emonLibCM.cpp

/*
  emonLibCM.cpp - Library for openenergymonitor
  GNU GPL
*/

// This library provides continuous single-phase monitoring of real power on up to five CT channels.
// All of the time-critical code is now contained within the ISR, only the slower activities
// are done within the main code. These slower activities include RF transmissions,
// and all Serial statements (not part of the library).  
//
// This library is suitable for either 50 or 60 Hz operation.
//
// Original Author: Robin Emley (calypso_rae on Open Energy Monitor Forum)
// Addition of Wh totals by: Trystan Lea
// Heavily modified to improve performance and calibration; temperature measurement 
//  and pulse counting incorporated into the library,  by Robert Wall 
//  Release for testing 4/1/2017
//
// Version 2.0  21/11/2018
// Version 2.01  3/12/2018  Calculation error in phase error correction - const.'360' missing, 'x' & 'y' coefficients swapped.
// Version 2.02 13/07/2019  Temperature measurement: Added "BAD_TEMPERATURE" return value when reporting period < 0.2 s, 
//                            getLogicalChannel( ), ReCalibrate_VChannel( ), ReCalibrate_IChannel( ) added, setPulsePin( ) interrupt no. was obligatory,
//                            pulse & temperatures were set/enabled only at startup, setTemperatureDataPin was ineffective, preloaded sensor addresses
//                            not handled properly.
//              18/10/2019  Sketch using this became the default in emonTx V3.4
// Version 2.03 25/10/2019  Mains Frequency reporting [getLineFrequency( )]added, 
//                            ADC reference source was AVcc and not selectable - ability to select [setADC_VRef( )] added, 
//                            sampleSetsDuringThisDatalogPeriod (and derivatives) was samplesDuringThisDatalogPeriod etc,
//                            Energy calculation changed to use internal clock rather than mains time by addition of "frequencyDeviation".
// Version 2.04 1/8/2020    In examples, 'else' added to "if (EmonLibCM_Ready())" to keep JeeLib alive. Example for RFM69CW only ('Classic' format) and 
//                            not using JeeLib added.
//                            getDatalog_period( ) added. Temperature array is now ignored if first device is not a DS18B20. 'BAD_TEMPERATURE' now returned if
//                            sensor address is made invalid during operation. Array above is sensor count is filled with UNUSED_TEMPERATURE. Superfluous 'if' 
//                            removed at end of retrieveTemperatures() - power pin is now set low regardless. 'else' added to 'if' in
//                            (if (temperatureEnabled = _enable)) in TemperatureEnable( ) to ensure power is off if not required, delay after retrieving 
//                            a temperature was 5 ms. 
//                            unsigned long missing_VoltageSamples (was "missing_Voltage"), bool firstcycle were not volatile, unnecessary copies of 
//                            'protected' variables removed, datalog period was set only at startup & minimum limit added. cycleCountForDatalogging, 
//                            min_startup_cycles were signed. 
//                            (Plus some cosmetic changes)
// Version 2.1.0 9/7/2021   2nd pulse input added, array of structs was individual variables. N.B. The definition setPulsePin(byte channel, int _pin) 
//                            is incompatible with the old definition of setPulsePin(int _pin, int _interrupt). Solution for 85 °C problem added, 
//                            special print format for emonPi added.  'Setters' to initialise Wh counters & pulse count added. If no a.c. voltage, 
//                            now uses assumed Vrms to calculate power, VA & energy, p.f. and frequency both report zero. Error in phase shift calculation 
//                            meant wrong correction was applied when ct's were sampled out of sequence.
//  


// #include "WProgram.h" un-comment for use on older versions of Arduino IDE

// #define SAMPPIN 5           // EmonTx: Preferred pin for testing. This MUST be commented out if the temperature sensor power is connected here. Only include for testing.
// #define SAMPPIN 19          // EmonTx: Alternative pin for testing. This MUST be commented out if the temperature sensor power is connected here. Only include for testing.
// #define INTPINS             // Debugging print of interrupt allocations

#include "emonLibCM.h"

#if defined(ARDUINO) && ARDUINO >= 100

#include "Arduino.h"

#else

#include "WProgram.h"

#endif




unsigned int cycles_per_second = 50;                                   // mains frequency in Hz (i.e. 50 or 60)
float datalog_period_in_seconds = 10.0;
unsigned int min_startup_cycles = 10;

// Maximum number of Current (I) channels used to create arrays
static const int max_no_of_channels = 5;

// User set number of Current (I) channels used by 'for' loops
int no_of_channels = 4;
// number of Current (I) channels that have been set
byte no_of_Iinputs = 0;

// for general interaction between the main code and the ISR
volatile boolean datalogEventPending;
volatile unsigned long missing_VoltageSamples = 0;                     // provides a timebase mechanism for current-only use
                                                                       //  - uses the ADC free-running rate as a clock.
double line_frequency;                                                 // Timed from sample rate & cycle count

                                                                       
// Arrays for current channels (zero-based)                                                                       
int realPower_CT[max_no_of_channels];
int apparentPower_CT[max_no_of_channels];
double Irms_CT[max_no_of_channels];
long wh_CT[max_no_of_channels] = {0, 0, 0, 0, 0};
double pf[max_no_of_channels];
double Vrms;
volatile boolean ChannelInUse[max_no_of_channels];
static byte lChannel[max_no_of_channels+1];                            // logical current channel no. (0-based)
    
// analogue ports
static byte ADC_Sequence[max_no_of_channels+1] = {0,1,2,3,4,5};        // <-- Sequence in which the analogue ports are scanned, first is Voltage, remainder are currents
// ADC data
int ADCBits = 10;                                                      // 10 for the emonTx and most of the Arduino range, 12 for the Arduino Due.
double Vref = 3.3;                                                     // ADC Reference Voltage = 3.3 for emonTX, 5.0 for most of the Arduino range.
int ADCDuration = 104;                                                 // Time in microseconds for one ADC conversion = 104 for 16 MHz clock 
byte ADCRef = VREF_NORMAL  << 6;                                       // ADC Reference: VREF_EXTERNAL, VREF_NORMAL = AVcc, VREF_INTERNAL = Internal 1.1 V

// Pulse Counting

#define PULSEINPUTS 2                // No of available interrupts for pulse counting (2 is the maximum, add more "onPulse..." functions for more)

struct pulse {

  bool PulseEnabled = false;
  bool PulseChange = false;                                            // track change of state of counting
  void (*pulseISR)();
  byte PulsePin = 3;                                                   // default to DI3 for the emonTx V3
  byte PulseInterrupt = 1;                                             // default to int1 for the emonTx V3
  unsigned long PulseMinPeriod = 110;                                  // default to 110 ms
  unsigned long pulseCount = 0;                                        // Total number of pulses from switch-on 
  volatile unsigned long pulseIncrement = 0;                           // Incremental number of pulses between readings
  unsigned long pulseTime;                                             // Instant of the last pulse - used for debounce logic
} pulses[PULSEINPUTS];

void onPulse(byte channel);                                            // General pulse handler
void onPulse0(), onPulse1();                                           // Individual pulse handlers - one per interrupt

