main.c

/**
 * Copyright (c) 2014 - 2018, Nordic Semiconductor ASA
 *
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without modification,
 * are permitted provided that the following conditions are met:
 *
 * 1. Redistributions of source code must retain the above copyright notice, this
 *    list of conditions and the following disclaimer.
 *
 * 2. Redistributions in binary form, except as embedded into a Nordic
 *    Semiconductor ASA integrated circuit in a product or a software update for
 *    such product, must reproduce the above copyright notice, this list of
 *    conditions and the following disclaimer in the documentation and/or other
 *    materials provided with the distribution.
 *
 * 3. Neither the name of Nordic Semiconductor ASA nor the names of its
 *    contributors may be used to endorse or promote products derived from this
 *    software without specific prior written permission.
 *
 * 4. This software, with or without modification, must only be used with a
 *    Nordic Semiconductor ASA integrated circuit.
 *
 * 5. Any software provided in binary form under this license must not be reverse
 *    engineered, decompiled, modified and/or disassembled.
 *
 * THIS SOFTWARE IS PROVIDED BY NORDIC SEMICONDUCTOR ASA "AS IS" AND ANY EXPRESS
 * OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
 * OF MERCHANTABILITY, NONINFRINGEMENT, AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED. IN NO EVENT SHALL NORDIC SEMICONDUCTOR ASA OR CONTRIBUTORS BE
 * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
 * GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
 * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *
 */
/** @file
 *
 * @defgroup ble_sdk_uart_over_ble_main main.c
 * @{
 * @ingroup  ble_sdk_app_nus_eval
 * @brief    UART over BLE application main file.
 *
 * This file contains the source code for a sample application that uses the Nordic UART service.
 * This application uses the @ref srvlib_conn_params module.
 */


#include <stdint.h>
#include <string.h>
#include "nordic_common.h"
#include "nrf.h"
#include "ble_hci.h"
#include "ble_advdata.h"
#include "ble_advertising.h"
#include "ble_conn_params.h"
#include "nrf_sdh.h"
#include "nrf_sdh_soc.h"
#include "nrf_sdh_ble.h"
#include "nrf_ble_gatt.h"
#include "nrf_ble_qwr.h"
#include "app_timer.h"
#include "ble_image_transfer_service.h"
#include "app_uart.h"
#include "app_util_platform.h"
#include "bsp_btn_ble.h"
#include "nrf_pwr_mgmt.h"

#if defined (UART_PRESENT)
#include "nrf_uart.h"
#endif
#if defined (UARTE_PRESENT)
#include "nrf_uarte.h"
#endif

#include "ArducamMini2MP.h"
#include "nrf_delay.h"

#include "nrf_log.h"
#include "nrf_log_ctrl.h"
#include "nrf_log_default_backends.h"

#define PCA10056_USE_FRONT_HEADER       0                                            /**< Use the front header (P24) for the camera module. Requires SB10-15 and SB20-25 to be soldered/cut, as described in the readme. */

#define FLUSH_FIRST_BYTE                0                                           /* 0 -- V2640_MINI_2MP_PLUS , 1 -- V2640_MINI_2MP*/



#define APP_BLE_CONN_CFG_TAG            1                                           /**< A tag identifying the SoftDevice BLE configuration. */

#define DEVICE_NAME                     "Camera Demo v2"                            /**< Name of device. Will be included in the advertising data. */
#define NUS_SERVICE_UUID_TYPE           BLE_UUID_TYPE_VENDOR_BEGIN                  /**< UUID type for the Nordic UART Service (vendor specific). */

#define APP_BLE_OBSERVER_PRIO           3                                           /**< Application's BLE observer priority. You shouldn't need to modify this value. */

#define APP_ADV_INTERVAL                64                                          /**< The advertising interval (in units of 0.625 ms. This value corresponds to 40 ms). */

#define APP_ADV_DURATION                18000                                       /**< The advertising duration (180 seconds) in units of 10 milliseconds. */

