- Follow general CGM hygiene and setting sensor recommendation here.
-
Recent transmitters are called Firefly. Sensors cannot be restarted without removing the transmitter, which itself cannot be reset, they also do not generate raw data.
-
If you are restarting sensors, ensure you are ready to calibrate and keep an eye on variation.
-
Fabrika kalibrasyonu ile "Pre-soaking" ön ısınma denilen sensörü daha önce verici olmadan doku sıvısına "alışacak" şekilde yerleştirmek, muhtemelen glikoz değerlerinde sapmalara yol açar. 'pre-soak' ön ısınma yapıyorsanız, en iyi sonuçları almak için muhtemelen sensörü kalibre etmeniz gerekecektir.
Read more in the article published by Tim Street at www.diabettech.com.
-
If you are using a recent (Firefly) transmitter, preemptive restarts are ignored.
-
If you are using a modded transmitter you do not need to use preemptive restarts.
-
If you are using an old rebatteried transmitter, the safest thing to do is disable preemptive restarts. Though, in this case you will have to use the G6 in non-native mode (which is unadvisable as it disables factory calibration and doesn't filter noisy readings), or else the sensor will stop after 10 days.
-
Dexcom G6 vericisi, Dexcom alıcısına (veya alternatif olarak t:slim pompasına) ve telefonunuzdaki bir uygulamaya aynı anda bağlanabilir.
-
When using xDrip+ as receiver uninstall the Dexcom app first. You cannot connect xDrip+ and Dexcom app with the transmitter at the same time!
-
If you need Clarity and want to profit from xDrip+ alarms use the BYODA with local broadcast to xDrip+. You can also use xDrip+ as a companion app of the official Dexcom app, but you might experience delays in BG readings.
-
If not already set up, download xDrip+ and follow the instructions on xDrip+ settings page.
-
Select xDrip+ in in ConfigBuilder, BG Source.
-
Adjust settings in xDrip+ according to xDrip+ settings page
(DexcomG6-if-using-g6-with-build-your-own-dexcom-app)=
- Build Your Own Dexcom App (BYODA) supports local broadcast to AAPS and/or xDrip+ (not for G5/ONE/G7 sensors!)
- Bu uygulama, Dexcom G6'nızı herhangi bir Android akıllı telefonla kullanmanızı sağlar.
- Uninstall the original Dexcom app or patched Dexcom app if you used one of those previously (do not stop the currently running sensor)
- Install the downloaded apk
- Yamalı uygulamada sensör kodunu ve verici seri numarasını girin.
- In phone settings go to apps > Dexcom G6 > permissions > additional permissions and press 'Access Dexcom app'.
- Kısa bir süre sonra BYODA verici sinyalini almalıdır.
-
Select 'Dexcom App (patched)' in in ConfigBuilder, BG Source.
-
If you don't receive any values select any other data source, then re-select 'Dexcom App (patched)' to trigger the demand for permissions to establish the connection between AAPS and BYODA-broadcast.
- Veri kaynağı olarak '640G/Everses'i seçin.
- Command 'start sensor' must be performed in xDrip+ in order to receive values. This will not affect your current sensor controlled by Build Your Own Dexcom App.
(DexcomG6-troubleshooting-g6)=
- Scroll down to Troubleshooting here.
General Troubleshooting for CGMs can be found here.
If you happen to change transmitter during a running sensor session you might try to remove the transmitter without damaging the sensor mount. A video can be found here. If you opt for this solution instead, you must be careful to avoid damaging sensor contacts with the strip.