// Set-up values
//--------------
// These set up the library for different hardware configurations
//
// setADC                    Sets the ADC resolution and the conversion time
// cycles_per_second         Defines the mains frequency
// _min_startup_cycles       The period of inactivity whilst the system settles at start-up
// _datalog_period           The rate at which data is reported for logging
// SetADC_Channel            Defines the channels input pin and calibration constants
//
//
// Calibration values
//-------------------
// Many calibration values are used in this sketch: 
//
// ADCCal                    This sets up the ADC reference voltage
// voltageCal                This is the principal calibration for the ac adapter.
// currentCal                A per-channel amplitude calibration for each current transformer.
// phaseCal                  A per-channel calibration for the phase error correction


// With most hardware, the default values are likely to work fine without 
// need for change.  A compact explanation of each of these values now follows:

// Voltage calibration constant. This is the mains voltage that would give 1 V 
//  at the ADC input:

// AC-AC Voltage adapter is designed to step down the voltage from 240V to 9V
// but the AC Voltage adapter is running open circuit and so output voltage is
// likely to be about 20% higher than 9V, actually 11.6 V for the UK Ideal adapter
//  (from the data sheet). 
// Open circuit step down = 240 / 11.6 = 20.69

// The output voltage is then stepped down further with the voltage divider which has 
// values Rb = 10k, Rt = 120k which will reduce the voltage by 13 times.

// The combined step down is therefore 20.69 x 13 = 268.97 which is the 
// theoretical calibration constant. The actual constant for a given
// unit and ac adapter is likely to be different by a few percent.
// Other adapters may be different by more.

// Current calibration constant. This is the mains current that would give 1 V
// at the ADC input:
// Current calibration constant channels 1 - 3 = 100 A / 50 mA / 22 Ohms burden resistor = 90.9
// (The default CT sensor is 100 A : 50 mA)
//  for channel 4 is 100 A / 50 mA  / 120R burden resistor = 16.67
//  The actual constant for a given unit and CT is likely to be different by a few percent.

// phaseCal is used to alter the phase of the voltage waveform relative to the
// current waveform.  The algorithm interpolates between the most recent pair
// of voltage samples according to the value of phaseCal. 
//
// The value of phaseCal entered is difference between the phase lead of the voltage transformer and
// the phase lead of the current transformer, in degrees (changes of less than 0.1 deg are
// unlikely to make a detectable difference).



/**************************************************************************************************
*
*   General variables 
*
*
***************************************************************************************************/


// --------------  general global variables -----------------
// Some of these variables are used in multiple blocks so cannot be static.
// For integer maths, many variables need to be 'long' or in extreme cases 'int64_t'

double currentCal[max_no_of_channels] = {90.91, 90.91, 90.91, 16.67, 90.91};
double  phaseCal_CT[max_no_of_channels] ={4.2, 4.2, 4.2, 1.0, 4.2}; 

double voltageCal = 268.97;

unsigned int ADC_Counts = 1 << ADCBits;

bool stop = false;
volatile bool firstcycle = true;
    
unsigned int samplesDuringThisCycle;
bool acPresent = false;                             // TRUE when ac voltage input is detected.
unsigned int acDetectedThreshold = ADC_Counts >> 5; // ac voltage detection threshold, ~10% of nominal voltage (given large amount of ripple)
double assumedVrms = 240.0;

unsigned int datalogPeriodInMainsCycles;
unsigned long ADCsamples_per_datalog_period;

// accumulators & counters for use by the ISR
long     cumV_deltas;                               // <--- for offset removal (V)
int64_t  sumPA_CT[max_no_of_channels];              // 'partial' power for real power calculation
int64_t  sumPB_CT[max_no_of_channels];              // 'partial' power for real power calculation
uint64_t sumIsquared_CT[max_no_of_channels];
long     cumI_deltas_CT[max_no_of_channels];        // <--- for offset removal (I)
uint64_t sum_Vsquared;                              // for Vrms datalogging   
long     sampleSetsDuringThisDatalogPeriod;   

// Copies of ISR data for use by the main code
// These are filled by the ADC helper routine at the end of the datalogging period

volatile int64_t  copyOf_sumPA_CT[max_no_of_channels]; 
volatile int64_t  copyOf_sumPB_CT[max_no_of_channels]; 
volatile uint64_t copyOf_sumIsquared_CT[max_no_of_channels]; 
volatile uint64_t copyOf_sum_Vsquared;
volatile long     copyOf_sampleSetsDuringThisDatalogPeriod;
volatile int64_t  copyOf_cumI_deltas[max_no_of_channels];
volatile int64_t  copyOf_cumV_deltas;

// For mechanisms to check the integrity of this code structure
#ifdef INTEGRITY
int sampleSetsDuringThisMainsCycle;    
int lowestNoOfSampleSetsPerMainsCycle;
volatile int copyOf_lowestNoOfSampleSetsPerMainsCycle;
#endif

enum polarities {NEGATIVE, POSITIVE};
// For an enhanced polarity detection mechanism, which includes a persistence check
#define POLARITY_CHECK_MAXCOUNT 3 // 1
polarities polarityUnconfirmed;   
polarities polarityConfirmed;                       // for improved zero-crossing detection
polarities polarityConfirmedOfLastSampleV;          // for zero-crossing detection

float residualEnergy_CT[max_no_of_channels];
double x[max_no_of_channels], y[max_no_of_channels]; // coefficients for real power interpolation


// Temperature measurement
//
// Hardware Configuration
byte W1Pin = 5;                                     // 1-Wire pin for temperature = 5 for emonTx V3, 4 for emonTx V2 & emonTx Shield
char DS18B20_PWR = -1;                              // Power pin for DS18B20 temperature sensors. Default -1 - power off

// Global variables used only inside the library
OneWire oneWire(W1Pin);
bool temperatureEnabled = false;
byte numSensors = 0;
byte temperatureResolution = TEMPRES_11;
byte temperatureMaxCount = 1;
DeviceAddress *temperatureSensors = NULL;
bool keepAddresses = false;
int *temperatures = NULL;
unsigned int temperatureConversionDelayTime; 
unsigned long temperatureConversionDelaySamples;

volatile bool startConvertTemperatures = false;
volatile bool convertingTemperaturesNoAC = false;            // Only used when not using mains for timing.