#define MIN_CONN_INTERVAL               MSEC_TO_UNITS(15, UNIT_1_25_MS)             /**< Minimum acceptable connection interval (20 ms), Connection interval uses 1.25 ms units. */
#define MAX_CONN_INTERVAL               MSEC_TO_UNITS(15, UNIT_1_25_MS)             /**< Maximum acceptable connection interval (75 ms), Connection interval uses 1.25 ms units. */
#define SLAVE_LATENCY                   0                                           /**< Slave latency. */
#define CONN_SUP_TIMEOUT                MSEC_TO_UNITS(4000, UNIT_10_MS)             /**< Connection supervisory timeout (4 seconds), Supervision Timeout uses 10 ms units. */
#define FIRST_CONN_PARAMS_UPDATE_DELAY  APP_TIMER_TICKS(5000)                       /**< Time from initiating event (connect or start of notification) to first time sd_ble_gap_conn_param_update is called (5 seconds). */
#define NEXT_CONN_PARAMS_UPDATE_DELAY   APP_TIMER_TICKS(30000)                      /**< Time between each call to sd_ble_gap_conn_param_update after the first call (30 seconds). */
#define MAX_CONN_PARAMS_UPDATE_COUNT    3                                           /**< Number of attempts before giving up the connection parameter negotiation. */

#define DEAD_BEEF                       0xDEADBEEF                                  /**< Value used as error code on stack dump, can be used to identify stack location on stack unwind. */

#define UART_TX_BUF_SIZE                256                                         /**< UART TX buffer size. */
#define UART_RX_BUF_SIZE                256                                         /**< UART RX buffer size. */


BLE_ITS_DEF(m_its, NRF_SDH_BLE_TOTAL_LINK_COUNT);                                   /**< BLE NUS service instance. */
NRF_BLE_GATT_DEF(m_gatt);                                                           /**< GATT module instance. */
NRF_BLE_QWR_DEF(m_qwr);                                                             /**< Context for the Queued Write module.*/
BLE_ADVERTISING_DEF(m_advertising);                                                 /**< Advertising module instance. */

static uint8_t m_new_command_received = 0;
static uint8_t m_new_resolution, m_new_phy;
static arducam_mini_2mp_init_t m_camera_init;

static bool m_stream_mode_active = false;

static ble_its_ble_params_info_t m_ble_params_info = {20, 50, 1, 1};

static uint16_t m_conn_handle          = BLE_CONN_HANDLE_INVALID;                   /**< Handle of the current connection. */
static uint16_t m_ble_its_max_data_len = BLE_GATT_ATT_MTU_DEFAULT - 3;              /**< Maximum length of data (in bytes) that can be transmitted to the peer by the Nordic UART service module. */
static ble_uuid_t m_adv_uuids[]          =                                          /**< Universally unique service identifier. */
{
        {BLE_UUID_ITS_SERVICE, NUS_SERVICE_UUID_TYPE}
};

enum {APP_CMD_NOCOMMAND = 0, APP_CMD_SINGLE_CAPTURE, APP_CMD_START_STREAM, APP_CMD_STOP_STREAM,
      APP_CMD_CHANGE_RESOLUTION, APP_CMD_CHANGE_PHY, APP_CMD_SEND_BLE_PARAMS};

/**@brief Function for assert macro callback.
 *
 * @details This function will be called in case of an assert in the SoftDevice.
 *
 * @warning This handler is an example only and does not fit a final product. You need to analyse
 *          how your product is supposed to react in case of Assert.
 * @warning On assert from the SoftDevice, the system can only recover on reset.
 *
 * @param[in] line_num    Line number of the failing ASSERT call.
 * @param[in] p_file_name File name of the failing ASSERT call.
 */
void assert_nrf_callback(uint16_t line_num, const uint8_t * p_file_name)
{
        app_error_handler(DEAD_BEEF, line_num, p_file_name);
}


/**@brief Function for initializing the timer module.
 */
static void timers_init(void)
{
        ret_code_t err_code = app_timer_init();
        APP_ERROR_CHECK(err_code);
}


/**@brief Function for the GAP initialization.
 *
 * @details This function will set up all the necessary GAP (Generic Access Profile) parameters of
 *          the device. It also sets the permissions and appearance.
 */
static void gap_params_init(void)
{
        uint32_t err_code;
        ble_gap_conn_params_t gap_conn_params;
        ble_gap_conn_sec_mode_t sec_mode;

        BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode);

        err_code = sd_ble_gap_device_name_set(&sec_mode,
                                              (const uint8_t *) DEVICE_NAME,
                                              strlen(DEVICE_NAME));
        APP_ERROR_CHECK(err_code);

        memset(&gap_conn_params, 0, sizeof(gap_conn_params));

        gap_conn_params.min_conn_interval = MIN_CONN_INTERVAL;
        gap_conn_params.max_conn_interval = MAX_CONN_INTERVAL;
        gap_conn_params.slave_latency     = SLAVE_LATENCY;
        gap_conn_params.conn_sup_timeout  = CONN_SUP_TIMEOUT;

        err_code = sd_ble_gap_ppcp_set(&gap_conn_params);
        APP_ERROR_CHECK(err_code);

#if 0
        ble_gap_addr_t ble_address = {.addr_type = BLE_GAP_ADDR_TYPE_RANDOM_STATIC,
                                      .addr_id_peer = 0,
                                      .addr = {0xC3,0x11,0x99,0x33,0x44,0xFF}};
        err_code = sd_ble_gap_addr_set(&ble_address);
        APP_ERROR_CHECK(err_code);
#endif
}


/**@brief Function for handling Queued Write Module errors.
 *
 * @details A pointer to this function will be passed to each service which may need to inform the
 *          application about an error.
 *
 * @param[in]   nrf_error   Error code containing information about what went wrong.
 */
static void nrf_qwr_error_handler(uint32_t nrf_error)
{
        APP_ERROR_HANDLER(nrf_error);
}


/**@brief Function for handling the data from the ITS Service.
 *
 * @details This function will process the data received from the ITS BLE Service.
 *
 * @param[in] p_its    ITS Service structure.
 * @param[in] p_data   Data received.
 * @param[in] length   Length of the data.
 */
/**@snippet [Handling the data received over BLE] */
static void its_data_handler(ble_its_t * p_its, uint8_t const * p_data, uint16_t length)
{
        switch(p_data[0])
        {
        // Take picture
        case APP_CMD_SINGLE_CAPTURE:
        case APP_CMD_SEND_BLE_PARAMS:
                m_new_command_received = p_data[0];
                break;

        case APP_CMD_START_STREAM:
                m_stream_mode_active = true;
                m_new_command_received = p_data[0];
                break;

        case APP_CMD_STOP_STREAM:
                m_stream_mode_active = false;
                m_new_command_received = p_data[0];
                break;

        case APP_CMD_CHANGE_RESOLUTION:
                m_new_command_received = APP_CMD_CHANGE_RESOLUTION;
                m_new_resolution = p_data[1];
                break;

        case APP_CMD_CHANGE_PHY:
                m_new_command_received = APP_CMD_CHANGE_PHY;
                m_new_phy = p_data[1];
                break;

        default:
                NRF_LOG_ERROR("Unknown command!!");
                break;
        }
}
/**@snippet [Handling the data received over BLE] */


/**@brief Function for initializing services that will be used by the application.
 */
static void services_init(void)
{
        uint32_t err_code;
        ble_its_init_t its_init;
        nrf_ble_qwr_init_t qwr_init = {0};

        // Initialize Queued Write Module.
        qwr_init.error_handler = nrf_qwr_error_handler;

        err_code = nrf_ble_qwr_init(&m_qwr, &qwr_init);
        APP_ERROR_CHECK(err_code);

        // Initialize ITS.
        memset(&its_init, 0, sizeof(its_init));

        its_init.data_handler = its_data_handler;

        err_code = ble_its_init(&m_its, &its_init);
        APP_ERROR_CHECK(err_code);
}


/**@brief Function for handling an event from the Connection Parameters Module.
 *
 * @details This function will be called for all events in the Connection Parameters Module
 *          which are passed to the application.
 *
 * @note All this function does is to disconnect. This could have been done by simply setting
 *       the disconnect_on_fail config parameter, but instead we use the event handler
 *       mechanism to demonstrate its use.
 *
 * @param[in] p_evt  Event received from the Connection Parameters Module.
 */
static void on_conn_params_evt(ble_conn_params_evt_t * p_evt)
{
        switch(p_evt->evt_type)
        {
        case BLE_CONN_PARAMS_EVT_SUCCEEDED:
                break;

        case BLE_CONN_PARAMS_EVT_FAILED:
                //err_code = sd_ble_gap_disconnect(m_conn_handle, BLE_HCI_CONN_INTERVAL_UNACCEPTABLE);
                //APP_ERROR_CHECK(err_code);
                NRF_LOG_ERROR("Conn params failed. Keep the connection anyway..");
                break;
        }
}


