phb4.c

/* Copyright 2013-2016 IBM Corp.
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 * 	http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or
 * implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */
/*
 * PHB4 support
 *
 */

/*
 *
 * FIXME:
 *   More stuff for EEH support:
 *      - PBCQ error reporting interrupt
 *	- I2C-based power management (replacing SHPC)
 *	- Directly detect fenced PHB through one dedicated HW reg
 */

/*
 * This is a simplified view of the PHB4 reset and link training steps
 *
 * Step 1:
 * - Check for hotplug status:
 *  o PHB_PCIE_HOTPLUG_STATUS bit PHB_PCIE_HPSTAT_PRESENCE
 *  o If not set -> Bail out (Slot is empty)
 *
 * Step 2:
 * - Do complete PHB reset:
 *   o PHB/ETU reset procedure
 *
 * Step 3:
 * - Drive PERST active (skip if already asserted. ie. after cold reboot)
 * - Wait 250ms (for cards to reset)
 *   o powervm have used 250ms for a long time without any problems
 *
 * Step 4:
 * - Drive PERST inactive
 *
 * Step 5:
 * - Look for inband presence:
 *   o From PERST we have two stages to get inband presence detected
 *     1) Devices must enter Detect state within 20 ms of the end of
 *          Fundamental Reset
 *     2) Receiver detect pulse are every 12ms
 *      - Hence minimum wait time 20 + 12 = 32ms
 *   o Unfortunatey, we've seen cards take 440ms
 *   o Hence we are conservative and poll here for 1000ms (> 440ms)
 * - If no inband presence after 100ms -> Bail out (Slot is broken)
 *   o PHB_PCIE_DLP_TRAIN_CTL bit PHB_PCIE_DLP_INBAND_PRESENCE
 *
 * Step 6:
 * - Look for link training done:
 *   o PHB_PCIE_DLP_TRAIN_CTL bit PHB_PCIE_DLP_TL_LINKACT
 * - If not set after 2000ms, Retry (3 times) -> Goto Step 2
 *   o phy lockup could link training failure, hence going back to a
 *     complete PHB reset on retry
 *   o not expect to happen very often
 *
 * Step 7:
 * - Wait for 1 sec (before touching device config space):
 * -  From PCIe spec:
 *     Root Complex and/or system software must allow at least 1.0 s after
 *     a Conventional Reset of a device, before it may determine that a
 *     device which fails to return a Successful Completion status for a
 *     valid Configuration Request is a broken device.
 *
 * Step 8:
 * - Sanity check for fence and link still up:
 *   o If fenced or link down, Retry (3 times) -> Goto Step 2
 *   o This is not nessary but takes no time and can be useful
 *   o Once we leave here, much harder to recover from errors
 *
 * Step 9:
 * - Check for optimised link for directly attached devices:
 *   o Wait for CRS (so we can read device config space)
 *   o Check chip and device are in whitelist. if not, Goto Step 10
 *   o If trained link speed is degraded, retry ->  Goto Step 2
 *   o If trained link width is degraded, retry -> Goto Step 2
 *   o If still degraded after 3 retries. Give up, Goto Step 10.
 *
 * Step 10:
 *  - PHB good, start probing config space.
 *    o core/pci.c: pci_reset_phb() -> pci_scan_phb()
 */


#undef NO_ASB
#undef LOG_CFG

#include <skiboot.h>
#include <io.h>
#include <timebase.h>
#include <pci.h>
#include <pci-cfg.h>
#include <pci-slot.h>
#include <vpd.h>
#include <interrupts.h>
#include <opal.h>
#include <cpu.h>
#include <device.h>
#include <ccan/str/str.h>
#include <ccan/array_size/array_size.h>
#include <xscom.h>
#include <affinity.h>
#include <phb4.h>
#include <phb4-regs.h>
#include <phb4-capp.h>
#include <capp.h>
#include <fsp.h>
#include <chip.h>
#include <chiptod.h>
#include <xive.h>
#include <xscom-p9-regs.h>
#include <phys-map.h>
#include <nvram.h>

/* Enable this to disable error interrupts for debug purposes */
#define DISABLE_ERR_INTS

static void phb4_init_hw(struct phb4 *p, bool first_init);

#define PHBDBG(p, fmt, a...)	prlog(PR_DEBUG, "PHB#%04x[%d:%d]: " fmt, \
				      (p)->phb.opal_id, (p)->chip_id, \
				      (p)->index,  ## a)
#define PHBINF(p, fmt, a...)	prlog(PR_INFO, "PHB#%04x[%d:%d]: " fmt, \
				      (p)->phb.opal_id, (p)->chip_id, \
				      (p)->index,  ## a)
#define PHBERR(p, fmt, a...)	prlog(PR_ERR, "PHB#%04x[%d:%d]: " fmt, \
				      (p)->phb.opal_id, (p)->chip_id, \
				      (p)->index,  ## a)
#ifdef LOG_CFG
#define PHBLOGCFG(p, fmt, a...)	PHBDBG(p, fmt, ## a)
#else
#define PHBLOGCFG(p, fmt, a...) do {} while (0)
#endif

static bool verbose_eeh;
static bool pci_tracing;
static bool pci_eeh_mmio;
static bool pci_retry_all;

enum capi_dma_tvt {
	CAPI_DMA_TVT0,
	CAPI_DMA_TVT1,
};

/* Note: The "ASB" name is historical, practically this means access via
 * the XSCOM backdoor
 */
static inline uint64_t phb4_read_reg_asb(struct phb4 *p, uint32_t offset)
{
#ifdef NO_ASB
	return in_be64(p->regs + offset);
#else
	int64_t rc;
	uint64_t addr, val;

	/* Address register: must use 4 bytes for built-in config space.
	 *
	 * This path isn't usable for outbound configuration space
	 */
	if (((offset & 0xfffffffc) == PHB_CONFIG_DATA) && (offset & 3)) {
		PHBERR(p, "XSCOM unaligned access to CONFIG_DATA unsupported\n");
		return -1ull;
	}
	addr = XETU_HV_IND_ADDR_VALID | offset;
	if ((offset >= 0x1000 && offset < 0x1800) || (offset == PHB_CONFIG_DATA))
		addr |= XETU_HV_IND_ADDR_4B;
 	rc = xscom_write(p->chip_id, p->etu_xscom + XETU_HV_IND_ADDRESS, addr);
	if (rc != 0) {
		PHBERR(p, "XSCOM error addressing register 0x%x\n", offset);
		return -1ull;
	}
 	rc = xscom_read(p->chip_id, p->etu_xscom + XETU_HV_IND_DATA, &val);
	if (rc != 0) {
		PHBERR(p, "XSCOM error reading register 0x%x\n", offset);
		return -1ull;
	}
	return val;
#endif
}

static inline void phb4_write_reg_asb(struct phb4 *p,
				      uint32_t offset, uint64_t val)
{
#ifdef NO_ASB
	out_be64(p->regs + offset, val);
#else
	int64_t rc;
	uint64_t addr;

	/* Address register: must use 4 bytes for built-in config space.
	 *
	 * This path isn't usable for outbound configuration space
	 */
	if (((offset & 0xfffffffc) == PHB_CONFIG_DATA) && (offset & 3)) {
		PHBERR(p, "XSCOM access to CONFIG_DATA unsupported\n");
		return;
	}
	addr = XETU_HV_IND_ADDR_VALID | offset;
	if ((offset >= 0x1000 && offset < 0x1800) || (offset == PHB_CONFIG_DATA))
		addr |= XETU_HV_IND_ADDR_4B;
 	rc = xscom_write(p->chip_id, p->etu_xscom + XETU_HV_IND_ADDRESS, addr);
	if (rc != 0) {
		PHBERR(p, "XSCOM error addressing register 0x%x\n", offset);
		return;
	}
 	rc = xscom_write(p->chip_id, p->etu_xscom + XETU_HV_IND_DATA, val);
	if (rc != 0) {
		PHBERR(p, "XSCOM error writing register 0x%x\n", offset);
		return;
	}
#endif
}

static uint64_t phb4_read_reg(struct phb4 *p, uint32_t offset)
{
	if (p->flags & PHB4_CFG_USE_ASB)
		return phb4_read_reg_asb(p, offset);
	else
		return in_be64(p->regs + offset);
}

static void phb4_write_reg(struct phb4 *p, uint32_t offset, uint64_t val)
{
	if (p->flags & PHB4_CFG_USE_ASB)
		phb4_write_reg_asb(p, offset, val);
	else
		return out_be64(p->regs + offset, val);
}

/* Helper to select an IODA table entry */
static inline void phb4_ioda_sel(struct phb4 *p, uint32_t table,
				 uint32_t addr, bool autoinc)
{
	phb4_write_reg(p, PHB_IODA_ADDR,
		       (autoinc ? PHB_IODA_AD_AUTOINC : 0)	|
		       SETFIELD(PHB_IODA_AD_TSEL, 0ul, table)	|
		       SETFIELD(PHB_IODA_AD_TADR, 0ul, addr));
}

/*
 * Configuration space access
 *
 * The PHB lock is assumed to be already held
 */
static int64_t phb4_pcicfg_check(struct phb4 *p, uint32_t bdfn,
				 uint32_t offset, uint32_t size,
				 uint8_t *pe)
{
	uint32_t sm = size - 1;

	if (offset > 0xfff || bdfn > 0xffff)
		return OPAL_PARAMETER;
	if (offset & sm)
		return OPAL_PARAMETER;

	/* The root bus only has a device at 0 and we get into an
	 * error state if we try to probe beyond that, so let's
	 * avoid that and just return an error to Linux
	 */
	if ((bdfn >> 8) == 0 && (bdfn & 0xff))
		return OPAL_HARDWARE;

	/* Check PHB state */
	if (p->state == PHB4_STATE_BROKEN)
		return OPAL_HARDWARE;

	/* Fetch the PE# from cache */
	*pe = p->rte_cache[bdfn];

	return OPAL_SUCCESS;
}

static int64_t phb4_rc_read(struct phb4 *p, uint32_t offset, uint8_t sz,
			    void *data, bool use_asb)
{
	uint32_t reg = offset & ~3;
	uint32_t oval;

	/* Some registers are handled locally */
	switch (reg) {
		/* Bridge base/limit registers are cached here as HW
		 * doesn't implement them (it hard codes values that
		 * will confuse a proper PCI implementation).
		 */
	case PCI_CFG_MEM_BASE:		/* Includes PCI_CFG_MEM_LIMIT */
		oval = p->rc_cache[(reg - 0x20) >> 2] & 0xfff0fff0;
		break;
	case PCI_CFG_PREF_MEM_BASE:	/* Includes PCI_CFG_PREF_MEM_LIMIT */
		oval = p->rc_cache[(reg - 0x20) >> 2] & 0xfff0fff0;
		oval |= 0x00010001;
		break;
	case PCI_CFG_IO_BASE_U16:	/* Includes PCI_CFG_IO_LIMIT_U16 */
		oval = 0;
		break;
	case PCI_CFG_PREF_MEM_BASE_U32:
	case PCI_CFG_PREF_MEM_LIMIT_U32:
		oval = p->rc_cache[(reg - 0x20) >> 2];
		break;
	default:
		oval = 0xffffffff; /* default if offset too big */
		if (reg < PHB_RC_CONFIG_SIZE) {
			if (use_asb)
				oval = bswap_32(phb4_read_reg_asb(p, PHB_RC_CONFIG_BASE
								  + reg));
			else
				oval = in_le32(p->regs + PHB_RC_CONFIG_BASE + reg);
		}
	}
	switch (sz) {
	case 1:
		offset &= 3;
		*((uint8_t *)data) = (oval >> (offset << 3)) & 0xff;
		PHBLOGCFG(p, "000 CFG08 Rd %02x=%02x\n",
			  offset, *((uint8_t *)data));
		break;
	case 2:
		offset &= 2;
		*((uint16_t *)data) = (oval >> (offset << 3)) & 0xffff;
		PHBLOGCFG(p, "000 CFG16 Rd %02x=%04x\n",
			  offset, *((uint16_t *)data));
		break;
	case 4:
		*((uint32_t *)data) = oval;
		PHBLOGCFG(p, "000 CFG32 Rd %02x=%08x\n",
			  offset, *((uint32_t *)data));
		break;
	default:
		assert(false);
	}
	return OPAL_SUCCESS;
}

static int64_t phb4_rc_write(struct phb4 *p, uint32_t offset, uint8_t sz,
			     uint32_t val, bool use_asb)
{
	uint32_t reg = offset & ~3;
	uint32_t old, mask, shift, oldold;
	int64_t rc;

	if (reg > PHB_RC_CONFIG_SIZE)
		return OPAL_SUCCESS;

	/* If size isn't 4-bytes, do a RMW cycle */
	if (sz < 4) {
		rc = phb4_rc_read(p, reg, 4, &old, use_asb);
		if (rc != OPAL_SUCCESS)
			return rc;

		/*
		 * Since we have to Read-Modify-Write here, we need to filter
		 * out registers that have write-1-to-clear bits to prevent
		 * clearing stuff we shouldn't be.  So for any register this
		 * applies to, mask out those bits.
		 */
		oldold = old;
		switch(reg) {
		case 0x1C: /* Secondary status */
			old &= 0x00ffffff; /* mask out 24-31 */
			break;
		case 0x50: /* EC - Device status */
			old &= 0xfff0ffff; /* mask out 16-19 */
			break;
		case 0x58: /* EC - Link status */
			old &= 0x3fffffff; /* mask out 30-31 */
			break;
		case 0x78: /* EC - Link status 2 */
			old &= 0xf000ffff; /* mask out 16-27 */
			break;
		/* These registers *only* have write-1-to-clear bits */
		case 0x104: /* AER - Uncorr. error status */
		case 0x110: /* AER - Corr. error status */
		case 0x130: /* AER - Root error status */
		case 0x180: /* P16 - status */
		case 0x184: /* P16 - LDPM status */
		case 0x188: /* P16 - FRDPM status */
		case 0x18C: /* P16 - SRDPM status */
			old &= 0x00000000;
			break;
		}

		if (old != oldold) {
			PHBLOGCFG(p, "Rewrote %x to %x for reg %x for W1C\n",
				  oldold, old, reg);
		}

		if (sz == 1) {
			shift = (offset & 3) << 3;
			mask = 0xff << shift;
			val = (old & ~mask) | ((val & 0xff) << shift);
		} else {
			shift = (offset & 2) << 3;
			mask = 0xffff << shift;
			val = (old & ~mask) | ((val & 0xffff) << shift);
		}
	}

	/* Some registers are handled locally */
	switch (reg) {
		/* See comment in phb4_rc_read() */
	case PCI_CFG_MEM_BASE:		/* Includes PCI_CFG_MEM_LIMIT */
	case PCI_CFG_PREF_MEM_BASE:	/* Includes PCI_CFG_PREF_MEM_LIMIT */
	case PCI_CFG_PREF_MEM_BASE_U32:
	case PCI_CFG_PREF_MEM_LIMIT_U32:
		p->rc_cache[(reg - 0x20) >> 2] = val;
		break;
	case PCI_CFG_IO_BASE_U16:	/* Includes PCI_CFG_IO_LIMIT_U16 */
		break;
	default:
		/* Workaround PHB config space enable */
		if ((p->rev == PHB4_REV_NIMBUS_DD10) && (reg == PCI_CFG_CMD))
			val |= PCI_CFG_CMD_MEM_EN | PCI_CFG_CMD_BUS_MASTER_EN;
		PHBLOGCFG(p, "000 CFG%02d Wr %02x=%08x\n", 8 * sz, reg, val);
		if (use_asb)
			phb4_write_reg_asb(p, PHB_RC_CONFIG_BASE + reg, val);
		else
			out_le32(p->regs + PHB_RC_CONFIG_BASE + reg, val);
	}
	return OPAL_SUCCESS;
}

static int64_t phb4_pcicfg_read(struct phb4 *p, uint32_t bdfn,
				uint32_t offset, uint32_t size,
				void *data)
{
	uint64_t addr, val64;
	int64_t rc;
	uint8_t pe;
	bool use_asb = false;

	rc = phb4_pcicfg_check(p, bdfn, offset, size, &pe);
	if (rc)
		return rc;

	if (p->flags & PHB4_AIB_FENCED) {
		if (!(p->flags & PHB4_CFG_USE_ASB))
			return OPAL_HARDWARE;
		if (bdfn != 0)
			return OPAL_HARDWARE;
		use_asb = true;
	} else if ((p->flags & PHB4_CFG_BLOCKED) && bdfn != 0) {
		return OPAL_HARDWARE;
	}

	/* Handle per-device filters */
	rc = pci_handle_cfg_filters(&p->phb, bdfn, offset, size,
				    (uint32_t *)data, false);
	if (rc != OPAL_PARTIAL)
		return rc;

	/* Handle root complex MMIO based config space */
	if (bdfn == 0)
		return phb4_rc_read(p, offset, size, data, use_asb);

	addr = PHB_CA_ENABLE;
	addr = SETFIELD(PHB_CA_BDFN, addr, bdfn);
	addr = SETFIELD(PHB_CA_REG, addr, offset & ~3u);
	addr = SETFIELD(PHB_CA_PE, addr, pe);
	if (use_asb) {
		phb4_write_reg_asb(p, PHB_CONFIG_ADDRESS, addr);
		sync();
		val64 = bswap_64(phb4_read_reg_asb(p, PHB_CONFIG_DATA));
		switch(size) {
		case 1:
			*((uint8_t *)data) = val64 >> (8 * (offset & 3));
			break;
		case 2:
			*((uint16_t *)data) = val64 >> (8 * (offset & 2));
			break;
		case 4:
			*((uint32_t *)data) = val64;
			break;
		default:
			return OPAL_PARAMETER;
		}
	} else {
		out_be64(p->regs + PHB_CONFIG_ADDRESS, addr);
		switch(size) {
		case 1:
			*((uint8_t *)data) =
				in_8(p->regs + PHB_CONFIG_DATA + (offset & 3));
			PHBLOGCFG(p, "%03x CFG08 Rd %02x=%02x\n",
				  bdfn, offset, *((uint8_t *)data));
			break;
		case 2:
			*((uint16_t *)data) =
				in_le16(p->regs + PHB_CONFIG_DATA + (offset & 2));
			PHBLOGCFG(p, "%03x CFG16 Rd %02x=%04x\n",
				  bdfn, offset, *((uint16_t *)data));
			break;
		case 4:
			*((uint32_t *)data) = in_le32(p->regs + PHB_CONFIG_DATA);
			PHBLOGCFG(p, "%03x CFG32 Rd %02x=%08x\n",
				  bdfn, offset, *((uint32_t *)data));
			break;
		default:
			return OPAL_PARAMETER;
		}
	}
	return OPAL_SUCCESS;
}


#define PHB4_PCI_CFG_READ(size, type)					\
static int64_t phb4_pcicfg_read##size(struct phb *phb, uint32_t bdfn,	\
				      uint32_t offset, type *data)	\
{									\
	struct phb4 *p = phb_to_phb4(phb);				\
									\
	/* Initialize data in case of error */				\
	*data = (type)0xffffffff;					\
	return phb4_pcicfg_read(p, bdfn, offset, sizeof(type), data);	\
}

static int64_t phb4_pcicfg_write(struct phb4 *p, uint32_t bdfn,
				 uint32_t offset, uint32_t size,
				 uint32_t data)
{
	uint64_t addr;
	int64_t rc;
	uint8_t pe;
	bool use_asb = false;

	rc = phb4_pcicfg_check(p, bdfn, offset, size, &pe);
	if (rc)
		return rc;

	if (p->flags & PHB4_AIB_FENCED) {
		if (!(p->flags & PHB4_CFG_USE_ASB))
			return OPAL_HARDWARE;
		if (bdfn != 0)
			return OPAL_HARDWARE;
		use_asb = true;
	} else if ((p->flags & PHB4_CFG_BLOCKED) && bdfn != 0) {
		return OPAL_HARDWARE;
	}

	/* Handle per-device filters */
	rc = pci_handle_cfg_filters(&p->phb, bdfn, offset, size,
				    (uint32_t *)&data, true);
	if (rc != OPAL_PARTIAL)
		return rc;

	/* Handle root complex MMIO based config space */
	if (bdfn == 0)
		return phb4_rc_write(p, offset, size, data, use_asb);

	addr = PHB_CA_ENABLE;
	addr = SETFIELD(PHB_CA_BDFN, addr, bdfn);
	addr = SETFIELD(PHB_CA_REG, addr, offset & ~3u);
	addr = SETFIELD(PHB_CA_PE, addr, pe);
	if (use_asb) {
		/* We don't support ASB config space writes */
		return OPAL_UNSUPPORTED;
	} else {
		out_be64(p->regs + PHB_CONFIG_ADDRESS, addr);
		switch(size) {
		case 1:
			out_8(p->regs + PHB_CONFIG_DATA + (offset & 3), data);
			break;
		case 2:
			out_le16(p->regs + PHB_CONFIG_DATA + (offset & 2), data);
			break;
		case 4:
			out_le32(p->regs + PHB_CONFIG_DATA, data);
			break;
		default:
			return OPAL_PARAMETER;
		}
	}
	PHBLOGCFG(p, "%03x CFG%d Wr %02x=%08x\n", bdfn, 8 * size, offset, data);
	return OPAL_SUCCESS;
}

#define PHB4_PCI_CFG_WRITE(size, type)					\
static int64_t phb4_pcicfg_write##size(struct phb *phb, uint32_t bdfn,	\
				       uint32_t offset, type data)	\
{									\
	struct phb4 *p = phb_to_phb4(phb);				\
									\
	return phb4_pcicfg_write(p, bdfn, offset, sizeof(type), data);	\
}

PHB4_PCI_CFG_READ(8, u8)
PHB4_PCI_CFG_READ(16, u16)
PHB4_PCI_CFG_READ(32, u32)
PHB4_PCI_CFG_WRITE(8, u8)
PHB4_PCI_CFG_WRITE(16, u16)
PHB4_PCI_CFG_WRITE(32, u32)

static uint8_t phb4_choose_bus(struct phb *phb __unused,
			       struct pci_device *bridge __unused,
			       uint8_t candidate, uint8_t *max_bus __unused,
			       bool *use_max)
{
	/* Use standard bus number selection */
	*use_max = false;
	return candidate;
}

static int64_t phb4_get_reserved_pe_number(struct phb *phb)
{
	struct phb4 *p = phb_to_phb4(phb);

	return PHB4_RESERVED_PE_NUM(p);
}


static void phb4_root_port_init(struct phb *phb, struct pci_device *dev,
				int ecap, int aercap)
{
	uint16_t bdfn = dev->bdfn;
	uint16_t val16;
	uint32_t val32;

	/*
	 * Use the PHB's callback so that UTL events will be masked or
	 * unmasked when the link is down or up.
	 */
	if (dev->slot && dev->slot->ops.prepare_link_change &&
	    phb->slot && phb->slot->ops.prepare_link_change)
		dev->slot->ops.prepare_link_change =
			phb->slot->ops.prepare_link_change;

	// FIXME: check recommended init values for phb4

	/* Enable SERR and parity checking */
	pci_cfg_read16(phb, bdfn, PCI_CFG_CMD, &val16);
	val16 |= (PCI_CFG_CMD_SERR_EN | PCI_CFG_CMD_PERR_RESP |
		  PCI_CFG_CMD_MEM_EN);
	pci_cfg_write16(phb, bdfn, PCI_CFG_CMD, val16);

	/* Enable reporting various errors */
	if (!ecap) return;
	pci_cfg_read16(phb, bdfn, ecap + PCICAP_EXP_DEVCTL, &val16);
	val16 |= (PCICAP_EXP_DEVCTL_CE_REPORT |
		  PCICAP_EXP_DEVCTL_NFE_REPORT |
		  PCICAP_EXP_DEVCTL_FE_REPORT |
		  PCICAP_EXP_DEVCTL_UR_REPORT);
	pci_cfg_write16(phb, bdfn, ecap + PCICAP_EXP_DEVCTL, val16);

	if (!aercap) return;

	/* Mask various unrecoverable errors */
	pci_cfg_read32(phb, bdfn, aercap + PCIECAP_AER_UE_MASK, &val32);
	val32 |= (PCIECAP_AER_UE_MASK_POISON_TLP |
		  PCIECAP_AER_UE_MASK_COMPL_TIMEOUT |
		  PCIECAP_AER_UE_MASK_COMPL_ABORT |
		  PCIECAP_AER_UE_MASK_ECRC);
	pci_cfg_write32(phb, bdfn, aercap + PCIECAP_AER_UE_MASK, val32);

	/* Report various unrecoverable errors as fatal errors */
	pci_cfg_read32(phb, bdfn, aercap + PCIECAP_AER_UE_SEVERITY, &val32);
	val32 |= (PCIECAP_AER_UE_SEVERITY_DLLP |
		  PCIECAP_AER_UE_SEVERITY_SURPRISE_DOWN |
		  PCIECAP_AER_UE_SEVERITY_FLOW_CTL_PROT |
		  PCIECAP_AER_UE_SEVERITY_UNEXP_COMPL |
		  PCIECAP_AER_UE_SEVERITY_RECV_OVFLOW |
		  PCIECAP_AER_UE_SEVERITY_MALFORMED_TLP);
	pci_cfg_write32(phb, bdfn, aercap + PCIECAP_AER_UE_SEVERITY, val32);

	/* Mask various recoverable errors */
	pci_cfg_read32(phb, bdfn, aercap + PCIECAP_AER_CE_MASK, &val32);
	val32 |= PCIECAP_AER_CE_MASK_ADV_NONFATAL;
	pci_cfg_write32(phb, bdfn, aercap + PCIECAP_AER_CE_MASK, val32);

	/* Enable ECRC check */
	pci_cfg_read32(phb, bdfn, aercap + PCIECAP_AER_CAPCTL, &val32);
	val32 |= (PCIECAP_AER_CAPCTL_ECRCG_EN |
		  PCIECAP_AER_CAPCTL_ECRCC_EN);
	pci_cfg_write32(phb, bdfn, aercap + PCIECAP_AER_CAPCTL, val32);

	/* Enable all error reporting */
	pci_cfg_read32(phb, bdfn, aercap + PCIECAP_AER_RERR_CMD, &val32);
	val32 |= (PCIECAP_AER_RERR_CMD_FE |
		  PCIECAP_AER_RERR_CMD_NFE |
		  PCIECAP_AER_RERR_CMD_CE);
	pci_cfg_write32(phb, bdfn, aercap + PCIECAP_AER_RERR_CMD, val32);
}

static void phb4_switch_port_init(struct phb *phb,
				  struct pci_device *dev,
				  int ecap, int aercap)
{
	uint16_t bdfn = dev->bdfn;
	uint16_t val16;
	uint32_t val32;

	// FIXME: update AER settings for phb4

	/* Enable SERR and parity checking and disable INTx */
	pci_cfg_read16(phb, bdfn, PCI_CFG_CMD, &val16);
	val16 |= (PCI_CFG_CMD_PERR_RESP |
		  PCI_CFG_CMD_SERR_EN |
		  PCI_CFG_CMD_INTx_DIS);
	pci_cfg_write16(phb, bdfn, PCI_CFG_CMD, val16);

	/* Disable partity error and enable system error */
	pci_cfg_read16(phb, bdfn, PCI_CFG_BRCTL, &val16);
	val16 &= ~PCI_CFG_BRCTL_PERR_RESP_EN;
	val16 |= PCI_CFG_BRCTL_SERR_EN;
	pci_cfg_write16(phb, bdfn, PCI_CFG_BRCTL, val16);

