Ender3 V2/S1 Professional Firmware 20221002 #407
Replies: 27 comments 82 replies
-
|
Even though I have my printer for a very short time and the firmwares that I have tested and installed, this is the best, with the biggest and best features and possibilities of use. Greetings from Brazil |
Beta Was this translation helpful? Give feedback.
-
|
Thank you! |
Beta Was this translation helpful? Give feedback.
-
|
Hi mrisco |
Beta Was this translation helpful? Give feedback.
-
|
It will work if you set the serial port speed to 115k baud in Advanced Settings. |
Beta Was this translation helpful? Give feedback.
-
|
will do thank you. |
Beta Was this translation helpful? Give feedback.
-
|
The best just keeps getting better. Thank you so much for the hard work you put into this! This new update is silky smooth. Very happy with it. |
Beta Was this translation helpful? Give feedback.
-
|
Thanks! |
Beta Was this translation helpful? Give feedback.
-
|
Thank you for your work. |
Beta Was this translation helpful? Give feedback.
-
|
Yes, but to make space some other features were disabled:
|
Beta Was this translation helpful? Give feedback.
-
|
Is there a specific reason why G26 is not activated? I think that is very useful. |
Beta Was this translation helpful? Give feedback.
-
|
i thought the same thing. Why is G26 not activated? its pretty good actually |
Beta Was this translation helpful? Give feedback.
-
|
Is this also for the Ender 3 S1 Pro? |
Beta Was this translation helpful? Give feedback.
-
|
I bricked my printer... so i want to try this firmware. I cannot fix my firmware :/ |
Beta Was this translation helpful? Give feedback.
-
|
Yes you can use it with the Ender S1 Pro :-)But you must change your Display ;-) I have the Touch Screen changed to the Screen of the Ender 3 V2 ! Use the T13 Version : https://github.com/mriscoc/Special_Configurations/releases/tag/T13 |
Beta Was this translation helpful? Give feedback.
-
|
Thank you for the good Work 👍 Now i can level my Printer 🥇 The only Thing it is possible to set the Temp of the HotBed to 110 Grad ? |
Beta Was this translation helpful? Give feedback.
-
|
Can you post a official link where confirms 110 °C support for your printer? |
Beta Was this translation helpful? Give feedback.
-
|
The lower third of the page contains the technical data and the 110 degrees hotbed temperature for the Ender S1 Pro is normal for the Ender S1 it is 100 degrees. Greetings and keep up your great work https://store.creality.com/de/products/ender-3-s1-pro-3d-printer?spm=..page_2466949.header_1.1 |
Beta Was this translation helpful? Give feedback.
-
|
Thank you very much for letting F4 S1 use UBL, but there are several questions: What are the functions of media update and tilt mesh? Blessings from Hong Kong, China |
Beta Was this translation helpful? Give feedback.
-
|
Media update is for re-reading the filesystem each time that you enter in the media menu, useful for people with SD card extenders. |
Beta Was this translation helpful? Give feedback.
-
|
I was able to update once my printer, with the default firmware generated, but when I wanted to personalize it, to reduce the noise in the curves, it loks like it don't want to take it into account. Of course, I paid attention to the names used. Have you an idea of what could be wrong ? Maybe you can check the adaptative step smoothing settings and provide a new firmware ? |
Beta Was this translation helpful? Give feedback.
-
|
and in any case I can't upgrade the printer anymore ... |
Beta Was this translation helpful? Give feedback.
-
|
Be careful with your own compiles, the F4 bootloader is known to be a bit flawed. |
Beta Was this translation helpful? Give feedback.
-
|
Yes I noticed the bed suddenly warmed up. Do you think you can help me providing a new version - with lower Steppers speed and max temperature up to 300 - please 🤓🥹, or is too much asked ?🙏🏼 i have E3s1pro with f1 chip gracias |
Beta Was this translation helpful? Give feedback.
-
|
You can lower the speed in Control/Motion menu. I recommend to put your customization in an configuration file and load it after flashing the printer https://github.com/mriscoc/Ender3V2S1/wiki/Configuration-files |
Beta Was this translation helpful? Give feedback.