/**************************************************************************************************
*
*   APPLICATION INTERFACE - Getters & Setters
*
*
***************************************************************************************************/

void EmonLibCM_SetADC_VChannel(byte ADC_Input, double _amplitudeCal)
{
    ADC_Sequence[0] = ADC_Input; 
    voltageCal = _amplitudeCal;
}

void EmonLibCM_SetADC_IChannel(byte ADC_Input, double _amplitudeCal, double _phaseCal)
{
    currentCal[no_of_Iinputs] = _amplitudeCal;
    phaseCal_CT[no_of_Iinputs] = _phaseCal;
    ChannelInUse[no_of_Iinputs] = true;            
    lChannel[ADC_Input] = no_of_Iinputs;
    ADC_Sequence[++no_of_Iinputs] = ADC_Input; 
}

void EmonLibCM_ReCalibrate_VChannel(double _amplitudeCal)
{
    voltageCal = _amplitudeCal * Vref / ADC_Counts;
}

void EmonLibCM_ReCalibrate_IChannel(byte ADC_Input, double _amplitudeCal, double _phaseCal)
{
    byte lChannel = EmonLibCM_getLogicalChannel(ADC_Input);
    currentCal[lChannel] = _amplitudeCal * Vref / ADC_Counts;  
    phaseCal_CT[lChannel] = _phaseCal;
    calcPhaseShift(lChannel);
}

void EmonLibCM_cycles_per_second(unsigned int _cycles_per_second)
{
    cycles_per_second = _cycles_per_second;
    datalogPeriodInMainsCycles = datalog_period_in_seconds * cycles_per_second;  
    calcTemperatureLead();
    for (byte i = 0; i<no_of_channels; i++)
        calcPhaseShift(i);
}

void EmonLibCM_min_startup_cycles(unsigned int _min_startup_cycles)
{
    min_startup_cycles = _min_startup_cycles;
}

void EmonLibCM_datalog_period(float _datalog_period_in_seconds)
{
    if (datalog_period_in_seconds < 0.1)
        datalog_period_in_seconds = 0.1;
    datalog_period_in_seconds = _datalog_period_in_seconds;
    datalogPeriodInMainsCycles = datalog_period_in_seconds * cycles_per_second;  
    ADCsamples_per_datalog_period = datalog_period_in_seconds * MICROSPERSEC / ADCDuration;    
    // Set lead time to start temperature conversion
    calcTemperatureLead();
}

void EmonLibCM_setADC(int _ADCBits,  int _ADCDuration)
{
    ADCBits = _ADCBits;
    ADCDuration = _ADCDuration;
}

void EmonLibCM_setADC_VRef(byte _ADCRef)
{
    ADCRef = _ADCRef << 6;
}

void EmonLibCM_setPulseEnable(bool _enable)
{
    pulses[0].PulseEnabled = _enable;
    pulses[0].PulseChange = true;
}

void EmonLibCM_setPulseEnable(byte channel, bool _enable)
{
    pulses[channel].PulseEnabled = _enable;
    pulses[channel].PulseChange = true;
}

void EmonLibCM_setPulsePin(int _pin)
{
    pulses[0].PulsePin = _pin;
    pulses[0].PulseInterrupt = digitalPinToInterrupt(_pin);
}

void EmonLibCM_setPulsePin(byte channel, int _pin, int _interrupt)
{
    pulses[channel].PulsePin = _pin;
    pulses[channel].PulseInterrupt = _interrupt;
}

void EmonLibCM_setPulsePin(byte channel, int _pin)
{
    if (channel != 0 || channel != 1)  // Attempt to deal with incompatibility with prior versions
    {
      _pin = channel;
      channel = 0;
    }
    pulses[channel].PulsePin = _pin;
    pulses[channel].PulseInterrupt = digitalPinToInterrupt(_pin);
}
void EmonLibCM_setPulseMinPeriod(int _period)
{
    pulses[0].PulseMinPeriod = _period;
}

void EmonLibCM_setPulseMinPeriod(byte channel, int _period)
{
    pulses[channel].PulseMinPeriod = _period;
}

void EmonLibCM_setPulseCount(long _pulseCount)
{
    pulses[0].pulseCount = _pulseCount;                 
}

void EmonLibCM_setPulseCount(byte channel, long _pulseCount)
{
    pulses[channel].pulseCount = _pulseCount;                
}

void EmonLibCM_setAssumedVrms(double _assumedVrms)
{
    assumedVrms = _assumedVrms;
}

void EmonLibCM_setWattHour(byte channel, long _wh)
{
    wh_CT[channel] = _wh;
}

void EmonLibCM_ADCCal(double _Vref)
{
    Vref = _Vref;
}   


bool EmonLibCM_acPresent(void)
{
    return(acPresent);
}

int EmonLibCM_getRealPower(int channel)
{
    return realPower_CT[channel];
}

int EmonLibCM_getApparentPower(int channel)
{
    return apparentPower_CT[channel];
}

double EmonLibCM_getPF(int channel)
{
    return pf[channel];
}

double EmonLibCM_getIrms(int channel)
{
    return Irms_CT[channel];
}

double EmonLibCM_getVrms(void)
{
    return Vrms;
}

double EmonLibCM_getAssumedVrms(void)
{
    return assumedVrms;
}

double EmonLibCM_getDatalog_period(void)
{
    return datalog_period_in_seconds;
}

double EmonLibCM_getLineFrequency(void)
{
    if (acPresent)
        return line_frequency;
    else
        return 0;
}

long EmonLibCM_getWattHour(int channel)
{
    return wh_CT[channel];
}

unsigned long EmonLibCM_getPulseCount(void)
{
    return pulses[0].pulseCount;
}

unsigned long EmonLibCM_getPulseCount(byte channel)
{
    return pulses[channel].pulseCount;
}

int EmonLibCM_getLogicalChannel(byte ADC_Input)
{
    // Look up logical channel associated with physical pin 
    //  N.B. Returns 255 for an unused input
    return lChannel[ADC_Input];
}


#ifdef INTEGRITY
int EmonLibCM_minSampleSetsDuringThisMainsCycle(void)    
{
    return copyOf_lowestNoOfSampleSetsPerMainsCycle;
    // The answer should be 192 (50 Hz) or 160 (60 Hz) divided by
    // 2 for 1 CT in use, 3 for 2 CTs in use, etc.
    // Returns 999 if no mains is detected.
}    
#endif



void EmonLibCM_Init(void)
{   
    // Set number of channels to the number defined, else use the defaults
    if (no_of_Iinputs)
    { 
        no_of_channels = no_of_Iinputs;
        for (byte i = no_of_Iinputs+1; i < max_no_of_channels; i++)
            ChannelInUse[i] = false;
    }
 
    // Set up voltage calibration to take account of ADC width etc
    voltageCal = voltageCal * Vref / ADC_Counts;
    
    // Likewise each current channel
    for (int i=0; i<no_of_channels; i++)
    {
        currentCal[i] = currentCal[i] * Vref / ADC_Counts;  
        calcPhaseShift(i);
        residualEnergy_CT[i] = 0;
    }

