano /etc/dhcpcd.conf

Uncomment the following lines and add X

interface eth0
static ip_address=192.168.0.10X/24

Where X represents the Pi Number in the Network Lookup Table.

Reminder: You have to edit this file manually on each Raspberry Pi.

Change Hostname

Raspbian by default, sets the hostname of each Pi to raspberrypi. Such hostname is not mapped to the IP address given it can change via DHCP but since we assigned a static IP address we can map it. Mapping the hostname to the static IP will ease communication between the network.

Rename the hostname

By changing the hostname to master and workerX you will be able to distinguish between the nodes.

Edit file /etc/hostname and replace raspberrypi with each the Pi's hostname

sudo nano /etc/hostname

Each Pi's hostname is specified in the Network Lookup Table.

Reminder: You have to change the hostname manually on each Raspberry Pi.

Mapping the hostname

All of your Raspberry Pi's must have each of their IP addresses mapped to their hostnames in the /etc/hosts file so that each Pi can fully communicate with each other.

Edit file /etc/hosts and add the following:

# pi-cluster network
192.168.0.100    master
192.168.0.101    worker1
192.168.0.102    worker2
192.168.0.103    worker3
192.168.0.104    worker4

Reboot system for changes to take effect

shutdown -r now

Reminder: You have to do this manually on each Raspberry Pi.

Enable Secure Shell (SSH)

SSH is a network protocol for operating network services securely such as log into a remote computer, execute commands, tunneling, forwarding TCP ports and transfer files (via secure copy or scp).

We need SSH for each Pi to communicate with each other and be able to execute commands coming from the Master node.

Enable SSH

SSH is disabled by default as of latest Raspbian versions. Thus, we need to enable it but first, you must change your default password.

To change your default password, simply open a terminal window, type in passwd, press enter and follow the prompts. We suggest something easy while configuring the cluster, we will discuss Cluster Security measurements later.

Enable via Terminal

Open a terminal window and type in

sudo systemctl enable ssh

Enable via Desktop

1. Go to Preferences menu and open Raspberry Pi Configuration
2. Head over to the Interfaces tab
3. Select Enabled right next to SSH
4. Click OK
5. Start the service

Enable via raspi-config

1. Open a terminal window and type in sudo raspi-config
2. Select Interfacing Options
3. Navigate to SSH and select it
4. Choose Yes
5. Select Ok
6. Choose Finish

Start SSH

To start up the SSH service, run the following command

sudo systemctl start ssh

Remote Log-in

With the hostname mapped to each IP address on each Pi and SSH enabled, remote login becomes easier

ssh pi@worker3

If that is your first time remotely logging in to worker3, it will ask you if you trust the destination, type in yes and press enter.

The problem here is that every time you log in remotely to any other Pi, it will ask you for that Pi's password.

Generate SSH Keys

To avoid typing in the password of the computer we're trying to remotely log in to, we create what is called private and public key-pairs.

The private key is solely for the computer in which the key is being generated (not to be shared) while the public key can be shared among other computers for these to be able to securely login remotely without entering a password.

How to Generate Keys

To generate private/public keys, run this command

ssh-keygen -t ed25519

Press Enter three (3) times.

That will generate a private and public key-pair within the ~/.ssh hidden directory. The private key is stored in file ~/.ssh/id_ed25519 and the public key is in file ~/.ssh/id_ed25519.pub. DO NOT modify or share the private key file!

Setup Cluster Keys

1. Login to master node and generate keys for it

ssh-keygen -t ed25519

Press Enter three (3) times.

2. Append master's public key to its own SSH authorized keys file

cat ~/.ssh/id_ed22519.pub >> ~/.ssh/authorized_keys

3. Login to worker X node and generate keys for it

ssh-keygen -t ed25519

Press Enter three (3) times.

4. Append worker X's public key to the master's SSH authorized keys file

cat ~/.ssh/id_ed22519.pub | ssh pi@master 'cat >> ~/.ssh/authorized_keys'

Enter the master's password if prompted.

5. Repeat steps 3-4 for each worker specified in the Network Lookup Table
6. Login to master node
7. Overwrite the master's SSH authorized keys file to each worker X

scp ~/.ssh/authorized_keys pi@workerX:~/.ssh/authorized_keys

Where X represents the Pi Number in the Network Lookup Table.

7. Repeat step 6 for each worker specified in the Network Lookup Table
8. Done

You should now be able to log in remotely to any Pi on the network from any other Pi.