-
|
Thank you for your fast reply, I’ll try it, I hope I’ll not make any mistakes. I’m noob on this 😪😓 |
Beta Was this translation helpful? Give feedback.
-
|
Any chance of adding EZABL as an option for bed leveling in the firmware? I just bought a EZABL pro for my E3V2 |
Beta Was this translation helpful? Give feedback.
-
|
https://github.com/mriscoc/Special_Configurations/releases/tag/EZABL |
Beta Was this translation helpful? Give feedback.
-
|
Hi. Would you be able to make version for Ender 3 S1 PLUS with F4 chip please? Both UBL and nonUBL versions if possible. Thanks in advance ps: Perhaps if you could just upload conf.h and conf adv.h i could compile it myself. I tried to do it from the source files but dont really know what options to choose.... |
Beta Was this translation helpful? Give feedback.
-
|
the Wiki is your friend https://github.com/mriscoc/Ender3V2S1/wiki/Calibration-Guides |
Beta Was this translation helpful? Give feedback.
-
|
Haay MRIscoc |
Beta Was this translation helpful? Give feedback.
-
|
To return to a more silent operation you can limit the printer speed to the original stock values with:
Or using the G-codes: M203 X300.00 Y300.00 Z5.00 E25.00 ;Setup machine max feedrate
M201 X500.00 Y500.00 Z100.00 E1000.00 ;Setup machine max acceleration |
Beta Was this translation helpful? Give feedback.
-
|
thank you so much |
Beta Was this translation helpful? Give feedback.
-
|
Where are they setup (for compiling my own firmware)? Can´t find them in Configuration.h or Configuration_adv.h. Am i blind? |
Beta Was this translation helpful? Give feedback.
-
|
I am probably missing something here. I have an Ender3V2 with a Sprite Pro hotend and a 427 board. Installing the experimental firmware results in the stepper motors not moving, although it heats the hot end to 300 degrees. |
Beta Was this translation helpful? Give feedback.
-
|
If the motors are not moving that could be a problem with the firmware version that your downloaded, be sure to get the 427 version if you really have a 4.2.7 board. |
Beta Was this translation helpful? Give feedback.
-
|
Hello, I'm uncertain if I'm doing something wrong... But I seem to have trouble flashing the firmware off the root of the mSD card. I have no issues flashing with official creality firmware or an old 2.0.x bugfix firmware, but I wanted to try your firmware to use with the sprite extruder. Whenever I flash using your firmware, the screen remains blank. Any idea what I could be doing wrong? I have a 4.2.7 silent board installed on a regular Ender 3. Or as an alternative, do you know what the default CRTouch offsets are, and how I would go about setting that using a gcode command? I don't seem to have much luck compiling my own firmware either. |
Beta Was this translation helpful? Give feedback.
-
Beta Was this translation helpful? Give feedback.
-
|
Check what SoC your 4.2.7 control board has; the firmware is officially compatible with STM ones. |
Beta Was this translation helpful? Give feedback.
-
|
That's why I'm confused. The SoC is STM32F103 so it SHOULD work. I've tried following the steps from that link as well and the screen still remains blank. Would it be possible that the screen is causing issues? (This is an old Ender 3 and not a V2. It has the default 12864 OEM LCD Screen) |
Beta Was this translation helpful? Give feedback.
-
|
This firmware is only compatible with a DWIN or DACAI screen: https://github.com/mriscoc/Ender3V2S1/wiki#requirements |
Beta Was this translation helpful? Give feedback.
-
|
Ah. I didn't see the last part about legacy monochrome screens not being supported. Thank you for the help. I will try again once I have upgraded the screen |
Beta Was this translation helpful? Give feedback.
-
|
Hi, |
Beta Was this translation helpful? Give feedback.
-
|
Screen glitches can occur due to EMI in the screen cable or because forgotten to disable the +V in a USB cable. |
Beta Was this translation helpful? Give feedback.
-
|
The printer is not connected with a USB cable. It reads data from the SD card. |
Beta Was this translation helpful? Give feedback.
-
|
I've had only one strange thing happen on me, I'm running Octoprint, but as soon as I went to tune menu, it came back to standard menu. I'm running 2 systems with 4.2.2 and 4.2.7 boards. I make sure my screen cable is not wrapped with other cables as it heads out to the screen, you can get EMI interference in that thin ribbon cable. Other than seeing this only once, I've never seen again since. |
Beta Was this translation helpful? Give feedback.
