platformio.ini

; HAN V1.32

[platformio]
default_envs = 
    nodemcuv2
    ;ttgo_lora32_v21
    ;esp32_c3

; ------------------------------------------------------------------------------
; |  Common Settings                                                           |
; |                                                                            |
; |  These settings are shared by all board configurations except for          |
; |  nodemcuv2 which uses its own monitor_speed setting.                       |
; ------------------------------------------------------------------------------

[common]

monitor_speed = 9600

build_flags =
    -D DO_WORK_INTERVAL_SECONDS=31

    ; -D ABP_ACTIVATION                ; Use ABP instead of OTAA activation.
    ;
    ; -D WAITFOR_SERIAL_SECONDS=10     ; Can be used to override the default value (10).
    ;                                    Is used only for boards with default set to != 0 in BSF.
    ;
    ; -D LMIC_CLOCK_ERROR_PPM=0        ; If not defined defines, otherwise overrides value defined in BSF.
    ;                                    Is for testing purposes only.
    ;                                    Do not enable this unless you explicitly know what you are doing.
    ;
    ; -D STM32_POST_INITSERIAL_DELAY_MS=1500  ; Workaround for STM32 boards. Can be used 
    ;                                           to override value (milliseconds) in BSF.

lib_deps =
    ModbusMaster
    LoRa

; -------------------------------
; |  Shortcuts and Workarounds  |
; -------------------------------

[esp32]
build_flags =
    -D hal_init=LMICHAL_init           ; Workaround for naming conflict of function hal_init
                                       ; introduced by newer versions (> 3.5.0) of 
                                       ; PlatformIO Espressif 32 platform (ESP32 Arduino core).
                                       ; See https://github.com/lnlp/LMIC-node/issues/41 for more information.

[pico]
upload_port = E:                       ; Shortcut for Raspberry Pi Pico. 
                                       ; Operating system and hardware dependent.
                                       ; Placed here so it can be easily changed.
                                       ; See section [env:pico] below for more information.


; --------------------------------------------------
; |  MCCI LoRaWAN LMIC library specific settings   |
; --------------------------------------------------

[mcci_lmic]
; LMIC-node was tested with MCCI LoRaWAN LMIC library v3.3.0 and v4.0.0.
; Some changes have been announced for future versions of the MCCI library
; which may be incompatible with LMIC-node. In case of problems just
; use mcci-catena/MCCI LoRaWAN LMIC library@4.0.0 below which will
; explicitly use v4.0.0 of the library.
; Perform 'PlatformIO: Clean' after changing library version and
; in case of issues remove the old version from .pio/libdeps/*.

; Note: LMIC_PRINTF_TO is defined for each board separately
;       in the board specific sections. Don't define it in this section.

lib_deps =
    ; Only ONE of below LMIC libraries should be enabled.
    mcci-catena/MCCI LoRaWAN LMIC library           ; MCCI LMIC library (latest release)
    ; mcci-catena/MCCI LoRaWAN LMIC library@4.0.0   ; MCCI LMIC library v4.0.0

build_flags =
    ; Use platformio.ini for settings instead lmic_project_config.h.
    -D ARDUINO_LMIC_PROJECT_CONFIG_H_SUPPRESS

    ; Ping and beacons not supported for class A, disable to save memory.
    -D DISABLE_PING
    -D DISABLE_BEACONS

    ; -D LMIC_DEBUG_LEVEL=1            ; 0, 1 or 2
    
    ; -D CFG_sx1272_radio=1            ; Use for SX1272 radio
    -D CFG_sx1276_radio=1              ; Use for SX1276 radio
    -D USE_ORIGINAL_AES                ; Faster but larger, see docs
    ; -D LMIC_USE_INTERRUPTS           ; Not tested or supported on many platforms
    ; -D LMIC_ENABLE_DeviceTimeReq=1   ; Network time support

    ; --- Regional settings -----
    ; Enable only one of the following regions:    
    ; -D CFG_as923=1
    ; -D CFG_as923jp=1   
    ; -D CFG_au915=1
    ; -D CFG_cn490=1                   ; Not yet supported
    ; -D CFG_cn783=1                   ; Not yet supported
    ; -D CFG_eu433=1                   ; Not yet supported
    -D CFG_eu868=1
    ; -D CFG_in866=1
    ; -D CFG_kr920=1
    ; -D CFG_us915=1

; --------------------------------------------------
; |  ENV                                           |
; --------------------------------------------------

[env:nodemcuv2]
platform = espressif8266
board = esp07s
framework = arduino
lib_deps =
    ;ESP8266WiFi
    ${common.lib_deps}    
    ${mcci_lmic.lib_deps}
build_flags =
    ${common.build_flags}
    ${mcci_lmic.build_flags} 
    -D BSFILE=\"bsf_nodemcuv2.h\"
    -D MONITOR_SPEED=9600
    -D _GNU_SOURCE
    -D USE_SERIAL
    -w

[env:ttgo_lora32_v21]
platform = espressif32
board = ttgo-lora32-v21
framework = arduino
monitor_speed = ${common.monitor_speed}
lib_deps =
    ${common.lib_deps}    
    ${mcci_lmic.lib_deps}
build_flags =
    ${common.build_flags}
    ${esp32.build_flags}
    ${mcci_lmic.build_flags} 
    -D BSFILE=\"bsf_ttgo_lora32_v21.h\"
    -D MONITOR_SPEED=${common.monitor_speed}
    -D LMIC_PRINTF_TO=Serial
    -D USE_SERIAL
    -w

[env:esp32_c3]
platform = espressif32
board = esp32-c3-devkitm-1
framework = arduino
monitor_speed = ${common.monitor_speed}
lib_deps =
    ${common.lib_deps}    
    ${mcci_lmic.lib_deps}
build_flags =
    ${common.build_flags}
    ${esp32.build_flags}
    ${mcci_lmic.build_flags} 
    -D BSFILE=\"bsf_esp32_c3.h\"
    -D MONITOR_SPEED=${common.monitor_speed}
    -D LMIC_PRINTF_TO=Serial
    -D USE_SERIAL
    -w

; EOF