    EmonLibCM_Start();
    
    datalogPeriodInMainsCycles = datalog_period_in_seconds * cycles_per_second;  
    datalogEventPending = false;
    ADCsamples_per_datalog_period = datalog_period_in_seconds * MICROSPERSEC / ADCDuration;
        // nominally a truncation error of 0.16% at 1s, or 0.004% at 10 s by having this as an integer - insignificant 
#ifdef  SAMPPIN
    pinMode(SAMPPIN, OUTPUT);
    digitalWrite(SAMPPIN, LOW);
#endif

    for (byte channel = 0; channel < PULSEINPUTS; channel++)
    {

        if (pulses[channel].PulseEnabled)
        {
            pinMode(pulses[channel].PulsePin, INPUT_PULLUP);               // Set interrupt pulse counting pin as input & attach interrupt
            if (channel == 0)
              attachInterrupt(pulses[channel].PulseInterrupt, onPulse0, RISING);
            if (channel == 1)
              attachInterrupt(pulses[channel].PulseInterrupt, onPulse1, RISING);
        }
#ifdef INTPINS        
  Serial.print("Ch: ");Serial.println(channel);
  Serial.print(" en: ");Serial.println(pulses[channel].PulseEnabled);
  Serial.print(" pin: ");Serial.println(pulses[channel].PulsePin);
  Serial.print(" int: ");Serial.println(pulses[channel].PulseInterrupt);
  Serial.print(" pin3, int: ");Serial.println(digitalPinToInterrupt(3));
  Serial.print(" pin2, int: ");Serial.println(digitalPinToInterrupt(2));
#endif
    }

     
}

/**************************************************************************************************
*
*   START
*
*
***************************************************************************************************/


void EmonLibCM_Start(void)
{
  
    pulses[0].pulseISR = onPulse0;
    pulses[1].pulseISR = onPulse1;
    
    firstcycle = true;
    missing_VoltageSamples = 0;
    
    // Set up the ADC to be free-running 
    // 
    // BIT:    7,    6,    5,    4,    3,    2,     1,     0
    // ADCSRA: ADEN, ADSC, ADFR, ADIF, ADIE, ADPS2, ADPS1, ADPS0
    //
    // ADEN: ADC Enable
    // ADSC: ADC Start Conversion
    // ADFR: ADC Free Running Select, or ADATE (ADC Auto Trigger Enable)
    // ADIF: ADC Interrupt Flag
    // ADIE: ADC Interrupt Enable
    // ADPS2, ADPS1, ADPS0: ADC Prescaler Select Bits (CLOCK FREQUENCY)
    //
    // The default value of ADCSRA before we change it with the following is 135
    // ADCSRA: ADEN, ADSC, ADFR, ADIF, ADIE, ADPS2, ADPS1, ADPS0
    //         128   64    32    16    8     4      2      1
    //         1     0     0     0     0     1      1      1
    // The ADC is enabled and the ADC clock is set to system clock / 128
    //
    // The following sets ADCSRA to a value of 239
    //         1     1     1     0     1     1      1      1
     
    ADCSRA  = (1<<ADPS0)+(1<<ADPS1)+(1<<ADPS2);  // Set the ADC's clock to system clock / 128
    ADCSRA |= (1 << ADEN);                       // Enable the ADC 

    ADCSRA |= (1<<ADATE);  // set the Auto Trigger Enable bit in the ADCSRA register.  Because 
                           // bits ADTS0-2 have not been set (i.e. they are all zero), the 
                           // ADC's trigger source is set to "free running mode".
                         
    ADCSRA |=(1<<ADIE);    // set the ADC interrupt enable bit. When this bit is written 
                           // to one and the I-bit in SREG is set, the 
                           // ADC Conversion Complete Interrupt is activated. 

    ADCSRA |= (1<<ADSC);   // start ADC manually first time 
    sei();                 // Enable Global Interrupts
    
    
}

void EmonLibCM_StopADC(void)
{
    // This stop function returns the ADC to default state
    ADCSRA  = (1<<ADPS0)+(1<<ADPS1)+(1<<ADPS2);  // Set the ADC's clock to system clock / 128
    ADCSRA |= (1<<ADEN);                         // Enable the ADC
    ADCSRA |= (0<<ADATE);
    ADCSRA |= (0<<ADIE);
    ADCSRA |= (0<<ADSC);
    
    stop = false;
}


/**************************************************************************************************
*
*   Retrieve and apply final processing of data ready for reporting
*
*
***************************************************************************************************/

void EmonLibCM_get_readings()
{
    // Use the 'volatile' variables passed from the ISR.

    double frequencyDeviation;
    
    cli();

    for (int i=0; i<no_of_channels; i++) 
    {
      if (!ChannelInUse[i])
      {
          copyOf_sumPA_CT[i] = 0;
          copyOf_sumPB_CT[i] = 0;
          copyOf_sumIsquared_CT[i] = 0;
          copyOf_cumI_deltas[i] = 0;
      }
    }           

    for (byte channel = 0; channel < PULSEINPUTS; channel++)
    {
        if (pulses[channel].PulseChange)
        {
          if (pulses[channel].PulseEnabled)
          {
              pinMode(pulses[channel].PulsePin, INPUT_PULLUP);         // Set interrupt pulse counting pin as input & attach interrupt
              if (channel == 0)
                attachInterrupt(pulses[channel].PulseInterrupt, onPulse0, RISING);
              if (channel == 1)
                attachInterrupt(pulses[channel].PulseInterrupt, onPulse1, RISING);              
          }
          else 
          {
              detachInterrupt(pulses[channel].PulseInterrupt);         // Detach pulse counting interrupt
              pulses[channel].PulseChange = false; 
          }
        }
        if (pulses[channel].pulseIncrement)                        // if the ISR has counted some pulses, update the total count
        {
            pulses[channel].pulseCount += pulses[channel].pulseIncrement;
            pulses[channel].pulseIncrement = 0;
        }
    }
    
    sei();

    
    // Calculate the final values, scaling for the number of samples and applying calibration coefficients.
    // The final values are deposited in global variables for extraction by the 'getter' functions.
    
    // The rms of a signal plus an offset is  sqrt( signal^2 + offset^2). 
    // Vrms still contains the fine voltage offset. Correct this by subtracting the "Offset V^2" before the sq. root.
    // Real Power is calculated by interpolating between the 'partial power' values, applying "trigonometric" coefficients to
    //  preserve the amplitude of the interpolated value.
    Vrms = sqrt(((double)copyOf_sum_Vsquared / copyOf_sampleSetsDuringThisDatalogPeriod)
                - ((double)copyOf_cumV_deltas * copyOf_cumV_deltas / copyOf_sampleSetsDuringThisDatalogPeriod / copyOf_sampleSetsDuringThisDatalogPeriod)); 
    Vrms *= voltageCal; 
    
    frequencyDeviation = (double)ADCsamples_per_datalog_period / (copyOf_sampleSetsDuringThisDatalogPeriod * (no_of_channels + 1)); // nominal value / actual value
    line_frequency = cycles_per_second * frequencyDeviation;

    for (int i=0; i<no_of_channels; i++)    // Current channels
    {
        double powerNow;
        double energyNow;
        double VA;
        int wattHoursRecent;
        double sumRealPower;

        
        // Apply combined phase & timing correction
        sumRealPower = (copyOf_sumPA_CT[i] * x[i] + copyOf_sumPB_CT[i] * y[i]); 
                
        // sumRealPower still contains the fine offsets of both V & I. Correct this by subtracting the "Offset Power": cumV_deltas * cumI_deltas
        powerNow = (sumRealPower / copyOf_sampleSetsDuringThisDatalogPeriod - (double)copyOf_cumV_deltas * copyOf_cumI_deltas[i] 
                   / copyOf_sampleSetsDuringThisDatalogPeriod / copyOf_sampleSetsDuringThisDatalogPeriod) * voltageCal * currentCal[i];        
      
