Replies: 10 comments 7 replies
-
|
Can you set the log level to DEBUG and send the extended log file? |
Beta Was this translation helpful? Give feedback.
-
|
It might be related to the recent changes to the Alignment Mode. That one is no longer possible during setup mode. I am juts now working on a fix. |
Beta Was this translation helpful? Give feedback.
-
|
The first error we see is Can you please try an older version (15.1.0)? If you have the same issue there -> It is most likely a hardware issue |
Beta Was this translation helpful? Give feedback.
-
How do I set that manually? I tried to do it from the server but it crashes before I can do anything |
Beta Was this translation helpful? Give feedback.
-
|
You need to flash it manually, see https://jomjol.github.io/AI-on-the-edge-device-docs/Installation/#manual-flashing Or wait a bit until we have a new release. Then you can try it again with the web installer. |
Beta Was this translation helpful? Give feedback.
-
|
New release is up (15.2.2), please try it. |
Beta Was this translation helpful? Give feedback.
-
|
ok still not working on the new update, so i assume its a hardware issue. I will try a new SD card and see if that helps |
Beta Was this translation helpful? Give feedback.
-
|
Did you check the camera is supported and attached properly? |
Beta Was this translation helpful? Give feedback.
-
|
Had the same issue.... I was on 5.2.1... was working since weeks than issue appears. I erased SD card and updated to 5.1.4 You have to disable autoboot Otherwise when it Comes to make pic it will reset |
Beta Was this translation helpful? Give feedback.
-
|
Hello all It seems I got this exact same issue yesterday morning. It was working fine until 08:00 something. Then it just gives me Initializing (delayed). Logs show: [MAIN] Camera framebuffer check failed It's been working stable since Jan up until yesterday. Firmware version was 15.1.1 and I tried to update to the latest (15.2.2) but still the same error. Cam module is supported and has been working great for about 8 months or so, since I first set this little guy up. Any ideas? Could it be the ESP32module, the camera suddenly not working, the SD-card? |
Beta Was this translation helpful? Give feedback.
-
|
They recommend 4GB, but it depends... |
Beta Was this translation helpful? Give feedback.
-
|
Tried updating to 15.2.4 today, and got exactly the same error you got. [MAIN] Camera framebuffer check failed Reverted back to my previously installed 15.1.0 and camera works again. So there is definitively no hardware issue on my end. |
Beta Was this translation helpful? Give feedback.
-
|
Interesting 🤔 Looks like I had a similar problem ~1.5 week ago for the first time (running 15.2.1). I didn't give it much thought, I didn't check any logs or anything, I just powered it off a bit and powered it on again, and it started working after some 15-30 minutes. Checking the logs now I see it was in a reboot loop with these same Four days ago, it stopped reporting data again. Only then I noticed it was in a reboot loop and found others with the same problem. This time, no amount of powering it off and on again solved it. I also updated it to 15.2.4 (no luck). I was about to try to recreate the SD card partition etc, but before that I just ran |
Beta Was this translation helpful? Give feedback.
-
|
so your sd card file system got corrupted. hopefully #2517 will improve the throubleshooting. |
Beta Was this translation helpful? Give feedback.
-
|
Maybe yes. Logging to the SD card still worked fine. So it was not entirely corrupt, but maybe enough to fail writing the captured image to it. |
Beta Was this translation helpful? Give feedback.
-
The Problem
I'm trying to an initial setup and am getting stuck in a bootloop. Below is the logfile. I have looked through other closed issues, but can't find anything with a similar log file
`
Version
v15.2.1
Logfile
Expected Behavior
No response
Screenshots
No response
Additional Context
No response
Beta Was this translation helpful? Give feedback.
All reactions