rk3566-orangepi-3b.dts

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
 *
 */
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pwm/pwm.h>
#include <dt-bindings/pinctrl/rockchip.h>
#include <dt-bindings/soc/rockchip,vop2.h>
#include "rk3566.dtsi"

/ {
	model = "Rockchip RK3566 OPi 3B";
	compatible = "rockchip,rk3566-orangepi-3b", "rockchip,rk3566";

	aliases {
		ethernet0 = &gmac1;
		mmc0 = &sdhci;
		mmc1 = &sdmmc0;
	};

	chosen: chosen {
		stdout-path = "serial2:1500000n8";
	};

	fan: pwm-fan {
		compatible = "pwm-fan";
		#cooling-cells = <2>;
		pwms = <&pwm7 0 50000 0>;
		cooling-levels = <0 50 100 150 200 255>;
		rockchip,temp-trips = <
			50000   1
			55000   2
			60000   3
			65000   4
			70000   5
		>;
	};

	hdmi-con {
		compatible = "hdmi-connector";
		type = "a";

		port {
			hdmi_con_in: endpoint {
				remote-endpoint = <&hdmi_out_con>;
			};
		};
	};

	leds: leds {
		compatible = "gpio-leds";
		pinctrl-names = "default";
		pinctrl-0 =<&leds_gpio>;

		led@1 {
			gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_HIGH>;
			label = "status_led";
			linux,default-trigger = "heartbeat";
		};
	};

	rk809-sound {
		compatible = "simple-audio-card";
		simple-audio-card,format = "i2s";
		simple-audio-card,name = "Analog RK809";
		simple-audio-card,mclk-fs = <256>;

		simple-audio-card,cpu {
			sound-dai = <&i2s1_8ch>;
		};

		simple-audio-card,codec {
			sound-dai = <&rk809>;
		};
	};

	sdio_pwrseq: sdio-pwrseq {
		compatible = "mmc-pwrseq-simple";
		clocks = <&rk809 1>;
		clock-names = "ext_clock";
		pinctrl-names = "default";
		pinctrl-0 = <&wifi_enable_h>;

		/*
		 * On the module itself this is one of these (depending
		 * on the actual card populated):
		 * - SDIO_RESET_L_WL_REG_ON
		 * - PDN (power down when low)
		 */
		post-power-on-delay-ms = <200>;
		reset-gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_LOW>;
	};

	sprd-mtty {
		compatible = "sprd,mtty";
		sprd,name = "ttyBT";
	};

	unisoc_uwe_bsp: uwe-bsp {
		compatible = "unisoc,uwe_bsp";
		wl-reg-on = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
		bt-reg-on = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
		wl-wake-host-gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>;
		bt-wake-host;
		bt-wake-host-gpio = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
		sdio-ext-int-gpio = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
		unisoc,btwf-file-name = "/lib/firmware/wcnmodem.bin";
		blksz-512;
		keep-power-on;
	};

	/* labeled +12v in schematic */
	vcc12v_dcin: vcc12v-dcin-regulator {
		compatible = "regulator-fixed";
		regulator-name = "vcc12v_dcin";
		regulator-always-on;
		regulator-boot-on;
		regulator-min-microvolt = <12000000>;
		regulator-max-microvolt = <12000000>;
	};

	/* labeled +5v in schematic */
	vcc_5v: vcc-5v-regulator {
		compatible = "regulator-fixed";
		regulator-name = "vcc_5v";
		regulator-always-on;
		regulator-boot-on;
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		vin-supply = <&vcc12v_dcin>;
	};

	vbus: vbus {
		compatible = "regulator-fixed";
		regulator-name = "vbus";
		regulator-always-on;
		regulator-boot-on;
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
	};