        //  root of mean squares, removing fine offset
        //  The rms of a signal plus an offset is  sqrt( signal^2 + offset^2). 
        //  Here (signal+offset)^2 = copyOf_sumIsquared_CT / no of samples
        //       offset = cumI_deltas / no of samples
        Irms_CT[i] = sqrt(((double)copyOf_sumIsquared_CT[i] / copyOf_sampleSetsDuringThisDatalogPeriod) - ((double)copyOf_cumI_deltas[i] * copyOf_cumI_deltas[i] / copyOf_sampleSetsDuringThisDatalogPeriod / copyOf_sampleSetsDuringThisDatalogPeriod));
        
        Irms_CT[i] *= currentCal[i];    
    
        if (acPresent)
        {
          VA = Irms_CT[i] * Vrms;
          
          pf[i] = powerNow / VA;
          if (pf[i] > 1.05 || pf[i] < -1.05 || isnan(pf[i]))
            pf[i] = 0.0;

          realPower_CT[i] = powerNow + 0.5;                                                       // rounded to nearest Watt
          apparentPower_CT[i]   = VA + 0.5;                                                       // rounded to nearest VA
          energyNow = (powerNow * datalog_period_in_seconds / frequencyDeviation)                 // correct for mains time != clock time
            + residualEnergy_CT[i];                                                               // fp for accuracy
        }
        else
        {
          VA = Irms_CT[i] * assumedVrms;
          
          pf[i] = 0.0;

          realPower_CT[i] = VA + 0.5;                                                     // rounded to nearest Watt
          apparentPower_CT[i]   = VA + 0.5;                                                     // rounded to nearest VA
          energyNow = (VA * datalog_period_in_seconds / frequencyDeviation)                 // correct for mains time != clock time
            + residualEnergy_CT[i];                                                               // fp for accuracy
        }
        wattHoursRecent = energyNow / 3600;                                                     // integer assignment to extract whole Wh
        wh_CT[i]+= wattHoursRecent;                                                             // accumulated WattHours since start-up
        residualEnergy_CT[i] = energyNow - (wattHoursRecent * 3600.0);                          // fp for accuracy
    }
   
    //  Retrieve the temperatures, which should be stored inside each sensor
    if (temperatureEnabled)
    {
        retrieveTemperatures();
    }
   
}

bool EmonLibCM_Ready()
{
    if (startConvertTemperatures)
    {
        startConvertTemperatures = false;
        convertTemperatures();
    }
    
    if (datalogEventPending) 
    {
        datalogEventPending = false;        
        EmonLibCM_get_readings();
        return true;
    }
    return false;
}


void EmonLibCM_confirmPolarity()
{
    /* This routine prevents a zero-crossing point from being declared until 
    * a certain number of consecutive samples in the 'other' half of the 
    * waveform have been encountered.  It forms part of the ISR.
    */ 
    static byte count = 0;
    
    if (polarityUnconfirmed != polarityConfirmedOfLastSampleV) 
    { 
        count++; 
    } 
    else 
    {
        count = 0; 
    }

    if (count >= POLARITY_CHECK_MAXCOUNT) {
        count = 0;
        polarityConfirmed = polarityUnconfirmed;
    }
}

void calcPhaseShift(byte lChannel)
{
    /* Calculate the 'X' & 'Y' coefficients of phase shift for the c.t.
    * phaseCal value supplied is the difference between VT lead and CT lead in degrees
    * Add the delay due to the time taken by the ADC to convert one sample (ADCDuration),
    * knowing the position of the current sample with respect to 
    * the voltage, then convert to radians.
    * x & y are the constants used in the power interpolation. (Sanity check: x + y ≈ 1)
    */
     
    const double two_pi = 6.2831853;
    double sampleRate = ADCDuration * (no_of_channels + 1) * two_pi * cycles_per_second / MICROSPERSEC; // in radians
    double phase_shift = (phaseCal_CT[lChannel] / 360.0 + (lChannel+1) * ADCDuration 
                           * (double)cycles_per_second/MICROSPERSEC) * two_pi;                // Total phase shift in radians
                                                                                              // (lChannel+1) was ADC_Sequence[lChannel+1]
    y[lChannel] = sin(phase_shift) / sin(sampleRate);        
    x[lChannel] = cos(phase_shift) - y[lChannel] * cos(sampleRate);
}


void calcTemperatureLead(void)
{
    /* Set lead time to start temperature conversion
    * The temparature sensors are instructed to 'convert' the temperature just in time for the result
    * to be available to be retrieved and reported along with the other data.
    * The lead time is the number of cycles (or in the absence of ac, no. of samples) to allow after 
    * datalogEventPending has been set to true, so that temperature conversion will complete just before 
    * the next datalog event. Adjust the resolution if necessary so that conversion within one 
    * datalogging period is possible.
    */
    
    int conversionLeadTime = (CONVERSION_LEAD_TIME >> (3 - ((temperatureResolution & 0x70) >> 5)));  
        // Should give 95 - 760 ms lead time, now convert to cycles (for a.c. present) or samples (for a.c. not present).
    temperatureConversionDelayTime = datalogPeriodInMainsCycles - (long)conversionLeadTime * cycles_per_second / 1000 - 1; 
        // '-1' to counter the effect of integer truncation, and make sure there is some spare time
    temperatureConversionDelaySamples = ((unsigned long)(datalog_period_in_seconds * 1000.0) 
        - (unsigned long)conversionLeadTime - 5) * 1000 / ADCDuration;
        // '- 5' extra 5 ms to make sure there is some spare time
}


/**************************************************************************************************
*
*   ADC Interrupt Handling
*
*
***************************************************************************************************/


void EmonLibCM_allGeneralProcessing_withinISR()
{
  /* This routine deals with activities that are only required at specific points
   * within each mains cycle.  It forms part of the ISR.
   */ 
  if (stop) 
      EmonLibCM_StopADC();
  static unsigned int cycleCountForDatalogging = 0;
  // a simple routine for checking the performance of this new ISR structure

  if (acPresent)
  {
      if (polarityConfirmed == POSITIVE) 
      { 
          if (polarityConfirmedOfLastSampleV != POSITIVE)
          {
            /* Instantaneous power contributions are summed in accumulators during each 
             * datalogging period.  At the end of each period, copies are made of their 
             * content for use by the main code.  The accumulators, and any associated
             * counters are then reset for use during the next period.
             */       
            cycleCountForDatalogging++;
            #ifdef INTEGRITY
                if (sampleSetsDuringThisMainsCycle < lowestNoOfSampleSetsPerMainsCycle)
                {
                    lowestNoOfSampleSetsPerMainsCycle = sampleSetsDuringThisMainsCycle;
                }
                sampleSetsDuringThisMainsCycle = 0;   
            #endif            
           