	/* Enable reporting various errors */
	if (!ecap) return;
	pci_cfg_read16(phb, bdfn, ecap + PCICAP_EXP_DEVCTL, &val16);
	val16 |= (PCICAP_EXP_DEVCTL_CE_REPORT |
		  PCICAP_EXP_DEVCTL_NFE_REPORT |
		  PCICAP_EXP_DEVCTL_FE_REPORT);
	/* HW279570 - Disable reporting of correctable errors */
	val16 &= ~PCICAP_EXP_DEVCTL_CE_REPORT;
	pci_cfg_write16(phb, bdfn, ecap + PCICAP_EXP_DEVCTL, val16);

	/* Unmask all unrecoverable errors */
	if (!aercap) return;
	pci_cfg_write32(phb, bdfn, aercap + PCIECAP_AER_UE_MASK, 0x0);

	/* Severity of unrecoverable errors */
	if (dev->dev_type == PCIE_TYPE_SWITCH_UPPORT)
		val32 = (PCIECAP_AER_UE_SEVERITY_DLLP |
			 PCIECAP_AER_UE_SEVERITY_SURPRISE_DOWN |
			 PCIECAP_AER_UE_SEVERITY_FLOW_CTL_PROT |
			 PCIECAP_AER_UE_SEVERITY_RECV_OVFLOW |
			 PCIECAP_AER_UE_SEVERITY_MALFORMED_TLP |
			 PCIECAP_AER_UE_SEVERITY_INTERNAL);
	else
		val32 = (PCIECAP_AER_UE_SEVERITY_FLOW_CTL_PROT |
			 PCIECAP_AER_UE_SEVERITY_INTERNAL);
	pci_cfg_write32(phb, bdfn, aercap + PCIECAP_AER_UE_SEVERITY, val32);

	/*
	 * Mask various correctable errors
	 */
	val32 = PCIECAP_AER_CE_MASK_ADV_NONFATAL;
	pci_cfg_write32(phb, bdfn, aercap + PCIECAP_AER_CE_MASK, val32);

	/* Enable ECRC generation and disable ECRC check */
	pci_cfg_read32(phb, bdfn, aercap + PCIECAP_AER_CAPCTL, &val32);
	val32 |= PCIECAP_AER_CAPCTL_ECRCG_EN;
	val32 &= ~PCIECAP_AER_CAPCTL_ECRCC_EN;
	pci_cfg_write32(phb, bdfn, aercap + PCIECAP_AER_CAPCTL, val32);
}

static void phb4_endpoint_init(struct phb *phb,
			       struct pci_device *dev,
			       int ecap, int aercap)
{
	uint16_t bdfn = dev->bdfn;
	uint16_t val16;
	uint32_t val32;

	/* Enable SERR and parity checking */
	pci_cfg_read16(phb, bdfn, PCI_CFG_CMD, &val16);
	val16 |= (PCI_CFG_CMD_PERR_RESP |
		  PCI_CFG_CMD_SERR_EN);
	pci_cfg_write16(phb, bdfn, PCI_CFG_CMD, val16);

	/* Enable reporting various errors */
	if (!ecap) return;
	pci_cfg_read16(phb, bdfn, ecap + PCICAP_EXP_DEVCTL, &val16);
	val16 &= ~PCICAP_EXP_DEVCTL_CE_REPORT;
	val16 |= (PCICAP_EXP_DEVCTL_NFE_REPORT |
		  PCICAP_EXP_DEVCTL_FE_REPORT |
		  PCICAP_EXP_DEVCTL_UR_REPORT);

	/* Enable ECRC generation and check */
	pci_cfg_read32(phb, bdfn, aercap + PCIECAP_AER_CAPCTL, &val32);
	val32 |= (PCIECAP_AER_CAPCTL_ECRCG_EN |
		  PCIECAP_AER_CAPCTL_ECRCC_EN);
	pci_cfg_write32(phb, bdfn, aercap + PCIECAP_AER_CAPCTL, val32);
}

static int64_t phb4_pcicfg_no_dstate(void *dev,
				     struct pci_cfg_reg_filter *pcrf,
				     uint32_t offset, uint32_t len,
				     uint32_t *data,  bool write)
{
	uint32_t loff = offset - pcrf->start;

	/* Disable D-state change on children of the PHB. For now we
	 * simply block all writes to the PM control/status
	 */
	if (write && loff >= 4 && loff < 6)
		return OPAL_SUCCESS;

	return OPAL_PARTIAL;
}

static void phb4_check_device_quirks(struct phb *phb, struct pci_device *dev)
{
	/* Some special adapter tweaks for devices directly under the PHB */
	if (dev->primary_bus != 1)
		return;

	/* PM quirk */
	if (!pci_has_cap(dev, PCI_CFG_CAP_ID_PM, false))
		return;

	pci_add_cfg_reg_filter(dev,
			       pci_cap(dev, PCI_CFG_CAP_ID_PM, false), 8,
			       PCI_REG_FLAG_WRITE,
			       phb4_pcicfg_no_dstate);
}

static int phb4_device_init(struct phb *phb, struct pci_device *dev,
			    void *data __unused)
{
	int ecap, aercap;

	/* Setup special device quirks */
	phb4_check_device_quirks(phb, dev);

	/* Common initialization for the device */
	pci_device_init(phb, dev);

	ecap = pci_cap(dev, PCI_CFG_CAP_ID_EXP, false);
	aercap = pci_cap(dev, PCIECAP_ID_AER, true);
	if (dev->dev_type == PCIE_TYPE_ROOT_PORT)
		phb4_root_port_init(phb, dev, ecap, aercap);
	else if (dev->dev_type == PCIE_TYPE_SWITCH_UPPORT ||
		 dev->dev_type == PCIE_TYPE_SWITCH_DNPORT)
		phb4_switch_port_init(phb, dev, ecap, aercap);
	else
		phb4_endpoint_init(phb, dev, ecap, aercap);

	return 0;
}

static int64_t phb4_pci_reinit(struct phb *phb, uint64_t scope, uint64_t data)
{
	struct pci_device *pd;
	uint16_t bdfn = data;
	int ret;

	if (scope != OPAL_REINIT_PCI_DEV)
		return OPAL_PARAMETER;

	pd = pci_find_dev(phb, bdfn);
	if (!pd)
		return OPAL_PARAMETER;

	ret = phb4_device_init(phb, pd, NULL);
	if (ret)
		return OPAL_HARDWARE;

	return OPAL_SUCCESS;
}

/* Default value for MBT0, see comments in init_ioda_cache() */
static uint64_t phb4_default_mbt0(struct phb4 *p, unsigned int bar_idx)
{
	uint64_t mbt0;

	if (p->rev == PHB4_REV_NIMBUS_DD10) {
		mbt0 = SETFIELD(IODA3_MBT0_MODE, 0ull, IODA3_MBT0_MODE_MDT);
		if (bar_idx == 0)
			mbt0 |= SETFIELD(IODA3_MBT0_MDT_COLUMN, 0ull, 0);
		else
			mbt0 |= SETFIELD(IODA3_MBT0_MDT_COLUMN, 0ull, 1);
	} else {
		switch (p->mbt_size - bar_idx - 1) {
		case 0:
			mbt0 = SETFIELD(IODA3_MBT0_MODE, 0ull, IODA3_MBT0_MODE_MDT);
			mbt0 = SETFIELD(IODA3_MBT0_MDT_COLUMN, mbt0, 0);
			break;
		case 1:
			mbt0 = SETFIELD(IODA3_MBT0_MODE, 0ull, IODA3_MBT0_MODE_MDT);
			mbt0 = SETFIELD(IODA3_MBT0_MDT_COLUMN, mbt0, 1);
			break;
		case 2:
			mbt0 = SETFIELD(IODA3_MBT0_MODE, 0ull, IODA3_MBT0_MODE_MDT);
			mbt0 = SETFIELD(IODA3_MBT0_MDT_COLUMN, mbt0, 2);
			break;
		case 3:
			mbt0 = SETFIELD(IODA3_MBT0_MODE, 0ull, IODA3_MBT0_MODE_MDT);
			mbt0 = SETFIELD(IODA3_MBT0_MDT_COLUMN, mbt0, 3);
			break;
		default:
			mbt0 = SETFIELD(IODA3_MBT0_MODE, 0ull, IODA3_MBT0_MODE_PE_SEG);
		}
	}
	return mbt0;
}

/* Clear IODA cache tables */
static void phb4_init_ioda_cache(struct phb4 *p)
{
	uint32_t i;

	/*
	 * RTT and PELTV. RTE should be 0xFF's to indicate
	 * invalid PE# for the corresponding RID.
	 *
	 * Note: Instead we set all RTE entries to 0x00 to
	 * work around a problem where PE lookups might be
	 * done before Linux has established valid PE's
	 * (during PCI probing). We can revisit that once/if
	 * Linux has been fixed to always setup valid PEs.
	 *
	 * The value 0x00 corresponds to the default PE# Linux
	 * uses to check for config space freezes before it
	 * has assigned PE# to busses.
	 *
	 * WARNING: Additionally, we need to be careful, there's
	 * a HW issue, if we get an MSI on an RTT entry that is
	 * FF, things will go bad. We need to ensure we don't
	 * ever let a live FF RTT even temporarily when resetting
	 * for EEH etc... (HW278969).
	 */
	for (i = 0; i < ARRAY_SIZE(p->rte_cache); i++)
		p->rte_cache[i] = PHB4_RESERVED_PE_NUM(p);
	memset(p->peltv_cache, 0x0,  sizeof(p->peltv_cache));
	memset(p->tve_cache, 0x0, sizeof(p->tve_cache));

	/* XXX Should we mask them ? */
	memset(p->mist_cache, 0x0, sizeof(p->mist_cache));

	/* Configure MBT entries 1...N */
	if (p->rev == PHB4_REV_NIMBUS_DD10) {
		/* Since we configure the DD1.0 PHB4 with half the PE's,
		 * we need to give the illusion that we support only
		 * 128/256 segments half the segments.
		 *
		 * To achieve that, we configure *all* the M64 windows to use
		 * column 1 of the MDT, which is itself set so that segment 0
		 * and 1 map to PE0, 2 and 3 to PE1 etc...
		 *
		 * Column 0, 2 and 3 are left all 0, column 0 will be used for
		 * M32 and configured by the OS.
		 */
		for (i = 0; i < p->max_num_pes; i++)
			p->mdt_cache[i] = SETFIELD(IODA3_MDT_PE_B, 0ull, i >> 1);

	} else {
		/* On DD2.0 we don't have the above problem. We still use MDT
		 * column 1..3 for the last 3 BARs however, thus allowing Linux
		 * to remap those, and setup all the other ones for now in mode 00
		 * (segment# == PE#). By default those columns are set to map
		 * the same way.
		 */
		for (i = 0; i < p->max_num_pes; i++) {
			p->mdt_cache[i]  = SETFIELD(IODA3_MDT_PE_B, 0ull, i);
			p->mdt_cache[i] |= SETFIELD(IODA3_MDT_PE_C, 0ull, i);
			p->mdt_cache[i] |= SETFIELD(IODA3_MDT_PE_D, 0ull, i);
		}

	}
	for (i = 0; i < p->mbt_size; i++) {
		p->mbt_cache[i][0] = phb4_default_mbt0(p, i);
		p->mbt_cache[i][1] = 0;
	}

	/* Initialise M32 bar using MDT entry 0 */
	p->mbt_cache[0][0] |= IODA3_MBT0_TYPE_M32 |
		(p->mm1_base & IODA3_MBT0_BASE_ADDR);
	p->mbt_cache[0][1] = IODA3_MBT1_ENABLE |
		((~(M32_PCI_SIZE - 1)) & IODA3_MBT1_MASK);
}

static int64_t phb4_wait_bit(struct phb4 *p, uint32_t reg,
			     uint64_t mask, uint64_t want_val)
{
	uint64_t val;

	/* Wait for all pending TCE kills to complete
	 *
	 * XXX Add timeout...
	 */
	/* XXX SIMICS is nasty... */
	if ((reg == PHB_TCE_KILL || reg == PHB_DMARD_SYNC) &&
	    chip_quirk(QUIRK_SIMICS))
		return OPAL_SUCCESS;

	for (;;) {
		val = in_be64(p->regs + reg);
		if (val == 0xffffffffffffffffull) {
			/* XXX Fenced ? */
			return OPAL_HARDWARE;
		}
		if ((val & mask) == want_val)
			break;

	}
	return OPAL_SUCCESS;
}

static int64_t phb4_tce_kill(struct phb *phb, uint32_t kill_type,
			     uint64_t pe_number, uint32_t tce_size,
			     uint64_t dma_addr, uint32_t npages)
{
	struct phb4 *p = phb_to_phb4(phb);
	uint64_t val;
	int64_t rc;

	sync();
	switch(kill_type) {
	case OPAL_PCI_TCE_KILL_PAGES:
		while (npages--) {
			/* Wait for a slot in the HW kill queue */
			rc = phb4_wait_bit(p, PHB_TCE_KILL,
					   PHB_TCE_KILL_ALL |
					   PHB_TCE_KILL_PE |
					   PHB_TCE_KILL_ONE, 0);
			if (rc)
				return rc;
			val = SETFIELD(PHB_TCE_KILL_PENUM, dma_addr, pe_number);

			/* Set appropriate page size */
			switch(tce_size) {
			case 0x1000:
				if (dma_addr & 0xf000000000000fffull)
					return OPAL_PARAMETER;
				break;
			case 0x10000:
				if (dma_addr & 0xf00000000000ffffull)
					return OPAL_PARAMETER;
				val |= PHB_TCE_KILL_PSEL | PHB_TCE_KILL_64K;
				break;
			case 0x200000:
				if (dma_addr & 0xf0000000001fffffull)
					return OPAL_PARAMETER;
				val |= PHB_TCE_KILL_PSEL | PHB_TCE_KILL_2M;
				break;
			case 0x40000000:
				if (dma_addr & 0xf00000003fffffffull)
					return OPAL_PARAMETER;
				val |= PHB_TCE_KILL_PSEL | PHB_TCE_KILL_1G;
				break;
			default:
				return OPAL_PARAMETER;
			}
			/* Perform kill */
			out_be64(p->regs + PHB_TCE_KILL, PHB_TCE_KILL_ONE | val);
			/* Next page */
			dma_addr += tce_size;
		}
		break;
	case OPAL_PCI_TCE_KILL_PE:
		/* Wait for a slot in the HW kill queue */
		rc = phb4_wait_bit(p, PHB_TCE_KILL,
				   PHB_TCE_KILL_ALL |
				   PHB_TCE_KILL_PE |
				   PHB_TCE_KILL_ONE, 0);
		if (rc)
			return rc;
		/* Perform kill */
		out_be64(p->regs + PHB_TCE_KILL, PHB_TCE_KILL_PE |
			 SETFIELD(PHB_TCE_KILL_PENUM, 0ull, pe_number));
		break;
	case OPAL_PCI_TCE_KILL_ALL:
		/* Wait for a slot in the HW kill queue */
		rc = phb4_wait_bit(p, PHB_TCE_KILL,
				   PHB_TCE_KILL_ALL |
				   PHB_TCE_KILL_PE |
				   PHB_TCE_KILL_ONE, 0);
		if (rc)
			return rc;
		/* Perform kill */
		out_be64(p->regs + PHB_TCE_KILL, PHB_TCE_KILL_ALL);
		break;
	default:
		return OPAL_PARAMETER;
	}

	/* Start DMA sync process */
	out_be64(p->regs + PHB_DMARD_SYNC, PHB_DMARD_SYNC_START);

	/* Wait for kill to complete */
	rc = phb4_wait_bit(p, PHB_Q_DMA_R, PHB_Q_DMA_R_TCE_KILL_STATUS, 0);
	if (rc)
		return rc;

	/* Wait for DMA sync to complete */
	return phb4_wait_bit(p, PHB_DMARD_SYNC,
			     PHB_DMARD_SYNC_COMPLETE,
			     PHB_DMARD_SYNC_COMPLETE);
}

/* phb4_ioda_reset - Reset the IODA tables
 *
 * @purge: If true, the cache is cleared and the cleared values
 *         are applied to HW. If false, the cached values are
 *         applied to HW
 *
 * This reset the IODA tables in the PHB. It is called at
 * initialization time, on PHB reset, and can be called
 * explicitly from OPAL
 */
static int64_t phb4_ioda_reset(struct phb *phb, bool purge)
{
	struct phb4 *p = phb_to_phb4(phb);
	uint32_t i;
	uint64_t val;

	if (purge) {
		PHBDBG(p, "Purging all IODA tables...\n");
		if (phb->slot)
			phb->slot->link_retries = PHB4_LINK_LINK_RETRIES;
		phb4_init_ioda_cache(p);
	}

	/* Init_30..31 - Errata workaround, clear PESTA entry 0 */
	phb4_ioda_sel(p, IODA3_TBL_PESTA, 0, false);
	out_be64(p->regs + PHB_IODA_DATA0, 0);

	/* Init_32..33 - MIST  */
	phb4_ioda_sel(p, IODA3_TBL_MIST, 0, true);
	val = in_be64(p->regs + PHB_IODA_ADDR);
	val = SETFIELD(PHB_IODA_AD_MIST_PWV, val, 0xf);
	out_be64(p->regs + PHB_IODA_ADDR, val);
	for (i = 0; i < (p->num_irqs/4); i++)
		out_be64(p->regs + PHB_IODA_DATA0, p->mist_cache[i]);

	/* Init_34..35 - MRT */
	phb4_ioda_sel(p, IODA3_TBL_MRT, 0, true);
	for (i = 0; i < p->mrt_size; i++)
		out_be64(p->regs + PHB_IODA_DATA0, 0);

	/* Init_36..37 - TVT */
	phb4_ioda_sel(p, IODA3_TBL_TVT, 0, true);
	for (i = 0; i < p->tvt_size; i++)
		out_be64(p->regs + PHB_IODA_DATA0, p->tve_cache[i]);

	/* Init_38..39 - MBT */
	phb4_ioda_sel(p, IODA3_TBL_MBT, 0, true);
	for (i = 0; i < p->mbt_size; i++) {
		out_be64(p->regs + PHB_IODA_DATA0, p->mbt_cache[i][0]);
		out_be64(p->regs + PHB_IODA_DATA0, p->mbt_cache[i][1]);
	}

	/* Init_40..41 - MDT */
	phb4_ioda_sel(p, IODA3_TBL_MDT, 0, true);
	for (i = 0; i < p->max_num_pes; i++)
		out_be64(p->regs + PHB_IODA_DATA0, p->mdt_cache[i]);

	/* Additional OPAL specific inits */

	/* Clear RTT and PELTV and PEST */
	if (p->tbl_rtt)
		memcpy((void *)p->tbl_rtt, p->rte_cache, RTT_TABLE_SIZE);
	if (p->tbl_peltv)
		memcpy((void *)p->tbl_peltv, p->peltv_cache, p->tbl_peltv_size);

	/* Clear PEST & PEEV */
	for (i = 0; i < p->max_num_pes; i++) {
		phb4_ioda_sel(p, IODA3_TBL_PESTA, i, false);
		out_be64(p->regs + PHB_IODA_DATA0, 0);
		phb4_ioda_sel(p, IODA3_TBL_PESTB, i, false);
		out_be64(p->regs + PHB_IODA_DATA0, 0);
	}

	phb4_ioda_sel(p, IODA3_TBL_PEEV, 0, true);
	for (i = 0; i < p->max_num_pes/64; i++)
		out_be64(p->regs + PHB_IODA_DATA0, 0);

	/* Invalidate RTE, TCE cache */
	out_be64(p->regs + PHB_RTC_INVALIDATE, PHB_RTC_INVALIDATE_ALL);

	return phb4_tce_kill(&p->phb, OPAL_PCI_TCE_KILL_ALL, 0, 0, 0, 0);
}

/*
 * Clear anything we have in PAPR Error Injection registers. Though
 * the spec says the PAPR error injection should be one-shot without
 * the "sticky" bit. However, that's false according to the experiments
 * I had. So we have to clear it at appropriate point in kernel to
 * avoid endless frozen PE.
 */
static int64_t phb4_papr_errinjct_reset(struct phb *phb)
{
	struct phb4 *p = phb_to_phb4(phb);

	out_be64(p->regs + PHB_PAPR_ERR_INJ_CTL, 0x0ul);
	out_be64(p->regs + PHB_PAPR_ERR_INJ_ADDR, 0x0ul);
	out_be64(p->regs + PHB_PAPR_ERR_INJ_MASK, 0x0ul);

	return OPAL_SUCCESS;
}

static int64_t phb4_set_phb_mem_window(struct phb *phb,
				       uint16_t window_type,
				       uint16_t window_num,
				       uint64_t addr,
				       uint64_t pci_addr,
				       uint64_t size)
{
	struct phb4 *p = phb_to_phb4(phb);
	uint64_t mbt0, mbt1;

	/*
	 * We have a unified MBT for all BARs on PHB4. However we
	 * also have a current limitation that only half of the PEs
	 * are available (in order to have 2 TVT entries per PE)
	 * on DD1.0
	 *
	 * So we use it as follow:
	 *
	 *  - M32 is hard wired to be MBT[0] and uses MDT column 0
	 *    for remapping.
	 *
	 *  - MBT[1..n] are available to the OS, currently only as
	 *    fully segmented or single PE (we don't yet expose the
	 *    new segmentation modes).
	 *
	 *  - [DD1.0] In order to deal with the above PE# limitations, since
	 *    the OS assumes the segmentation is done with as many
	 *    segments as PEs, we effectively fake it by mapping all
	 *    MBT[1..n] to NDT column 1 which has been configured to
	 *    give 2 adjacent segments the same PE# (see comment in
	 *    ioda cache init). We don't expose the other columns to
	 *    the OS.
	 *
	 *  - [DD2.0] We configure the 3 last BARs to columnt 1..3
	 *    initially set to segment# == PE#. We will need to provide some
	 *    extensions to the existing APIs to enable remapping of
	 *    segments on those BARs (and only those) as the current
	 *    API forces single segment mode.
	 */
	switch (window_type) {
	case OPAL_IO_WINDOW_TYPE:
	case OPAL_M32_WINDOW_TYPE:
		return OPAL_UNSUPPORTED;
	case OPAL_M64_WINDOW_TYPE:
		if (window_num == 0 || window_num >= p->mbt_size) {
			PHBERR(p, "%s: Invalid window %d\n",
			       __func__, window_num);
			return OPAL_PARAMETER;
		}

		mbt0 = p->mbt_cache[window_num][0];
		mbt1 = p->mbt_cache[window_num][1];

		/* XXX For now we assume the 4K minimum alignment,
		 * todo: check with the HW folks what the exact limits
		 * are based on the segmentation model.
		 */
		if ((addr & 0xFFFul) || (size & 0xFFFul)) {
			PHBERR(p, "%s: Bad addr/size alignment %llx/%llx\n",
			       __func__, addr, size);
			return OPAL_PARAMETER;
		}

		/* size should be 2^N */
		if (!size || size & (size-1)) {
			PHBERR(p, "%s: size not a power of 2: %llx\n",
			       __func__,  size);
			return OPAL_PARAMETER;
		}

		/* address should be size aligned */
		if (addr & (size - 1)) {
			PHBERR(p, "%s: addr not size aligned %llx/%llx\n",
			       __func__, addr, size);
			return OPAL_PARAMETER;
		}

		break;
	default:
		return OPAL_PARAMETER;
	}

	/* The BAR shouldn't be enabled yet */
	if (mbt0 & IODA3_MBT0_ENABLE)
		return OPAL_PARTIAL;

	/* Apply the settings */
	mbt0 = SETFIELD(IODA3_MBT0_BASE_ADDR, mbt0, addr >> 12);
	mbt1 = SETFIELD(IODA3_MBT1_MASK, mbt1, ~((size >> 12) -1));
	p->mbt_cache[window_num][0] = mbt0;
	p->mbt_cache[window_num][1] = mbt1;

	return OPAL_SUCCESS;
}

/*
 * For one specific M64 BAR, it can be shared by all PEs,
 * or owned by single PE exclusively.
 */
static int64_t phb4_phb_mmio_enable(struct phb __unused *phb,
				    uint16_t window_type,
				    uint16_t window_num,
				    uint16_t enable)
{
	struct phb4 *p = phb_to_phb4(phb);
	uint64_t mbt0, mbt1, base, mask;

	/*
	 * By design, PHB4 doesn't support IODT any more.
	 * Besides, we can't enable M32 BAR as well. So
	 * the function is used to do M64 mapping and each
	 * BAR is supposed to be shared by all PEs.
	 *
	 * TODO: Add support for some of the new PHB4 split modes
	 */
	switch (window_type) {
	case OPAL_IO_WINDOW_TYPE:
	case OPAL_M32_WINDOW_TYPE:
		return OPAL_UNSUPPORTED;
	case OPAL_M64_WINDOW_TYPE:
		/* Window 0 is reserved for M32 */
		if (window_num == 0 || window_num >= p->mbt_size ||
		    enable > OPAL_ENABLE_M64_NON_SPLIT) {
			PHBDBG(p,
			       "phb4_phb_mmio_enable wrong args (window %d enable %d)\n",
			       window_num, enable);
			return OPAL_PARAMETER;
		}
		break;
	default:
		return OPAL_PARAMETER;
	}

	/*
	 * We need check the base/mask while enabling
	 * the M64 BAR. Otherwise, invalid base/mask
	 * might cause fenced AIB unintentionally
	 */
	mbt0 = p->mbt_cache[window_num][0];
	mbt1 = p->mbt_cache[window_num][1];

	if (enable == OPAL_DISABLE_M64) {
		/* Reset the window to disabled & default mode */
		mbt0 = phb4_default_mbt0(p, window_num);
		mbt1 = 0;
	} else {
		/* Verify that the mode is valid and consistent */
		if (enable == OPAL_ENABLE_M64_SPLIT) {
			uint64_t mode = GETFIELD(IODA3_MBT0_MODE, mbt0);
			if (mode != IODA3_MBT0_MODE_PE_SEG &&
			    mode != IODA3_MBT0_MODE_MDT)
				return OPAL_PARAMETER;
		} else if (enable == OPAL_ENABLE_M64_NON_SPLIT) {
			if (GETFIELD(IODA3_MBT0_MODE, mbt0) !=
			    IODA3_MBT0_MODE_SINGLE_PE)
				return OPAL_PARAMETER;
		} else
			return OPAL_PARAMETER;

		base = GETFIELD(IODA3_MBT0_BASE_ADDR, mbt0);
		base = (base << 12);
		mask = GETFIELD(IODA3_MBT1_MASK, mbt1);
		if (base < p->mm0_base || !mask)
			return OPAL_PARTIAL;

		mbt0 |= IODA3_MBT0_ENABLE;
		mbt1 |= IODA3_MBT1_ENABLE;
	}

	/* Update HW and cache */
	p->mbt_cache[window_num][0] = mbt0;
	p->mbt_cache[window_num][1] = mbt1;
	phb4_ioda_sel(p, IODA3_TBL_MBT, window_num << 1, true);
	out_be64(p->regs + PHB_IODA_DATA0, mbt0);
	out_be64(p->regs + PHB_IODA_DATA0, mbt1);

	return OPAL_SUCCESS;
}

static int64_t phb4_map_pe_mmio_window(struct phb *phb,
				       uint64_t pe_number,
				       uint16_t window_type,
				       uint16_t window_num,
				       uint16_t segment_num)
{
	struct phb4 *p = phb_to_phb4(phb);
	uint64_t mbt0, mbt1, mdt0, mdt1;

	if (pe_number >= p->num_pes)
		return OPAL_PARAMETER;