	/* labeled +3.3v For PCIe only in schematic */
	vcc3v3_pcie: vcc3v3-pcie-regulator {
		compatible = "regulator-fixed";
		regulator-name = "vcc3v3_pcie";
		regulator-always-on;
		regulator-boot-on;
		enable-active-high;
		gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&pcie_drv>;
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		vin-supply = <&vcc12v_dcin>;
	};

	vcc3v3_sys: vcc3v3-sys {
		compatible = "regulator-fixed";
		regulator-name = "vcc3v3_sys";
		regulator-always-on;
		regulator-boot-on;
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		vin-supply = <&vbus>;
	};

	vcc5v0_sys: vcc5v0-sys {
		compatible = "regulator-fixed";
		regulator-name = "vcc5v0_sys";
		regulator-always-on;
		regulator-boot-on;
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		vin-supply = <&vbus>;
	};

	vcc5v0_usb: vcc5v0-usb {
		compatible = "regulator-fixed";
		regulator-name = "vcc5v0_usb";
		regulator-always-on;
		regulator-boot-on;
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		vin-supply = <&vbus>;
	};

	vcc_sd: vcc-sd {
		compatible = "regulator-fixed";
		regulator-max-microvolt = <3300000>;
		regulator-min-microvolt = <3300000>;
		regulator-name = "vcc_sd";
		vin-supply = <&vcc3v3_sys>;
	};

	vcc5v0_host: vcc5v0-host-regulator {
		compatible = "regulator-fixed";
		enable-active-high;
		gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&vcc5v0_host_en>;
		regulator-name = "vcc5v0_host";
		regulator-always-on;
	};

	vcc5v0_otg: vcc5v0-otg-regulator {
		compatible = "regulator-fixed";
		enable-active-high;
		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&vcc5v0_otg_en>;
		regulator-name = "vcc5v0_otg";
		regulator-always-on;
	};
};

&combphy1 {
	status = "okay";
};

&combphy2 {
	status = "okay";
};

&cpu0 {
	cpu-supply = <&vdd_cpu>;
};

&cpu1 {
	cpu-supply = <&vdd_cpu>;
};

&cpu2 {
	cpu-supply = <&vdd_cpu>;
};

&cpu3 {
	cpu-supply = <&vdd_cpu>;
};

&gmac1 {
	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
	assigned-clock-rates = <0>, <125000000>;
	clock_in_out = "input";
	phy-mode = "rgmii";
	pinctrl-names = "default";
	pinctrl-0 = <&gmac1m0_miim
		     &gmac1m0_tx_bus2
		     &gmac1m0_rx_bus2
		     &gmac1m0_rgmii_clk
		     &gmac1m0_clkinout
		     &gmac1m0_rgmii_bus>;

	snps,reset-gpio = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
	snps,reset-active-low;
	/* Reset time is 20ms, 100ms for rtl8211f */
	//snps,reset-delays-us = <0 20000 100000>;
	snps,reset-delays-us = <0 50000 200000>;
	tx_delay = <0x30>;
	rx_delay = <0x10>;
	phy-handle = <&rgmii_phy0>;
	status = "okay";
};

&gpu {
	mali-supply = <&vdd_gpu>;
	status = "disabled";
};

&hdmi {
	avdd-0v9-supply = <&vdda0v9_image>;
	avdd-1v8-supply = <&vcca1v8_image>;
	status = "okay";
};

&hdmi_in {
	hdmi_in_vp0: endpoint {
		remote-endpoint = <&vp0_out_hdmi>;
		status = "okay";
	};
};

&hdmi_out {
	hdmi_out_con: endpoint {
		remote-endpoint = <&hdmi_con_in>;
		status = "okay";
	};
};

&hdmi_sound {
	status = "okay";
};

&i2c0 {
	status = "okay";

	vdd_cpu: syr837@40 {
		compatible = "silergy,syr827";
		reg = <0x40>;
		vin-supply = <&vcc5v0_sys>;
		regulator-compatible = "fan53555-reg";
		regulator-name = "vdd_cpu";
		regulator-min-microvolt = <712500>;
		regulator-max-microvolt = <1390000>;
		regulator-init-microvolt = <900000>;
		regulator-initial-mode = <1>;
		regulator-ramp-delay = <2300>;
		fcs,suspend-voltage-selector = <1>;
		regulator-boot-on;
		regulator-always-on;
		regulator-state-mem {
			regulator-off-in-suspend;
		};
	};

	rk809: pmic@20 {
		compatible = "rockchip,rk809";
		reg = <0x20>;
		interrupt-parent = <&gpio0>;
		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;

