Skip to content

Latest commit

 

History

History
256 lines (230 loc) · 9.11 KB

CHANGES.rst

File metadata and controls

256 lines (230 loc) · 9.11 KB
Raw

Hiveeyes MicroPython Datalogger CHANGES

Development

  • Improve documentation
  • Improve voltage divider settings for reading the battery level
  • Package the release bundle with the same directory layout as the sandbox
  • Add foundation for having button events through ESP32 touch pads
  • Add basic logging configuration settings to support turning off logging entirely
  • Fix purging of sensible configuration keys
  • Improve MAC address formatting when logging network status
  • Try 11 dB attenuation for measuring vcc
  • Disable heartbeat through RGB-LED, just blink twice on startup
  • Turn off interrupts while powering down the HX711
  • Improve inline documentation and logging
  • Improve IRQ handling when reading the HX711
  • Sleep for 80 microseconds after pulling HX711 clock pin to high
  • Improve bus- and sensor power-management. Add "power_on" signal.
  • Explicitly turn off LTE modem before deep sleep

2019-06-17 0.4.0

Getting real.

  • Upgrade to Pycom MicroPython 1.20.0.rc11
  • Stop leaking sensible information into settings output
  • Improve documentation
  • Switch to LittleFS
  • Add deep sleep
  • Improve Makefile targets
  • Add more wakeup reasons
  • Add missing configuration section for HX711 to settings example. Thanks, @ClemensGruber.
  • Add basic device-interval sensors SystemTemperature and SystemBatteryLevel
  • Explicitly shut down all peripherals having implicitly been turned on
  • Add SystemWiFiMetrics sensor
  • Add SystemUptime sensor
  • Fix: Better explicitly initialize the ADC before reading it
  • Improve SystemBatteryLevel sensor. Thanks, Dominik!
  • Make TelemetryTransportHTTP work again
  • Improve telemetry subsystem re. multi-protocol and -topology. Enable HTTP telemetry.
  • Add configuration example for BEEP-BOB settings.example-bob.py
  • Honor "scale" and "offset" parameters when reading the HX711. Fix #6.
  • Improve reading the HX711 re. wrong kg scaling. Transmit all raw values and settings of HX711.
  • Attempt to improve #5: Reading Vcc.
  • Add missing "topology" configuration settings attribute for MQTT telemetry to example configurations
  • Fix deep sleep
  • Conditionally start telemetry subsystem just if networking is available
  • Improve robustness wrt. WiFi connectivity
  • Improve log messages
  • Bump version to 0.4.0dev
  • Improve purging of sensible configuration settings
  • SystemBatteryLevel: Obtain voltage divider parameters from settings
  • Improve release tooling
  • Improve error signalling for missing "topology" configuration setting

2019-06-07 0.3.0

Yaks all the way down.

  • Add ds18x20 lib
  • Implement DS and HX sensors using AbstractSensor
  • ds18x20: Add reading multiple sensors
  • Populate SensorManager, add bus management, add OneWireBus
  • SensorManager: Make ds18x20 use OneWire-Bus through AbstractBus
  • ds18x20: fix runtime issues, resetting OneWire before scanning for devices
  • Little cleanup
  • SensorManager
    • Add bus driver for i2c and onewire busses
    • Settings: add busses to (sensor-)settings
    • Convention: Bus address <BUS_FAMILY>:<BUS_NUMBER>
  • Makefile|libs:
    • Add bme280, Pycoproc, Quectel L76 GNSS library (Pytrack Board)
    • Add Pytrack Board Library, Pytrack Board Accelerator
  • SensorManager
    • Add bus to sensor registry
    • Add bme280 (humidity, temperature, pressure)
    • Add i2c bus
    • Cleanups
  • Compensate for missing _onewire package, maybe on older firmwares
  • Move acquire_bus to AbstractSensor
  • Fix I2C pin propagation
  • Add Pytrack sensor
  • Don't croak on failures
  • Fix HX711 pin wiring
  • Move Pytrack sensor to ratrack namespace
  • Add Pytrack Quectel L76 GNSS sensor
  • Makefile: cleanup (rm old DS18X20 lib)
  • settings|sensor: add TODO: "i2c-address -> settings -> sensor"
  • settings|sensor: add TODO: "i2c-address -> settings -> sensor"
  • Sensors: naming, (WIP!) hardcoded proposal for naming (see bme280)
  • Add Pytrack support
  • Moar sensors
  • Add appropriate logging
  • Improve LoRa subsystem
  • Improve logging, code cosmetics
  • Add "make clean" target
  • Enable all sensors
  • Improve bus registration
  • Improve BME280 readings
  • Improve documentation
  • Update documentation
  • Add LoRaWAN/TTN telemetry with CayenneLPP
  • Start WiFi before LoRaWAN
  • Reduce logging noise
  • Improve sandbox, documentation and naming things
  • Update documentation
  • Remove main.py.dist again
  • Improve automatic sensor field naming
  • Improve example settings
  • Improve logging all over the place
  • Upgrade to rshell 0.0.21
  • Use “device_id” as part of the MQTT “client_id”
  • Fix telemetry success signalling
  • Cleanup
  • Improve network/telemetry error handling, robustness and convenience for WiFi and MQTT connectivity
  • Improve logging
  • Update documentation
  • Improve reporting about which telemetry targets succeeded

2019-03-23 0.2.1

Fixes.