	/*
	 * We support a combined MDT that has 4 columns. We let the OS
	 * use kernel 0 for M32.
	 *
	 * On DD1.0 we configure column1 ourselves to handle the "half PEs"
	 * problem and thus simulate having a smaller number of segments.
	 * columns 2 and 3 unused.
	 *
	 * On DD2.0 we configure the 3 last BARs to map column 3..1 which
	 * by default are set to map segment# == pe#, but can be remapped
	 * here if we extend this function.
	 *
	 * The problem is that the current API was "hijacked" so that an
	 * attempt at remapping any segment of an M64 has the effect of
	 * turning it into a single-PE mode BAR. So if we want to support
	 * remapping we'll have to play around this for example by creating
	 * a new API or a new window type...
	 */
	switch(window_type) {
	case OPAL_IO_WINDOW_TYPE:
		return OPAL_UNSUPPORTED;
	case OPAL_M32_WINDOW_TYPE:
		if (window_num != 0 || segment_num >= p->num_pes)
			return OPAL_PARAMETER;

		if (p->rev == PHB4_REV_NIMBUS_DD10) {
			mdt0 = p->mdt_cache[segment_num << 1];
			mdt1 = p->mdt_cache[(segment_num << 1) + 1];
			mdt0 = SETFIELD(IODA3_MDT_PE_A, mdt0, pe_number);
			mdt1 = SETFIELD(IODA3_MDT_PE_A, mdt1, pe_number);
			p->mdt_cache[segment_num << 1] = mdt0;
			p->mdt_cache[(segment_num << 1) + 1] = mdt1;
			phb4_ioda_sel(p, IODA3_TBL_MDT, segment_num << 1, true);
			out_be64(p->regs + PHB_IODA_DATA0, mdt0);
			out_be64(p->regs + PHB_IODA_DATA0, mdt1);
		} else {
			mdt0 = p->mdt_cache[segment_num];
			mdt0 = SETFIELD(IODA3_MDT_PE_A, mdt0, pe_number);
			phb4_ioda_sel(p, IODA3_TBL_MDT, segment_num, false);
			out_be64(p->regs + PHB_IODA_DATA0, mdt0);
		}
		break;
	case OPAL_M64_WINDOW_TYPE:
		if (window_num == 0 || window_num >= p->mbt_size)
			return OPAL_PARAMETER;

		mbt0 = p->mbt_cache[window_num][0];
		mbt1 = p->mbt_cache[window_num][1];

		/* The BAR shouldn't be enabled yet */
		if (mbt0 & IODA3_MBT0_ENABLE)
			return OPAL_PARTIAL;

		/* Set to single PE mode and configure the PE */
		mbt0 = SETFIELD(IODA3_MBT0_MODE, mbt0,
				IODA3_MBT0_MODE_SINGLE_PE);
		mbt1 = SETFIELD(IODA3_MBT1_SINGLE_PE_NUM, mbt1, pe_number);
		p->mbt_cache[window_num][0] = mbt0;
		p->mbt_cache[window_num][1] = mbt1;
		break;
	default:
		return OPAL_PARAMETER;
	}

	return OPAL_SUCCESS;
}

static int64_t phb4_map_pe_dma_window(struct phb *phb,
				      uint64_t pe_number,
				      uint16_t window_id,
				      uint16_t tce_levels,
				      uint64_t tce_table_addr,
				      uint64_t tce_table_size,
				      uint64_t tce_page_size)
{
	struct phb4 *p = phb_to_phb4(phb);
	uint64_t tts_encoded;
	uint64_t data64 = 0;

	/*
	 * We configure the PHB in 2 TVE per PE mode to match phb3.
	 * Current Linux implementation *requires* the two windows per
	 * PE.
	 *
	 * Note: On DD2.0 this is the normal mode of operation.
	 */

	/*
	 * Sanity check. We currently only support "2 window per PE" mode
	 * ie, only bit 59 of the PCI address is used to select the window
	 */
	if (pe_number >= p->num_pes || (window_id >> 1) != pe_number)
		return OPAL_PARAMETER;

	/*
	 * tce_table_size == 0 is used to disable an entry, in this case
	 * we ignore other arguments
	 */
	if (tce_table_size == 0) {
		phb4_ioda_sel(p, IODA3_TBL_TVT, window_id, false);
		out_be64(p->regs + PHB_IODA_DATA0, 0);
		p->tve_cache[window_id] = 0;
		return OPAL_SUCCESS;
	}

	/* Additional arguments validation */
	if (tce_levels < 1 || tce_levels > 5 ||
	    !is_pow2(tce_table_size) ||
	    tce_table_size < 0x1000)
		return OPAL_PARAMETER;

	/* Encode TCE table size */
	data64 = SETFIELD(IODA3_TVT_TABLE_ADDR, 0ul, tce_table_addr >> 12);
	tts_encoded = ilog2(tce_table_size) - 11;
	if (tts_encoded > 31)
		return OPAL_PARAMETER;
	data64 = SETFIELD(IODA3_TVT_TCE_TABLE_SIZE, data64, tts_encoded);

	/* Encode TCE page size */
	switch (tce_page_size) {
	case 0x1000:	/* 4K */
		data64 = SETFIELD(IODA3_TVT_IO_PSIZE, data64, 1);
		break;
	case 0x10000:	/* 64K */
		data64 = SETFIELD(IODA3_TVT_IO_PSIZE, data64, 5);
		break;
	case 0x1000000:	/* 16M */
		data64 = SETFIELD(IODA3_TVT_IO_PSIZE, data64, 13);
		break;
	case 0x10000000: /* 256M */
		data64 = SETFIELD(IODA3_TVT_IO_PSIZE, data64, 17);
		break;
	default:
		return OPAL_PARAMETER;
	}

	/* Encode number of levels */
	data64 = SETFIELD(IODA3_TVT_NUM_LEVELS, data64, tce_levels - 1);

	phb4_ioda_sel(p, IODA3_TBL_TVT, window_id, false);
	out_be64(p->regs + PHB_IODA_DATA0, data64);
	p->tve_cache[window_id] = data64;

	return OPAL_SUCCESS;
}

static int64_t phb4_map_pe_dma_window_real(struct phb *phb,
					   uint64_t pe_number,
					   uint16_t window_id,
					   uint64_t pci_start_addr,
					   uint64_t pci_mem_size)
{
	struct phb4 *p = phb_to_phb4(phb);
	uint64_t end = pci_start_addr + pci_mem_size;
	uint64_t tve;

	if (pe_number >= p->num_pes ||
	    (window_id >> 1) != pe_number)
		return OPAL_PARAMETER;

	if (pci_mem_size) {
		/* Enable */

		/*
		 * Check that the start address has the right TVE index,
		 * we only support the 1 bit mode where each PE has 2
		 * TVEs
		 */
		if ((pci_start_addr >> 59) != (window_id & 1))
			return OPAL_PARAMETER;
		pci_start_addr &= ((1ull << 59) - 1);
		end = pci_start_addr + pci_mem_size;

		/* We have to be 16M aligned */
		if ((pci_start_addr & 0x00ffffff) ||
		    (pci_mem_size & 0x00ffffff))
			return OPAL_PARAMETER;

		/*
		 * It *looks* like this is the max we can support (we need
		 * to verify this. Also we are not checking for rollover,
		 * but then we aren't trying too hard to protect ourselves
		 * againt a completely broken OS.
		 */
		if (end > 0x0003ffffffffffffull)
			return OPAL_PARAMETER;

		/*
		 * Put start address bits 49:24 into TVE[52:53]||[0:23]
		 * and end address bits 49:24 into TVE[54:55]||[24:47]
		 * and set TVE[51]
		 */
		tve  = (pci_start_addr << 16) & (0xffffffull << 40);
		tve |= (pci_start_addr >> 38) & (3ull << 10);
		tve |= (end >>  8) & (0xfffffful << 16);
		tve |= (end >> 40) & (3ull << 8);
		tve |= PPC_BIT(51) | IODA3_TVT_NON_TRANSLATE_50;
	} else {
		/* Disable */
		tve = 0;
	}

	phb4_ioda_sel(p, IODA3_TBL_TVT, window_id, false);
	out_be64(p->regs + PHB_IODA_DATA0, tve);
	p->tve_cache[window_id] = tve;

	return OPAL_SUCCESS;
}

static int64_t phb4_set_ive_pe(struct phb *phb,
			       uint64_t pe_number,
			       uint32_t ive_num)
{
	struct phb4 *p = phb_to_phb4(phb);
	uint32_t mist_idx;
	uint32_t mist_quad;
	uint32_t mist_shift;
	uint64_t val;

	if (pe_number >= p->num_pes || ive_num >= (p->num_irqs - 8))
		return OPAL_PARAMETER;

	mist_idx = ive_num >> 2;
	mist_quad = ive_num & 3;
	mist_shift = (3 - mist_quad) << 4;
	p->mist_cache[mist_idx] &= ~(0x0fffull << mist_shift);
	p->mist_cache[mist_idx] |=  ((uint64_t)pe_number) << mist_shift;

	/* Note: This has the side effect of clearing P/Q, so this
	 * shouldn't be called while the interrupt is "hot"
	 */

	phb4_ioda_sel(p, IODA3_TBL_MIST, mist_idx, false);

	/* We need to inject the appropriate MIST write enable bit
	 * in the IODA table address register
	 */
	val = in_be64(p->regs + PHB_IODA_ADDR);
	val = SETFIELD(PHB_IODA_AD_MIST_PWV, val, 8 >> mist_quad);
	out_be64(p->regs + PHB_IODA_ADDR, val);

	/* Write entry */
	out_be64(p->regs + PHB_IODA_DATA0, p->mist_cache[mist_idx]);

	return OPAL_SUCCESS;
}

static int64_t phb4_get_msi_32(struct phb *phb,
			       uint64_t pe_number,
			       uint32_t ive_num,
			       uint8_t msi_range,
			       uint32_t *msi_address,
			       uint32_t *message_data)
{
	struct phb4 *p = phb_to_phb4(phb);

	/*
	 * Sanity check. We needn't check on mve_number (PE#)
	 * on PHB3 since the interrupt source is purely determined
	 * by its DMA address and data, but the check isn't
	 * harmful.
	 */
	if (pe_number >= p->num_pes ||
	    ive_num >= (p->num_irqs - 8) ||
	    msi_range != 1 || !msi_address|| !message_data)
		return OPAL_PARAMETER;

	/*
	 * DMA address and data will form the IVE index.
	 * For more details, please refer to IODA2 spec.
	 */
	*msi_address = 0xFFFF0000 | ((ive_num << 4) & 0xFFFFFE0F);
	*message_data = ive_num & 0x1F;

	return OPAL_SUCCESS;
}

static int64_t phb4_get_msi_64(struct phb *phb,
			       uint64_t pe_number,
			       uint32_t ive_num,
			       uint8_t msi_range,
			       uint64_t *msi_address,
			       uint32_t *message_data)
{
	struct phb4 *p = phb_to_phb4(phb);

	/* Sanity check */
	if (pe_number >= p->num_pes ||
	    ive_num >= (p->num_irqs - 8) ||
	    msi_range != 1 || !msi_address || !message_data)
		return OPAL_PARAMETER;

	/*
	 * DMA address and data will form the IVE index.
	 * For more details, please refer to IODA2 spec.
	 */
	*msi_address = (0x1ul << 60) | ((ive_num << 4) & 0xFFFFFFFFFFFFFE0Ful);
	*message_data = ive_num & 0x1F;

	return OPAL_SUCCESS;
}

static void phb4_rc_err_clear(struct phb4 *p)
{
	/* Init_47 - Clear errors */
	phb4_pcicfg_write16(&p->phb, 0, PCI_CFG_SECONDARY_STATUS, 0xffff);

	if (p->ecap <= 0)
		return;

	phb4_pcicfg_write16(&p->phb, 0, p->ecap + PCICAP_EXP_DEVSTAT,
			     PCICAP_EXP_DEVSTAT_CE	|
			     PCICAP_EXP_DEVSTAT_NFE	|
			     PCICAP_EXP_DEVSTAT_FE	|
			     PCICAP_EXP_DEVSTAT_UE);

	if (p->aercap <= 0)
		return;

	/* Clear all UE status */
	phb4_pcicfg_write32(&p->phb, 0, p->aercap + PCIECAP_AER_UE_STATUS,
			     0xffffffff);
	/* Clear all CE status */
	phb4_pcicfg_write32(&p->phb, 0, p->aercap + PCIECAP_AER_CE_STATUS,
			     0xffffffff);
	/* Clear root error status */
	phb4_pcicfg_write32(&p->phb, 0, p->aercap + PCIECAP_AER_RERR_STA,
			     0xffffffff);
}

static void phb4_err_clear_regb(struct phb4 *p)
{
	uint64_t val64;

	val64 = phb4_read_reg(p, PHB_REGB_ERR_STATUS);
	phb4_write_reg(p, PHB_REGB_ERR_STATUS, val64);
	phb4_write_reg(p, PHB_REGB_ERR1_STATUS, 0x0ul);
	phb4_write_reg(p, PHB_REGB_ERR_LOG_0, 0x0ul);
	phb4_write_reg(p, PHB_REGB_ERR_LOG_1, 0x0ul);
}

/*
 * The function can be called during error recovery for all classes of
 * errors.  This is new to PHB4; previous revisions had separate
 * sequences for INF/ER/Fatal errors.
 *
 * "Rec #" in this function refer to "Recov_#" steps in the
 * PHB4 INF recovery sequence.
 */
static void phb4_err_clear(struct phb4 *p)
{
	uint64_t val64;
	uint64_t fir = phb4_read_reg(p, PHB_LEM_FIR_ACCUM);

	/* Rec 1: Acquire the PCI config lock (we don't need to do this) */

	/* Rec 2...15: Clear error status in RC config space */
	phb4_rc_err_clear(p);

	/* Rec 16...23: Clear PBL errors */
	val64 = phb4_read_reg(p, PHB_PBL_ERR_STATUS);
	phb4_write_reg(p, PHB_PBL_ERR_STATUS, val64);
	phb4_write_reg(p, PHB_PBL_ERR1_STATUS, 0x0ul);
	phb4_write_reg(p, PHB_PBL_ERR_LOG_0, 0x0ul);
	phb4_write_reg(p, PHB_PBL_ERR_LOG_1, 0x0ul);

	/* Rec 24...31: Clear REGB errors */
	phb4_err_clear_regb(p);

	/* Rec 32...59: Clear PHB error trap */
	val64 = phb4_read_reg(p, PHB_TXE_ERR_STATUS);
	phb4_write_reg(p, PHB_TXE_ERR_STATUS, val64);
	phb4_write_reg(p, PHB_TXE_ERR1_STATUS, 0x0ul);
	phb4_write_reg(p, PHB_TXE_ERR_LOG_0, 0x0ul);
	phb4_write_reg(p, PHB_TXE_ERR_LOG_1, 0x0ul);

	val64 = phb4_read_reg(p, PHB_RXE_ARB_ERR_STATUS);
	phb4_write_reg(p, PHB_RXE_ARB_ERR_STATUS, val64);
	phb4_write_reg(p, PHB_RXE_ARB_ERR1_STATUS, 0x0ul);
	phb4_write_reg(p, PHB_RXE_ARB_ERR_LOG_0, 0x0ul);
	phb4_write_reg(p, PHB_RXE_ARB_ERR_LOG_1, 0x0ul);

	val64 = phb4_read_reg(p, PHB_RXE_MRG_ERR_STATUS);
	phb4_write_reg(p, PHB_RXE_MRG_ERR_STATUS, val64);
	phb4_write_reg(p, PHB_RXE_MRG_ERR1_STATUS, 0x0ul);
	phb4_write_reg(p, PHB_RXE_MRG_ERR_LOG_0, 0x0ul);
	phb4_write_reg(p, PHB_RXE_MRG_ERR_LOG_1, 0x0ul);

	val64 = phb4_read_reg(p, PHB_RXE_TCE_ERR_STATUS);
	phb4_write_reg(p, PHB_RXE_TCE_ERR_STATUS, val64);
	phb4_write_reg(p, PHB_RXE_TCE_ERR1_STATUS, 0x0ul);
	phb4_write_reg(p, PHB_RXE_TCE_ERR_LOG_0, 0x0ul);
	phb4_write_reg(p, PHB_RXE_TCE_ERR_LOG_1, 0x0ul);

	val64 = phb4_read_reg(p, PHB_ERR_STATUS);
	phb4_write_reg(p, PHB_ERR_STATUS, val64);
	phb4_write_reg(p, PHB_ERR1_STATUS, 0x0ul);
	phb4_write_reg(p, PHB_ERR_LOG_0, 0x0ul);
	phb4_write_reg(p, PHB_ERR_LOG_1, 0x0ul);

	/* Rec 61/62: Clear FIR/WOF */
	phb4_write_reg(p, PHB_LEM_FIR_AND_MASK, ~fir);
	phb4_write_reg(p, PHB_LEM_WOF, 0x0ul);

	/* Rec 63: Update LEM mask to its initial value */
	phb4_write_reg(p, PHB_LEM_ERROR_MASK, 0x0ul);

	/* Rec 64: Clear the PCI config lock (we don't need to do this) */
}

static void phb4_read_phb_status(struct phb4 *p,
				 struct OpalIoPhb4ErrorData *stat)
{
	uint16_t val = 0;
	uint32_t i;
	uint64_t *pPEST;

	memset(stat, 0, sizeof(struct OpalIoPhb4ErrorData));

	/* Error data common part */
	stat->common.version = OPAL_PHB_ERROR_DATA_VERSION_1;
	stat->common.ioType  = OPAL_PHB_ERROR_DATA_TYPE_PHB4;
	stat->common.len     = sizeof(struct OpalIoPhb4ErrorData);

	/* Use ASB for config space if the PHB is fenced */
	if (p->flags & PHB4_AIB_FENCED)
		p->flags |= PHB4_CFG_USE_ASB;

	/* Grab RC bridge control, make it 32-bit */
	phb4_pcicfg_read16(&p->phb, 0, PCI_CFG_BRCTL, &val);
	stat->brdgCtl = val;

	/*
	 * Grab various RC PCIe capability registers. All device, slot
	 * and link status are 16-bit, so we grab the pair control+status
	 * for each of them
	 */
	phb4_pcicfg_read32(&p->phb, 0, p->ecap + PCICAP_EXP_DEVCTL,
			   &stat->deviceStatus);
	phb4_pcicfg_read32(&p->phb, 0, p->ecap + PCICAP_EXP_SLOTCTL,
			   &stat->slotStatus);
	phb4_pcicfg_read32(&p->phb, 0, p->ecap + PCICAP_EXP_LCTL,
			   &stat->linkStatus);

	 /*
	 * I assume those are the standard config space header, cmd & status
	 * together makes 32-bit. Secondary status is 16-bit so I'll clear
	 * the top on that one
	 */
	phb4_pcicfg_read32(&p->phb, 0, PCI_CFG_CMD, &stat->devCmdStatus);
	phb4_pcicfg_read16(&p->phb, 0, PCI_CFG_SECONDARY_STATUS, &val);
	stat->devSecStatus = val;

	/* Grab a bunch of AER regs */
	phb4_pcicfg_read32(&p->phb, 0, p->aercap + PCIECAP_AER_RERR_STA,
			   &stat->rootErrorStatus);
	phb4_pcicfg_read32(&p->phb, 0, p->aercap + PCIECAP_AER_UE_STATUS,
			   &stat->uncorrErrorStatus);
	phb4_pcicfg_read32(&p->phb, 0, p->aercap + PCIECAP_AER_CE_STATUS,
			   &stat->corrErrorStatus);
	phb4_pcicfg_read32(&p->phb, 0, p->aercap + PCIECAP_AER_HDR_LOG0,
			   &stat->tlpHdr1);
	phb4_pcicfg_read32(&p->phb, 0, p->aercap + PCIECAP_AER_HDR_LOG1,
			   &stat->tlpHdr2);
	phb4_pcicfg_read32(&p->phb, 0, p->aercap + PCIECAP_AER_HDR_LOG2,
			   &stat->tlpHdr3);
	phb4_pcicfg_read32(&p->phb, 0, p->aercap + PCIECAP_AER_HDR_LOG3,
			   &stat->tlpHdr4);
	phb4_pcicfg_read32(&p->phb, 0, p->aercap + PCIECAP_AER_SRCID,
			   &stat->sourceId);

	/* PEC NFIR, same as P8/PHB3 */
	xscom_read(p->chip_id, p->pe_stk_xscom + 0x0, &stat->nFir);
	xscom_read(p->chip_id, p->pe_stk_xscom + 0x3, &stat->nFirMask);
	xscom_read(p->chip_id, p->pe_stk_xscom + 0x8, &stat->nFirWOF);

	/* PHB4 inbound and outbound error Regs */
	stat->phbPlssr = phb4_read_reg_asb(p, PHB_CPU_LOADSTORE_STATUS);
	stat->phbCsr = phb4_read_reg_asb(p, PHB_DMA_CHAN_STATUS);
	stat->lemFir = phb4_read_reg_asb(p, PHB_LEM_FIR_ACCUM);
	stat->lemErrorMask = phb4_read_reg_asb(p, PHB_LEM_ERROR_MASK);
	stat->lemWOF = phb4_read_reg_asb(p, PHB_LEM_WOF);
	stat->phbErrorStatus = phb4_read_reg_asb(p, PHB_ERR_STATUS);
	stat->phbFirstErrorStatus = phb4_read_reg_asb(p, PHB_ERR1_STATUS);
	stat->phbErrorLog0 = phb4_read_reg_asb(p, PHB_ERR_LOG_0);
	stat->phbErrorLog1 = phb4_read_reg_asb(p, PHB_ERR_LOG_1);
	stat->phbTxeErrorStatus = phb4_read_reg_asb(p, PHB_TXE_ERR_STATUS);
	stat->phbTxeFirstErrorStatus = phb4_read_reg_asb(p, PHB_TXE_ERR1_STATUS);
	stat->phbTxeErrorLog0 = phb4_read_reg_asb(p, PHB_TXE_ERR_LOG_0);
	stat->phbTxeErrorLog1 = phb4_read_reg_asb(p, PHB_TXE_ERR_LOG_1);
	stat->phbRxeArbErrorStatus = phb4_read_reg_asb(p, PHB_RXE_ARB_ERR_STATUS);
	stat->phbRxeArbFirstErrorStatus = phb4_read_reg_asb(p, PHB_RXE_ARB_ERR1_STATUS);
	stat->phbRxeArbErrorLog0 = phb4_read_reg_asb(p, PHB_RXE_ARB_ERR_LOG_0);
	stat->phbRxeArbErrorLog1 = phb4_read_reg_asb(p, PHB_RXE_ARB_ERR_LOG_1);
	stat->phbRxeMrgErrorStatus = phb4_read_reg_asb(p, PHB_RXE_MRG_ERR_STATUS);
	stat->phbRxeMrgFirstErrorStatus = phb4_read_reg_asb(p, PHB_RXE_MRG_ERR1_STATUS);
	stat->phbRxeMrgErrorLog0 = phb4_read_reg_asb(p, PHB_RXE_MRG_ERR_LOG_0);
	stat->phbRxeMrgErrorLog1 = phb4_read_reg_asb(p, PHB_RXE_MRG_ERR_LOG_1);
	stat->phbRxeTceErrorStatus = phb4_read_reg_asb(p, PHB_RXE_TCE_ERR_STATUS);
	stat->phbRxeTceFirstErrorStatus = phb4_read_reg_asb(p, PHB_RXE_TCE_ERR1_STATUS);
	stat->phbRxeTceErrorLog0 = phb4_read_reg_asb(p, PHB_RXE_TCE_ERR_LOG_0);
	stat->phbRxeTceErrorLog1 = phb4_read_reg_asb(p, PHB_RXE_TCE_ERR_LOG_1);

	/* PHB4 REGB error registers */
	stat->phbPblErrorStatus = phb4_read_reg_asb(p, PHB_PBL_ERR_STATUS);
	stat->phbPblFirstErrorStatus = phb4_read_reg_asb(p, PHB_PBL_ERR1_STATUS);
	stat->phbPblErrorLog0 = phb4_read_reg_asb(p, PHB_PBL_ERR_LOG_0);
	stat->phbPblErrorLog1 = phb4_read_reg_asb(p, PHB_PBL_ERR_LOG_1);

	stat->phbPcieDlpErrorStatus = phb4_read_reg_asb(p, PHB_PCIE_DLP_ERR_STATUS);
	stat->phbPcieDlpErrorLog1 = phb4_read_reg_asb(p, PHB_PCIE_DLP_ERRLOG1);
	stat->phbPcieDlpErrorLog2 = phb4_read_reg_asb(p, PHB_PCIE_DLP_ERRLOG2);

	stat->phbRegbErrorStatus = phb4_read_reg_asb(p, PHB_REGB_ERR_STATUS);
	stat->phbRegbFirstErrorStatus = phb4_read_reg_asb(p, PHB_REGB_ERR1_STATUS);
	stat->phbRegbErrorLog0 = phb4_read_reg_asb(p, PHB_REGB_ERR_LOG_0);
	stat->phbRegbErrorLog1 = phb4_read_reg_asb(p, PHB_REGB_ERR_LOG_1);

	/*
	 * Grab PESTA & B content. The error bit (bit#0) should
	 * be fetched from IODA and the left content from memory
	 * resident tables.
	 */
	 pPEST = (uint64_t *)p->tbl_pest;
	 phb4_ioda_sel(p, IODA3_TBL_PESTA, 0, true);
	 for (i = 0; i < OPAL_PHB4_NUM_PEST_REGS; i++) {
		 stat->pestA[i] = phb4_read_reg_asb(p, PHB_IODA_DATA0);
		 stat->pestA[i] |= pPEST[2 * i];
	 }

	 phb4_ioda_sel(p, IODA3_TBL_PESTB, 0, true);
	 for (i = 0; i < OPAL_PHB4_NUM_PEST_REGS; i++) {
		 stat->pestB[i] = phb4_read_reg_asb(p, PHB_IODA_DATA0);
		 stat->pestB[i] |= pPEST[2 * i + 1];
	 }
}

static void phb4_eeh_dump_regs(struct phb4 *p)
{
	struct OpalIoPhb4ErrorData *s;
	uint16_t reg;
	unsigned int i;

	if (!verbose_eeh)
		return;

	s = zalloc(sizeof(struct OpalIoPhb4ErrorData));
	phb4_read_phb_status(p, s);


	PHBERR(p, "brdgCtl        = %08x\n", s->brdgCtl);

	/* PHB4 cfg regs */
	PHBERR(p, "            deviceStatus = %08x\n", s->deviceStatus);
	PHBERR(p, "              slotStatus = %08x\n", s->slotStatus);
	PHBERR(p, "              linkStatus = %08x\n", s->linkStatus);
	PHBERR(p, "            devCmdStatus = %08x\n", s->devCmdStatus);
	PHBERR(p, "            devSecStatus = %08x\n", s->devSecStatus);
	PHBERR(p, "         rootErrorStatus = %08x\n", s->rootErrorStatus);
	PHBERR(p, "         corrErrorStatus = %08x\n", s->corrErrorStatus);
	PHBERR(p, "       uncorrErrorStatus = %08x\n", s->uncorrErrorStatus);

	/* Two non OPAL API registers that are useful */
	phb4_pcicfg_read16(&p->phb, 0, p->ecap + PCICAP_EXP_DEVCTL, &reg);
	PHBERR(p, "                  devctl = %08x\n", reg);
	phb4_pcicfg_read16(&p->phb, 0, p->ecap + PCICAP_EXP_DEVSTAT,
			   &reg);
	PHBERR(p, "                 devStat = %08x\n", reg);