/**@brief Function for handling errors from the Connection Parameters module.
 *
 * @param[in] nrf_error  Error code containing information about what went wrong.
 */
static void conn_params_error_handler(uint32_t nrf_error)
{
        APP_ERROR_HANDLER(nrf_error);
}


/**@brief Function for initializing the Connection Parameters module.
 */
static void conn_params_init(void)
{
        uint32_t err_code;
        ble_conn_params_init_t cp_init;

        memset(&cp_init, 0, sizeof(cp_init));

        cp_init.p_conn_params                  = NULL;
        cp_init.first_conn_params_update_delay = FIRST_CONN_PARAMS_UPDATE_DELAY;
        cp_init.next_conn_params_update_delay  = NEXT_CONN_PARAMS_UPDATE_DELAY;
        cp_init.max_conn_params_update_count   = MAX_CONN_PARAMS_UPDATE_COUNT;
        cp_init.start_on_notify_cccd_handle    = BLE_GATT_HANDLE_INVALID;
        cp_init.disconnect_on_fail             = false;
        cp_init.evt_handler                    = on_conn_params_evt;
        cp_init.error_handler                  = conn_params_error_handler;

        err_code = ble_conn_params_init(&cp_init);
        APP_ERROR_CHECK(err_code);
}



/**@brief Function for handling advertising events.
 *
 * @details This function will be called for advertising events which are passed to the application.
 *
 * @param[in] ble_adv_evt  Advertising event.
 */
static void on_adv_evt(ble_adv_evt_t ble_adv_evt)
{
        uint32_t err_code;

        switch (ble_adv_evt)
        {
        case BLE_ADV_EVT_FAST:
                err_code = bsp_indication_set(BSP_INDICATE_ADVERTISING);
                APP_ERROR_CHECK(err_code);
                break;
        case BLE_ADV_EVT_IDLE:
                NRF_LOG_INFO("BLE_ADV_EVT_IDLE...");
                err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST);
                APP_ERROR_CHECK(err_code);
                break;
        default:
                break;
        }
}


/**@brief Function for handling BLE events.
 *
 * @param[in]   p_ble_evt   Bluetooth stack event.
 * @param[in]   p_context   Unused.
 */
static void ble_evt_handler(ble_evt_t const * p_ble_evt, void * p_context)
{
        uint32_t err_code;

        switch (p_ble_evt->header.evt_id)
        {
        case BLE_GAP_EVT_CONNECTED:
                NRF_LOG_INFO("Connected");
                err_code = bsp_indication_set(BSP_INDICATE_CONNECTED);
                APP_ERROR_CHECK(err_code);
                m_conn_handle = p_ble_evt->evt.gap_evt.conn_handle;
                err_code = nrf_ble_qwr_conn_handle_assign(&m_qwr, m_conn_handle);
                APP_ERROR_CHECK(err_code);
                ble_its_ble_params_info_send(&m_its, &m_ble_params_info);
                break;

        case BLE_GAP_EVT_DISCONNECTED:
                NRF_LOG_INFO("Disconnected");
                // LED indication will be changed when advertising starts.
                m_stream_mode_active = false;
                m_new_command_received = APP_CMD_CHANGE_RESOLUTION;
                m_new_resolution = 1;
                m_conn_handle = BLE_CONN_HANDLE_INVALID;
                break;

        case BLE_GAP_EVT_CONN_PARAM_UPDATE:
        {
                uint16_t max_con_int = p_ble_evt->evt.gap_evt.params.conn_param_update.conn_params.max_conn_interval;
                uint16_t min_con_int = p_ble_evt->evt.gap_evt.params.conn_param_update.conn_params.min_conn_interval;

                m_ble_params_info.con_interval = max_con_int;
                ble_its_ble_params_info_send(&m_its, &m_ble_params_info);
                NRF_LOG_INFO("Con params updated: CI %i, %i", (int)min_con_int, (int)max_con_int);
        } break;