-
|
I tried using Ender3V2-422-BLTUBL-20221002.bin firmware and the error does not appear with it. |
Beta Was this translation helpful? Give feedback.
-
|
This may be a stupid comment but I'm new to this firmware and I can't find much info on the thing I'm having issue with, if I run the G29 command, once it's finished auto levelling, dialogue pops up to save or continue, which should I hit, if any, or does it not matter? If I hit nothing that screen just stays on indefinitely and I cannot access any of the tuning, pausing etc |
Beta Was this translation helpful? Give feedback.
-
|
This is my Code that I use on my Ender 3 V2 in Cura Using the UBL Version Firmware. M104 S160 ; Start warming extruder to 160 G1 X0.1 Y20 Z3.0 F5000.0 ; move to start-line position |
Beta Was this translation helpful? Give feedback.
-
|
I know this works, I run a 9x9 gride and have a 2ft 3in Chinese Flexi Dragon going all around the bed, and from first layer to 3mm you will see numbers going crazy up and down in bottom display and I Print PETG Rainbow Silk, my first layer on TPI Flex Steel is as smooth as glass. |
Beta Was this translation helpful? Give feedback.
-
|
You are an absolute lifesaver my friend, thank you so much this is perfect! I really appreciate you sharing your knowledge with me, I'll give it a whirl when I'm near my printer tomorrow! |
Beta Was this translation helpful? Give feedback.
-
|
You'll love it. This is number 12 Dragon on a 18hr print. I just love looking at that glass smoothness of silk! No problem anytime, just shout out. Through the eye of my Octoprint App.... |
Beta Was this translation helpful? Give feedback.
-
Put a C108 in a new line after the G29 https://github.com/mriscoc/Ender3V2S1/wiki/Slicer-G-code-Scripts |
Beta Was this translation helpful? Give feedback.
-
|
Not sure if this has already been asked, but what is the ProUI box feature and where can I find it? |
Beta Was this translation helpful? Give feedback.
-
|
ProUI is the user interface of Professional Firmware. |
Beta Was this translation helpful? Give feedback.
-
|
Ah, it's the box that appears on the screen when booting the printer. Thanks for the reply :) |
Beta Was this translation helpful? Give feedback.
-
|
I just installed the BigTreeTech SKR Mini E3 V3 into my Ender 3 V2. Where can I find the firmware for this board that supports the CR-Touch? Thank-you! Keep up the good work. :) |
Beta Was this translation helpful? Give feedback.
-
|
U can use same firmware with bl touch |
Beta Was this translation helpful? Give feedback.
-
|
So what firmware version do I use? 4.2.2 or 4.2.7? |
Beta Was this translation helpful? Give feedback.
-
|
If you know how to compile, then use source from https://github.com/mriscoc/Ender3V2S1 And for skr mini e3 v3.0, use configurations from |
Beta Was this translation helpful? Give feedback.
-
|
4.2.2 or 4.2.7 are creality boards |
Beta Was this translation helpful? Give feedback.
-
Yes, I did upgrade the board, so I should use "[Ender3V2-SKRME3V3-BLTUBL-20221002.bin" ? I don't know how to compile. |
Beta Was this translation helpful? Give feedback.
-
|
Yes, u can use that |
Beta Was this translation helpful? Give feedback.
-
|
I just installed the SKR Mini E3 V3 mainboard into my Ender 3 V2 and flashed the Ender3V2-SKRME3V3-MM-20221002.bin and I am having an issue with my Y axis. All settings after the firmware was flashed are original other than the z-offset. Video: Thoughts? |
Beta Was this translation helpful? Give feedback.
-
|
@mriscoc, can you please check this issue with SKR mini e3 v3.0? |
Beta Was this translation helpful? Give feedback.
-
|
Bad Park head Y position, check it in Advanced / Physical Setting / Park head |
Beta Was this translation helpful? Give feedback.
-
|
I was able to fix the park issue by setting the y-position to 205. It will still skip the belt while printing and cause my print to fail. |
Beta Was this translation helpful? Give feedback.