	/* Byte swap TLP headers so they are the same as the PCIe spec */
	PHBERR(p, "                 tlpHdr1 = %08x\n", bswap_32(s->tlpHdr1));
	PHBERR(p, "                 tlpHdr2 = %08x\n", bswap_32(s->tlpHdr2));
	PHBERR(p, "                 tlpHdr3 = %08x\n", bswap_32(s->tlpHdr3));
	PHBERR(p, "                 tlpHdr4 = %08x\n", bswap_32(s->tlpHdr4));
	PHBERR(p, "                sourceId = %08x\n", s->sourceId);
	PHBERR(p, "                    nFir = %016llx\n", s->nFir);
	PHBERR(p, "                nFirMask = %016llx\n", s->nFirMask);
	PHBERR(p, "                 nFirWOF = %016llx\n", s->nFirWOF);
	PHBERR(p, "                phbPlssr = %016llx\n", s->phbPlssr);
	PHBERR(p, "                  phbCsr = %016llx\n", s->phbCsr);
	PHBERR(p, "                  lemFir = %016llx\n", s->lemFir);
	PHBERR(p, "            lemErrorMask = %016llx\n", s->lemErrorMask);
	PHBERR(p, "                  lemWOF = %016llx\n", s->lemWOF);
	PHBERR(p, "          phbErrorStatus = %016llx\n", s->phbErrorStatus);
	PHBERR(p, "     phbFirstErrorStatus = %016llx\n", s->phbFirstErrorStatus);
	PHBERR(p, "            phbErrorLog0 = %016llx\n", s->phbErrorLog0);
	PHBERR(p, "            phbErrorLog1 = %016llx\n", s->phbErrorLog1);
	PHBERR(p, "       phbTxeErrorStatus = %016llx\n", s->phbTxeErrorStatus);
	PHBERR(p, "  phbTxeFirstErrorStatus = %016llx\n", s->phbTxeFirstErrorStatus);
	PHBERR(p, "         phbTxeErrorLog0 = %016llx\n", s->phbTxeErrorLog0);
	PHBERR(p, "         phbTxeErrorLog1 = %016llx\n", s->phbTxeErrorLog1);
	PHBERR(p, "    phbRxeArbErrorStatus = %016llx\n", s->phbRxeArbErrorStatus);
	PHBERR(p, "phbRxeArbFrstErrorStatus = %016llx\n", s->phbRxeArbFirstErrorStatus);
	PHBERR(p, "      phbRxeArbErrorLog0 = %016llx\n", s->phbRxeArbErrorLog0);
	PHBERR(p, "      phbRxeArbErrorLog1 = %016llx\n", s->phbRxeArbErrorLog1);
	PHBERR(p, "    phbRxeMrgErrorStatus = %016llx\n", s->phbRxeMrgErrorStatus);
	PHBERR(p, "phbRxeMrgFrstErrorStatus = %016llx\n", s->phbRxeMrgFirstErrorStatus);
	PHBERR(p, "      phbRxeMrgErrorLog0 = %016llx\n", s->phbRxeMrgErrorLog0);
	PHBERR(p, "      phbRxeMrgErrorLog1 = %016llx\n", s->phbRxeMrgErrorLog1);
	PHBERR(p, "    phbRxeTceErrorStatus = %016llx\n", s->phbRxeTceErrorStatus);
	PHBERR(p, "phbRxeTceFrstErrorStatus = %016llx\n", s->phbRxeTceFirstErrorStatus);
	PHBERR(p, "      phbRxeTceErrorLog0 = %016llx\n", s->phbRxeTceErrorLog0);
	PHBERR(p, "      phbRxeTceErrorLog1 = %016llx\n", s->phbRxeTceErrorLog1);
	PHBERR(p, "       phbPblErrorStatus = %016llx\n", s->phbPblErrorStatus);
	PHBERR(p, "  phbPblFirstErrorStatus = %016llx\n", s->phbPblFirstErrorStatus);
	PHBERR(p, "         phbPblErrorLog0 = %016llx\n", s->phbPblErrorLog0);
	PHBERR(p, "         phbPblErrorLog1 = %016llx\n", s->phbPblErrorLog1);
	PHBERR(p, "     phbPcieDlpErrorLog1 = %016llx\n", s->phbPcieDlpErrorLog1);
	PHBERR(p, "     phbPcieDlpErrorLog2 = %016llx\n", s->phbPcieDlpErrorLog2);
	PHBERR(p, "   phbPcieDlpErrorStatus = %016llx\n", s->phbPcieDlpErrorStatus);

	PHBERR(p, "      phbRegbErrorStatus = %016llx\n", s->phbRegbErrorStatus);
	PHBERR(p, " phbRegbFirstErrorStatus = %016llx\n", s->phbRegbFirstErrorStatus);
	PHBERR(p, "        phbRegbErrorLog0 = %016llx\n", s->phbRegbErrorLog0);
	PHBERR(p, "        phbRegbErrorLog1 = %016llx\n", s->phbRegbErrorLog1);

	for (i = 0; i < OPAL_PHB4_NUM_PEST_REGS; i++) {
		if (!s->pestA[i] && !s->pestB[i])
			continue;
		PHBERR(p, "               PEST[%03d] = %016llx %016llx\n",
		       i, s->pestA[i], s->pestB[i]);
	}
	free(s);
}

static int64_t phb4_set_pe(struct phb *phb,
			   uint64_t pe_number,
			   uint64_t bdfn,
			   uint8_t bcompare,
			   uint8_t dcompare,
			   uint8_t fcompare,
			   uint8_t action)
{
	struct phb4 *p = phb_to_phb4(phb);
	uint64_t mask, val, tmp, idx;
	int32_t all = 0;
	uint16_t *rte;

	/* Sanity check */
	if (!p->tbl_rtt)
		return OPAL_HARDWARE;
	if (action != OPAL_MAP_PE && action != OPAL_UNMAP_PE)
		return OPAL_PARAMETER;
	if (pe_number >= p->num_pes || bdfn > 0xffff ||
	    bcompare > OpalPciBusAll ||
	    dcompare > OPAL_COMPARE_RID_DEVICE_NUMBER ||
	    fcompare > OPAL_COMPARE_RID_FUNCTION_NUMBER)
		return OPAL_PARAMETER;

	/* Figure out the RID range */
	if (bcompare == OpalPciBusAny) {
		mask = 0x0;
		val  = 0x0;
		all  = 0x1;
	} else {
		tmp  = ((0x1 << (bcompare + 1)) - 1) << (15 - bcompare);
		mask = tmp;
		val  = bdfn & tmp;
	}

	if (dcompare == OPAL_IGNORE_RID_DEVICE_NUMBER)
		all = (all << 1) | 0x1;
	else {
		mask |= 0xf8;
		val  |= (bdfn & 0xf8);
	}

	if (fcompare == OPAL_IGNORE_RID_FUNCTION_NUMBER)
		all = (all << 1) | 0x1;
	else {
		mask |= 0x7;
		val  |= (bdfn & 0x7);
	}

	/* Map or unmap the RTT range */
	if (all == 0x7) {
		if (action == OPAL_MAP_PE) {
			for (idx = 0; idx < RTT_TABLE_ENTRIES; idx++)
				p->rte_cache[idx] = pe_number;
		} else {
			for (idx = 0; idx < ARRAY_SIZE(p->rte_cache); idx++)
				p->rte_cache[idx] = PHB4_RESERVED_PE_NUM(p);
		}
		memcpy((void *)p->tbl_rtt, p->rte_cache, RTT_TABLE_SIZE);
	} else {
		rte = (uint16_t *)p->tbl_rtt;
		for (idx = 0; idx < RTT_TABLE_ENTRIES; idx++, rte++) {
			if ((idx & mask) != val)
				continue;
			if (action == OPAL_MAP_PE)
				p->rte_cache[idx] = pe_number;
			else
				p->rte_cache[idx] = PHB4_RESERVED_PE_NUM(p);
			*rte = p->rte_cache[idx];
		}
	}

	/* Invalidate the entire RTC */
	out_be64(p->regs + PHB_RTC_INVALIDATE, PHB_RTC_INVALIDATE_ALL);

	return OPAL_SUCCESS;
}

static int64_t phb4_set_peltv(struct phb *phb,
			      uint32_t parent_pe,
			      uint32_t child_pe,
			      uint8_t state)
{
	struct phb4 *p = phb_to_phb4(phb);
	uint8_t *peltv;
	uint32_t idx, mask;

	/* Sanity check */
	if (!p->tbl_peltv)
		return OPAL_HARDWARE;
	if (parent_pe >= p->num_pes || child_pe >= p->num_pes)
		return OPAL_PARAMETER;

	/* Find index for parent PE */
	idx = parent_pe * (p->max_num_pes / 8);
	idx += (child_pe / 8);
	mask = 0x1 << (7 - (child_pe % 8));

	peltv = (uint8_t *)p->tbl_peltv;
	peltv += idx;
	if (state) {
		*peltv |= mask;
		p->peltv_cache[idx] |= mask;
	} else {
		*peltv &= ~mask;
		p->peltv_cache[idx] &= ~mask;
	}

	return OPAL_SUCCESS;
}

static void phb4_prepare_link_change(struct pci_slot *slot, bool is_up)
{
	struct phb4 *p = phb_to_phb4(slot->phb);
	uint32_t reg32;

	p->has_link = is_up;

	if (is_up) {
		/* Clear AER receiver error status */
		phb4_pcicfg_write32(&p->phb, 0, p->aercap +
				    PCIECAP_AER_CE_STATUS,
				    PCIECAP_AER_CE_RECVR_ERR);
		/* Unmask receiver error status in AER */
		phb4_pcicfg_read32(&p->phb, 0, p->aercap +
				   PCIECAP_AER_CE_MASK, &reg32);
		reg32 &= ~PCIECAP_AER_CE_RECVR_ERR;
		phb4_pcicfg_write32(&p->phb, 0, p->aercap +
				    PCIECAP_AER_CE_MASK, reg32);

		/* Don't block PCI-CFG */
		p->flags &= ~PHB4_CFG_BLOCKED;

		/* Re-enable link down errors */
		out_be64(p->regs + PHB_PCIE_MISC_STRAP,
			 0x0000060000000000ull);

		/* Re-enable error status indicators that trigger irqs */
		out_be64(p->regs + PHB_REGB_ERR_INF_ENABLE,
			 0x2130006efca8bc00ull);
		out_be64(p->regs + PHB_REGB_ERR_ERC_ENABLE,
			 0x0000000000000000ull);
		out_be64(p->regs + PHB_REGB_ERR_FAT_ENABLE,
			 0xde8fff91035743ffull);

		/*
		 * We might lose the bus numbers during the reset operation
		 * and we need to restore them. Otherwise, some adapters (e.g.
		 * IPR) can't be probed properly by the kernel. We don't need
		 * to restore bus numbers for every kind of reset, however,
		 * it's not harmful to always restore the bus numbers, which
		 * simplifies the logic.
		 */
		pci_restore_bridge_buses(slot->phb, slot->pd);
		if (slot->phb->ops->device_init)
			pci_walk_dev(slot->phb, slot->pd,
				     slot->phb->ops->device_init, NULL);
	} else {
		/* Mask AER receiver error */
		phb4_pcicfg_read32(&p->phb, 0, p->aercap +
				   PCIECAP_AER_CE_MASK, &reg32);
		reg32 |= PCIECAP_AER_CE_RECVR_ERR;
		phb4_pcicfg_write32(&p->phb, 0, p->aercap +
				    PCIECAP_AER_CE_MASK, reg32);

		/* Clear error link enable & error link down kill enable */
		out_be64(p->regs + PHB_PCIE_MISC_STRAP, 0);

		/* Disable all error status indicators that trigger irqs */
		out_be64(p->regs + PHB_REGB_ERR_INF_ENABLE, 0);
		out_be64(p->regs + PHB_REGB_ERR_ERC_ENABLE, 0);
		out_be64(p->regs + PHB_REGB_ERR_FAT_ENABLE, 0);

		/* Block PCI-CFG access */
		p->flags |= PHB4_CFG_BLOCKED;
	}
}

static int64_t phb4_get_presence_state(struct pci_slot *slot, uint8_t *val)
{
	struct phb4 *p = phb_to_phb4(slot->phb);
	uint64_t hps, dtctl;

	/* Test for PHB in error state ? */
	if (p->state == PHB4_STATE_BROKEN)
		return OPAL_HARDWARE;

	/* Check hotplug status */
	hps = in_be64(p->regs + PHB_PCIE_HOTPLUG_STATUS);
	if (!(hps & PHB_PCIE_HPSTAT_PRESENCE)) {
		*val = OPAL_PCI_SLOT_PRESENT;
	} else {
		/*
		 * If it says not present but link is up, then we assume
		 * we are on a broken simulation environment and still
		 * return a valid presence. Otherwise, not present.
		 */
		dtctl = in_be64(p->regs + PHB_PCIE_DLP_TRAIN_CTL);
		if (dtctl & PHB_PCIE_DLP_TL_LINKACT) {
			PHBERR(p, "Presence detect 0 but link set !\n");
			*val = OPAL_PCI_SLOT_PRESENT;
		} else {
			*val = OPAL_PCI_SLOT_EMPTY;
		}
	}

	return OPAL_SUCCESS;
}

static int64_t phb4_get_link_info(struct pci_slot *slot, uint8_t *speed,
				   uint8_t *width)
{
	struct phb4 *p = phb_to_phb4(slot->phb);
	uint64_t reg;
	uint16_t state;
	int64_t rc;
	uint8_t s;

	/* Link is up, let's find the actual speed */
	reg = in_be64(p->regs + PHB_PCIE_DLP_TRAIN_CTL);
	if (!(reg & PHB_PCIE_DLP_TL_LINKACT)) {
		*width = 0;
		if (speed)
			*speed = 0;
		return OPAL_SUCCESS;
	}

	rc = phb4_pcicfg_read16(&p->phb, 0,
				p->ecap + PCICAP_EXP_LSTAT, &state);
	if (rc != OPAL_SUCCESS) {
		PHBERR(p, "%s: Error %lld getting link state\n", __func__, rc);
		return OPAL_HARDWARE;
	}

	if (state & PCICAP_EXP_LSTAT_DLLL_ACT) {
		*width = ((state & PCICAP_EXP_LSTAT_WIDTH) >> 4);
		s =  state & PCICAP_EXP_LSTAT_SPEED;
	} else {
		*width = 0;
		s = 0;
	}

	if (speed)
		*speed = s;

	return OPAL_SUCCESS;
}

static int64_t phb4_get_link_state(struct pci_slot *slot, uint8_t *val)
{
	return phb4_get_link_info(slot, NULL, val);
}

static int64_t phb4_retry_state(struct pci_slot *slot)
{
	struct phb4 *p = phb_to_phb4(slot->phb);

	/* Mark link as down */
	phb4_prepare_link_change(slot, false);

	if (!slot->link_retries--) {
		switch (slot->state) {
		case PHB4_SLOT_LINK_WAIT_ELECTRICAL:
			PHBERR(p, "Presence detected but no electrical link\n");
			break;
		case PHB4_SLOT_LINK_WAIT:
			PHBERR(p, "Electrical link detected but won't train\n");
			break;
		case PHB4_SLOT_LINK_STABLE:
			PHBERR(p, "Linked trained but was degraded or unstable\n");
			break;
		default:
			PHBERR(p, "Unknown link issue\n");
		}
		return OPAL_HARDWARE;
	}

	pci_slot_set_state(slot, PHB4_SLOT_CRESET_START);
	return pci_slot_set_sm_timeout(slot, msecs_to_tb(1));
}

static void phb4_train_info(struct phb4 *p, uint64_t reg, unsigned long time)
{
	char s[80];

	snprintf(s, sizeof(s), "TRACE:0x%016llx % 2lims",
		 reg, tb_to_msecs(time));

	if (reg & PHB_PCIE_DLP_TL_LINKACT)
		snprintf(s, sizeof(s), "%s trained ", s);
	else if (reg & PHB_PCIE_DLP_TRAINING)
		snprintf(s, sizeof(s), "%s training", s);
	else if (reg & PHB_PCIE_DLP_INBAND_PRESENCE)
		snprintf(s, sizeof(s), "%s presence", s);
	else
		snprintf(s, sizeof(s), "%s         ", s);

	snprintf(s, sizeof(s), "%s GEN%lli:x%02lli:", s,
		 GETFIELD(PHB_PCIE_DLP_LINK_SPEED, reg),
		 GETFIELD(PHB_PCIE_DLP_LINK_WIDTH, reg));

	switch (GETFIELD(PHB_PCIE_DLP_LTSSM_TRC, reg)) {
	case PHB_PCIE_DLP_LTSSM_RESET:
		snprintf(s, sizeof(s), "%sreset", s);
		break;
	case PHB_PCIE_DLP_LTSSM_DETECT:
		snprintf(s, sizeof(s), "%sdetect", s);
		break;
	case PHB_PCIE_DLP_LTSSM_POLLING:
		snprintf(s, sizeof(s), "%spolling", s);
		break;
	case PHB_PCIE_DLP_LTSSM_CONFIG:
		snprintf(s, sizeof(s), "%sconfig", s);
		break;
	case PHB_PCIE_DLP_LTSSM_L0:
		snprintf(s, sizeof(s), "%sL0", s);
		break;
	case PHB_PCIE_DLP_LTSSM_REC:
		snprintf(s, sizeof(s), "%srecovery", s);
		break;
	case PHB_PCIE_DLP_LTSSM_L1:
		snprintf(s, sizeof(s), "%sL1", s);
		break;
	case PHB_PCIE_DLP_LTSSM_L2:
		snprintf(s, sizeof(s), "%sL2", s);
		break;
	case PHB_PCIE_DLP_LTSSM_HOTRESET:
		snprintf(s, sizeof(s), "%shotreset", s);
		break;
	default:
		snprintf(s, sizeof(s), "%sunvalid", s);
	}
	PHBERR(p, "%s\n", s);
}

/* Check if AIB is fenced via PBCQ NFIR */
static bool phb4_fenced(struct phb4 *p)
{
	uint64_t nfir_p, nfir_n, err_aib;
	uint64_t err_rpt0, err_rpt1;

	/* Already fenced ? */
	if (p->flags & PHB4_AIB_FENCED)
		return true;

	/*
	 * An all 1's from the PHB indicates a PHB freeze/fence. We
	 * don't really differenciate them at this point.
	 */
	if (in_be64(p->regs + PHB_CPU_LOADSTORE_STATUS)!= 0xfffffffffffffffful)
		return false;

	PHBERR(p, "PHB Freeze/Fence detected !\n");

	/* We read the PCI and NEST FIRs and dump them */
	xscom_read(p->chip_id,
		   p->pci_stk_xscom + XPEC_PCI_STK_PCI_FIR, &nfir_p);
	xscom_read(p->chip_id,
		   p->pe_stk_xscom + XPEC_NEST_STK_PCI_NFIR, &nfir_n);
	xscom_read(p->chip_id,
		   p->pe_stk_xscom + XPEC_NEST_STK_ERR_RPT0, &err_rpt0);
	xscom_read(p->chip_id,
		   p->pe_stk_xscom + XPEC_NEST_STK_ERR_RPT1, &err_rpt1);
	xscom_read(p->chip_id,
		   p->pci_stk_xscom + XPEC_PCI_STK_PBAIB_ERR_REPORT, &err_aib);

	PHBERR(p, " PCI FIR=%016llx\n", nfir_p);
	PHBERR(p, "NEST FIR=%016llx\n", nfir_n);
	PHBERR(p, "ERR RPT0=%016llx\n", err_rpt0);
	PHBERR(p, "ERR RPT1=%016llx\n", err_rpt1);
	PHBERR(p, " AIB ERR=%016llx\n", err_aib);

	/* Mark ourselves fenced */
	p->flags |= PHB4_AIB_FENCED;
	p->state = PHB4_STATE_FENCED;

	phb4_eeh_dump_regs(p);

	return true;
}

static bool phb4_check_reg(struct phb4 *p, uint64_t reg)
{
	if (reg == 0xffffffffffffffffUL)
		return !phb4_fenced(p);
	return true;
}

static void phb4_get_info(struct phb *phb, uint16_t bdfn, uint8_t *speed,
			  uint8_t *width)
{
	int32_t ecap;
	uint32_t cap;

	ecap = pci_find_cap(phb, bdfn, PCI_CFG_CAP_ID_EXP);
	pci_cfg_read32(phb, bdfn, ecap + PCICAP_EXP_LCAP, &cap);
	*width = (cap & PCICAP_EXP_LCAP_MAXWDTH) >> 4;
	*speed = cap & PCICAP_EXP_LCAP_MAXSPD;
}

#define PVR_POWER9_CUMULUS		0x00002000

static bool phb4_chip_retry_workaround(void)
{
	unsigned int pvr;

	if (pci_retry_all)
		return true;

	/* Chips that need this retry are:
	 *  - CUMULUS DD1.0
	 *  - NIMBUS DD2.0 and below
	 */
	pvr = mfspr(SPR_PVR);
	if (pvr & PVR_POWER9_CUMULUS) {
		if ((PVR_VERS_MAJ(pvr) == 1) && (PVR_VERS_MIN(pvr) == 0))
			return true;
	} else { /* NIMBUS */
		if (PVR_VERS_MAJ(pvr) == 1)
			return true;
		if ((PVR_VERS_MAJ(pvr) == 2) && (PVR_VERS_MIN(pvr) == 0))
			return true;
	}
	return false;
}

struct pci_card_id {
	uint16_t vendor;
	uint16_t device;
};

static struct pci_card_id retry_whitelist[] = {
	{ 0x1000, 0x005d }, /* LSI Logic MegaRAID SAS-3 3108 */
	{ 0x1000, 0x00c9 }, /* LSI MPT SAS-3 */
	{ 0x104c, 0x8241 }, /* TI xHCI USB */
	{ 0x1077, 0x2261 }, /* QLogic ISP2722-based 16/32Gb FC */
	{ 0x10b5, 0x8725 }, /* PLX Switch: p9dsu, witherspoon */
	{ 0x10b5, 0x8748 }, /* PLX Switch: ZZ */
	{ 0x11f8, 0xf117 }, /* PMC-Sierra/MicroSemi NV1604 */
	{ 0x15b3, 0x1013 }, /* Mellanox ConnectX-4 */
	{ 0x15b3, 0x1017 }, /* Mellanox ConnectX-5 */
	{ 0x15b3, 0x1019 }, /* Mellanox ConnectX-5 Ex */
	{ 0x1a03, 0x1150 }, /* ASPEED AST2500 Switch */
	{ 0x8086, 0x10fb }, /* Intel x520 10G Eth */
	{ 0x9005, 0x028d }, /* MicroSemi PM8069 */
};

#define VENDOR(vdid) ((vdid) & 0xffff)
#define DEVICE(vdid) (((vdid) >> 16) & 0xffff)

static bool phb4_adapter_in_whitelist(uint32_t vdid)
{
	int i;

	if (pci_retry_all)
		return true;

	for (i = 0; i < ARRAY_SIZE(retry_whitelist); i++)
		if ((retry_whitelist[i].vendor == VENDOR(vdid)) &&
		    (retry_whitelist[i].device == DEVICE(vdid)))
			return true;

	return false;
}

#define min(x,y) ((x) < (y) ? x : y)

static bool phb4_link_optimal(struct pci_slot *slot)
{
	struct phb4 *p = phb_to_phb4(slot->phb);
	uint32_t vdid;
	uint16_t bdfn;
	uint8_t trained_speed, phb_speed, dev_speed, target_speed;
	uint8_t trained_width, phb_width, dev_width, target_width;
	bool optimal_speed, optimal_width, optimal, retry_enabled;


	/* Current trained state */
	phb4_get_link_info(slot, &trained_speed, &trained_width);

	/* Get PHB capability */
	/* NOTE: phb_speed will account for the software speed limit */
	phb4_get_info(slot->phb, 0, &phb_speed, &phb_width);

	/* Get device capability */
	bdfn = 0x0100; /* bus=1 dev=0 device=0 */
	/* Since this is the first access, we need to wait for CRS */
	if (!pci_wait_crs(slot->phb, bdfn , &vdid))
		return true;
	phb4_get_info(slot->phb, bdfn, &dev_speed, &dev_width);

	/* Work out if we are optimally trained */
	target_speed = min(phb_speed, dev_speed);
	optimal_speed = (trained_speed >= target_speed);
	target_width = min(phb_width, dev_width);
	optimal_width = (trained_width >= target_width);
	optimal = optimal_width && optimal_speed;
	retry_enabled = phb4_chip_retry_workaround() &&
		phb4_adapter_in_whitelist(vdid);

	PHBDBG(p, "LINK: Card [%04x:%04x] %s Retry:%s\n", VENDOR(vdid),
	       DEVICE(vdid), optimal ? "Optimal" : "Degraded",
	       retry_enabled ? "enabled" : "disabled");
	PHBDBG(p, "LINK: Speed Train:GEN%i PHB:GEN%i DEV:GEN%i%s\n",
	       trained_speed, phb_speed, dev_speed, optimal_speed ? "" : " *");
	PHBDBG(p, "LINK: Width Train:x%02i PHB:x%02i DEV:x%02i%s\n",
	       trained_width, phb_width, dev_width, optimal_width ? "" : " *");

	if (!retry_enabled)
		return true;

	return optimal;
}

/*
 * This is a trace function to watch what's happening duing pcie link
 * training.  If any errors are detected it simply returns so the
 * normal code can deal with it.
 */
static void phb4_training_trace(struct phb4 *p)
{
	uint64_t reg, reglast = -1;
	unsigned long now, start = mftb();

	if (!pci_tracing)
		return;

	while(1) {
		now = mftb();
		reg = in_be64(p->regs + PHB_PCIE_DLP_TRAIN_CTL);
		if (reg != reglast)
			phb4_train_info(p, reg, now - start);
		reglast = reg;

		if (!phb4_check_reg(p, reg)) {
			PHBERR(p, "TRACE: PHB fence waiting link.\n");
			break;
		}
		if (reg & PHB_PCIE_DLP_TL_LINKACT) {
			PHBERR(p, "TRACE: Link trained.\n");
			break;
		}
		if ((now - start) > secs_to_tb(3)) {
			PHBERR(p, "TRACE: Timeout waiting for link up.\n");
			break;
		}
	}
}

static int64_t phb4_poll_link(struct pci_slot *slot)
{
	struct phb4 *p = phb_to_phb4(slot->phb);
	uint64_t reg;

	switch (slot->state) {
	case PHB4_SLOT_NORMAL:
	case PHB4_SLOT_LINK_START:
		PHBDBG(p, "LINK: Start polling\n");
		slot->retries = PHB4_LINK_ELECTRICAL_RETRIES;
		pci_slot_set_state(slot, PHB4_SLOT_LINK_WAIT_ELECTRICAL);
		/* Polling early here has no chance of a false positive */
		return pci_slot_set_sm_timeout(slot, msecs_to_tb(1));
	case PHB4_SLOT_LINK_WAIT_ELECTRICAL:
		/*
		 * Wait for the link electrical connection to be
		 * established (shorter timeout). This allows us to
		 * workaround spurrious presence detect on some machines
		 * without waiting 10s each time
		 *
		 * Note: We *also* check for the full link up bit here
		 * because simics doesn't seem to implement the electrical
		 * link bit at all
		 */
		reg = in_be64(p->regs + PHB_PCIE_DLP_TRAIN_CTL);
		if (!phb4_check_reg(p, reg)) {
			PHBERR(p, "PHB fence waiting for electrical link\n");
			return phb4_retry_state(slot);
		}

		if (reg & (PHB_PCIE_DLP_INBAND_PRESENCE |
			   PHB_PCIE_DLP_TL_LINKACT)) {
			PHBDBG(p, "LINK: Electrical link detected\n");
			pci_slot_set_state(slot, PHB4_SLOT_LINK_WAIT);
			slot->retries = PHB4_LINK_WAIT_RETRIES;
			/* No wait here since already have an elec link */
			return pci_slot_set_sm_timeout(slot, msecs_to_tb(1));
		}

		if (slot->retries-- == 0) {
			PHBERR(p, "LINK: Timeout waiting for electrical link\n");
			PHBDBG(p, "LINK: DLP train control: 0x%016llx\n", reg);
			return OPAL_HARDWARE;
		}
		/* Retry */
		return pci_slot_set_sm_timeout(slot, msecs_to_tb(10));
	case PHB4_SLOT_LINK_WAIT:
		reg = in_be64(p->regs + PHB_PCIE_DLP_TRAIN_CTL);
		if (!phb4_check_reg(p, reg)) {
			PHBERR(p, "LINK: PHB fence waiting for link training\n");
			return phb4_retry_state(slot);
		}
		if (reg & PHB_PCIE_DLP_TL_LINKACT) {
			PHBDBG(p, "LINK: Link is up\n");
			phb4_prepare_link_change(slot, true);
			pci_slot_set_state(slot, PHB4_SLOT_LINK_STABLE);
			return pci_slot_set_sm_timeout(slot, secs_to_tb(1));
		}

		if (slot->retries-- == 0) {
			PHBERR(p, "LINK: Timeout waiting for link up\n");
			PHBDBG(p, "LINK: DLP train control: 0x%016llx\n", reg);
			return phb4_retry_state(slot);
		}
		/* Retry */
		return pci_slot_set_sm_timeout(slot, msecs_to_tb(10));
	case PHB4_SLOT_LINK_STABLE:
		/* Sanity check link */
		if (phb4_fenced(p)) {
			PHBERR(p, "LINK: PHB fenced waiting for stabilty\n");
			return phb4_retry_state(slot);
		}
		reg = in_be64(p->regs + PHB_PCIE_DLP_TRAIN_CTL);
		if (!phb4_check_reg(p, reg)) {
			PHBERR(p, "LINK: PHB fence reading training control\n");
			return phb4_retry_state(slot);
		}
		if (reg & PHB_PCIE_DLP_TL_LINKACT) {
			PHBDBG(p, "LINK: Link is stable\n");
			if (!phb4_link_optimal(slot)) {
				PHBDBG(p, "LINK: Link degraded\n");
				if (slot->link_retries)
					return phb4_retry_state(slot);
				/*
				 * Link is degraded but no more retries, so
				 * settle for what we have :-(
				 */
				PHBERR(p, "LINK: Degraded but no more retries\n");
			}
			pci_slot_set_state(slot, PHB4_SLOT_NORMAL);
			return OPAL_SUCCESS;
		}
		PHBERR(p, "LINK: Went down waiting for stabilty\n");
		PHBDBG(p, "LINK: DLP train control: 0x%016llx\n", reg);
		return phb4_retry_state(slot);
	default:
		PHBERR(p, "LINK: Unexpected slot state %08x\n",
		       slot->state);
	}

	pci_slot_set_state(slot, PHB4_SLOT_NORMAL);
	return OPAL_HARDWARE;
}

static int64_t phb4_hreset(struct pci_slot *slot)
{
	struct phb4 *p = phb_to_phb4(slot->phb);
	uint16_t brctl;
	uint8_t presence = 1;

	switch (slot->state) {
	case PHB4_SLOT_NORMAL:
		PHBDBG(p, "HRESET: Starts\n");
		if (slot->ops.get_presence_state)
			slot->ops.get_presence_state(slot, &presence);
		if (!presence) {
			PHBDBG(p, "HRESET: No device\n");
			return OPAL_SUCCESS;
		}