        case BLE_GAP_EVT_PHY_UPDATE_REQUEST:
        {
                NRF_LOG_DEBUG("PHY update request.");
                ble_gap_phys_t const phys =
                {
                        BLE_GAP_PHY_AUTO,
                        BLE_GAP_PHY_AUTO,
                };
                err_code = sd_ble_gap_phy_update(p_ble_evt->evt.gap_evt.conn_handle, &phys);
                APP_ERROR_CHECK(err_code);
        } break;

        case BLE_GAP_EVT_PHY_UPDATE:
                m_ble_params_info.tx_phy = p_ble_evt->evt.gap_evt.params.phy_update.tx_phy;
                m_ble_params_info.rx_phy = p_ble_evt->evt.gap_evt.params.phy_update.rx_phy;
                ble_its_ble_params_info_send(&m_its, &m_ble_params_info);
                NRF_LOG_INFO("Phy update: %i, %i", (int)m_ble_params_info.tx_phy, (int)m_ble_params_info.rx_phy);
                break;

        case BLE_GAP_EVT_SEC_PARAMS_REQUEST:
                // Pairing not supported
                err_code = sd_ble_gap_sec_params_reply(m_conn_handle, BLE_GAP_SEC_STATUS_PAIRING_NOT_SUPP, NULL, NULL);
                APP_ERROR_CHECK(err_code);
                break;

        case BLE_GATTS_EVT_SYS_ATTR_MISSING:
                // No system attributes have been stored.
                err_code = sd_ble_gatts_sys_attr_set(m_conn_handle, NULL, 0, 0);
                APP_ERROR_CHECK(err_code);
                break;

        case BLE_GATTC_EVT_TIMEOUT:
                // Disconnect on GATT Client timeout event.
                err_code = sd_ble_gap_disconnect(p_ble_evt->evt.gattc_evt.conn_handle,
                                                 BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION);
                APP_ERROR_CHECK(err_code);
                break;

        case BLE_GATTS_EVT_TIMEOUT:
                // Disconnect on GATT Server timeout event.
                err_code = sd_ble_gap_disconnect(p_ble_evt->evt.gatts_evt.conn_handle,
                                                 BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION);
                APP_ERROR_CHECK(err_code);
                break;

        default:
                // No implementation needed.
                //NRF_LOG_INFO("BLE event not handled by app: %i", p_ble_evt->header.evt_id);
                break;
        }
}


/**@brief Function for the SoftDevice initialization.
 *
 * @details This function initializes the SoftDevice and the BLE event interrupt.
 */
static void ble_stack_init(void)
{
        ret_code_t err_code;

        err_code = nrf_sdh_enable_request();
        APP_ERROR_CHECK(err_code);

        // Configure the BLE stack using the default settings.
        // Fetch the start address of the application RAM.
        uint32_t ram_start = 0;
        err_code = nrf_sdh_ble_default_cfg_set(APP_BLE_CONN_CFG_TAG, &ram_start);
        APP_ERROR_CHECK(err_code);

        // Enable BLE stack.
        err_code = nrf_sdh_ble_enable(&ram_start);
        APP_ERROR_CHECK(err_code);

        // Register a handler for BLE events.
        NRF_SDH_BLE_OBSERVER(m_ble_observer, APP_BLE_OBSERVER_PRIO, ble_evt_handler, NULL);
}


/**@brief Function for handling events from the GATT library. */
void gatt_evt_handler(nrf_ble_gatt_t * p_gatt, nrf_ble_gatt_evt_t const * p_evt)
{
        uint32_t data_length;
        if ((m_conn_handle == p_evt->conn_handle) && (p_evt->evt_id == NRF_BLE_GATT_EVT_ATT_MTU_UPDATED))
        {
                data_length = p_evt->params.att_mtu_effective - OPCODE_LENGTH - HANDLE_LENGTH;
                //m_ble_params_info.mtu = m_ble_its_max_data_len;

                NRF_LOG_INFO("gatt_event: ATT MTU is set to 0x%X (%d)", data_length, data_length);
        }
        else if ((m_conn_handle == p_evt->conn_handle) && (p_evt->evt_id == NRF_BLE_GATT_EVT_DATA_LENGTH_UPDATED))
        {
                data_length = p_evt->params.att_mtu_effective - OPCODE_LENGTH - HANDLE_LENGTH - 4;
                m_ble_its_max_data_len = data_length;
                m_ble_params_info.mtu = m_ble_its_max_data_len;
                ble_its_ble_params_info_send(&m_its, &m_ble_params_info);