-
|
Follow this guide: https://github.com/mriscoc/Ender3V2S1/wiki/Calibration-Guides but 205 is a very low value for a stock Ender3V2, has your printer a custom fan duct? So, maybe you have a mechanical problem. |
Beta Was this translation helpful? Give feedback.
-
https://github.com/mriscoc/Ender3V2S1/wiki/Physical-Settings-Menu When you change X min and Y min, you MUST change X max and Y max... (X min + X max == 248) and (Y min + Y max == 231). |
Beta Was this translation helpful? Give feedback.
-
|
@mriscoc I installed a CR-touch and flashed the "Ender3V2-SKRME3V3-BLTUBL-20221002.bin" firmware and my issues are resolved. There must be a bug with the manual mesh firmware for the skr mini e3 v3. With that said, I am now having an issue with the display... I am getting weird artifacts after starting a print. https://www.dropbox.com/s/y1wvzxpo5luxkep/screenshot.png?dl=0 https://www.dropbox.com/s/liy9q1415w2sox2/screenshot2.png?dl=0 |
Beta Was this translation helpful? Give feedback.
-
Beta Was this translation helpful? Give feedback.
-
|
@mriscoc How can we blame the SKR mainboard when this issue was not present when I had the manual mesh firmware version installed? This only started happening when I installed the cr-touch firmware version. |
Beta Was this translation helpful? Give feedback.
-
|
Check if you changed the way of wiring, some screen glitches are coming from EMI. |
Beta Was this translation helpful? Give feedback.
-
I purchased the pre-made cable on Amazon for the display: |
Beta Was this translation helpful? Give feedback.
-
|
I have board 4.2.2 and I'm trying to use with a Triangle Labs 3D Touch. Was told by a friend to use the Z endstop pins instead of the BL touch Z output and ground pin on the BL touch header on the board. If the BL touch header on the board has a Z stop input why wouldn't you use that? |
Beta Was this translation helpful? Give feedback.
-
|
This firmware is only compatible with 3d/cr/bltouch installed in the 3d/cr/bltouch header. |
Beta Was this translation helpful? Give feedback.
-
|
So you're saying use the z stop input and ground on the bl touch header and not to use the 2 pin header for the printer's mechanical z stop swtich? The actual z stop switch itself should be disconnected regardless, correct? |
Beta Was this translation helpful? Give feedback.
-
Beta Was this translation helpful? Give feedback.
-
|
Power loss recovery does not work with this firmware. I own 2 Ender 3 V2's one has the SKR Mini E3 V3 board. I was printing on both machines, power went out. BOTH FAILED. Lost huge amount of time and plastic. Has the power loss recovery ever been tested? All it does is heat up the nozzle and bed. Then it parks and asks to wipe the nozzle clean. Then it goes to the home position, heats back up. Goes back to park and asks to wipe again. Then goes to home for a final time before it lowers the z and slowly moves to the right hand size and crashes into the print. Unbelievable. |
Beta Was this translation helpful? Give feedback.
-
|
#469 some users report a successful recovery from power outage, but there are many reports of unreliable functionality because it depends of G-code, SD card, buffers, etc. Sometimes the PLR file gets corrupted because the internal buffers of the SD card were not flushed, that can happen more on large SD cards and complex SD card prints. |
Beta Was this translation helpful? Give feedback.
-
This must be a firmware issue. The exact same prints using the same brand/size memory cards on my Ender6 (4.2.7 mainboard) has never failed me during a power outage on the stock Creality firmware. I was told Jyers firmware supports power loss recovery. I really hate to go back to his firmware but I have no choice at this point. This firmware may be free but it's now cost me significant time and money in filament. |
Beta Was this translation helpful? Give feedback.
-
|
Yes it's free, so maybe a better fix for you is to buy a Battery Backup. Oh but I guess that isn't free. |
Beta Was this translation helpful? Give feedback.
-
|
I have 2 V2's, both have 4.2.7 boards, both recover with no issues as long as the bed doesn't cool and release the build. Otherwise no issues. |
Beta Was this translation helpful? Give feedback.
-
|
Thanks for your report. |
Beta Was this translation helpful? Give feedback.