		PHBDBG(p, "HRESET: Prepare for link down\n");
		phb4_prepare_link_change(slot, false);
		/* fall through */
	case PHB4_SLOT_HRESET_START:
		PHBDBG(p, "HRESET: Assert\n");

		phb4_pcicfg_read16(&p->phb, 0, PCI_CFG_BRCTL, &brctl);
		brctl |= PCI_CFG_BRCTL_SECONDARY_RESET;
		phb4_pcicfg_write16(&p->phb, 0, PCI_CFG_BRCTL, brctl);
		pci_slot_set_state(slot, PHB4_SLOT_HRESET_DELAY);

		return pci_slot_set_sm_timeout(slot, secs_to_tb(1));
	case PHB4_SLOT_HRESET_DELAY:
		PHBDBG(p, "HRESET: Deassert\n");

		/* Clear link errors before we deassert reset */
		phb4_err_clear_regb(p);

		phb4_pcicfg_read16(&p->phb, 0, PCI_CFG_BRCTL, &brctl);
		brctl &= ~PCI_CFG_BRCTL_SECONDARY_RESET;
		phb4_pcicfg_write16(&p->phb, 0, PCI_CFG_BRCTL, brctl);

		/*
		 * Due to some oddball adapters bouncing the link
		 * training a couple of times, we wait for a full second
		 * before we start checking the link status, otherwise
		 * we can get a spurrious link down interrupt which
		 * causes us to EEH immediately.
		 */
		pci_slot_set_state(slot, PHB4_SLOT_HRESET_DELAY2);
		return pci_slot_set_sm_timeout(slot, secs_to_tb(1));
	case PHB4_SLOT_HRESET_DELAY2:
		pci_slot_set_state(slot, PHB4_SLOT_LINK_START);
		return slot->ops.poll_link(slot);
	default:
		PHBERR(p, "Unexpected slot state %08x\n", slot->state);
	}

	pci_slot_set_state(slot, PHB4_SLOT_NORMAL);
	return OPAL_HARDWARE;
}

static int64_t phb4_freset(struct pci_slot *slot)
{
	struct phb4 *p = phb_to_phb4(slot->phb);
	uint8_t presence = 1;
	uint64_t reg;

	switch(slot->state) {
	case PHB4_SLOT_NORMAL:
		PHBDBG(p, "FRESET: Starts\n");

		/* Nothing to do without adapter connected */
		if (slot->ops.get_presence_state)
			slot->ops.get_presence_state(slot, &presence);
		if (!presence) {
			PHBDBG(p, "FRESET: No device\n");
			return OPAL_SUCCESS;
		}

		PHBDBG(p, "FRESET: Prepare for link down\n");

		phb4_prepare_link_change(slot, false);
		/* fall through */
	case PHB4_SLOT_FRESET_START:
		if (!p->skip_perst) {
			PHBDBG(p, "FRESET: Assert\n");
			reg = in_be64(p->regs + PHB_PCIE_CRESET);
			reg &= ~PHB_PCIE_CRESET_PERST_N;
			out_be64(p->regs + PHB_PCIE_CRESET, reg);
			pci_slot_set_state(slot,
				PHB4_SLOT_FRESET_ASSERT_DELAY);
			/* 250ms assert time aligns with powernv */
			return pci_slot_set_sm_timeout(slot, msecs_to_tb(250));
		}

		/* To skip the assert during boot time */
		PHBDBG(p, "FRESET: Assert skipped\n");
		pci_slot_set_state(slot, PHB4_SLOT_FRESET_ASSERT_DELAY);
		p->skip_perst = false;
		/* fall through */
	case PHB4_SLOT_FRESET_ASSERT_DELAY:
		/* Clear link errors before we deassert PERST */
		phb4_err_clear_regb(p);

		if (pci_tracing) {
			/* Enable tracing */
			reg = in_be64(p->regs + PHB_PCIE_DLP_TRWCTL);
			out_be64(p->regs + PHB_PCIE_DLP_TRWCTL,
				 reg | PHB_PCIE_DLP_TRWCTL_EN);
		}

		PHBDBG(p, "FRESET: Deassert\n");
		reg = in_be64(p->regs + PHB_PCIE_CRESET);
		reg |= PHB_PCIE_CRESET_PERST_N;
		out_be64(p->regs + PHB_PCIE_CRESET, reg);
		pci_slot_set_state(slot,
			PHB4_SLOT_FRESET_DEASSERT_DELAY);

		phb4_training_trace(p);

		/* Move on to link poll right away */
		return pci_slot_set_sm_timeout(slot, msecs_to_tb(1));
	case PHB4_SLOT_FRESET_DEASSERT_DELAY:
		pci_slot_set_state(slot, PHB4_SLOT_LINK_START);
		return slot->ops.poll_link(slot);
	default:
		PHBERR(p, "Unexpected slot state %08x\n", slot->state);
	}

	pci_slot_set_state(slot, PHB4_SLOT_NORMAL);
	return OPAL_HARDWARE;
}

static int64_t load_capp_ucode(struct phb4 *p)
{
	int64_t rc;

	if (p->index != CAPP0_PHB_INDEX && p->index != CAPP1_PHB_INDEX)
		return OPAL_HARDWARE;

	/* 0x4341505050534C4C = 'CAPPPSLL' in ASCII */
	rc = capp_load_ucode(p->chip_id, p->phb.opal_id, p->index,
			0x4341505050534C4C, PHB4_CAPP_REG_OFFSET(p),
			CAPP_APC_MASTER_ARRAY_ADDR_REG,
			CAPP_APC_MASTER_ARRAY_WRITE_REG,
			CAPP_SNP_ARRAY_ADDR_REG,
			CAPP_SNP_ARRAY_WRITE_REG);
	return rc;
}

static void do_capp_recovery_scoms(struct phb4 *p)
{
	uint64_t reg;
	uint32_t offset;

	PHBDBG(p, "Doing CAPP recovery scoms\n");

	offset = PHB4_CAPP_REG_OFFSET(p);
	/* disable snoops */
	xscom_write(p->chip_id, SNOOP_CAPI_CONFIG + offset, 0);
	load_capp_ucode(p);
	/* clear err rpt reg*/
	xscom_write(p->chip_id, CAPP_ERR_RPT_CLR + offset, 0);
	/* clear capp fir */
	xscom_write(p->chip_id, CAPP_FIR + offset, 0);

	xscom_read(p->chip_id, CAPP_ERR_STATUS_CTRL + offset, &reg);
	reg &= ~(PPC_BIT(0) | PPC_BIT(1));
	xscom_write(p->chip_id, CAPP_ERR_STATUS_CTRL + offset, reg);
}

static int64_t phb4_creset(struct pci_slot *slot)
{
	struct phb4 *p = phb_to_phb4(slot->phb);
	uint64_t pbcq_status, reg;

	/* Don't even try fixing a broken PHB */
	if (p->state == PHB4_STATE_BROKEN)
		return OPAL_HARDWARE;

	switch (slot->state) {
	case PHB4_SLOT_NORMAL:
	case PHB4_SLOT_CRESET_START:
		PHBDBG(p, "CRESET: Starts\n");

		/* capp recovery */
		if (p->flags & PHB4_CAPP_RECOVERY)
			do_capp_recovery_scoms(p);

		phb4_prepare_link_change(slot, false);
		/* Clear error inject register, preventing recursive errors */
		xscom_write(p->chip_id, p->pe_xscom + 0x2, 0x0);

		/* Force fence on the PHB to work around a non-existent PE */
		if (!phb4_fenced(p))
			xscom_write(p->chip_id, p->pe_stk_xscom + 0x2,
				    0x0000002000000000);

		/*
		 * Force use of ASB for register access until the PHB has
		 * been fully reset.
		 */
		p->flags |= PHB4_CFG_USE_ASB | PHB4_AIB_FENCED;

		/* Assert PREST before clearing errors */
		reg = phb4_read_reg(p, PHB_PCIE_CRESET);
		reg &= ~PHB_PCIE_CRESET_PERST_N;
		phb4_write_reg(p, PHB_PCIE_CRESET, reg);

		/* Clear errors, following the proper sequence */
		phb4_err_clear(p);

		/* Actual reset */
		xscom_write(p->chip_id, p->pci_stk_xscom + XPEC_PCI_STK_ETU_RESET,
			    0x8000000000000000);

		/* Read errors in PFIR and NFIR */
		xscom_read(p->chip_id, p->pci_stk_xscom + 0x0, &p->pfir_cache);
		xscom_read(p->chip_id, p->pe_stk_xscom + 0x0, &p->nfir_cache);

		pci_slot_set_state(slot, PHB4_SLOT_CRESET_WAIT_CQ);
		slot->retries = 500;
		return pci_slot_set_sm_timeout(slot, msecs_to_tb(10));
	case PHB4_SLOT_CRESET_WAIT_CQ:
		// Wait until operations are complete
		xscom_read(p->chip_id, p->pe_stk_xscom + 0xc, &pbcq_status);
		if (!(pbcq_status & 0xC000000000000000)) {
			PHBDBG(p, "CRESET: No pending transactions\n");

			/* Clear errors in PFIR and NFIR */
			xscom_write(p->chip_id, p->pci_stk_xscom + 0x1,
				    ~p->pfir_cache);
			xscom_write(p->chip_id, p->pe_stk_xscom + 0x1,
				    ~p->nfir_cache);

			/* Clear PHB from reset */
			xscom_write(p->chip_id,
				    p->pci_stk_xscom + XPEC_PCI_STK_ETU_RESET, 0x0);

			/* DD1 errata: write to PEST to force update */
			phb4_ioda_sel(p, IODA3_TBL_PESTA, PHB4_RESERVED_PE_NUM(p),
				      false);
			phb4_write_reg(p, PHB_IODA_DATA0, 0);

			pci_slot_set_state(slot, PHB4_SLOT_CRESET_REINIT);
			/* After lifting PHB reset, wait while logic settles */
			return pci_slot_set_sm_timeout(slot, msecs_to_tb(10));
		}

		if (slot->retries-- == 0) {
			PHBERR(p, "Timeout waiting for pending transaction\n");
			goto error;
		}
		return pci_slot_set_sm_timeout(slot, msecs_to_tb(100));
	case PHB4_SLOT_CRESET_REINIT:
		PHBDBG(p, "CRESET: Reinitialization\n");
		p->flags &= ~PHB4_AIB_FENCED;
		p->flags &= ~PHB4_CAPP_RECOVERY;
		p->flags &= ~PHB4_CFG_USE_ASB;
		phb4_init_hw(p, false);
		pci_slot_set_state(slot, PHB4_SLOT_CRESET_FRESET);
		return pci_slot_set_sm_timeout(slot, msecs_to_tb(100));
	case PHB4_SLOT_CRESET_FRESET:
		pci_slot_set_state(slot, PHB4_SLOT_NORMAL);
		return slot->ops.freset(slot);
	default:
		PHBERR(p, "CRESET: Unexpected slot state %08x, resetting...\n",
		       slot->state);
		pci_slot_set_state(slot, PHB4_SLOT_NORMAL);
		return slot->ops.creset(slot);

	}

error:
	/* Mark the PHB as dead and expect it to be removed */
	p->state = PHB4_STATE_BROKEN;
	return OPAL_HARDWARE;
}

/*
 * Initialize root complex slot, which is mainly used to
 * do fundamental reset before PCI enumeration in PCI core.
 * When probing root complex and building its real slot,
 * the operations will be copied over.
 */
static struct pci_slot *phb4_slot_create(struct phb *phb)
{
	struct pci_slot *slot;

	slot = pci_slot_alloc(phb, NULL);
	if (!slot)
		return slot;

	/* Elementary functions */
	slot->ops.get_presence_state  = phb4_get_presence_state;
	slot->ops.get_link_state      = phb4_get_link_state;
	slot->ops.get_power_state     = NULL;
	slot->ops.get_attention_state = NULL;
	slot->ops.get_latch_state     = NULL;
	slot->ops.set_power_state     = NULL;
	slot->ops.set_attention_state = NULL;

	/*
	 * For PHB slots, we have to split the fundamental reset
	 * into 2 steps. We might not have the first step which
	 * is to power off/on the slot, or it's controlled by
	 * individual platforms.
	 */
	slot->ops.prepare_link_change	= phb4_prepare_link_change;
	slot->ops.poll_link		= phb4_poll_link;
	slot->ops.hreset		= phb4_hreset;
	slot->ops.freset		= phb4_freset;
	slot->ops.creset		= phb4_creset;
	slot->link_retries		= PHB4_LINK_LINK_RETRIES;

	return slot;
}

static int64_t phb4_eeh_freeze_status(struct phb *phb, uint64_t pe_number,
				      uint8_t *freeze_state,
				      uint16_t *pci_error_type,
				      uint16_t *severity,
				      uint64_t *phb_status)
{
	struct phb4 *p = phb_to_phb4(phb);
	uint64_t peev_bit = PPC_BIT(pe_number & 0x3f);
	uint64_t peev, pesta, pestb;

	/* Defaults: not frozen */
	*freeze_state = OPAL_EEH_STOPPED_NOT_FROZEN;
	*pci_error_type = OPAL_EEH_NO_ERROR;

	/* Check dead */
	if (p->state == PHB4_STATE_BROKEN) {
		*freeze_state = OPAL_EEH_STOPPED_MMIO_DMA_FREEZE;
		*pci_error_type = OPAL_EEH_PHB_ERROR;
		if (severity)
			*severity = OPAL_EEH_SEV_PHB_DEAD;
		return OPAL_HARDWARE;
	}

	/* Check fence and CAPP recovery */
	if (phb4_fenced(p) || (p->flags & PHB4_CAPP_RECOVERY)) {
		*freeze_state = OPAL_EEH_STOPPED_MMIO_DMA_FREEZE;
		*pci_error_type = OPAL_EEH_PHB_ERROR;
		if (severity)
			*severity = OPAL_EEH_SEV_PHB_FENCED;
		goto bail;
	}

	/* Check the PEEV */
	phb4_ioda_sel(p, IODA3_TBL_PEEV, pe_number / 64, false);
	peev = in_be64(p->regs + PHB_IODA_DATA0);
	if (!(peev & peev_bit))
		return OPAL_SUCCESS;

	/* Indicate that we have an ER pending */
	phb4_set_err_pending(p, true);
	if (severity)
		*severity = OPAL_EEH_SEV_PE_ER;

	/* Read the PESTA & PESTB */
	phb4_ioda_sel(p, IODA3_TBL_PESTA, pe_number, false);
	pesta = in_be64(p->regs + PHB_IODA_DATA0);
	phb4_ioda_sel(p, IODA3_TBL_PESTB, pe_number, false);
	pestb = in_be64(p->regs + PHB_IODA_DATA0);

	/* Convert them */
	if (pesta & IODA3_PESTA_MMIO_FROZEN)
		*freeze_state |= OPAL_EEH_STOPPED_MMIO_FREEZE;
	if (pestb & IODA3_PESTB_DMA_STOPPED)
		*freeze_state |= OPAL_EEH_STOPPED_DMA_FREEZE;

bail:
	if (phb_status)
		PHBERR(p, "%s: deprecated PHB status\n", __func__);

	return OPAL_SUCCESS;
}

static int64_t phb4_eeh_freeze_clear(struct phb *phb, uint64_t pe_number,
				     uint64_t eeh_action_token)
{
	struct phb4 *p = phb_to_phb4(phb);
	uint64_t err, peev;
	int32_t i;
	bool frozen_pe = false;

	if (p->state == PHB4_STATE_BROKEN)
		return OPAL_HARDWARE;

	/* Summary. If nothing, move to clearing the PESTs which can
	 * contain a freeze state from a previous error or simply set
	 * explicitely by the user
	 */
	err = in_be64(p->regs + PHB_ETU_ERR_SUMMARY);
	if (err == 0xffffffffffffffff) {
		if (phb4_fenced(p)) {
			PHBERR(p, "eeh_freeze_clear on fenced PHB\n");
			return OPAL_HARDWARE;
		}
	}
	if (err != 0)
		phb4_err_clear(p);

	/*
	 * We have PEEV in system memory. It would give more performance
	 * to access that directly.
	 */
	if (eeh_action_token & OPAL_EEH_ACTION_CLEAR_FREEZE_MMIO) {
		phb4_ioda_sel(p, IODA3_TBL_PESTA, pe_number, false);
		out_be64(p->regs + PHB_IODA_DATA0, 0);
	}
	if (eeh_action_token & OPAL_EEH_ACTION_CLEAR_FREEZE_DMA) {
		phb4_ioda_sel(p, IODA3_TBL_PESTB, pe_number, false);
		out_be64(p->regs + PHB_IODA_DATA0, 0);
	}


	/* Update ER pending indication */
	phb4_ioda_sel(p, IODA3_TBL_PEEV, 0, true);
	for (i = 0; i < p->num_pes/64; i++) {
		peev = in_be64(p->regs + PHB_IODA_DATA0);
		if (peev) {
			frozen_pe = true;
			break;
		}
	}
	if (frozen_pe) {
		p->err.err_src	 = PHB4_ERR_SRC_PHB;
		p->err.err_class = PHB4_ERR_CLASS_ER;
		p->err.err_bit   = -1;
		phb4_set_err_pending(p, true);
	} else
		phb4_set_err_pending(p, false);

	return OPAL_SUCCESS;
}

static int64_t phb4_eeh_freeze_set(struct phb *phb, uint64_t pe_number,
				   uint64_t eeh_action_token)
{
	struct phb4 *p = phb_to_phb4(phb);
	uint64_t data;

	if (p->state == PHB4_STATE_BROKEN)
		return OPAL_HARDWARE;

	if (pe_number >= p->num_pes)
		return OPAL_PARAMETER;

	if (eeh_action_token != OPAL_EEH_ACTION_SET_FREEZE_MMIO &&
	    eeh_action_token != OPAL_EEH_ACTION_SET_FREEZE_DMA &&
	    eeh_action_token != OPAL_EEH_ACTION_SET_FREEZE_ALL)
		return OPAL_PARAMETER;

	if (eeh_action_token & OPAL_EEH_ACTION_SET_FREEZE_MMIO) {
		phb4_ioda_sel(p, IODA3_TBL_PESTA, pe_number, false);
		data = in_be64(p->regs + PHB_IODA_DATA0);
		data |= IODA3_PESTA_MMIO_FROZEN;
		out_be64(p->regs + PHB_IODA_DATA0, data);
	}

	if (eeh_action_token & OPAL_EEH_ACTION_SET_FREEZE_DMA) {
		phb4_ioda_sel(p, IODA3_TBL_PESTB, pe_number, false);
		data = in_be64(p->regs + PHB_IODA_DATA0);
		data |= IODA3_PESTB_DMA_STOPPED;
		out_be64(p->regs + PHB_IODA_DATA0, data);
	}

	return OPAL_SUCCESS;
}

static int64_t phb4_eeh_next_error(struct phb *phb,
				   uint64_t *first_frozen_pe,
				   uint16_t *pci_error_type,
				   uint16_t *severity)
{
	struct phb4 *p = phb_to_phb4(phb);
	uint64_t peev;
	uint32_t peev_size = p->num_pes/64;
	int32_t i, j;

	/* If the PHB is broken, we needn't go forward */
	if (p->state == PHB4_STATE_BROKEN) {
		*pci_error_type = OPAL_EEH_PHB_ERROR;
		*severity = OPAL_EEH_SEV_PHB_DEAD;
		return OPAL_SUCCESS;
	}

	if ((p->flags & PHB4_CAPP_RECOVERY)) {
		*pci_error_type = OPAL_EEH_PHB_ERROR;
		*severity = OPAL_EEH_SEV_PHB_FENCED;
		return OPAL_SUCCESS;
	}

	/*
	 * Check if we already have pending errors. If that's
	 * the case, then to get more information about the
	 * pending errors. Here we try PBCQ prior to PHB.
	 */
	if (phb4_err_pending(p) /*&&
	    !phb4_err_check_pbcq(p) &&
	    !phb4_err_check_lem(p) */)
		phb4_set_err_pending(p, false);

	/* Clear result */
	*pci_error_type  = OPAL_EEH_NO_ERROR;
	*severity	 = OPAL_EEH_SEV_NO_ERROR;
	*first_frozen_pe = (uint64_t)-1;

	/* Check frozen PEs */
	if (!phb4_err_pending(p)) {
		phb4_ioda_sel(p, IODA3_TBL_PEEV, 0, true);
		for (i = 0; i < peev_size; i++) {
			peev = in_be64(p->regs + PHB_IODA_DATA0);
			if (peev) {
				p->err.err_src	 = PHB4_ERR_SRC_PHB;
				p->err.err_class = PHB4_ERR_CLASS_ER;
				p->err.err_bit	 = -1;
				phb4_set_err_pending(p, true);
				break;
			}
		}
	}

	if (!phb4_err_pending(p))
		return OPAL_SUCCESS;
	/*
	 * If the frozen PE is caused by a malfunctioning TLP, we
	 * need reset the PHB. So convert ER to PHB-fatal error
	 * for the case.
	 */
	if (p->err.err_class == PHB4_ERR_CLASS_ER) {
		for (i = peev_size - 1; i >= 0; i--) {
			phb4_ioda_sel(p, IODA3_TBL_PEEV, i, false);
			peev = in_be64(p->regs + PHB_IODA_DATA0);
			for (j = 0; j < 64; j++) {
				if (peev & PPC_BIT(j)) {
					*first_frozen_pe = i * 64 + j;
					break;
				}
			}
			if (*first_frozen_pe != (uint64_t)(-1))
				break;
		}

	}

	switch (p->err.err_class) {
	case PHB4_ERR_CLASS_DEAD:
		*pci_error_type = OPAL_EEH_PHB_ERROR;
		*severity = OPAL_EEH_SEV_PHB_DEAD;
		break;
	case PHB4_ERR_CLASS_FENCED:
		*pci_error_type = OPAL_EEH_PHB_ERROR;
		*severity = OPAL_EEH_SEV_PHB_FENCED;
		break;
	case PHB4_ERR_CLASS_ER:
		*pci_error_type = OPAL_EEH_PE_ERROR;
		*severity = OPAL_EEH_SEV_PE_ER;

		/* No frozen PE ? */
		if (*first_frozen_pe == (uint64_t)-1) {
			*pci_error_type = OPAL_EEH_NO_ERROR;
			*severity = OPAL_EEH_SEV_NO_ERROR;
			phb4_set_err_pending(p, false);
		}

		break;
	case PHB4_ERR_CLASS_INF:
		*pci_error_type = OPAL_EEH_PHB_ERROR;
		*severity = OPAL_EEH_SEV_INF;
		break;
	default:
		*pci_error_type = OPAL_EEH_NO_ERROR;
		*severity = OPAL_EEH_SEV_NO_ERROR;
		phb4_set_err_pending(p, false);
	}
	return OPAL_SUCCESS;
}

static int64_t phb4_err_inject_finalize(struct phb4 *phb, uint64_t addr,
					uint64_t mask, uint64_t ctrl,
					bool is_write)
{
	if (is_write)
		ctrl |= PHB_PAPR_ERR_INJ_CTL_WR;
	else
		ctrl |= PHB_PAPR_ERR_INJ_CTL_RD;

	out_be64(phb->regs + PHB_PAPR_ERR_INJ_ADDR, addr);
	out_be64(phb->regs + PHB_PAPR_ERR_INJ_MASK, mask);
	out_be64(phb->regs + PHB_PAPR_ERR_INJ_CTL, ctrl);

	return OPAL_SUCCESS;
}

static int64_t phb4_err_inject_mem32(struct phb4 *phb, uint64_t pe_number,
				     uint64_t addr, uint64_t mask,
				     bool is_write)
{
	return OPAL_UNSUPPORTED;
}

static int64_t phb4_err_inject_mem64(struct phb4 *phb, uint64_t pe_number,
				     uint64_t addr, uint64_t mask,
				     bool is_write)
{
	return OPAL_UNSUPPORTED;
}

static int64_t phb4_err_inject_cfg(struct phb4 *phb, uint64_t pe_number,
				   uint64_t addr, uint64_t mask,
				   bool is_write)
{
	uint64_t a, m, prefer, ctrl;
	int bdfn;
	bool is_bus_pe = false;

	a = 0xffffull;
	prefer = 0xffffull;
	m = PHB_PAPR_ERR_INJ_MASK_CFG_ALL;
	ctrl = PHB_PAPR_ERR_INJ_CTL_CFG;

	for (bdfn = 0; bdfn < RTT_TABLE_ENTRIES; bdfn++) {
		if (phb->rte_cache[bdfn] != pe_number)
			continue;