                NRF_LOG_INFO("gatt_event: Data len is set to 0x%X (%d)", data_length, data_length);
        }
        //NRF_LOG_DEBUG("ATT MTU exchange completed. central 0x%x peripheral 0x%x",
        //            p_gatt->att_mtu_desired_central,
        //        p_gatt->att_mtu_desired_periph);
}


/**@brief Function for initializing the GATT library. */
void gatt_init(void)
{
        ret_code_t err_code;

        err_code = nrf_ble_gatt_init(&m_gatt, gatt_evt_handler);
        APP_ERROR_CHECK(err_code);

        err_code = nrf_ble_gatt_att_mtu_periph_set(&m_gatt, NRF_SDH_BLE_GATT_MAX_MTU_SIZE);
        APP_ERROR_CHECK(err_code);

        err_code = nrf_ble_gatt_data_length_set(&m_gatt, BLE_CONN_HANDLE_INVALID, NRF_SDH_BLE_GAP_DATA_LENGTH);
        APP_ERROR_CHECK(err_code);
}


/**@brief Function for handling events from the BSP module.
 *
 * @param[in]   event   Event generated by button press.
 */
void bsp_event_handler(bsp_event_t event)
{
        uint32_t err_code;
        switch (event)
        {
        case BSP_EVENT_SLEEP:
                break;

        case BSP_EVENT_DISCONNECT:
                err_code = sd_ble_gap_disconnect(m_conn_handle, BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION);
                if (err_code != NRF_ERROR_INVALID_STATE)
                {
                        APP_ERROR_CHECK(err_code);
                }
                break;

        case BSP_EVENT_WHITELIST_OFF:
                if (m_conn_handle == BLE_CONN_HANDLE_INVALID)
                {
                        err_code = ble_advertising_restart_without_whitelist(&m_advertising);
                        if (err_code != NRF_ERROR_INVALID_STATE)
                        {
                                APP_ERROR_CHECK(err_code);
                        }
                }
                break;

        default:
                break;
        }
}


/**@brief   Function for handling app_uart events.
 *
 * @details This function will receive a single character from the app_uart module and append it to
 *          a string. The string will be be sent over BLE when the last character received was a
 *          'new line' '\n' (hex 0x0A) or if the string has reached the maximum data length.
 */
/**@snippet [Handling the data received over UART] */
void uart_event_handle(app_uart_evt_t * p_event)
{

}
/**@snippet [Handling the data received over UART] */


/**@brief  Function for initializing the UART module.
 */
/**@snippet [UART Initialization] */
static void uart_init(void)
{
        uint32_t err_code;
        app_uart_comm_params_t const comm_params =
        {
                RX_PIN_NUMBER,
                TX_PIN_NUMBER,
                RTS_PIN_NUMBER,
                CTS_PIN_NUMBER,
                APP_UART_FLOW_CONTROL_DISABLED,
                false,
#if defined (UART_PRESENT)
                NRF_UART_BAUDRATE_115200
#else
                NRF_UARTE_BAUDRATE_115200
#endif
        };

        APP_UART_FIFO_INIT(&comm_params,
                           UART_RX_BUF_SIZE,
                           UART_TX_BUF_SIZE,
                           uart_event_handle,
                           APP_IRQ_PRIORITY_LOWEST,
                           err_code);
        APP_ERROR_CHECK(err_code);
}
/**@snippet [UART Initialization] */


/**@brief Function for initializing the Advertising functionality.
 */
static void advertising_init(void)
{
        uint32_t err_code;
        ble_advertising_init_t init;

        memset(&init, 0, sizeof(init));

        init.advdata.name_type          = BLE_ADVDATA_FULL_NAME;
        init.advdata.include_appearance = false;
        init.advdata.flags              = BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE;

        init.srdata.uuids_complete.uuid_cnt = sizeof(m_adv_uuids) / sizeof(m_adv_uuids[0]);
        init.srdata.uuids_complete.p_uuids  = m_adv_uuids;

        init.config.ble_adv_fast_enabled  = true;
        init.config.ble_adv_fast_interval = APP_ADV_INTERVAL;
        init.config.ble_adv_fast_timeout  = APP_ADV_DURATION;
        init.evt_handler = on_adv_evt;