            // Used in stop start operation, discards the first partial cycle
            if (firstcycle==true && cycleCountForDatalogging >= min_startup_cycles)
            {
                firstcycle = false;
                cycleCountForDatalogging = 0;
                for (int i=0; i<no_of_channels; i++) 
                { 
                  sumPA_CT[i] = 0;
                  sumPB_CT[i] = 0;
                  sumIsquared_CT[i] = 0;
                  cumI_deltas_CT[i] = 0;
                }
                sum_Vsquared = 0;
                cumV_deltas = 0;
    #ifdef INTEGRITY
                lowestNoOfSampleSetsPerMainsCycle = 999;
    #endif          
                sampleSetsDuringThisDatalogPeriod = 0;
            }
          
          // Start temperature conversion
            if (cycleCountForDatalogging == temperatureConversionDelayTime  && firstcycle==false)
            {
                // Only do it on this one cycle
                startConvertTemperatures = true;
            }
            if (cycleCountForDatalogging >= datalogPeriodInMainsCycles && firstcycle==false) 
            {
              cycleCountForDatalogging = 0;
              for (int i=0; i<no_of_channels; i++) 
              {
                copyOf_sumPA_CT[i] = sumPA_CT[i]; 
                copyOf_sumPB_CT[i] = sumPB_CT[i]; 
                sumPA_CT[i] = 0;
                sumPB_CT[i] = 0;
                copyOf_sumIsquared_CT[i] = sumIsquared_CT[i]; 
                sumIsquared_CT[i] = 0;
                copyOf_cumI_deltas[i] = cumI_deltas_CT[i];
                cumI_deltas_CT[i] = 0;
              }
              copyOf_cumV_deltas = cumV_deltas;
              copyOf_sum_Vsquared = sum_Vsquared;
              sum_Vsquared = 0;
              cumV_deltas = 0;
              copyOf_sampleSetsDuringThisDatalogPeriod = sampleSetsDuringThisDatalogPeriod;
              sampleSetsDuringThisDatalogPeriod = 0;
    #ifdef INTEGRITY
              copyOf_lowestNoOfSampleSetsPerMainsCycle = lowestNoOfSampleSetsPerMainsCycle; // (for diags only)
              lowestNoOfSampleSetsPerMainsCycle = 999;
    #endif
              
              datalogEventPending = true;           
            }
          } // end of processing that is specific to the first Vsample in each +ve half cycle   
      } // end of processing that is specific to samples where the voltage is positive
      
      else // the polarity of this sample is negative
      {     
        if (polarityConfirmedOfLastSampleV != NEGATIVE)
        {
          // This is the start of a new -ve half cycle (just after the zero-crossing point)
          //
          samplesDuringThisCycle = 0;    
          // check_RF_LED_status();       
        } // end of processing that is specific to the first Vsample in each -ve half cycle
      } // end of processing that is specific to samples where the voltage is positive
  }
  else
  {    
    // In the case where the voltage signal is missing this part counts ADC samples up to the
    // duration of the datalog period, at which point it will make the readings available.
    // The reporting interval is now dependent on the processor's internal clock

    // Start temperature conversion
    if (missing_VoltageSamples > temperatureConversionDelaySamples && convertingTemperaturesNoAC == false)
    {
        // Only do it once per report
        startConvertTemperatures = true;
        convertingTemperaturesNoAC = true;
    }
    
    if (missing_VoltageSamples > ADCsamples_per_datalog_period) 
    {
        missing_VoltageSamples = 0;  // reset the missing samples count here.

        firstcycle = true;    // firstcycle reset to true so that next reading
                              // with voltage signal starts from the right place
        #ifdef INTEGRITY
            lowestNoOfSampleSetsPerMainsCycle = 999;
        #endif          
                          
        cycleCountForDatalogging = 0;    
        for (int i=0; i<no_of_channels; i++) 
        {
            copyOf_sumPA_CT[i] = 0;
            copyOf_sumPB_CT[i] = 0;
            sumPA_CT[i] = 0;
            sumPB_CT[i] = 0;
            copyOf_sumIsquared_CT[i] = sumIsquared_CT[i]; 
            sumIsquared_CT[i] = 0;
            copyOf_cumI_deltas[i] = cumI_deltas_CT[i];
            cumI_deltas_CT[i] = 0;
        }
        copyOf_sum_Vsquared = sum_Vsquared;
        sum_Vsquared = 0;
        copyOf_cumV_deltas = cumV_deltas;
        cumV_deltas = 0;
        copyOf_sampleSetsDuringThisDatalogPeriod = sampleSetsDuringThisDatalogPeriod;
        sampleSetsDuringThisDatalogPeriod = 0;
#ifdef INTEGRITY
        copyOf_lowestNoOfSampleSetsPerMainsCycle = lowestNoOfSampleSetsPerMainsCycle; // (for diags only)
        // lowestNoOfSampleSetsPerMainsCycle = 999;
#endif        
        datalogEventPending = true;

        // Stops the sampling at the end of the cycle if EmonLibCM_Stop() has been called
        // if (stop) EmonLibCM_StopADC();                
    }
  }
 
}
// end of EmonLibCM_allGeneralProcessing_withinISR()

// This Interrupt Service Routine is for use when the ADC is in the free-running mode.
// It is executed whenever an ADC conversion has finished, approx every 104 us.  In 
// free-running mode, the ADC has already started its next conversion by the time that
// the ISR is executed.  The ISR therefore needs to "look ahead". 
//   At the end of conversion Type N, conversion Type N+1 will start automatically.  The ISR 
// which runs at this point therefore needs to capture the results of conversion Type N, 
// and set up the conditions for conversion Type N+2, and so on.  
//   Activities that are required for every new sample are performed here.  Activities
// that are only required at certain stages of the voltage waveform are performed within
// the helper function, EmonLibCM_allGeneralProcessing_withinISR().
//   A second helper function, confirmPolarity() is used to apply a persistence criterion
// when the polarity status of each voltage sample is checked. 
// 
void EmonLibCM_interrupt()  
{                                         
  int rawSample;
  static unsigned char sample_index = 0;
  unsigned char next = 0;
  static int sampleV_minusDC;
  static int lastSampleV_minusDC; 
  int sampleI_minusDC;
  
  static unsigned int acSense = 0;
  
#ifdef SAMPPIN
    digitalWrite(SAMPPIN,HIGH);
#endif
  
  rawSample = ADC;
  next = sample_index + 2;
  if (next>no_of_channels)                 // no_of_channels = count of Current channels in use. Voltage channel (0) is always read, so total is no_of_channels + 1
      next -= no_of_channels+1;
  