		/* The PE can be associated with PCI bus or device */
		is_bus_pe = false;
		if ((bdfn + 8) < RTT_TABLE_ENTRIES &&
		    phb->rte_cache[bdfn + 8] == pe_number)
			is_bus_pe = true;

		/* Figure out the PCI config address */
		if (prefer == 0xffffull) {
			if (is_bus_pe) {
				m = PHB_PAPR_ERR_INJ_MASK_CFG;
				prefer = SETFIELD(m, 0x0ull, (bdfn >> 8));
			} else {
				m = PHB_PAPR_ERR_INJ_MASK_CFG_ALL;
				prefer = SETFIELD(m, 0x0ull, bdfn);
			}
		}

		/* Check the input address is valid or not */
		if (!is_bus_pe &&
		    GETFIELD(PHB_PAPR_ERR_INJ_MASK_CFG_ALL, addr) == bdfn) {
			a = addr;
			break;
		}

		if (is_bus_pe &&
		    GETFIELD(PHB_PAPR_ERR_INJ_MASK_CFG, addr) == (bdfn >> 8)) {
			a = addr;
			break;
		}
	}

	/* Invalid PE number */
	if (prefer == 0xffffull)
		return OPAL_PARAMETER;

	/* Specified address is out of range */
	if (a == 0xffffull)
		a = prefer;
	else
		m = mask;

	return phb4_err_inject_finalize(phb, a, m, ctrl, is_write);
}

static int64_t phb4_err_inject_dma(struct phb4 *phb, uint64_t pe_number,
				   uint64_t addr, uint64_t mask,
				   bool is_write, bool is_64bits)
{
	return OPAL_UNSUPPORTED;
}

static int64_t phb4_err_inject_dma32(struct phb4 *phb, uint64_t pe_number,
				     uint64_t addr, uint64_t mask,
				     bool is_write)
{
	return phb4_err_inject_dma(phb, pe_number, addr, mask, is_write, false);
}

static int64_t phb4_err_inject_dma64(struct phb4 *phb, uint64_t pe_number,
				     uint64_t addr, uint64_t mask,
				     bool is_write)
{
	return phb4_err_inject_dma(phb, pe_number, addr, mask, is_write, true);
}


static int64_t phb4_err_inject(struct phb *phb, uint64_t pe_number,
			       uint32_t type, uint32_t func,
			       uint64_t addr, uint64_t mask)
{
	struct phb4 *p = phb_to_phb4(phb);
	int64_t (*handler)(struct phb4 *p, uint64_t pe_number,
			   uint64_t addr, uint64_t mask, bool is_write);
	bool is_write;

	/* How could we get here without valid RTT? */
	if (!p->tbl_rtt)
		return OPAL_HARDWARE;

	/* We can't inject error to the reserved PE */
	if (pe_number == PHB4_RESERVED_PE_NUM(p) || pe_number >= p->num_pes)
		return OPAL_PARAMETER;

	/* Clear leftover from last time */
	out_be64(p->regs + PHB_PAPR_ERR_INJ_CTL, 0x0ul);

	switch (func) {
	case OPAL_ERR_INJECT_FUNC_IOA_LD_MEM_ADDR:
	case OPAL_ERR_INJECT_FUNC_IOA_LD_MEM_DATA:
		is_write = false;
		if (type == OPAL_ERR_INJECT_TYPE_IOA_BUS_ERR64)
			handler = phb4_err_inject_mem64;
		else
			handler = phb4_err_inject_mem32;
		break;
	case OPAL_ERR_INJECT_FUNC_IOA_ST_MEM_ADDR:
	case OPAL_ERR_INJECT_FUNC_IOA_ST_MEM_DATA:
		is_write = true;
		if (type == OPAL_ERR_INJECT_TYPE_IOA_BUS_ERR64)
			handler = phb4_err_inject_mem64;
		else
			handler = phb4_err_inject_mem32;
		break;
	case OPAL_ERR_INJECT_FUNC_IOA_LD_CFG_ADDR:
	case OPAL_ERR_INJECT_FUNC_IOA_LD_CFG_DATA:
		is_write = false;
		handler = phb4_err_inject_cfg;
		break;
	case OPAL_ERR_INJECT_FUNC_IOA_ST_CFG_ADDR:
	case OPAL_ERR_INJECT_FUNC_IOA_ST_CFG_DATA:
		is_write = true;
		handler = phb4_err_inject_cfg;
		break;
	case OPAL_ERR_INJECT_FUNC_IOA_DMA_RD_ADDR:
	case OPAL_ERR_INJECT_FUNC_IOA_DMA_RD_DATA:
	case OPAL_ERR_INJECT_FUNC_IOA_DMA_RD_MASTER:
	case OPAL_ERR_INJECT_FUNC_IOA_DMA_RD_TARGET:
		is_write = false;
		if (type == OPAL_ERR_INJECT_TYPE_IOA_BUS_ERR64)
			handler = phb4_err_inject_dma64;
		else
			handler = phb4_err_inject_dma32;
		break;
	case OPAL_ERR_INJECT_FUNC_IOA_DMA_WR_ADDR:
	case OPAL_ERR_INJECT_FUNC_IOA_DMA_WR_DATA:
	case OPAL_ERR_INJECT_FUNC_IOA_DMA_WR_MASTER:
	case OPAL_ERR_INJECT_FUNC_IOA_DMA_WR_TARGET:
		is_write = true;
		if (type == OPAL_ERR_INJECT_TYPE_IOA_BUS_ERR64)
			handler = phb4_err_inject_dma64;
		else
			handler = phb4_err_inject_dma32;
		break;
	default:
		return OPAL_PARAMETER;
	}

	return handler(p, pe_number, addr, mask, is_write);
}

static int64_t phb4_get_diag_data(struct phb *phb,
				  void *diag_buffer,
				  uint64_t diag_buffer_len)
{
	struct phb4 *p = phb_to_phb4(phb);
	struct OpalIoPhb4ErrorData *data = diag_buffer;

	if (diag_buffer_len < sizeof(struct OpalIoPhb4ErrorData))
		return OPAL_PARAMETER;
	if (p->state == PHB4_STATE_BROKEN)
		return OPAL_HARDWARE;

	/*
	 * Dummy check for fence so that phb4_read_phb_status knows
	 * whether to use ASB or AIB
	 */
	phb4_fenced(p);
	phb4_read_phb_status(p, data);

	if (!(p->flags & PHB4_AIB_FENCED))
		phb4_eeh_dump_regs(p);

	/*
	 * We're running to here probably because of errors
	 * (INF class). For that case, we need clear the error
	 * explicitly.
	 */
	if (phb4_err_pending(p) &&
	    p->err.err_class == PHB4_ERR_CLASS_INF &&
	    p->err.err_src == PHB4_ERR_SRC_PHB) {
		phb4_err_clear(p);
		phb4_set_err_pending(p, false);
	}

	return OPAL_SUCCESS;
}

static uint64_t tve_encode_50b_noxlate(uint64_t start_addr, uint64_t end_addr)
{
	uint64_t tve;

	/*
	 * Put start address bits 49:24 into TVE[52:53]||[0:23]
	 * and end address bits 49:24 into TVE[54:55]||[24:47]
	 * and set TVE[51]
	 */
	tve  = (start_addr << 16) & (0xffffffull << 40);
	tve |= (start_addr >> 38) & (3ull << 10);
	tve |= (end_addr >>  8) & (0xfffffful << 16);
	tve |= (end_addr >> 40) & (3ull << 8);
	tve |= PPC_BIT(51) | IODA3_TVT_NON_TRANSLATE_50;
	return tve;
}

static int64_t phb4_get_capp_info(int chip_id, struct phb *phb,
				  struct capp_info *info)
{
	struct phb4 *p = phb_to_phb4(phb);
	struct proc_chip *chip = get_chip(p->chip_id);
	uint32_t offset;

	if (chip_id != p->chip_id)
		return OPAL_PARAMETER;

	if (!((1 << p->index) & chip->capp_phb4_attached_mask))
		return OPAL_PARAMETER;

	offset = PHB4_CAPP_REG_OFFSET(p);

	if (p->index == CAPP0_PHB_INDEX)
		info->capp_index = 0;
	if (p->index == CAPP1_PHB_INDEX)
		info->capp_index = 1;
	info->phb_index = p->index;
	info->capp_fir_reg = CAPP_FIR + offset;
	info->capp_fir_mask_reg = CAPP_FIR_MASK + offset;
	info->capp_fir_action0_reg = CAPP_FIR_ACTION0 + offset;
	info->capp_fir_action1_reg = CAPP_FIR_ACTION1 + offset;
	info->capp_err_status_ctrl_reg = CAPP_ERR_STATUS_CTRL + offset;

	return OPAL_SUCCESS;
}

static void phb4_init_capp_regs(struct phb4 *p)
{
	uint64_t reg;
	uint32_t offset;

	offset = PHB4_CAPP_REG_OFFSET(p);

	/* APC Master PowerBus Control Register */
	xscom_read(p->chip_id, APC_MASTER_PB_CTRL + offset, &reg);
	reg |= PPC_BIT(0); /* enable cResp exam */
	reg |= PPC_BIT(3); /* disable vg not sys */
	if (p->rev == PHB4_REV_NIMBUS_DD10) {
		reg |= PPC_BIT(1);
	}
	if (p->rev == PHB4_REV_NIMBUS_DD20) {
		reg |= PPC_BIT(2); /* disable nn rn */
		reg |= PPC_BIT(4); /* disable g */
		reg |= PPC_BIT(5); /* disable ln */
	}
	xscom_write(p->chip_id, APC_MASTER_PB_CTRL + offset, reg);

	/* Set PHB mode, HPC Dir State and P9 mode */
	xscom_write(p->chip_id, APC_MASTER_CAPI_CTRL + offset,
		    0x1772000000000000);
	PHBINF(p, "CAPP: port attached\n");

	/* Set snoop ttype decoding , dir size to 256k */
	xscom_write(p->chip_id, SNOOP_CAPI_CONFIG + offset, 0xA000000000000000);

	/* Use Read Epsilon Tier2 for all scopes.
	 * Set Tier2 Read Epsilon.
	 */
	xscom_read(p->chip_id, SNOOP_CONTROL + offset, &reg);
	reg |= PPC_BIT(0);
	reg |= PPC_BIT(35);
	reg |= PPC_BIT(45);
	reg |= PPC_BIT(46);
	reg |= PPC_BIT(47);
	reg |= PPC_BIT(50);
	xscom_write(p->chip_id, SNOOP_CONTROL + offset, reg);

	/* Transport Control Register */
	xscom_read(p->chip_id, TRANSPORT_CONTROL + offset, &reg);
	if (p->index == CAPP0_PHB_INDEX) {
		reg |= PPC_BIT(1); /* Send Packet Timer Value */
		reg |= PPC_BITMASK(10, 13); /* Send Packet Timer Value */
		reg &= ~PPC_BITMASK(18, 21); /* Set Max tlbi divider */
		reg |= PPC_BIT(62);
	}
	if (p->index == CAPP1_PHB_INDEX) {
		reg |= PPC_BIT(4); /* Send Packet Timer Value */
		reg |= PPC_BIT(11); /* Set CI Store Buffer Threshold=5 */
		reg |= PPC_BIT(13); /* Set CI Store Buffer Threshold=5 */
	}
	reg &= ~PPC_BITMASK(14, 17); /* Set Max LPC CI store buffer to zeros */
	reg |= PPC_BIT(60); /* Set lowest CI Store buffer used bits */
	xscom_write(p->chip_id, TRANSPORT_CONTROL + offset, reg);

	/* Initialize CI Store Buffers */
	xscom_read(p->chip_id, TRANSPORT_CONTROL + offset, &reg);
	reg |= PPC_BIT(63);
	xscom_write(p->chip_id, TRANSPORT_CONTROL + offset, reg);

	/* Enable epoch timer */
	xscom_write(p->chip_id, EPOCH_RECOVERY_TIMERS_CTRL + offset,
		    0xC0000000FFF8FFE0);

	/* Flush SUE State Map Register */
	xscom_write(p->chip_id, FLUSH_SUE_STATE_MAP + offset,
		    0x08020A0000000000);

	if (p->rev == PHB4_REV_NIMBUS_DD20) {
		/* Flush SUE uOP1 Register */
		xscom_write(p->chip_id, FLUSH_SUE_UOP1 + offset,
			    0xDCE0280428000000);
	}

	/* capp owns PHB read buffers */
	if (p->index == CAPP0_PHB_INDEX) {
		xscom_write(p->chip_id, APC_FSM_READ_MASK + offset,
			    0xFFFFFFFFFFFF0000);
		xscom_write(p->chip_id, XPT_FSM_RMM + offset,
			    0xFFFFFFFFFFFF0000);
	}
	if (p->index == CAPP1_PHB_INDEX) {
		/* Set 30 Read machines for CAPP Minus 20-27 for DMA */
		xscom_write(p->chip_id, APC_FSM_READ_MASK + offset,
			    0xFFFFF00E00000000);
		xscom_write(p->chip_id, XPT_FSM_RMM + offset,
			    0xFFFFF00E00000000);
	}

	/* CAPP FIR Action 0 */
	xscom_write(p->chip_id, CAPP_FIR_ACTION0 + offset, 0x0b1c000104060000);

	/* CAPP FIR Action 1 */
	xscom_write(p->chip_id, CAPP_FIR_ACTION1 + offset, 0x2b9c0001240E0000);

	/* CAPP FIR MASK */
	xscom_write(p->chip_id, CAPP_FIR_MASK + offset, 0x80031f98d8717000);

	/* Mask the CAPP PSL Credit Timeout Register error */
	xscom_write_mask(p->chip_id, CAPP_FIR_MASK + offset,
			 PPC_BIT(46), PPC_BIT(46));

	/* Deassert TLBI_FENCED and tlbi_psl_is_dead */
	xscom_write(p->chip_id, CAPP_ERR_STATUS_CTRL + offset, 0);
}

/* override some inits with CAPI defaults */
static void phb4_init_capp_errors(struct phb4 *p)
{
	/* Init_77: TXE Error AIB Fence Enable Register */
	out_be64(p->regs + 0x0d30,	0xdff7bf0bf7ddfff0ull);

	/* Init_86: RXE_ARB Error AIB Fence Enable Register */
	out_be64(p->regs + 0x0db0,	0xfbffd7bbfb7fbfefull);

	/* Init_95: RXE_MRG Error AIB Fence Enable Register */
	out_be64(p->regs + 0x0e30,	0xfffffeffff7fff57ull);

	/* Init_104: RXE_TCE Error AIB Fence Enable Register */
	out_be64(p->regs + 0x0eb0,	0xffaeffafffffffffull);

	/* Init_113: PHB Error AIB Fence Enable Register */
	out_be64(p->regs + 0x0cb0,	0x35777073ff000000ull);
}

/* Power Bus Common Queue Registers
 * All PBCQ and PBAIB registers are accessed via SCOM
 * NestBase = 4010C00 for PEC0
 *            4011000 for PEC1
 *            4011400 for PEC2
 * PCIBase  = D010800 for PE0
 *            E010800 for PE1
 *            F010800 for PE2
 *
 * Some registers are shared amongst all of the stacks and will only
 * have 1 copy. Other registers are implemented one per stack.
 * Registers that are duplicated will have an additional offset
 * of “StackBase” so that they have a unique address.
 * Stackoffset = 00000040 for Stack0
 *             = 00000080 for Stack1
 *             = 000000C0 for Stack2
 */
static int64_t enable_capi_mode(struct phb4 *p, uint64_t pe_number,
				enum capi_dma_tvt dma_tvt)
{
	uint64_t reg, start_addr, end_addr;
	int i;

	/* CAPP Control Register */
	xscom_read(p->chip_id, p->pe_xscom + XPEC_NEST_CAPP_CNTL, &reg);
	if (reg & PPC_BIT(0)) {
		PHBDBG(p, "Already in CAPP mode\n");
	}

	for (i = 0; i < 500000; i++) {
		/* PBCQ General Status Register */
		xscom_read(p->chip_id,
			   p->pe_stk_xscom + XPEC_NEST_STK_PBCQ_STAT,
			   &reg);
		if (!(reg & 0xC000000000000000))
			break;
		time_wait_us(10);
	}
	if (reg & 0xC000000000000000) {
		PHBERR(p, "CAPP: Timeout waiting for pending transaction\n");
		return OPAL_HARDWARE;
	}

	/* CAPP Control Register. Enable CAPP Mode */
	if (p->index == CAPP0_PHB_INDEX) {
		/* PBCQ is operating as a x16 stack the maximum number
		 * of engines give to CAPP will be 14 and will be
		 * assigned in the order of STQ 15 to 2
		 */
		/* PBCQ is operating as a x16 stack engines 0-47 are
		 * available for capp use.
		 * Set 48 Read machines for CAPP
		 */
		reg = 0x800EFFFFFFFFFFFFULL;
	}
	if (p->index == CAPP1_PHB_INDEX) {
		/* PBCQ is operating as a x8 stack the maximum number of
		 * engines given to CAPP should be 6 and will be
		 * assigned in the order of 7 to 2.
		 */
		/* PBCQ is operating as a x8 stack the only engines
		 * 0-30 are available for capp use.
		 * Set 30 Read machines, minus 20-27 for DMA
		 */
		reg = 0x8006FFFFF00E0000ULL;
	}
	xscom_write(p->chip_id, p->pe_xscom + XPEC_NEST_CAPP_CNTL, reg);

	/* PCI to PB data movement ignores the PB init signal.
	 * Disable streaming.
	 */
	xscom_read(p->chip_id, p->pe_xscom + XPEC_NEST_PBCQ_HW_CONFIG, &reg);
	reg |= XPEC_NEST_PBCQ_HW_CONFIG_PBINIT;
	if (p->index == CAPP0_PHB_INDEX)
		reg &= ~XPEC_NEST_PBCQ_HW_CONFIG_CH_STR;
	xscom_write(p->chip_id, p->pe_xscom + XPEC_NEST_PBCQ_HW_CONFIG, reg);

	/* PEC Phase 4 (PHB) registers adjustment
	 * Inbound CAPP traffic: The CAPI can send both CAPP packets and
	 * I/O packets. A PCIe packet is indentified as a CAPP packet in
	 * the PHB if the PCIe address matches either the CAPI
	 * Compare/Mask register or its NBW Compare/Mask register.
	 */

	/*
	 * Bit [0:7] XSL_DSNCTL[capiind]
	 * Init_25 - CAPI Compare/Mask
	 */
	out_be64(p->regs + PHB_CAPI_CMPM,
		 0x0200FE0000000000Ull | PHB_CAPI_CMPM_ENABLE);

	if (!(p->rev == PHB4_REV_NIMBUS_DD10)) {
		/* Init_24 - ASN Compare/Mask */
		out_be64(p->regs + PHB_PBL_ASN_CMPM,
			 0x0400FF0000000000Ull | PHB_PBL_ASN_ENABLE);

		/* PBCQ Tunnel Bar Register
		 * Write Tunnel register to match PSL TNR register
		 */
		xscom_write(p->chip_id,
			    p->pe_stk_xscom + XPEC_NEST_STK_TUNNEL_BAR,
			    0x020000E000000000);

		/* PB AIB Hardware Control Register
		 * Wait 32 PCI clocks for a credit to become available
		 * before rejecting.
		 */
		xscom_read(p->chip_id,
			   p->pci_xscom + XPEC_PCI_PBAIB_HW_CONFIG, &reg);
		reg |= PPC_BITMASK(40, 42);
		if (p->index == CAPP1_PHB_INDEX)
			reg |= PPC_BIT(30);
		xscom_write(p->chip_id,
			    p->pci_xscom + XPEC_PCI_PBAIB_HW_CONFIG,
			    reg);
	}

	/* non-translate/50-bit mode */
	out_be64(p->regs + PHB_NXLATE_PREFIX, 0x0000000000000000Ull);

	/* set tve no translate mode allow mmio window */
	memset(p->tve_cache, 0x0, sizeof(p->tve_cache));

	/*
	 * In 50-bit non-translate mode, the fields of the TVE are
	 * used to perform an address range check. In this mode TCE
	 * Table Size(0) must be a '1' (TVE[51] = 1)
	 *      PCI Addr(49:24) >= TVE[52:53]+TVE[0:23] and
	 *      PCI Addr(49:24) < TVE[54:55]+TVE[24:47]
	 *
	 * TVE[51] = 1
	 * TVE[56] = 1: 50-bit Non-Translate Mode Enable
	 * TVE[0:23] = 0x000000
	 * TVE[24:47] = 0xFFFFFF
	 *
	 * capi dma mode: CAPP DMA mode needs access to all of memory
	 * capi mode: Allow address range (bit 14 = 1)
	 *            0x0002000000000000: 0x0002FFFFFFFFFFFF
	 *            TVE[52:53] = '10' and TVE[54:55] = '10'
	 */

	/* TVT#0: CAPI window + DMA, all memory */
	start_addr = 0ull;
	end_addr   = 0x0003ffffffffffffull;
	p->tve_cache[pe_number * 2] =
		tve_encode_50b_noxlate(start_addr, end_addr);

	/* TVT#1: DMA, all memory, in bypass mode */
	if (dma_tvt == CAPI_DMA_TVT1) {
		start_addr = (1ull << 59);
		end_addr   = start_addr + 0x0003ffffffffffffull;
		p->tve_cache[pe_number * 2 + 1] =
			tve_encode_50b_noxlate(start_addr, end_addr);
	}

	phb4_ioda_sel(p, IODA3_TBL_TVT, 0, true);
	for (i = 0; i < p->tvt_size; i++)
		out_be64(p->regs + PHB_IODA_DATA0, p->tve_cache[i]);

	/* set mbt bar to pass capi mmio window. First applied cleared
	 * values to HW
	 */
	for (i = 0; i < p->mbt_size; i++) {
		p->mbt_cache[i][0] = 0;
		p->mbt_cache[i][1] = 0;
	}
	phb4_ioda_sel(p, IODA3_TBL_MBT, 0, true);
	for (i = 0; i < p->mbt_size; i++) {
		out_be64(p->regs + PHB_IODA_DATA0, p->mbt_cache[i][0]);
		out_be64(p->regs + PHB_IODA_DATA0, p->mbt_cache[i][1]);
	}

	p->mbt_cache[0][0] = IODA3_MBT0_ENABLE |
			     IODA3_MBT0_TYPE_M64 |
		SETFIELD(IODA3_MBT0_MODE, 0ull, IODA3_MBT0_MODE_SINGLE_PE) |
		SETFIELD(IODA3_MBT0_MDT_COLUMN, 0ull, 0) |
		(p->mm0_base & IODA3_MBT0_BASE_ADDR);
	p->mbt_cache[0][1] = IODA3_MBT1_ENABLE |
		((~(p->mm0_size - 1)) & IODA3_MBT1_MASK) |
		SETFIELD(IODA3_MBT1_SINGLE_PE_NUM, 0ull, pe_number);

	p->mbt_cache[1][0] = IODA3_MBT0_ENABLE |
			     IODA3_MBT0_TYPE_M64 |
		SETFIELD(IODA3_MBT0_MODE, 0ull, IODA3_MBT0_MODE_SINGLE_PE) |
		SETFIELD(IODA3_MBT0_MDT_COLUMN, 0ull, 0) |
		(0x0002000000000000ULL & IODA3_MBT0_BASE_ADDR);
	p->mbt_cache[1][1] = IODA3_MBT1_ENABLE |
		(0x00ff000000000000ULL & IODA3_MBT1_MASK) |
		SETFIELD(IODA3_MBT1_SINGLE_PE_NUM, 0ull, pe_number);

	phb4_ioda_sel(p, IODA3_TBL_MBT, 0, true);
	for (i = 0; i < p->mbt_size; i++) {
		out_be64(p->regs + PHB_IODA_DATA0, p->mbt_cache[i][0]);
		out_be64(p->regs + PHB_IODA_DATA0, p->mbt_cache[i][1]);
	}

	phb4_init_capp_errors(p);

	phb4_init_capp_regs(p);

	if (!chiptod_capp_timebase_sync(p->chip_id, CAPP_TFMR,
					CAPP_TB,
					PHB4_CAPP_REG_OFFSET(p))) {
		PHBERR(p, "CAPP: Failed to sync timebase\n");
		return OPAL_HARDWARE;
	}

	/* set callbacks to handle HMI events */
	capi_ops.get_capp_info = &phb4_get_capp_info;

	return OPAL_SUCCESS;
}

static int64_t phb4_set_capi_mode(struct phb *phb, uint64_t mode,
				  uint64_t pe_number)
{
	struct phb4 *p = phb_to_phb4(phb);
	struct proc_chip *chip = get_chip(p->chip_id);
	uint64_t reg;
	uint32_t offset;


	if (!capp_ucode_loaded(chip, p->index)) {
		PHBERR(p, "CAPP: ucode not loaded\n");
		return OPAL_RESOURCE;
	}

	lock(&capi_lock);
	chip->capp_phb4_attached_mask |= 1 << p->index;
	unlock(&capi_lock);

	offset = PHB4_CAPP_REG_OFFSET(p);
	xscom_read(p->chip_id, CAPP_ERR_STATUS_CTRL + offset, &reg);
	if ((reg & PPC_BIT(5))) {
		PHBERR(p, "CAPP: recovery failed (%016llx)\n", reg);
		return OPAL_HARDWARE;
	} else if ((reg & PPC_BIT(0)) && (!(reg & PPC_BIT(1)))) {
		PHBDBG(p, "CAPP: recovery in progress\n");
		return OPAL_BUSY;
	}

	switch (mode) {
	case OPAL_PHB_CAPI_MODE_PCIE:
		return OPAL_UNSUPPORTED;

	case OPAL_PHB_CAPI_MODE_CAPI:
		return enable_capi_mode(p, pe_number, CAPI_DMA_TVT0);

	case OPAL_PHB_CAPI_MODE_DMA:
		/* shouldn't be called, enabled by default on p9 */
		return OPAL_UNSUPPORTED;

	case OPAL_PHB_CAPI_MODE_DMA_TVT1:
		return enable_capi_mode(p, pe_number, CAPI_DMA_TVT1);

	case OPAL_PHB_CAPI_MODE_SNOOP_OFF:
		/* shouldn't be called */
		return OPAL_UNSUPPORTED;

	case OPAL_PHB_CAPI_MODE_SNOOP_ON:
		/* nothing to do */
		return OPAL_SUCCESS;
	}

	return OPAL_UNSUPPORTED;
}

static void phb4_p2p_set_initiator(struct phb4 *p, uint16_t pe_number)
{
	uint64_t tve;
	uint16_t window_id = (pe_number << 1) + 1;

	/*
	 * Initiator needs access to the MMIO space of the target,
	 * which is well beyond the 'normal' memory area. Set its TVE
	 * with no range checking.
	 */
	PHBDBG(p, "Setting TVE#1 for peer-to-peer for pe %d\n", pe_number);
	tve = PPC_BIT(51);
	phb4_ioda_sel(p, IODA3_TBL_TVT, window_id, false);
	out_be64(p->regs + PHB_IODA_DATA0, tve);
	p->tve_cache[window_id] = tve;
}

static void phb4_p2p_set_target(struct phb4 *p, bool enable)
{
	uint64_t val;