        err_code = ble_advertising_init(&m_advertising, &init);
        APP_ERROR_CHECK(err_code);

        ble_advertising_conn_cfg_tag_set(&m_advertising, APP_BLE_CONN_CFG_TAG);
}


/**@brief Function for initializing buttons and leds.
 *
 * @param[out] p_erase_bonds  Will be true if the clear bonding button was pressed to wake the application up.
 */
static void buttons_leds_init(void)
{
        bsp_event_t startup_event;

        uint32_t err_code = bsp_init(BSP_INIT_LEDS | BSP_INIT_BUTTONS, bsp_event_handler);
        APP_ERROR_CHECK(err_code);

        err_code = bsp_btn_ble_init(NULL, &startup_event);
        APP_ERROR_CHECK(err_code);
}


static void camera_init(void)
{
#if defined(BOARD_PCA10056)
  #if (PCA10056_USE_FRONT_HEADER == 1)
        m_camera_init.pinScl = 13;
        m_camera_init.pinSda = 15;
        m_camera_init.pinSck = 21;
        m_camera_init.pinMiso = 23;
        m_camera_init.pinMosi = 25;
        m_camera_init.pinCsn = 32 + 9;
  #else
        m_camera_init.pinScl = 27;
        m_camera_init.pinSda = 26;
        m_camera_init.pinSck = 32 + 15;
        m_camera_init.pinMiso = 32 + 14;
        m_camera_init.pinMosi = 32 + 13;
        m_camera_init.pinCsn = 32 + 12;
  #endif
#elif defined(BOARD_PCA10040)
        m_camera_init.pinScl = 27;
        m_camera_init.pinSda = 26;
        m_camera_init.pinSck = 25;
        m_camera_init.pinMiso = 24;
        m_camera_init.pinMosi = 23;
        m_camera_init.pinCsn = 22;
#else
#error Board not defined or not supported
#endif
        arducam_mini_2mp_open(&m_camera_init);
        arducam_mini_2mp_setResolution(OV2640_320x240);
}


/**@brief Function for initializing the nrf log module.
 */
static void log_init(void)
{
        ret_code_t err_code = NRF_LOG_INIT(NULL);
        APP_ERROR_CHECK(err_code);

        NRF_LOG_DEFAULT_BACKENDS_INIT();
}


/**@brief Function for handling the idle state (main loop).
 *
 * @details If there is no pending log operation, then sleep until next the next event occurs.
 */
static void idle_state_handle(void)
{
        while(NRF_LOG_PROCESS());
        sd_app_evt_wait();
}


/**@brief Function for starting advertising.
 */
static void advertising_start(void)
{
        uint32_t err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST);
        APP_ERROR_CHECK(err_code);
}


void conn_evt_len_ext_set(bool status)
{
        ret_code_t err_code;
        ble_opt_t opt;

        memset(&opt, 0x00, sizeof(opt));
        opt.common_opt.conn_evt_ext.enable = status ? 1 : 0;

        err_code = sd_ble_opt_set(BLE_COMMON_OPT_CONN_EVT_EXT, &opt);
        APP_ERROR_CHECK(err_code);
}

void data_len_set(uint8_t value)
{
        ret_code_t err_code;
        err_code = nrf_ble_gatt_data_length_set(&m_gatt, BLE_CONN_HANDLE_INVALID, value);
        APP_ERROR_CHECK(err_code);

}


/**@brief Application main function.
 */
int main(void)
{
        uint32_t img_data_length = 0;
        uint8_t img_data_buffer[255];

        // Initialize.
        uart_init();
        log_init();
        timers_init();
        buttons_leds_init();
        ble_stack_init();
        gap_params_init();
        gatt_init();
        services_init();
        advertising_init();
        conn_params_init();
        sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE);

        // Start execution.
        NRF_LOG_INFO("Debug logging for UART over RTT started.");

        camera_init();

        advertising_start();