		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
		#clock-cells = <1>;
		clock-names = "mclk";
		clocks = <&cru I2S1_MCLKOUT_TX>;
		pinctrl-names = "default", "pmic-sleep",
				"pmic-power-off", "pmic-reset";
		pinctrl-0 = <&pmic_int>, <&i2s1m0_mclk>;
		pinctrl-1 = <&soc_slppin_slp>, <&rk817_slppin_slp>;
		pinctrl-2 = <&soc_slppin_gpio>, <&rk817_slppin_pwrdn>;
		pinctrl-3 = <&soc_slppin_gpio>, <&rk817_slppin_rst>;
		#sound-dai-cells = <0>;

		rockchip,system-power-controller;
		wakeup-source;

		vcc1-supply = <&vcc3v3_sys>;
		vcc2-supply = <&vcc3v3_sys>;
		vcc3-supply = <&vcc3v3_sys>;
		vcc4-supply = <&vcc3v3_sys>;
		vcc5-supply = <&vcc3v3_sys>;
		vcc6-supply = <&vcc3v3_sys>;
		vcc7-supply = <&vcc3v3_sys>;
		vcc8-supply = <&vcc3v3_sys>;
		vcc9-supply = <&vcc3v3_sys>;

		pinctrl_rk8xx: pinctrl_rk8xx {
			gpio-controller;
			#gpio-cells = <2>;

			rk817_slppin_null: rk817_slppin_null {
				pins = "gpio_slp";
				function = "pin_fun0";
			};

			rk817_slppin_slp: rk817_slppin_slp {
				pins = "gpio_slp";
				function = "pin_fun1";
			};

			rk817_slppin_pwrdn: rk817_slppin_pwrdn {
				pins = "gpio_slp";
				function = "pin_fun2";
			};

			rk817_slppin_rst: rk817_slppin_rst {
				pins = "gpio_slp";
				function = "pin_fun3";
			};
		};

		regulators {
			vdd_logic: DCDC_REG1 {
				regulator-always-on;
				regulator-boot-on;
				regulator-min-microvolt = <500000>;
				regulator-max-microvolt = <1350000>;
				regulator-init-microvolt = <900000>;
				regulator-ramp-delay = <6001>;
				regulator-initial-mode = <0x2>;
				regulator-name = "vdd_logic";
				regulator-state-mem {
					regulator-off-in-suspend;
				};
			};

			vdd_gpu: DCDC_REG2 {
				regulator-always-on;
				regulator-boot-on;
				regulator-min-microvolt = <500000>;
				regulator-max-microvolt = <1350000>;
				regulator-init-microvolt = <900000>;
				regulator-ramp-delay = <6001>;
				regulator-initial-mode = <0x2>;
				regulator-name = "vdd_gpu";
				regulator-state-mem {
					regulator-off-in-suspend;
				};
			};

			vcc_ddr: DCDC_REG3 {
				regulator-always-on;
				regulator-boot-on;
				regulator-initial-mode = <0x2>;
				regulator-name = "vcc_ddr";
				regulator-state-mem {
					regulator-on-in-suspend;
				};
			};

			vdd_npu: DCDC_REG4 {
				regulator-always-on;
				regulator-boot-on;
				regulator-min-microvolt = <500000>;
				regulator-max-microvolt = <1350000>;
				regulator-init-microvolt = <900000>;
				regulator-ramp-delay = <6001>;
				regulator-initial-mode = <0x2>;
				regulator-name = "vdd_npu";
				regulator-state-mem {
					regulator-off-in-suspend;
				};
			};

			vdda0v9_image: LDO_REG1 {
				regulator-boot-on;
				regulator-always-on;
				regulator-min-microvolt = <900000>;
				regulator-max-microvolt = <900000>;
				regulator-name = "vdda0v9_image";
				regulator-state-mem {
					regulator-off-in-suspend;
				};
			};

			vdda_0v9: LDO_REG2 {
				regulator-always-on;
				regulator-boot-on;
				regulator-min-microvolt = <900000>;
				regulator-max-microvolt = <900000>;
				regulator-name = "vdda_0v9";
				regulator-state-mem {
					regulator-off-in-suspend;
				};
			};