-
|
The pause function in the firmware is not working. All of them can't pause and resume printing. |
Beta Was this translation helpful? Give feedback.
-
|
If you are looking for a change filament, use M600 I just use it yesterday and is working great. For simple pause use M25. |
Beta Was this translation helpful? Give feedback.
-
|
This is worked well. |
Beta Was this translation helpful? Give feedback.
-
|
I've had my E3V2 for a little over a year now, and have had some level of success with it, but gotta say after installing a PEI print bed to try and start working with PETG, the tramming wizard alone made this firmware amazing and worth while. I look forward to seeing how things turn out as I keep using it. |
Beta Was this translation helpful? Give feedback.
-
|
Ender 3 v2 not stock. I'm using |
Beta Was this translation helpful? Give feedback.
-
|
Check https://github.com/mriscoc/Ender3V2S1/wiki/Calibration-Guides |
Beta Was this translation helpful? Give feedback.
-
|
I am trying to get my ender 3 v2 figured out. I have a 4.2.7 board with Sprite Extruder Pro and CR Touch. I have installed the firmware and I believe I have calibrated everything correctly, however when I auto home my bed the probe does not go to the center of the bed. I am newer to printing and am not good with the codes and all that. Can someone tell me what I am doing wrong |
Beta Was this translation helpful? Give feedback.
-
|
You have to set the probe offsets. I use X-30.00 Y-45.00. |
Beta Was this translation helpful? Give feedback.
-
|
Hello, |
Beta Was this translation helpful? Give feedback.
-
|
Yes, use the g-code |
Beta Was this translation helpful? Give feedback.
-
|
Sorry for what might seem very stupid but I would like to use this version since that's the latest one with PID and not MPC. |
Beta Was this translation helpful? Give feedback.
-
|
You can use the latest version but do not select MPC in the Configurator so the firmware will support PID. |
Beta Was this translation helpful? Give feedback.
-
|
I would love to do so but I am afraid I do not know how to. |
Beta Was this translation helpful? Give feedback.
and others
-
AUSTRAL SPRING
What's new in this release
From last Marlin bugfix 2.1.x
This firmware is based on Marlin, has been optimized and has enhancements for the Creality Ender 3 V2/S1 printer. This is an universal firmware that can be used in both RET6 and RCT6 STM32FX chips that have 256k or 512k Flash memory.
Requirements
In order to use this firmware, your printer must meet the following requirements:
You can modify your printer to meet these requirements.
Versions
UBL versions
Binaries with UBL in their filename have support for Marlin Unified Bed Leveling, this system is similar to the bilinear leveling but with a few extra features to provide users with more control. There are multiple guides on the web about UBL, we recommend reading about it before using this new leveling system.
You can download the latest binaries from the assets at the bottom of
the release page.
To know if you have the last release go to the info page in the display of
your printer and compare the release build date with the name of the binary
file. The filename follows the convention:
Where YYYYMMDD indicates the date of the build. 422 refers to the mainboard
version 4.2.2, 423 refers to the mainboard version 4.2.3, and 427 is for the 4.2.7 mainboard version, if you got
a 4.3.1 board use the 422 version. SKRMINI version is currently for the
BTT SKR Mini E3 V3 board (needs a screen adapter).
For example if you want a firmware for your Ender-3 V2 printer with a control
board version 4.2.2, CRTouch and support for UBL, you should download the file:
Special versions
There are several special configurations here: https://github.com/mriscoc/Marlin_Configurations/releases
Community links
Donations
Thank you for your support, I receive donations through Patreon and Paypal
Firmware features
Manual mesh
CR/3D/BLTouch
G-Codes enhanced support
Support for special nonstandard custom C G-Codes
version, Z parameter can be used to set a manual Z-offset.
Advanced settings menu
Special Octoprint / Host print support
Octoprint bed visualizer support
Display enhancements
A lot of additions and fixes from Bugfix development branch
More info on the wiki pages
How to install the firmware
Octoprint settings
How to make the Manual Mesh
How to install a 3D/BLTouch
How to apply a color theme
20211121.mp4
Precompiled firmware
This discussion was created from the release Ender3 V2/S1 Professional Firmware 20221002.
Beta Was this translation helpful? Give feedback.
All reactions