        // Enter main loop.
        for (;;)
        {
                uint32_t image_size;
                ble_gap_phys_t gap_phys_settings;

                if(m_new_command_received != APP_CMD_NOCOMMAND)
                {
                        uint32_t new_command = m_new_command_received;
                        m_new_command_received = APP_CMD_NOCOMMAND;
                        switch(new_command)
                        {
                        case APP_CMD_SINGLE_CAPTURE:
                                if(arducam_mini_2mp_bytesAvailable() == 0)
                                {
                                        NRF_LOG_INFO("Starting capture...");
                                        arducam_mini_2mp_startSingleCapture();
                                        image_size = arducam_mini_2mp_bytesAvailable();
                                        NRF_LOG_INFO("Capture complete: size %i bytes", (int)(image_size));
                                        ble_its_img_info_t image_info;
#if (FLUSH_FIRST_BYTE == 1)
                                        image_info.file_size_bytes = image_size - 1;
                                        ble_its_img_info_send(&m_its, &image_info);
                                        // Flush the first byte (or the JPG image will be corrupted)
                                        arducam_mini_2mp_fillBuffer(img_data_buffer, 1);
#else
                                        image_info.file_size_bytes = image_size;
                                        ble_its_img_info_send(&m_its, &image_info);
#endif

                                }
                                break;

                        case APP_CMD_START_STREAM:
                                NRF_LOG_INFO("Stream mode enabled");
                                break;

                        case APP_CMD_STOP_STREAM:
                                NRF_LOG_INFO("Stream mode disabled");
                                break;

                        case APP_CMD_CHANGE_RESOLUTION:
                                NRF_LOG_INFO("Change resolution to mode: %i", (int)m_new_resolution);
                                switch(m_new_resolution)
                                {
                                case 0:
                                        arducam_mini_2mp_setResolution(OV2640_160x120);
                                        break;

                                case 1:
                                        arducam_mini_2mp_setResolution(OV2640_320x240);
                                        break;

                                case 2:
                                        arducam_mini_2mp_setResolution(OV2640_640x480);
                                        break;

                                case 3:
                                        arducam_mini_2mp_setResolution(OV2640_800x600);
                                        break;

                                case 4:
                                        arducam_mini_2mp_setResolution(OV2640_1024x768);
                                        break;

                                case 5:
                                        arducam_mini_2mp_setResolution(OV2640_1600x1200);
                                        break;

                                }
                                break;

                        case APP_CMD_CHANGE_PHY:
                                NRF_LOG_INFO("Attempting to change phy.");
                                gap_phys_settings.tx_phys = (m_new_phy == 0 ? BLE_GAP_PHY_1MBPS : BLE_GAP_PHY_2MBPS);
                                gap_phys_settings.rx_phys = (m_new_phy == 0 ? BLE_GAP_PHY_1MBPS : BLE_GAP_PHY_2MBPS);

                                sd_ble_gap_phy_update(m_its.conn_handle, &gap_phys_settings);
                                break;

                        case APP_CMD_SEND_BLE_PARAMS:
                                ble_its_ble_params_info_send(&m_its, &m_ble_params_info);
                                break;

                        default:
                                break;
                        }
                }

                if(m_stream_mode_active)
                {
                        if(img_data_length == 0 && arducam_mini_2mp_bytesAvailable() == 0)
                        {
                                arducam_mini_2mp_startSingleCapture();

                                image_size = arducam_mini_2mp_bytesAvailable();

                                ble_its_img_info_t image_info;
#if (FLUSH_FIRST_BYTE == 1)
                                image_info.file_size_bytes = image_size - 1;
                                ble_its_img_info_send(&m_its, &image_info);

                                // Flush the first byte (or the JPG image will be corrupted)
                                arducam_mini_2mp_fillBuffer(img_data_buffer, 1);
#else
                                image_info.file_size_bytes = image_size;
                                ble_its_img_info_send(&m_its, &image_info);
#endif


                        }
                }

                if(img_data_length > 0 || arducam_mini_2mp_bytesAvailable() > 0)
                {
                        uint32_t ret_code;
                        do
                        {
                                if(img_data_length == 0)
                                {
                                        img_data_length = arducam_mini_2mp_fillBuffer(img_data_buffer, m_ble_its_max_data_len);
                                }
                                ret_code = ble_its_send_file_fragment(&m_its, img_data_buffer, img_data_length);
                                if(ret_code == NRF_SUCCESS)
                                {
                                        img_data_length = 0;
                                }
                        } while(ret_code == NRF_SUCCESS);
                }

                if(m_new_command_received == APP_CMD_NOCOMMAND)
                {
                        idle_state_handle();
                }
        }
}


/**
 * @}
 */