			vdda0v9_pmu: LDO_REG3 {
				regulator-always-on;
				regulator-boot-on;
				regulator-min-microvolt = <900000>;
				regulator-max-microvolt = <900000>;
				regulator-name = "vdda0v9_pmu";
				regulator-state-mem {
					regulator-on-in-suspend;
					regulator-suspend-microvolt = <900000>;
				};
			};

			vccio_acodec: LDO_REG4 {
				regulator-always-on;
				regulator-boot-on;
				regulator-min-microvolt = <3000000>;
				regulator-max-microvolt = <3000000>;
				regulator-name = "vccio_acodec";
				regulator-state-mem {
					regulator-off-in-suspend;
				};
			};

			vccio_sd: LDO_REG5 {
				regulator-always-on;
				regulator-boot-on;
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <3300000>;
				regulator-name = "vccio_sd";
				regulator-state-mem {
					regulator-off-in-suspend;
				};
			};

			vcc3v3_pmu: LDO_REG6 {
				regulator-always-on;
				regulator-boot-on;
				regulator-min-microvolt = <3300000>;
				regulator-max-microvolt = <3300000>;
				regulator-name = "vcc3v3_pmu";
				regulator-state-mem {
					regulator-on-in-suspend;
					regulator-suspend-microvolt = <3300000>;
				};
			};

			vcca_1v8: LDO_REG7 {
				regulator-always-on;
				regulator-boot-on;
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-name = "vcca_1v8";
				regulator-state-mem {
					regulator-off-in-suspend;
				};
			};

			vcca1v8_pmu: LDO_REG8 {
				regulator-always-on;
				regulator-boot-on;
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-name = "vcca1v8_pmu";
				regulator-state-mem {
					regulator-on-in-suspend;
					regulator-suspend-microvolt = <1800000>;
				};
			};

			vcca1v8_image: LDO_REG9 {
				regulator-always-on;
				regulator-boot-on;
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-name = "vcca1v8_image";
				regulator-state-mem {
					regulator-off-in-suspend;
				};
			};

			vcc_1v8: DCDC_REG5 {
				regulator-always-on;
				regulator-boot-on;
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <1800000>;
				regulator-name = "vcc_1v8";
				regulator-state-mem {
					regulator-off-in-suspend;
				};
			};

			vcc_3v3: SWITCH_REG1 {
				regulator-always-on;
				regulator-boot-on;
				regulator-name = "vcc_3v3";
				regulator-state-mem {
					regulator-off-in-suspend;
				};
			};

			vcc3v3_sd: SWITCH_REG2 {
				regulator-always-on;
				regulator-boot-on;
				regulator-name = "vcc3v3_sd";
				regulator-state-mem {
					regulator-off-in-suspend;
				};
			};
		};

		codec {
			mic-in-differential;
		};
	};
};

&spi3 {
	status = "disabled";
	pinctrl-names = "default";
	pinctrl-0 = <&spi3m0_cs1 &spi3m0_pins>;

	spi_dev@0 {
		compatible = "armbian,spi-dev";
		reg = <0>;
		spi-max-frequency = <50000000>;
	};
};

/*
 * i2c3_m0 is exposed on the 40-pin (green connectors)
 * pin 27 - i2c3_sda_m0
 * pin 28 - i2c3_scl_m0
 */
&i2c3 {
	status = "disabled";
};

&i2c2 {
	pinctrl-0 = <&i2c2m1_xfer>;
	status = "disabled";
};

&i2c4 {
	status = "disabled";
};

&i2s0_8ch {
	status = "okay";
};

&i2s1_8ch {
	pinctrl-names = "default";
	pinctrl-0 = <&i2s1m0_sclktx
		     &i2s1m0_lrcktx
		     &i2s1m0_sdi0
		     &i2s1m0_sdo0>;
	rockchip,trcm-sync-tx-only;
	status = "okay";
};

&mdio1 {
	rgmii_phy0: phy@0 {
		compatible = "ethernet-phy-ieee802.3-c22";
		reg = <0x0>;
	};
};

&pcie2x1 {
	reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
	vpcie3v3-supply = <&vcc3v3_pcie>;
	status = "okay";
};