	/*
	 * Enabling p2p on a target PHB reserves an outbound (as seen
	 * from the CPU) store queue for p2p
	 */
	PHBDBG(p, "%s peer-to-peer\n", (enable ? "Enabling" : "Disabling"));
	xscom_read(p->chip_id,
		p->pe_stk_xscom + XPEC_NEST_STK_PBCQ_MODE, &val);
	if (enable)
		val |= XPEC_NEST_STK_PBCQ_MODE_P2P;
	else
		val &= ~XPEC_NEST_STK_PBCQ_MODE_P2P;
	xscom_write(p->chip_id,
		p->pe_stk_xscom + XPEC_NEST_STK_PBCQ_MODE, val);
}

static void phb4_set_p2p(struct phb *phb, uint64_t mode, uint64_t flags,
			uint16_t pe_number)
{
	struct phb4 *p = phb_to_phb4(phb);

	switch (mode) {
	case OPAL_PCI_P2P_INITIATOR:
		if (flags & OPAL_PCI_P2P_ENABLE)
			phb4_p2p_set_initiator(p, pe_number);
		/*
		 * When disabling p2p on the initiator, we should
		 * reset the TVE to its default bypass setting, but it
		 * is more easily done from the OS, as it knows the
		 * the start and end address and there's already an
		 * opal call for it, so let linux handle it.
		 */
		break;
	case OPAL_PCI_P2P_TARGET:
		phb4_p2p_set_target(p, !!(flags & OPAL_PCI_P2P_ENABLE));
		break;
	default:
		assert(0);
	}
}

static int64_t phb4_set_capp_recovery(struct phb *phb)
{
	struct phb4 *p = phb_to_phb4(phb);

	if (p->flags & PHB4_CAPP_RECOVERY)
		return 0;

	/* set opal event flag to indicate eeh condition */
	opal_update_pending_evt(OPAL_EVENT_PCI_ERROR,
				OPAL_EVENT_PCI_ERROR);

	p->flags |= PHB4_CAPP_RECOVERY;

	return 0;
}

static const struct phb_ops phb4_ops = {
	.cfg_read8		= phb4_pcicfg_read8,
	.cfg_read16		= phb4_pcicfg_read16,
	.cfg_read32		= phb4_pcicfg_read32,
	.cfg_write8		= phb4_pcicfg_write8,
	.cfg_write16		= phb4_pcicfg_write16,
	.cfg_write32		= phb4_pcicfg_write32,
	.choose_bus		= phb4_choose_bus,
	.get_reserved_pe_number	= phb4_get_reserved_pe_number,
	.device_init		= phb4_device_init,
	.device_remove		= NULL,
	.ioda_reset		= phb4_ioda_reset,
	.papr_errinjct_reset	= phb4_papr_errinjct_reset,
	.pci_reinit		= phb4_pci_reinit,
	.set_phb_mem_window	= phb4_set_phb_mem_window,
	.phb_mmio_enable	= phb4_phb_mmio_enable,
	.map_pe_mmio_window	= phb4_map_pe_mmio_window,
	.map_pe_dma_window	= phb4_map_pe_dma_window,
	.map_pe_dma_window_real = phb4_map_pe_dma_window_real,
	.set_xive_pe		= phb4_set_ive_pe,
	.get_msi_32		= phb4_get_msi_32,
	.get_msi_64		= phb4_get_msi_64,
	.set_pe			= phb4_set_pe,
	.set_peltv		= phb4_set_peltv,
	.eeh_freeze_status	= phb4_eeh_freeze_status,
	.eeh_freeze_clear	= phb4_eeh_freeze_clear,
	.eeh_freeze_set		= phb4_eeh_freeze_set,
	.next_error		= phb4_eeh_next_error,
	.err_inject		= phb4_err_inject,
	.get_diag_data		= NULL,
	.get_diag_data2		= phb4_get_diag_data,
	.tce_kill		= phb4_tce_kill,
	.set_capi_mode		= phb4_set_capi_mode,
	.set_p2p		= phb4_set_p2p,
	.set_capp_recovery	= phb4_set_capp_recovery,
};

static void phb4_init_ioda3(struct phb4 *p)
{
	/* Init_18 - Interrupt Notify Base Address */
	out_be64(p->regs + PHB_INT_NOTIFY_ADDR, p->irq_port);

	/* Init_19 - Interrupt Notify Base Index */
	out_be64(p->regs + PHB_INT_NOTIFY_INDEX,
		 xive_get_notify_base(p->base_msi));

	/* Init_19x - Not in spec: Initialize source ID */
	PHBDBG(p, "Reset state SRC_ID: %016llx\n",
	       in_be64(p->regs + PHB_LSI_SOURCE_ID));
	out_be64(p->regs + PHB_LSI_SOURCE_ID,
		 SETFIELD(PHB_LSI_SRC_ID, 0ull, (p->num_irqs - 1) >> 3));

	/* Init_20 - RTT BAR */
	out_be64(p->regs + PHB_RTT_BAR, p->tbl_rtt | PHB_RTT_BAR_ENABLE);

	/* Init_21 - PELT-V BAR */
	out_be64(p->regs + PHB_PELTV_BAR, p->tbl_peltv | PHB_PELTV_BAR_ENABLE);

	/* Init_22 - Setup M32 starting address */
	out_be64(p->regs + PHB_M32_START_ADDR, M32_PCI_START);

	/* Init_23 - Setup PEST BAR */
	out_be64(p->regs + PHB_PEST_BAR,
		 p->tbl_pest | PHB_PEST_BAR_ENABLE);

	/* Init_24 - CRW Base Address Reg */
	/* See enable_capi_mode() */

	/* Init_25 - ASN Compare/Mask */
	/* See enable_capi_mode() */

	/* Init_26 - CAPI Compare/Mask */
	/* See enable_capi_mode() */

	/* Init_27 - PCIE Outbound upper address */
	out_be64(p->regs + PHB_M64_UPPER_BITS, 0);

	/* Init_28 - PHB4 Configuration */
	out_be64(p->regs + PHB_PHB4_CONFIG,
		 PHB_PHB4C_32BIT_MSI_EN |
		 PHB_PHB4C_64BIT_MSI_EN);

	/* Init_29 - At least 256ns delay according to spec. Do a dummy
	 * read first to flush posted writes
	 */
	in_be64(p->regs + PHB_PHB4_CONFIG);
	time_wait_us(2);

	/* Init_30..41 - On-chip IODA tables init */
	phb4_ioda_reset(&p->phb, false);
}

/* phb4_init_rc - Initialize the Root Complex config space
 */
static bool phb4_init_rc_cfg(struct phb4 *p)
{
	int64_t ecap, aercap;

	/* XXX Handle errors ? */

	/* Init_46:
	 *
	 * Set primary bus to 0, secondary to 1 and subordinate to 0xff
	 */
	phb4_pcicfg_write32(&p->phb, 0, PCI_CFG_PRIMARY_BUS, 0x00ff0100);

	/* Init_47 - Clear errors */
	/* see phb4_rc_err_clear() called below */

	/* Init_48
	 *
	 * PCIE Device control/status, enable error reporting, disable relaxed
	 * ordering, set MPS to 128 (see note), clear errors.
	 *
	 * Note: The doc recommends to set MPS to 512. This has proved to have
	 * some issues as it requires specific clamping of MRSS on devices and
	 * we've found devices in the field that misbehave when doing that.
	 *
	 * We currently leave it all to 128 bytes (minimum setting) at init
	 * time. The generic PCIe probing later on might apply a different
	 * value, or the kernel will, but we play it safe at early init
	 */
	if (p->ecap <= 0) {
		ecap = pci_find_cap(&p->phb, 0, PCI_CFG_CAP_ID_EXP);
		if (ecap < 0) {
			PHBERR(p, "Can't locate PCI-E capability\n");
			return false;
		}
		p->ecap = ecap;
	} else {
		ecap = p->ecap;
	}

	phb4_pcicfg_write16(&p->phb, 0, ecap + PCICAP_EXP_DEVCTL,
			     PCICAP_EXP_DEVCTL_CE_REPORT	|
			     PCICAP_EXP_DEVCTL_NFE_REPORT	|
			     PCICAP_EXP_DEVCTL_FE_REPORT	|
			     PCICAP_EXP_DEVCTL_UR_REPORT	|
			     SETFIELD(PCICAP_EXP_DEVCTL_MPS, 0, PCIE_MPS_128B));

	/* Init_49 - Device Control/Status 2 */
	phb4_pcicfg_write16(&p->phb, 0, ecap + PCICAP_EXP_DCTL2,
			     SETFIELD(PCICAP_EXP_DCTL2_CMPTOUT, 0, 0x5) |
			     PCICAP_EXP_DCTL2_ARI_FWD);

	/* Init_50..54
	 *
	 * AER inits
	 */
	if (p->aercap <= 0) {
		aercap = pci_find_ecap(&p->phb, 0, PCIECAP_ID_AER, NULL);
		if (aercap < 0) {
			PHBERR(p, "Can't locate AER capability\n");
			return false;
		}
		p->aercap = aercap;
	} else {
		aercap = p->aercap;
	}

	/* Disable some error reporting as per the PHB4 spec */
	phb4_pcicfg_write32(&p->phb, 0, aercap + PCIECAP_AER_UE_MASK,
			     PCIECAP_AER_UE_POISON_TLP		|
			     PCIECAP_AER_UE_COMPL_TIMEOUT	|
			     PCIECAP_AER_UE_COMPL_ABORT);

	/* Enable ECRC generation & checking */
	phb4_pcicfg_write32(&p->phb, 0, aercap + PCIECAP_AER_CAPCTL,
			     PCIECAP_AER_CAPCTL_ECRCG_EN	|
			     PCIECAP_AER_CAPCTL_ECRCC_EN);

	phb4_rc_err_clear(p);

	return true;
}

static void phb4_init_errors(struct phb4 *p)
{
	/* Init_55..63 - PBL errors */
	out_be64(p->regs + 0x1900,	0xffffffffffffffffull);
	out_be64(p->regs + 0x1908,	0x0000000000000000ull);
	out_be64(p->regs + 0x1920,	0x000000004d1780f8ull);
	out_be64(p->regs + 0x1928,	0x0000000000000000ull);
	if (p->rev == PHB4_REV_NIMBUS_DD10)
		out_be64(p->regs + 0x1930,	0xffffffffb2e87f07ull);
	else
		out_be64(p->regs + 0x1930,	0xffffffffb2f87f07ull);
	out_be64(p->regs + 0x1940,	0x0000000000000000ull);
	out_be64(p->regs + 0x1948,	0x0000000000000000ull);
	out_be64(p->regs + 0x1950,	0x0000000000000000ull);
	out_be64(p->regs + 0x1958,	0x0000000000000000ull);

	/* Init_64..72 - REGB errors */
	out_be64(p->regs + 0x1c00,	0xffffffffffffffffull);
	out_be64(p->regs + 0x1c08,	0x0000000000000000ull);
	/* Enable/disable error status indicators that trigger irqs */
	if (p->has_link) {
		out_be64(p->regs + 0x1c20,	0x2130006efca8bc00ull);
		out_be64(p->regs + 0x1c30,	0xde8fff91035743ffull);
	} else {
		out_be64(p->regs + 0x1c20,	0x0000000000000000ull);
		out_be64(p->regs + 0x1c30,	0x0000000000000000ull);
	}
	out_be64(p->regs + 0x1c28,	0x0000000000000000ull);
	out_be64(p->regs + 0x1c40,	0x0000000000000000ull);
	out_be64(p->regs + 0x1c48,	0x0000000000000000ull);
	out_be64(p->regs + 0x1c50,	0x0000000000000000ull);
	out_be64(p->regs + 0x1c58,	0x0040000000000000ull);

	/* Init_73..81 - TXE errors */
	out_be64(p->regs + 0x0d00,	0xffffffffffffffffull);
	out_be64(p->regs + 0x0d08,	0x0000000000000000ull);
	out_be64(p->regs + 0x0d18,	0xffffff0fffffffffull);
	out_be64(p->regs + 0x0d28,	0x0000400a00000000ull);
	out_be64(p->regs + 0x0d30,	0xdff7fb01f7ddfff0ull); /* XXX CAPI has diff. value */
	out_be64(p->regs + 0x0d40,	0x0000000000000000ull);
	out_be64(p->regs + 0x0d48,	0x0000000000000000ull);
	out_be64(p->regs + 0x0d50,	0x0000000000000000ull);
	out_be64(p->regs + 0x0d58,	0x0000000000000000ull);

	/* Init_82..90 - RXE_ARB errors */
	out_be64(p->regs + 0x0d80,	0xffffffffffffffffull);
	out_be64(p->regs + 0x0d88,	0x0000000000000000ull);
	out_be64(p->regs + 0x0d98,	0xfffffffffbffffffull);
	if (p->rev == PHB4_REV_NIMBUS_DD10)
		out_be64(p->regs + 0x0da8,	0xc00000b801000060ull);
	else
		out_be64(p->regs + 0x0da8,	0xc00008b801000060ull);
	/*
	 * Errata ER20161123 says we should set the top two bits in
	 * 0x0db0 but this causes config space accesses which don't
	 * get a response to fence the PHB. This breaks probing,
	 * hence we don't set them here.
	 */
	out_be64(p->regs + 0x0db0,	0x3bffd703fa7fbf8full); /* XXX CAPI has diff. value */
	out_be64(p->regs + 0x0dc0,	0x0000000000000000ull);
	out_be64(p->regs + 0x0dc8,	0x0000000000000000ull);
	out_be64(p->regs + 0x0dd0,	0x0000000000000000ull);
	out_be64(p->regs + 0x0dd8,	0x0000000004000000ull);

	/* Init_91..99 - RXE_MRG errors */
	out_be64(p->regs + 0x0e00,	0xffffffffffffffffull);
	out_be64(p->regs + 0x0e08,	0x0000000000000000ull);
	out_be64(p->regs + 0x0e18,	0xffffffffffffffffull);
	out_be64(p->regs + 0x0e28,	0x0000600000000000ull);
	if (p->rev == PHB4_REV_NIMBUS_DD10) /* XXX CAPI has diff. value */
		out_be64(p->regs + 0x0e30,	0xffff9effff7fff57ull);
	else
		out_be64(p->regs + 0x0e30,	0xfffffeffff7fff57ull);
	out_be64(p->regs + 0x0e40,	0x0000000000000000ull);
	out_be64(p->regs + 0x0e48,	0x0000000000000000ull);
	out_be64(p->regs + 0x0e50,	0x0000000000000000ull);
	out_be64(p->regs + 0x0e58,	0x0000000000000000ull);

	/* Init_100..108 - RXE_TCE errors */
	out_be64(p->regs + 0x0e80,	0xffffffffffffffffull);
	out_be64(p->regs + 0x0e88,	0x0000000000000000ull);
	out_be64(p->regs + 0x0e98,	0xffffffffffffffffull);
	if (p->rev == PHB4_REV_NIMBUS_DD10)
		out_be64(p->regs + 0x0ea8,	0x6000000000000000ull);
	else
		out_be64(p->regs + 0x0ea8,	0x60000000c0000000ull);
	out_be64(p->regs + 0x0eb0,	0x9faeffaf3fffffffull); /* XXX CAPI has diff. value */
	out_be64(p->regs + 0x0ec0,	0x0000000000000000ull);
	out_be64(p->regs + 0x0ec8,	0x0000000000000000ull);
	out_be64(p->regs + 0x0ed0,	0x0000000000000000ull);
	out_be64(p->regs + 0x0ed8,	0x0000000000000000ull);

	/* Init_109..117 - RXPHB errors */
	out_be64(p->regs + 0x0c80,	0xffffffffffffffffull);
	out_be64(p->regs + 0x0c88,	0x0000000000000000ull);
	out_be64(p->regs + 0x0c98,	0xffffffffffffffffull);
	out_be64(p->regs + 0x0ca8,	0x0000004000000000ull);
	out_be64(p->regs + 0x0cb0,	0x35777033ff000000ull); /* XXX CAPI has diff. value */
	out_be64(p->regs + 0x0cc0,	0x0000000000000000ull);
	out_be64(p->regs + 0x0cc8,	0x0000000000000000ull);
	out_be64(p->regs + 0x0cd0,	0x0000000000000000ull);
	out_be64(p->regs + 0x0cd8,	0x0000000000000000ull);

	/* Init_118..121 - LEM */
	out_be64(p->regs + 0x0c00,	0x0000000000000000ull);
	out_be64(p->regs + 0x0c30,	0xffffffffffffffffull);
	out_be64(p->regs + 0x0c38,	0xffffffffffffffffull);
	out_be64(p->regs + 0x0c40,	0x0000000000000000ull);
}


static bool phb4_wait_dlp_reset(struct phb4 *p)
{
	unsigned int i;
	uint64_t val;

	/*
	 * Firmware cannot access the UTL core regs or PCI config space
	 * until the cores are out of DL_PGRESET.
	 * DL_PGRESET should be polled until it is inactive with a value
	 * of '0'. The recommended polling frequency is once every 1ms.
	 * Firmware should poll at least 200 attempts before giving up.
	 * MMIO Stores to the link are silently dropped by the UTL core if
	 * the link is down.
	 * MMIO Loads to the link will be dropped by the UTL core and will
	 * eventually time-out and will return an all ones response if the
	 * link is down.
	 */
#define DLP_RESET_ATTEMPTS	200

	PHBDBG(p, "Waiting for DLP PG reset to complete...\n");
	for (i = 0; i < DLP_RESET_ATTEMPTS; i++) {
		val = in_be64(p->regs + PHB_PCIE_DLP_TRAIN_CTL);
		if (!(val & PHB_PCIE_DLP_DL_PGRESET))
			break;
		time_wait_ms(1);
	}
	if (val & PHB_PCIE_DLP_DL_PGRESET) {
		PHBERR(p, "Timeout waiting for DLP PG reset !\n");
		return false;
	}
	return true;
}
static void phb4_init_hw(struct phb4 *p, bool first_init)
{
	uint64_t val, creset;

	PHBDBG(p, "Initializing PHB4...\n");

	/* Init_1 - Sync reset
	 *
	 * At this point we assume the PHB has already been reset.
	 */

	/* Init_2 - Mask FIRs */
	out_be64(p->regs + PHB_LEM_ERROR_MASK,			0xffffffffffffffffull);

	/* Init_3 - TCE tag enable */
	out_be64(p->regs + PHB_TCE_TAG_ENABLE,			0xffffffffffffffffull);

	/* Init_4 - PCIE System Configuration Register
	 *
	 * Adjust max speed based on system config
	 */
	val = in_be64(p->regs + PHB_PCIE_SCR);
	PHBDBG(p, "Default system config: 0x%016llx\n", val);
	val = SETFIELD(PHB_PCIE_SCR_MAXLINKSPEED, val, p->max_link_speed);
	out_be64(p->regs + PHB_PCIE_SCR, val);
	PHBDBG(p, "New system config    : 0x%016llx\n",
	       in_be64(p->regs + PHB_PCIE_SCR));

	/* Init_5 - deassert CFG reset */
	creset = in_be64(p->regs + PHB_PCIE_CRESET);
	PHBDBG(p, "Initial PHB CRESET is 0x%016llx\n", creset);
	creset &= ~PHB_PCIE_CRESET_CFG_CORE;
	out_be64(p->regs + PHB_PCIE_CRESET,			creset);

	/* Init_6..13 - PCIE DLP Lane EQ control */
	if (p->lane_eq) {
		out_be64(p->regs + PHB_PCIE_LANE_EQ_CNTL0, be64_to_cpu(p->lane_eq[0]));
		out_be64(p->regs + PHB_PCIE_LANE_EQ_CNTL1, be64_to_cpu(p->lane_eq[1]));
		out_be64(p->regs + PHB_PCIE_LANE_EQ_CNTL2, be64_to_cpu(p->lane_eq[2]));
		out_be64(p->regs + PHB_PCIE_LANE_EQ_CNTL3, be64_to_cpu(p->lane_eq[3]));
		out_be64(p->regs + PHB_PCIE_LANE_EQ_CNTL20, be64_to_cpu(p->lane_eq[4]));
		out_be64(p->regs + PHB_PCIE_LANE_EQ_CNTL21, be64_to_cpu(p->lane_eq[5]));
		if (p->rev == PHB4_REV_NIMBUS_DD10) {
			out_be64(p->regs + PHB_PCIE_LANE_EQ_CNTL22,
				 be64_to_cpu(p->lane_eq[6]));
			out_be64(p->regs + PHB_PCIE_LANE_EQ_CNTL23,
				 be64_to_cpu(p->lane_eq[7]));
		}
	}

	/* Init_14 - Clear link training */
	phb4_pcicfg_write32(&p->phb, 0, 0x78,
			    0x07FE0000 | p->max_link_speed);

	/* Init_15 - deassert cores reset */
	/*
	 * Lift the PHB resets but not PERST, this will be lifted
	 * later by the initial PERST state machine
	 */
	creset &= ~(PHB_PCIE_CRESET_TLDLP | PHB_PCIE_CRESET_PBL);
	creset |= PHB_PCIE_CRESET_PIPE_N;
	out_be64(p->regs + PHB_PCIE_CRESET,			   creset);

	/* Init_16 - Wait for DLP PGRESET to clear */
	if (!phb4_wait_dlp_reset(p))
		goto failed;

	/* Init_17 - PHB Control */
	val = PHB_CTRLR_IRQ_PGSZ_64K;
	if (p->rev == PHB4_REV_NIMBUS_DD10) {
		val |= SETFIELD(PHB_CTRLR_TVT_ADDR_SEL, 0ull, TVT_DD1_2_PER_PE);
	} else {
		val |= SETFIELD(PHB_CTRLR_TVT_ADDR_SEL, 0ull, TVT_2_PER_PE);
		val |= PHB_CTRLR_IRQ_STORE_EOI;
	}

	if (!pci_eeh_mmio)
		val |= PHB_CTRLR_MMIO_EEH_DISABLE;

	out_be64(p->regs + PHB_CTRLR, val);

	/* Init_18..41 - Architected IODA3 inits */
	phb4_init_ioda3(p);

	/* Init_42..45 - Clear DLP error logs */
	out_be64(p->regs + 0x1aa0,			0xffffffffffffffffull);
	out_be64(p->regs + 0x1aa8,			0xffffffffffffffffull);
	out_be64(p->regs + 0x1ab0,			0xffffffffffffffffull);
	out_be64(p->regs + 0x1ab8,			0x0);


	/* Init_46..54 : Init root complex config space */
	if (!phb4_init_rc_cfg(p))
		goto failed;

	/* Init_55..121  : Setup error registers */
	phb4_init_errors(p);

	/* Init_122..123 : Wait for link
	 * NOTE: At this point the spec waits for the link to come up. We
	 * don't bother as we are doing a PERST soon.
	 */

	/* Init_124 :  NBW. XXX TODO */
	/* See enable_capi_mode() */

	/* Init_125 : Setup PCI command/status on root complex
	 * I don't know why the spec does this now and not earlier, so
	 * to be sure to get it right we might want to move it to the freset
	 * state machine, though the generic PCI layer will probably do
	 * this anyway (ie, enable MEM, etc... in the RC)

	 */
	phb4_pcicfg_write16(&p->phb, 0, PCI_CFG_CMD,
			    PCI_CFG_CMD_MEM_EN |
			    PCI_CFG_CMD_BUS_MASTER_EN);

	/* Clear errors */
	phb4_pcicfg_write16(&p->phb, 0, PCI_CFG_STAT,
			    PCI_CFG_STAT_SENT_TABORT |
			    PCI_CFG_STAT_RECV_TABORT |
			    PCI_CFG_STAT_RECV_MABORT |
			    PCI_CFG_STAT_SENT_SERR |
			    PCI_CFG_STAT_RECV_PERR);

	/* Init_126..130 - Re-enable error interrupts */
	out_be64(p->regs + PHB_ERR_IRQ_ENABLE,			0xca8880cc00000000ull);
	out_be64(p->regs + PHB_TXE_ERR_IRQ_ENABLE,		0x2008400e08200000ull);
	out_be64(p->regs + PHB_RXE_ARB_ERR_IRQ_ENABLE,		0xc40028fc01804070ull);
	out_be64(p->regs + PHB_RXE_MRG_ERR_IRQ_ENABLE,		0x00006100008000a8ull);
	if (p->rev == PHB4_REV_NIMBUS_DD10)
		out_be64(p->regs + PHB_RXE_TCE_ERR_IRQ_ENABLE,	0x6051005000000000ull);
	else
		out_be64(p->regs + PHB_RXE_TCE_ERR_IRQ_ENABLE,	0x60510050c0000000ull);

	/* Init_131 - Re-enable LEM error mask */
	out_be64(p->regs + PHB_LEM_ERROR_MASK,			0x0000000000000000ull);


	/* Init_132 - Enable DMA address speculation */
	out_be64(p->regs + PHB_TCE_SPEC_CTL,			0x0000000000000000ull);

	/* Init_133 - Timeout Control Register 1 */
	out_be64(p->regs + PHB_TIMEOUT_CTRL1,			0x0018150000160000ull);

	/* Init_134 - Timeout Control Register 2 */
	out_be64(p->regs + PHB_TIMEOUT_CTRL2,			0x0000181700000000ull);

	/* Init_135 - PBL Timeout Control Register */
	out_be64(p->regs + PHB_PBL_TIMEOUT_CTRL,		0x2015000000000000ull);

	/* Mark the PHB as functional which enables all the various sequences */
	p->state = PHB4_STATE_FUNCTIONAL;

	PHBDBG(p, "Initialization complete\n");

	return;

 failed:
	PHBERR(p, "Initialization failed\n");
	p->state = PHB4_STATE_BROKEN;
}

/* FIXME: Use scoms rather than MMIO incase we are fenced */
static bool phb4_read_capabilities(struct phb4 *p)
{
	uint64_t val;

	/* XXX Should make sure ETU is out of reset ! */

	/* Grab version and fit it in an int */
	val = phb4_read_reg_asb(p, PHB_VERSION);
	if (val == 0 || val == 0xffffffffffffffff) {
		PHBERR(p, "Failed to read version, PHB appears broken\n");
		return false;
	}

	p->rev = ((val >> 16) & 0x00ff0000) | (val & 0xffff);
	PHBDBG(p, "Core revision 0x%x\n", p->rev);

	/* Read EEH capabilities */
	val = in_be64(p->regs + PHB_PHB4_EEH_CAP);
	if (val == 0xffffffffffffffff) {
		PHBERR(p, "Failed to read EEH cap, PHB appears broken\n");
		return false;
	}
	p->max_num_pes = val >> 52;
	if (p->max_num_pes >= 512) {
		p->mrt_size = 16;
		p->mbt_size = 32;
		p->tvt_size = 512;
	} else {
		p->mrt_size = 8;
		p->mbt_size = 16;
		p->tvt_size = 256;
	}
	/* DD2.0 has twice has many TVEs */
	if (p->rev >= PHB4_REV_NIMBUS_DD20)
		p->tvt_size *= 2;

	val = in_be64(p->regs + PHB_PHB4_IRQ_CAP);
	if (val == 0xffffffffffffffff) {
		PHBERR(p, "Failed to read IRQ cap, PHB appears broken\n");
		return false;
	}
	p->num_irqs = val & 0xffff;

	/* This works for 512 PEs.  FIXME calculate for any hardware
	 * size returned above
	 */
	p->tbl_peltv_size = PELTV_TABLE_SIZE_MAX;

	p->tbl_pest_size = p->max_num_pes*16;

	PHBDBG(p, "Found %d max PEs and %d IRQs \n",
	       p->max_num_pes, p->num_irqs);

	return true;
}

static void phb4_allocate_tables(struct phb4 *p)
{
	uint16_t *rte;
	uint32_t i;

