/
configA.txt
146 lines (122 loc) · 3.76 KB
/
configA.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
# =====================================================================
# config.txt file for RGBtoHDMI (https://github.com/hoglet67/RGBtoHDMI)
# =====================================================================
# =====================================================================
# Default options
# =====================================================================
# Automatically overclock Pi 1 and Pi 2 to support 9/12bpp modes
# set to 0 if you experience lockups when selecting 9/12bpp modes
# doesn't affect Pi zero, Pi zero 2, Pi 3 or Pi 4
auto_overclock=1
# Boot quickly
boot_delay=0
# Disable adjusting the refresh rate of RAM every 500 ms
disable_pvt=1
# Don't allow ARM to use Level 2 Cache - this actually speeds up cache misses
disable_l2cache=1
# Enable VSYNC interrupt
fake_vsync_isr=1
# Clock frequency override to make sure we run at 1000MHz
force_turbo=1
# Stop undervolt detection from throttling the cpu
avoid_warnings=2
# Startup files, etc
kernel_address=0x1f00000
# =====================================================================
# Common video settings
# =====================================================================
# Allow framebuffer to have it's aspect ratio warped when scaling
# (needed for mode 7, 504x540 with 4/3 aspect ratio pixels)
framebuffer_aspect=-1
# Ensure default overscan values are 0 (rather than 32/48)
# Without this, the integer scaling calculation will be messed up
disable_overscan=1
# Set the maximum framebuffer height to 4*2048
# (the 4x is because we allow upto quadruple buffering)
max_framebuffer_height=8192
# Set to 1 to make hdmi use DPM standby instead of just blanking the screen
hdmi_blanking=1
# Always assume hdmi connection
# hdmi_force_hotplug=1
# Set hdmi signal strength. (Valid values are 0-11)
config_hdmi_boost=5
# =====================================================================
# Settings for Pi Models
# =====================================================================
[pi0]
# default frequencies are 1000 / 400 / 450
arm_freq=1000
core_freq=400
sdram_freq=450
start_file=start_cd.elf
fixup_file=fixup_cd.dat
kernel=kernelrpiA.img
# Debug kernel (needs a 115200 serial connection)
#kernel=kernelrpiA_debug.img
# Settings for Pi0 2
[pi02]
# default frequencies are 1000/400/450
arm_freq=1000
core_freq=400
sdram_freq=450
start_file=start_cd.elf
fixup_file=fixup_cd.dat
kernel=kernelrpiA.img
# Debug kernel (needs a 115200 serial connection)
#kernel=kernelrpiA_debug.img
[pi1]
# default frequencies are 700/250/400
arm_freq=700
core_freq=250
sdram_freq=400
start_file=start_cd.elf
fixup_file=fixup_cd.dat
kernel=kernelrpiA.img
# Debug kernel (needs a 115200 serial connection)
#kernel=kernelrpiA_debug.img
# Settings for Pi 2
[pi2]
# default frequencies are 900/250/400
arm_freq=900
core_freq=250
sdram_freq=400
start_file=start_cd.elf
fixup_file=fixup_cd.dat
kernel=kernelrpiA.img
# Debug kernel (needs a 115200 serial connection)
#kernel=kernelrpiA_debug.img
# Settings for Pi 3
[pi3]
# default frequencies are 1200/400/450
arm_freq=1000
core_freq=400
sdram_freq=450
start_file=start_cd.elf
fixup_file=fixup_cd.dat
kernel=kernelrpiA.img
# Debug kernel (needs a 115200 serial connection)
#kernel=kernelrpiA_debug.img
# Settings for Pi 3+
[pi3+]
# default frequencies are 1400/400/450
arm_freq=1000
core_freq=400
sdram_freq=450
start_file=start_cd.elf
fixup_file=fixup_cd.dat
kernel=kernelrpiA.img
# Debug kernel (needs a 115200 serial connection)
#kernel=kernelrpiA_debug.img
# Settings for Pi 4
[pi4]
# default frequencies are 1500/500/3200
arm_freq=1000
core_freq=500
sdram_freq=3200
start_file=start4cd.elf
fixup_file=fixup4cd.dat
kernel=kernelrpiA4.img
# Debug kernel (needs a 115200 serial connection)
#kernel=kernelrpiA4_debug.img
# Do not manually add options below this line as they will be removed
[all]