  ADMUX = ADCRef + ADC_Sequence[next];     // set up the next-but-one conversion
#ifdef SAMPPIN
    digitalWrite(SAMPPIN,LOW);
#endif
  // Count ADC samples for timing when voltage is unavailable
  missing_VoltageSamples++;

  
  if (sample_index==0)                                               // ADC_Sample 0 is always the voltage channel.
  {
#ifdef SAMPPIN
    digitalWrite(SAMPPIN,HIGH);
#endif
      // Removing the d.c. offset - new method:
      // Rather than use a filter, which takes time to settle and will always contain a residual ripple, and which can lock
      // up under start-up conditions, it is possible to remove the effect of the offset at the final stage of measurement.
      // First take off the theoretical (constant) offset to reduce the size of the numbers (as Robin's original method).
      // Then accumulate the sum of the resulting values so as to be able at the end of the measurement period to 
      // recalculate the true rms based on the rms with the offset and the average remaining offset. The remaining offset 
      // should be only a few counts.
      //
      lastSampleV_minusDC = sampleV_minusDC;                         // required for phaseCal algorithm
      sampleV_minusDC = rawSample - (ADC_Counts >> 1);               // remove nominal offset (a small offset will remain)
      // Detect the ac input voltage. This is a 'rough&ready" rectifier/filter. It only needs to be good enough to detect
      //  sufficient voltage to provide assurance that the crossing detector will function properly
      acSense -= acSense >> 2;
      acSense += sampleV_minusDC > 0 ? sampleV_minusDC : -sampleV_minusDC;
      acPresent = acSense > acDetectedThreshold;
      //
      // deal with activities that are only needed at certain stages of each  
      // voltage cycle.

      if (sampleV_minusDC > 0) 
      { 
        polarityUnconfirmed = POSITIVE; 
      }
      else 
      { 
       polarityUnconfirmed = NEGATIVE; 
      }
      EmonLibCM_confirmPolarity();
      EmonLibCM_allGeneralProcessing_withinISR();
      //
      // for real power calculations
#ifdef INTEGRITY
      sampleSetsDuringThisMainsCycle++; 
#endif
      sampleSetsDuringThisDatalogPeriod++;      
      samplesDuringThisCycle++;
      //
      // for the Vrms calculation 
      sum_Vsquared += ((long)sampleV_minusDC * sampleV_minusDC);     // cumulative V^2 (V_ADC x V_ADC)
      //
      // store items for later use
      cumV_deltas += sampleV_minusDC;                                // for use with offset removal

      polarityConfirmedOfLastSampleV = polarityConfirmed;            // for identification of half cycle boundaries
#ifdef SAMPPIN
        digitalWrite(SAMPPIN,LOW);
#endif
      
  }
  
  if (sample_index>=1 && sample_index <= no_of_channels) 
  {
      // Now do much the same for each current sample as it is read.
      // N.B. The Current channels are zero-based but offset by 1 from the ADC sample_index.
      //  That means Current Channel 0 is read from ADC Sample 1. 
      //   ADC_Sample 0 is always the voltage channel, handled in the section above.
      //   ADC_Sample 1 is always a current but not necessarily CT1.
      // Save the current sample for one sample set, so that the calculation normally uses voltage samples
      //   from each side of the current sample for interpolation in the phase shift algorithm.
    
#ifdef SAMPPIN
    digitalWrite(SAMPPIN,HIGH);
#endif

                                          
      static int lastRawSample[max_no_of_channels];  
      if (rawSample > 5)                                                                 // skip processing this sample if input is grounded
      {
        ChannelInUse[sample_index-1] = true;
       
        // Offset removal for current is the same as for the voltage.
      
        lastRawSample[sample_index-1] -= (ADC_Counts >> 1);                              // remove nominal offset (a small offset will remain)
       
        sampleI_minusDC = lastRawSample[sample_index-1];
              
        // calculate the "partial real powers" in this sample pair and add to the accumulated sums - fine d.c. offsets are still present
        sumPA_CT[sample_index-1] += (long)sampleI_minusDC * lastSampleV_minusDC;         // cumulative power A
        sumPB_CT[sample_index-1] += (long)sampleI_minusDC * sampleV_minusDC;             // cumulative power B
          
        // for Irms calculation 
        sumIsquared_CT[sample_index-1] += (long)sampleI_minusDC * sampleI_minusDC;       // this has the fine d.c. offset still present
        cumI_deltas_CT[sample_index-1] += sampleI_minusDC;                               // for use with offset removal

      }
      else
          ChannelInUse[sample_index-1] = false;
      
      lastRawSample[sample_index-1] = rawSample;                                         // Delay everything by 1 sample
#ifdef SAMPPIN      
      digitalWrite(SAMPPIN,LOW);
#endif
  }
  
  sample_index++; // advance the control flag
  if (sample_index>no_of_channels) 
      sample_index = 0;
}

/**************************************************************************************************
*
*   TEMPERATURES
*
*
***************************************************************************************************/


void EmonLibCM_setTemperatureDataPin(byte _dataPin)
{
    W1Pin = _dataPin;
}


void EmonLibCM_setTemperaturePowerPin(char _powerPin)
{
    DS18B20_PWR = _powerPin;
    if (DS18B20_PWR >= 0)
    {
        pinMode(DS18B20_PWR, OUTPUT);  
        digitalWrite(DS18B20_PWR, HIGH); 
    }
}


void EmonLibCM_setTemperatureResolution(byte _resolution)
{
    switch (_resolution)
    {
        case (9):  temperatureResolution = TEMPRES_9;
                   break;
        case (10): temperatureResolution = TEMPRES_10;
                   break;
        case (12): temperatureResolution = TEMPRES_12;
                   break;
        default:   temperatureResolution = TEMPRES_11;
                   break;
    }
}
    
    
void EmonLibCM_setTemperatureAddresses(DeviceAddress *addressArray)
{
    temperatureSensors = addressArray; 
    temperatureSensors[0][0] = 0x00;            // Used by "TemperatureEnable" to trigger search for sensors
}


void EmonLibCM_setTemperatureAddresses(DeviceAddress *addressArray, bool keep)
{
    temperatureSensors = addressArray; 
    keepAddresses = keep;
    if (!keep)
        temperatureSensors[0][0] = 0x00;        // Used by "TemperatureEnable" to trigger search for sensors
}


void EmonLibCM_setTemperatureArray(int *temperatureArray)
{
    temperatures = temperatureArray;
}


void EmonLibCM_setTemperatureMaxCount(int _maxCount)
{
    temperatureMaxCount = _maxCount;
}


void EmonLibCM_TemperatureEnable(bool _enable)
{
  //Setup and test for presence of DS18B20s, fill address array, set device resolution & write to EEPROM
    DeviceAddress deviceAddress;
  
    if (temperatureSensors == NULL || temperatures == NULL)
    {
        temperatureEnabled = false;                     // Could corrupt memory, try to limit damage
        numSensors = 0;
        return;                                         // & quit.
    }

    oneWire.begin(W1Pin);                               // In case W1Pin has changed.