	/* XXX Our current memalign implementation sucks,
	 *
	 * It will do the job, however it doesn't support freeing
	 * the memory and wastes space by always allocating twice
	 * as much as requested (size + alignment)
	 */
	p->tbl_rtt = (uint64_t)local_alloc(p->chip_id, RTT_TABLE_SIZE, RTT_TABLE_SIZE);
	assert(p->tbl_rtt);
	rte = (uint16_t *)(p->tbl_rtt);
	for (i = 0; i < RTT_TABLE_ENTRIES; i++, rte++)
		*rte = PHB4_RESERVED_PE_NUM(p);

	p->tbl_peltv = (uint64_t)local_alloc(p->chip_id, p->tbl_peltv_size, p->tbl_peltv_size);
	assert(p->tbl_peltv);
	memset((void *)p->tbl_peltv, 0, p->tbl_peltv_size);

	p->tbl_pest = (uint64_t)local_alloc(p->chip_id, p->tbl_pest_size, p->tbl_pest_size);
	assert(p->tbl_pest);
	memset((void *)p->tbl_pest, 0, p->tbl_pest_size);
}

static void phb4_add_properties(struct phb4 *p)
{
	struct dt_node *np = p->phb.dt_node;
	uint32_t lsibase, icsp = get_ics_phandle();
	uint64_t m32b, m64b, m64s;

	/* Add various properties that HB doesn't have to
	 * add, some of them simply because they result from
	 * policy decisions made in skiboot rather than in HB
	 * such as the MMIO windows going to PCI, interrupts,
	 * etc...
	 */
	dt_add_property_cells(np, "#address-cells", 3);
	dt_add_property_cells(np, "#size-cells", 2);
	dt_add_property_cells(np, "#interrupt-cells", 1);
	dt_add_property_cells(np, "bus-range", 0, 0xff);
	dt_add_property_cells(np, "clock-frequency", 0x200, 0); /* ??? */

	dt_add_property_cells(np, "interrupt-parent", icsp);

	/* XXX FIXME: add slot-name */
	//dt_property_cell("bus-width", 8); /* Figure it out from VPD ? */

	/* "ranges", we only expose M32 (PHB4 doesn't do IO)
	 *
	 * Note: The kernel expects us to have chopped of 64k from the
	 * M32 size (for the 32-bit MSIs). If we don't do that, it will
	 * get confused (OPAL does it)
	 */
	m32b = cleanup_addr(p->mm1_base);
	m64b = cleanup_addr(p->mm0_base);
	m64s = p->mm0_size;
	dt_add_property_cells(np, "ranges",
			      /* M32 space */
			      0x02000000, 0x00000000, M32_PCI_START,
			      hi32(m32b), lo32(m32b), 0, M32_PCI_SIZE - 0x10000);

	/* XXX FIXME: add opal-memwin32, dmawins, etc... */
	dt_add_property_u64s(np, "ibm,opal-m64-window", m64b, m64b, m64s);
	dt_add_property(np, "ibm,opal-single-pe", NULL, 0);
	dt_add_property_cells(np, "ibm,opal-num-pes", p->num_pes);
	dt_add_property_cells(np, "ibm,opal-reserved-pe",
			      PHB4_RESERVED_PE_NUM(p));
	dt_add_property_cells(np, "ibm,opal-msi-ranges",
			      p->base_msi, p->num_irqs - 8);
	/* M64 ranges start at 1 as MBT0 is used for M32 */
	dt_add_property_cells(np, "ibm,opal-available-m64-ranges",
			      1, p->mbt_size - 1);

	/* Tell Linux about alignment limits for segment splits.
	 *
	 * XXX We currently only expose splits of 1 and "num PEs",
	 */
	dt_add_property_cells(np, "ibm,opal-m64-segment-splits",
			      /* Full split, number of segments: */
			      p->num_pes,
			      /* Encoding passed to the enable call */
			      OPAL_ENABLE_M64_SPLIT,
			      /* Alignement/size restriction in #bits*/
			      /* XXX VERIFY VALUE */
			      12,
			      /* Unused */
			      0,
			      /* single PE, number of segments: */
			      1,
			      /* Encoding passed to the enable call */
			      OPAL_ENABLE_M64_NON_SPLIT,
			      /* Alignement/size restriction in #bits*/
			      /* XXX VERIFY VALUE */
			      12,
			      /* Unused */
			      0);

	/* The interrupt maps will be generated in the RC node by the
	 * PCI code based on the content of this structure:
	 */
	lsibase = p->base_lsi;
	p->phb.lstate.int_size = 2;
	p->phb.lstate.int_val[0][0] = lsibase + PHB4_LSI_PCIE_INTA;
	p->phb.lstate.int_val[0][1] = 1;
	p->phb.lstate.int_val[1][0] = lsibase + PHB4_LSI_PCIE_INTB;
	p->phb.lstate.int_val[1][1] = 1;
	p->phb.lstate.int_val[2][0] = lsibase + PHB4_LSI_PCIE_INTC;
	p->phb.lstate.int_val[2][1] = 1;
	p->phb.lstate.int_val[3][0] = lsibase + PHB4_LSI_PCIE_INTD;
	p->phb.lstate.int_val[3][1] = 1;
	p->phb.lstate.int_parent[0] = icsp;
	p->phb.lstate.int_parent[1] = icsp;
	p->phb.lstate.int_parent[2] = icsp;
	p->phb.lstate.int_parent[3] = icsp;

	/* Indicators for variable tables */
	dt_add_property_cells(np, "ibm,opal-rtt-table",
		hi32(p->tbl_rtt), lo32(p->tbl_rtt), RTT_TABLE_SIZE);
	dt_add_property_cells(np, "ibm,opal-peltv-table",
		hi32(p->tbl_peltv), lo32(p->tbl_peltv), p->tbl_peltv_size);
	dt_add_property_cells(np, "ibm,opal-pest-table",
		hi32(p->tbl_pest), lo32(p->tbl_pest), p->tbl_pest_size);

	dt_add_property_cells(np, "ibm,phb-diag-data-size",
			      sizeof(struct OpalIoPhb4ErrorData));

	/* Indicate to Linux that CAPP timebase sync is supported */
	dt_add_property_string(np, "ibm,capp-timebase-sync", NULL);
}

static bool phb4_calculate_windows(struct phb4 *p)
{
	const struct dt_property *prop;

	/* Get PBCQ MMIO windows from device-tree */
	prop = dt_require_property(p->phb.dt_node,
				   "ibm,mmio-windows", -1);
	assert(prop->len >= (2 * sizeof(uint64_t)));

	p->mm0_base = ((const uint64_t *)prop->prop)[0];
	p->mm0_size = ((const uint64_t *)prop->prop)[1];
	if (prop->len > 16) {
		p->mm1_base = ((const uint64_t *)prop->prop)[2];
		p->mm1_size = ((const uint64_t *)prop->prop)[3];
	}

	/* Sort them so that 0 is big and 1 is small */
	if (p->mm1_size && p->mm1_size > p->mm0_size) {
		uint64_t b = p->mm0_base;
		uint64_t s = p->mm0_size;
		p->mm0_base = p->mm1_base;
		p->mm0_size = p->mm1_size;
		p->mm1_base = b;
		p->mm1_size = s;
	}

	/* If 1 is too small, ditch it */
	if (p->mm1_size < M32_PCI_SIZE)
		p->mm1_size = 0;

	/* If 1 doesn't exist, carve it out of 0 */
	if (p->mm1_size == 0) {
		p->mm0_size /= 2;
		p->mm1_base = p->mm0_base + p->mm0_size;
		p->mm1_size = p->mm0_size;
	}

	/* Crop mm1 to our desired size */
	if (p->mm1_size > M32_PCI_SIZE)
		p->mm1_size = M32_PCI_SIZE;

	return true;
}

static void phb4_err_interrupt(struct irq_source *is, uint32_t isn)
{
	struct phb4 *p = is->data;

	PHBDBG(p, "Got interrupt 0x%08x\n", isn);

#if 0
	/* Update pending event */
	opal_update_pending_evt(OPAL_EVENT_PCI_ERROR,
				OPAL_EVENT_PCI_ERROR);

	/* If the PHB is broken, go away */
	if (p->state == PHB3_STATE_BROKEN)
		return;

	/*
	 * Mark the PHB has pending error so that the OS
	 * can handle it at late point.
	 */
	phb3_set_err_pending(p, true);
#endif
}

static uint64_t phb4_lsi_attributes(struct irq_source *is __unused,
				uint32_t isn __unused)
{
#ifndef DISABLE_ERR_INTS
	struct phb3 *p = is->data;
	uint32_t idx = isn - p->base_lsi;

	if (idx == PHB3_LSI_PCIE_INF || idx == PHB3_LSI_PCIE_ER)
		return IRQ_ATTR_TARGET_OPAL | IRQ_ATTR_TARGET_RARE;
#endif
	return IRQ_ATTR_TARGET_LINUX;
}

static int64_t phb4_ndd1_lsi_set_xive(struct irq_source *is, uint32_t isn,
				     uint16_t server, uint8_t priority)
{
	struct phb4 *p = is->data;
	uint32_t idx = isn - p->base_lsi;

	if (idx > 8)
		return OPAL_PARAMETER;

	phb_lock(&p->phb);

	phb4_ioda_sel(p, IODA3_TBL_LIST, idx, false);

	/* Mask using P=0,Q=1, unmask using P=1,Q=0 followed by EOI */
	/* XXX FIXME: A quick mask/umask can make us shoot an interrupt
	 * more than once to a queue. We need to keep track better.
	 *
	 * Thankfully, this is only on Nimubs DD1 and for LSIs, so
	 * will go away soon enough.
	 */
	if (priority == 0xff)
		out_be64(p->regs + PHB_IODA_DATA0, IODA3_LIST_Q);
	else {
		out_be64(p->regs + PHB_IODA_DATA0, IODA3_LIST_P);
		__irq_source_eoi(is, isn);
	}

	phb_unlock(&p->phb);

	return 0;
}

static const struct irq_source_ops phb4_ndd1_lsi_ops = {
	.set_xive = phb4_ndd1_lsi_set_xive,
	.interrupt = phb4_err_interrupt,
	.attributes = phb4_lsi_attributes,
};

static const struct irq_source_ops phb4_lsi_ops = {
	.interrupt = phb4_err_interrupt,
	.attributes = phb4_lsi_attributes,
};

#ifdef HAVE_BIG_ENDIAN
static u64 lane_eq_default[8] = {
	0x7777777777777777, 0x7777777777777777,
	0x7777777777777777, 0x7777777777777777,
	0x7777777777777777, 0x7777777777777777,
	0x7777777777777777, 0x7777777777777777
};
#else
#error lane_eq_default needs to be big endian (device tree property)
#endif

static void phb4_create(struct dt_node *np)
{
	const struct dt_property *prop;
	struct phb4 *p = zalloc(sizeof(struct phb4));
	struct pci_slot *slot;
	size_t lane_eq_len, lane_eq_len_req;
	struct dt_node *iplp;
	char *path;
	uint32_t irq_base, irq_flags;
	int i;
	struct proc_chip *chip;

	assert(p);

	/* Populate base stuff */
	p->index = dt_prop_get_u32(np, "ibm,phb-index");
	p->chip_id = dt_prop_get_u32(np, "ibm,chip-id");
	chip = get_chip(p->chip_id);
	p->regs = (void *)dt_get_address(np, 0, NULL);
	p->int_mmio = (void *)dt_get_address(np, 1, NULL);
	p->phb.dt_node = np;
	p->phb.ops = &phb4_ops;
	p->phb.phb_type = phb_type_pcie_v4;
	p->phb.scan_map = 0x1; /* Only device 0 to scan */
	p->state = PHB4_STATE_UNINITIALIZED;

	if (!phb4_calculate_windows(p))
		return;

	/* Get the various XSCOM register bases from the device-tree */
	prop = dt_require_property(np, "ibm,xscom-bases", 5 * sizeof(uint32_t));
	p->pe_xscom = ((const uint32_t *)prop->prop)[0];
	p->pe_stk_xscom = ((const uint32_t *)prop->prop)[1];
	p->pci_xscom = ((const uint32_t *)prop->prop)[2];
	p->pci_stk_xscom = ((const uint32_t *)prop->prop)[3];
	p->etu_xscom = ((const uint32_t *)prop->prop)[4];

	/*
	 * We skip the initial PERST assertion requested by the generic code
	 * when doing a cold boot because we are coming out of cold boot already
	 * so we save boot time that way. The PERST state machine will still
	 * handle waiting for the link to come up, it will just avoid actually
	 * asserting & deasserting the PERST output
	 *
	 * For a hot IPL, we still do a PERST
	 *
	 * Note: In absence of property (ie, FSP-less), we stick to the old
	 * behaviour and set skip_perst to true
	 */
	p->skip_perst = true; /* Default */

	iplp = dt_find_by_path(dt_root, "ipl-params/ipl-params");
	if (iplp) {
		const char *ipl_type = dt_prop_get_def(iplp, "cec-major-type", NULL);
		if (ipl_type && (!strcmp(ipl_type, "hot")))
			p->skip_perst = false;
	}

	/* By default link is assumed down */
	p->has_link = false;

	/* We register the PHB before we initialize it so we
	 * get a useful OPAL ID for it
	 */
	pci_register_phb(&p->phb, phb4_get_opal_id(p->chip_id, p->index));

	/* Create slot structure */
	slot = phb4_slot_create(&p->phb);
	if (!slot)
		PHBERR(p, "Cannot create PHB slot\n");

	/* Hello ! */
	path = dt_get_path(np);
	PHBINF(p, "Found %s @%p\n", path, p->regs);
	PHBINF(p, "  M32 [0x%016llx..0x%016llx]\n",
	       p->mm1_base, p->mm1_base + p->mm1_size - 1);
	PHBINF(p, "  M64 [0x%016llx..0x%016llx]\n",
	       p->mm0_base, p->mm0_base + p->mm0_size - 1);
	free(path);

	/* Find base location code from root node */
	p->phb.base_loc_code = dt_prop_get_def(dt_root,
					       "ibm,io-base-loc-code", NULL);
	if (!p->phb.base_loc_code)
		PHBDBG(p, "Base location code not found !\n");

	/*
	 * Grab CEC IO VPD load info from the root of the device-tree,
	 * on P8 there's a single such VPD for the whole machine
	 */
	prop = dt_find_property(dt_root, "ibm,io-vpd");
	if (!prop) {
		/* LX VPD Lid not already loaded */
		vpd_iohub_load(dt_root);
	}

	/* Obtain informatin about the PHB from the hardware directly */
	if (!phb4_read_capabilities(p))
		goto failed;

	/* Priority order: NVRAM -> dt -> GEN2 dd1 -> GEN3 dd2.00 -> GEN4 */
	p->max_link_speed = 4;
	if (p->rev == PHB4_REV_NIMBUS_DD10)
		p->max_link_speed = 2;
	if (p->rev == PHB4_REV_NIMBUS_DD20 &&
	    ((0xf & chip->ec_level) == 0) && chip->ec_rev == 0)
		p->max_link_speed = 3;
	if (dt_has_node_property(np, "ibm,max-link-speed", NULL))
		p->max_link_speed = dt_prop_get_u32(np, "ibm,max-link-speed");
	if (pcie_max_link_speed)
		p->max_link_speed = pcie_max_link_speed;
	if (p->max_link_speed > 4) /* clamp to 4 */
		p->max_link_speed = 4;
	PHBINF(p, "Max link speed: GEN%i\n", p->max_link_speed);

	/* Check for lane equalization values from HB or HDAT */
	p->lane_eq = dt_prop_get_def_size(np, "ibm,lane-eq", NULL, &lane_eq_len);
	if (p->rev == PHB4_REV_NIMBUS_DD10)
		lane_eq_len_req = 8 * 8;
	else
		lane_eq_len_req = 6 * 8;
	if (p->lane_eq) {
		if (lane_eq_len < lane_eq_len_req) {
			PHBERR(p, "Device-tree has ibm,lane-eq too short: %ld"
			       " (want %ld)\n", lane_eq_len, lane_eq_len_req);
			p->lane_eq = NULL;
		}
	} else {
		PHBDBG(p, "Using default lane equalization settings\n");
		p->lane_eq = lane_eq_default;
	}
	if (p->lane_eq) {
		PHBDBG(p, "Override lane equalization settings:\n");
		for (i = 0 ; i < lane_eq_len_req/(8 * 2) ; i++)
			PHBDBG(p, "  0x%016llx 0x%016llx\n",
			       be64_to_cpu(p->lane_eq[2 * i]),
			       be64_to_cpu(p->lane_eq[2 * i + 1]));
	}

	/* Allocate a block of interrupts. We need to know if it needs
	 * 2K or 4K interrupts ... for now we just use 4K but that
	 * needs to be fixed
	 */
	irq_base = xive_alloc_hw_irqs(p->chip_id, p->num_irqs, p->num_irqs);
	if (irq_base == XIVE_IRQ_ERROR) {
		PHBERR(p, "Failed to allocate %d interrupt sources\n",
		       p->num_irqs);
		goto failed;
	}
	p->base_msi = irq_base;
	p->base_lsi = irq_base + p->num_irqs - 8;
	p->irq_port = xive_get_notify_port(p->chip_id,
					   XIVE_HW_SRC_PHBn(p->index));

	if (p->rev == PHB4_REV_NIMBUS_DD10)
		p->num_pes = p->max_num_pes/2;
	else
		p->num_pes = p->max_num_pes;

	/* Allocate the SkiBoot internal in-memory tables for the PHB */
	phb4_allocate_tables(p);

	phb4_add_properties(p);

	/* Clear IODA3 cache */
	phb4_init_ioda_cache(p);

	/* Get the HW up and running */
	phb4_init_hw(p, true);

	/* Load capp microcode into capp unit */
	load_capp_ucode(p);

	/* Register all interrupt sources with XIVE */
	irq_flags = XIVE_SRC_SHIFT_BUG | XIVE_SRC_TRIGGER_PAGE;
	if (p->rev >= PHB4_REV_NIMBUS_DD20)
		irq_flags |= XIVE_SRC_STORE_EOI;
	xive_register_hw_source(p->base_msi, p->num_irqs - 8, 16,
				p->int_mmio, irq_flags, NULL, NULL);

	xive_register_hw_source(p->base_lsi, 8, 16,
				p->int_mmio + ((p->num_irqs - 8) << 16),
				XIVE_SRC_LSI | XIVE_SRC_SHIFT_BUG,
				p,
				(p->rev == PHB4_REV_NIMBUS_DD10) ?
				&phb4_ndd1_lsi_ops : &phb4_lsi_ops);

	/* Platform additional setup */
	if (platform.pci_setup_phb)
		platform.pci_setup_phb(&p->phb, p->index);

	dt_add_property_string(np, "status", "okay");

	return;

 failed:
	p->state = PHB4_STATE_BROKEN;

	/* Tell Linux it's broken */
	dt_add_property_string(np, "status", "error");
}

static void phb4_probe_stack(struct dt_node *stk_node, uint32_t pec_index,
			     uint32_t nest_base, uint32_t pci_base)
{
	uint32_t pci_stack, nest_stack, etu_base, gcid, phb_num, stk_index;
	uint64_t val, phb_bar = 0, irq_bar = 0, bar_en;
	uint64_t mmio0_bar = 0, mmio0_bmask, mmio0_sz;
	uint64_t mmio1_bar, mmio1_bmask, mmio1_sz;
	uint64_t reg[4];
	void *foo;
	uint64_t mmio_win[4];
	unsigned int mmio_win_sz;
	struct dt_node *np;
	char *path;
	uint64_t capp_ucode_base;
	unsigned int max_link_speed;

	gcid = dt_get_chip_id(stk_node);
	stk_index = dt_prop_get_u32(stk_node, "reg");
	phb_num = dt_prop_get_u32(stk_node, "ibm,phb-index");
	path = dt_get_path(stk_node);
	prlog(PR_INFO, "PHB: Chip %d Found PHB4 PBCQ%d Stack %d at %s\n",
	      gcid, pec_index, stk_index, path);
	free(path);

	pci_stack = pci_base + 0x40 * (stk_index + 1);
	nest_stack = nest_base + 0x40 * (stk_index + 1);
	etu_base = pci_base + 0x100 + 0x40 * stk_index;

	prlog(PR_DEBUG, "PHB[%d:%d] X[PE]=0x%08x/0x%08x X[PCI]=0x%08x/0x%08x X[ETU]=0x%08x\n",
	      gcid, phb_num, nest_base, nest_stack, pci_base, pci_stack, etu_base);

	/* Default BAR enables */
	bar_en = 0;

	/* Initialize PHB register BAR */
	phys_map_get(gcid, PHB4_REG_SPC, phb_num, &phb_bar, NULL);
	xscom_write(gcid, nest_stack + XPEC_NEST_STK_PHB_REG_BAR, phb_bar << 8);
	bar_en |= XPEC_NEST_STK_BAR_EN_PHB;


	/* Same with INT BAR (ESB) */
	phys_map_get(gcid, PHB4_XIVE_ESB, phb_num, &irq_bar, NULL);
	xscom_write(gcid, nest_stack + XPEC_NEST_STK_IRQ_BAR, irq_bar << 8);
	bar_en |= XPEC_NEST_STK_BAR_EN_INT;


	/* Same with MMIO windows */
	phys_map_get(gcid, PHB4_64BIT_MMIO, phb_num, &mmio0_bar, &mmio0_sz);
	mmio0_bmask =  (~(mmio0_sz - 1)) & 0x00FFFFFFFFFFFFFFULL;
	xscom_write(gcid, nest_stack + XPEC_NEST_STK_MMIO_BAR0, mmio0_bar << 8);
	xscom_write(gcid, nest_stack + XPEC_NEST_STK_MMIO_BAR0_MASK, mmio0_bmask << 8);

	phys_map_get(gcid, PHB4_32BIT_MMIO, phb_num, &mmio1_bar, &mmio1_sz);
	mmio1_bmask =  (~(mmio1_sz - 1)) & 0x00FFFFFFFFFFFFFFULL;
	xscom_write(gcid, nest_stack + XPEC_NEST_STK_MMIO_BAR1, mmio1_bar << 8);
	xscom_write(gcid, nest_stack + XPEC_NEST_STK_MMIO_BAR1_MASK, mmio1_bmask << 8);
	bar_en |= XPEC_NEST_STK_BAR_EN_MMIO0 | XPEC_NEST_STK_BAR_EN_MMIO1;

	/* Build MMIO windows list */
	mmio_win_sz = 0;
	if (mmio0_bar) {
		mmio_win[mmio_win_sz++] = mmio0_bar;
		mmio_win[mmio_win_sz++] = mmio0_sz;
		bar_en |= XPEC_NEST_STK_BAR_EN_MMIO0;
	}
	if (mmio1_bar) {
		mmio_win[mmio_win_sz++] = mmio1_bar;
		mmio_win[mmio_win_sz++] = mmio1_sz;
		bar_en |= XPEC_NEST_STK_BAR_EN_MMIO1;
	}

	/* Set the appropriate enables */
	xscom_read(gcid, nest_stack + XPEC_NEST_STK_BAR_EN, &val);
	val |= bar_en;
	xscom_write(gcid, nest_stack + XPEC_NEST_STK_BAR_EN, val);

	/* No MMIO windows ? Barf ! */
	if (mmio_win_sz == 0) {
		prerror("PHB[%d:%d] No MMIO windows enabled !\n", gcid, phb_num);
		return;
	}

	/* Check ETU reset */
	xscom_read(gcid, pci_stack + XPEC_PCI_STK_ETU_RESET, &val);
	prlog_once(PR_DEBUG, "ETU reset: %llx\n", val);
	xscom_write(gcid, pci_stack + XPEC_PCI_STK_ETU_RESET, 0);
	time_wait_ms(1);

	// show we can read phb mmio space
	foo = (void *)(phb_bar + 0x800); // phb version register
	prlog_once(PR_DEBUG, "Version reg: 0x%016llx\n", in_be64(foo));

	/* Create PHB node */
	reg[0] = phb_bar;
	reg[1] = 0x1000;
	reg[2] = irq_bar;
	reg[3] = 0x10000000;

	np = dt_new_addr(dt_root, "pciex", reg[0]);
	if (!np)
		return;

	dt_add_property_strings(np, "compatible", "ibm,power9-pciex", "ibm,ioda3-phb");
	dt_add_property_strings(np, "device_type", "pciex");
	dt_add_property(np, "reg", reg, sizeof(reg));

	/* Everything else is handled later by skiboot, we just
	 * stick a few hints here
	 */
	dt_add_property_cells(np, "ibm,xscom-bases",
			      nest_base, nest_stack, pci_base, pci_stack, etu_base);
	dt_add_property(np, "ibm,mmio-windows", mmio_win, 8 * mmio_win_sz);
	dt_add_property_cells(np, "ibm,phb-index", phb_num);
	dt_add_property_cells(np, "ibm,phb-stack", stk_node->phandle);
	dt_add_property_cells(np, "ibm,phb-stack-index", stk_index);
	dt_add_property_cells(np, "ibm,chip-id", gcid);
	if (dt_has_node_property(stk_node, "ibm,hub-id", NULL))
		dt_add_property_cells(np, "ibm,hub-id",
				      dt_prop_get_u32(stk_node, "ibm,hub-id"));
	if (dt_has_node_property(stk_node, "ibm,loc-code", NULL)) {
		const char *lc = dt_prop_get(stk_node, "ibm,loc-code");
		dt_add_property_string(np, "ibm,loc-code", lc);
	}
	if (dt_has_node_property(stk_node, "ibm,lane-eq", NULL)) {
		size_t leq_size;
		const void *leq = dt_prop_get_def_size(stk_node, "ibm,lane-eq",
						       NULL, &leq_size);
		if (leq != NULL && leq_size == 4 * 8)
			dt_add_property(np, "ibm,lane-eq", leq, leq_size);
	}
	if (dt_has_node_property(stk_node, "ibm,capp-ucode", NULL)) {
		capp_ucode_base = dt_prop_get_u32(stk_node, "ibm,capp-ucode");
		dt_add_property_cells(np, "ibm,capp-ucode", capp_ucode_base);
	}
	if (dt_has_node_property(stk_node, "ibm,max-link-speed", NULL)) {
		max_link_speed = dt_prop_get_u32(stk_node, "ibm,max-link-speed");
		dt_add_property_cells(np, "ibm,max-link-speed", max_link_speed);
	}
	dt_add_property_cells(np, "ibm,capi-flags",
			      OPAL_PHB_CAPI_FLAG_SNOOP_CONTROL);

	add_chip_dev_associativity(np);
}

static void phb4_probe_pbcq(struct dt_node *pbcq)
{
	uint32_t nest_base, pci_base, pec_index;
	struct dt_node *stk;

	nest_base = dt_get_address(pbcq, 0, NULL);
	pci_base = dt_get_address(pbcq, 1, NULL);
	pec_index = dt_prop_get_u32(pbcq, "ibm,pec-index");

	dt_for_each_child(pbcq, stk) {
		if (dt_node_is_enabled(stk))
			phb4_probe_stack(stk, pec_index, nest_base, pci_base);
	}
}

void probe_phb4(void)
{
	struct dt_node *np;

	verbose_eeh = nvram_query_eq("pci-eeh-verbose", "true");
	/* REMOVEME: force this for now until we stabalise PCIe */
	verbose_eeh = 1;
	if (verbose_eeh)
		prlog(PR_INFO, "PHB4: Verbose EEH enabled\n");

	pci_tracing = nvram_query_eq("pci-tracing", "true");
	pci_eeh_mmio = !nvram_query_eq("pci-eeh-mmio", "disabled");
	pci_retry_all = nvram_query_eq("pci-retry-all", "true");

	/* Look for PBCQ XSCOM nodes */
	dt_for_each_compatible(dt_root, np, "ibm,power9-pbcq")
		phb4_probe_pbcq(np);

	/* Look for newly created PHB nodes */
	dt_for_each_compatible(dt_root, np, "ibm,power9-pciex")
		phb4_create(np);
}