  • Fix install-requirements re. dotty_dict patching
  • Fix "make list-serials"
  • Dependencies: add OneWire & DS18x20 libraries
  • Fix urllib dep
  • Introduce SensorManager
  • Fix urllib dep

2019-03-17 0.2.0

Fill in the gaps, lots of.

  • Update documentation
  • Update backlog
  • Improve MQTT robustness by compensating ECONNRESET and ECONNABORTED exceptions from connection to MQTT broker by attempting to transparently reconnect next time when performing a telemetry submission.
  • Stop connecting to further WiFi networks after getting connected already
  • Make the telemetry domain obtain the "format" parameter from configuration settings in order to control the serialization method.
  • Update MQTT address example settings
  • Improve WiFi STA connectivity and status reporting
  • Improve status reporting and inline comments
  • Fix example configuration
  • Improve documentation
  • Preparing cayenneLPP into telemetry, new convention for sensor mapping (e.g. channel in CayenneLPP)
  • Lora works now, cleaning up and restructuring, might be good
  • Add TTN to get_handler() and transmit()
  • Improve telemetry target selector
  • Add PyCayenneLPP package to foundation libraries
  • Add telemetry target for running Base64-encoded CayenneLPP over MQTT
  • install upip via pypi
  • Add project header to main sketch files
  • Improve PyCayenneLPP installation
  • Reduce rshell buffer size to "30"
  • Improve Telemetry - Multiple telemetry sinks running in parallel - Add MQTT driver adapter
  • Streamline sensor reading vs. telemetry submission
  • Trim configuration settings output
  • Naming things
  • Improve documentation
  • Fix channel naming in example configuration
  • Skip reporting the current configuration settings as this crashes the serial output on WSL.
  • Use environment variable "MCU_SERIAL_PORT" for configuring serial port
  • Overhaul make target "setup-requirements" to populate "dist-packages"
  • Update documentation, improve README and add README-HARDWARE.md
  • Improve "refresh-requirements" make target
  • Documentation, once more
  • Bump documentation again
  • Slight application namespace refactoring
  • Improve reporting
  • Don't enable serial device in "boot.py"
  • Improve documentation
  • Add examples for different use cases
  • Build distribution archive files and upload them to GitHub
  • Refactoring/modularization
  • Update documentation
  • Minor fixes
  • Re-add BobDatalogger
  • Add release tooling

2019-03-14 0.1.0

Architecture blueprint. Works, sort of.

  • Add build environment
  • Begin with documentation
  • Large refactoring
  • Remove "urllib" package as we might want to pull it back in using "upip" later.
  • Add dependency management through "dist-packages" folder by using "upip" with MicroPython on Unix
  • Improve framework layout
  • Improve robustness of TelemetryClient
  • Add DummySensor
  • Add MemoryFree sensor
  • Update documentation
  • Add vanilla hx711.py by David Gerber
  • Add improved HX711 library by Ralf Lindlein
  • Improve documentation
  • Code cosmetics, improve logging
  • Add HX711 sensor component
  • Update documentation and tooling
  • Improve HX711 sensor robustness, don't block the device driver while waiting for hardware intercom
  • Add watchdog timer (WDT) support
  • Idle in the mainloop
  • Naming things
  • Run garbage collector on each loop iteration
  • Prepare RTC code
  • Ignore empty sensor readings
  • Naming things, HX711 robustness
  • Add vanilla "dotty_dict" package
  • Add basic TTN example
  • TTN for real?
  • Improve configuration system and WiFi STA connectivity
  • Update documentation
  • This and that
  • Troubleshooting git errors, whatever, need to commit
  • Add LoRaWAN (TTN) flavour to terking devices
  • this and that, still WIP, not working
  • WIP: code is running, but not connected to TTN successfull
  • Lora works now, cleaning up and restructuring, might be good
  • Resolve urllib dependency woes
  • Use telemetry parameters from configuration settings
  • This and that
  • Use sensor parameters from configuration settings
  • Increase number of retry attempts for catching a WiFi connection, essentially checking for 15 seconds
  • Update documentation
  • Refactor LoRaWAN bootstrapping

2019-03-01 0.0.0

Baby steps.

  • Initial commit
  • Add .gitignore to exclude *_local.py configuration files
  • WIP: Hands on FiPy
  • First stable version