    if (temperatureEnabled = _enable)
    {
        if (datalog_period_in_seconds < 1.0)            // Not enough time to convert between samples.
            temperatureResolution = TEMPRES_9;
        byte scratchpad[3];
        scratchpad[0] = 0;                              // low alarm
        scratchpad[1] = 0;                              // high alarm
        scratchpad[2] = temperatureResolution;          // resolution

        for(byte j=0; j<temperatureMaxCount; j++)
            temperatures[j] = UNUSED_TEMPERATURE;        // write 'Sensor never seen' marker to temperatures array
        oneWire.reset_search();
        numSensors = 0;
        while (oneWire.search(deviceAddress)) 
            if (deviceAddress[0] == DS18B20SIG)
                numSensors++;
        if (keepAddresses && temperatureSensors[0][0] != 0x00)
        {
            numSensors = temperatureMaxCount;
            for (numSensors = temperatureMaxCount; numSensors > 0; numSensors--)
            {
                if (temperatureSensors[numSensors-1][0] == DS18B20SIG)       // signature of a DS18B20, so a pre-existing sensor
                    break;
            }
        }
        else
        {
            if (numSensors > temperatureMaxCount)
                numSensors = temperatureMaxCount;
        }

        byte j=0;                                       // search for one wire devices and copy to device address array.
        
        if (temperatureSensors[0][0] != DS18B20SIG)     // not a signature of a DS18B20, so not a pre-existing array - search for sensors
            while ((j < numSensors) && (oneWire.search(temperatureSensors[j]))) 
                j++;
        oneWire.reset();                                // write resolution to scratchpad 
        oneWire.write(SKIP_ROM);
        oneWire.write(WRITE_SCRATCHPAD);
        for(int i=0; i<3; i++)
            oneWire.write(scratchpad[i]);
        oneWire.reset();                                // copy to EEPROM 
        oneWire.write(SKIP_ROM);
        oneWire.write(COPY_SCRATCHPAD, true);
        delay(20);                                      // required by DS18B20
    }
    else                                                // make sure power is turned off
    {
      if (DS18B20_PWR >= 0)
      {
          pinMode(DS18B20_PWR, OUTPUT);  
          digitalWrite(DS18B20_PWR, LOW); 
          pinMode(DS18B20_PWR, INPUT); 
      }
    }
    // Calculate number of cycles (or in the absence of ac, no. of samples) to allow after datalogEventPending has been set
    //  to true, so that temperature conversion will complete just before the next datalog event. Adjust the resolution if necessary
    //  so that conversion within one datalogging period is possible.
   
    calcTemperatureLead();    
}

void printTemperatureSensorAddresses(bool emonPi)
{
    if (emonPi)
      Serial.print(F("|"));
    Serial.print(F("Temperature Sensors found = "));
    Serial.print(numSensors);
    Serial.print(" of ");
    Serial.print(temperatureMaxCount);
    
    if (numSensors)
    {
        Serial.println(F(", with addresses..."));
        for (int j=0; j< numSensors; j++)
        {
            if (emonPi)
              Serial.print(F("|"));
            for (int i=0; i<8; i++)
            {
                if (temperatureSensors[j][i] < 0x10)
                  Serial.print(F("0"));
                Serial.print(temperatureSensors[j][i], 16);
                Serial.print(F(" "));
            }
            if (temperatureSensors[j][6] == 0x03)
              Serial.print(F("Sensor may not be reliable"));
            Serial.println();
            delay(5);
        }
        if (emonPi)
          Serial.print(F("|"));
    }
    Serial.println();
    if (emonPi)
      Serial.print(F("|"));
    Serial.print(F("Temperature measurement is"));
    Serial.print(temperatureEnabled?"":" NOT");
    Serial.println(F(" enabled."));
    if (emonPi)
      Serial.print(F("|"));
    Serial.println();
    delay(5);
        
}

void convertTemperatures(void)
{
    if (temperatureEnabled)
    {
        if (DS18B20_PWR >= 0)
        {
            pinMode(DS18B20_PWR, OUTPUT);  
            digitalWrite(DS18B20_PWR, HIGH); 
        }
        oneWire.reset();
        oneWire.write(SKIP_ROM);
        oneWire.write(CONVERT_TEMPERATURE, true); 
    }        // start conversion - all sensors    
}


void retrieveTemperatures(void)
{
    if (temperatureEnabled)
    {
        for (byte j=0; j < numSensors; j++)
        {
            byte buf[9];
            int result;
            if ((datalog_period_in_seconds < 0.2)                      // not enough time to get a reading
                || !oneWire.reset()
                || !temperatureSensors[j][0])                          // invalid address
            {
                temperatures[j] = BAD_TEMPERATURE;
                continue;
            }            
            else
            {
                oneWire.write(MATCH_ROM);
                for(int i=0; i<8; i++) 
                    oneWire.write(temperatureSensors[j][i]);
                oneWire.write(READ_SCRATCHPAD);
                for(int i=0; i<9; i++) 
                    buf[i] = oneWire.read();
            }

            if(oneWire.crc8(buf,8)==buf[8])
            {
                result = (buf[1]<<8)|buf[0];
                // result is temperature x16, multiply by 6.25 to convert to temperature x100
                result = (result*6)+(result>>2);
            }
            else result = BAD_TEMPERATURE;
            if (buf[4] == 0)
              result = BAD_TEMPERATURE;
            if (buf[6] ==  0x0C && result == 8500)  // not genuine 85 °C
              result = BAD_TEMPERATURE;
            if (result != BAD_TEMPERATURE && (result < -5500 || result > 12500))
                result = OUTOFRANGE_TEMPERATURE;
            temperatures[j] = result;
            delay(1);
        }
        for (byte j=numSensors; j < temperatureMaxCount; j++)
          temperatures[j] = UNUSED_TEMPERATURE;
        
        digitalWrite(DS18B20_PWR, LOW); 
        convertingTemperaturesNoAC = false;
    }
}


int EmonLibCM_getTemperatureSensorCount(void)
{
    if (temperatureEnabled)
        return(numSensors); 
    else
        return 0;
}

bool EmonLibCM_getTemperatureEnabled(void)
{
    return temperatureEnabled;
}


float EmonLibCM_getTemperature(char sensorNumber)
{
    int temp = temperatures[(unsigned char)sensorNumber];
    
    if (sensorNumber < 0 || sensorNumber >= temperatureMaxCount)
        return UNUSED_TEMPERATURE/100.0;
    if (temp >=30000)
        return temp/100.0;                                      // 300 series error codes are already set
    return (temp/100.0);
}


/**************************************************************************************************
*
*   'ADC COMPLETE' ISR
*
*
***************************************************************************************************/

ISR(ADC_vect) 
{
    EmonLibCM_interrupt();
}

/**************************************************************************************************
*
*   'PULSE INPUT' ISRs
*
*
***************************************************************************************************/
// The pulse interrupt routines - run each time a rising edge of a pulse is detected
  
void onPulse0(void) 
{
    onPulse(0);
}

void onPulse1(void) 
{
    onPulse(1);
}

void onPulse(byte channel)  
{         
    if (pulses[channel].PulseMinPeriod)
    {
        if ((millis() - pulses[channel].pulseTime) > pulses[channel].PulseMinPeriod)                   // Check that contact bounce has finished
            pulses[channel].pulseIncrement++;
        pulses[channel].pulseTime=millis(); 
    }
    else                                                               // No 'debounce' required - electronic switch presumed    
        pulses[channel].pulseIncrement++;                   
}