&pinctrl {
	wireless-bluetooth {
		uart1_gpios: uart1-gpios {
			rockchip,pins = <2 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
		};
	};

	sd {
		sdmmc0_pwr_h: sdmmc0-pwr-h {
			rockchip,pins =
			        <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
		};
	};

	mxc6655xa {
		mxc6655xa_irq_gpio: mxc6655xa_irq_gpio {
			rockchip,pins = <3 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
		};
	};

	pmic {
		pmic_int: pmic_int {
			rockchip,pins =
				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
		};

		soc_slppin_gpio: soc_slppin_gpio {
			rockchip,pins =
				<0 RK_PA2 RK_FUNC_GPIO &pcfg_output_low>;
		};

		soc_slppin_slp: soc_slppin_slp {
			rockchip,pins =
				<0 RK_PA2 1 &pcfg_pull_none>;
		};

		soc_slppin_rst: soc_slppin_rst {
			rockchip,pins =
				<0 RK_PA2 2 &pcfg_pull_none>;
		};
	};

	touch {
		touch_gpio: touch-gpio {
			rockchip,pins =
				<0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>,
				<0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
		};
	};

	sdio-pwrseq {
		wifi_enable_h: wifi-enable-h {
			rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
		};
	};

	usb {
		vcc5v0_host_en: vcc5v0-host-en {
			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
		};

		vcc5v0_otg_en: vcc5v0-otg-en {
			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
		};
	};

	work-led {
		leds_gpio: leds-gpio {
			rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
		};
	};

	headphone {
		hp_det: hp-det {
			rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>;
		};
	};

	pcie {
		pcie_drv: pcie-drv {
			rockchip,pins =
				<0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
		};
	};

	edp {
	        edp_hpd: edp-hpd {
	                rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
	        };

	        bl_en: bl-en {
	                rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_output_high>;
	        };
	};
};

 /*
  * There are 10 independent IO domains in RK3566/RK3568, including PMUIO[0:2] and VCCIO[1:7].
  * 1/ PMUIO0 and PMUIO1 are fixed-level power domains which cannot be configured;
  * 2/ PMUIO2 and VCCIO1,VCCIO[3:7] domains require that their hardware power supply voltages
  *    must be consistent with the software configuration correspondingly
  *	a/ When the hardware IO level is connected to 1.8V, the software voltage configuration
  *	   should also be configured to 1.8V accordingly;
  *	b/ When the hardware IO level is connected to 3.3V, the software voltage configuration
  *	   should also be configured to 3.3V accordingly;
  * 3/ VCCIO2 voltage control selection (0xFDC20140)
  *	BIT[0]: 0x0: from GPIO_0A7 (default)
  *	BIT[0]: 0x1: from GRF
  *    Default is determined by Pin FLASH_VOL_SEL/GPIO0_A7:
  *	L:VCCIO2 must supply 3.3V
  *	H:VCCIO2 must supply 1.8V
  */

&pmu_io_domains {
        status = "okay";
        pmuio1-supply = <&vcc3v3_pmu>;
        pmuio2-supply = <&vcc3v3_pmu>;
        vccio1-supply = <&vcc_3v3>;
	vccio2-supply = <&vcc_1v8>;
        vccio3-supply = <&vccio_sd>;
        vccio4-supply = <&vcc_1v8>;
        vccio5-supply = <&vcc_3v3>;
        vccio6-supply = <&vcc_3v3>;
        vccio7-supply = <&vcc_3v3>;
};

&pwm7 {
	status = "okay";
};

&pwm11 {
	pinctrl-0 = <&pwm11m1_pins>;
	status = "disabled";
};

&pwm15 {
	pinctrl-0 = <&pwm15m1_pins>;
	status = "disabled";
};

&saradc {
	status = "okay";
	vref-supply = <&vcca_1v8>;
};

&sdhci {
	bus-width = <8>;
	max-frequency = <200000000>;
	non-removable;
	pinctrl-names = "default";
	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>;
	status = "okay";
};

&sdmmc0 {
	max-frequency = <150000000>;
	bus-width = <4>;
	cap-mmc-highspeed;
	cap-sd-highspeed;
	disable-wp;
	sd-uhs-sdr104;
	vmmc-supply = <&vcc_sd>;
	vqmmc-supply = <&vccio_sd>;
	pinctrl-names = "default";
	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
	status = "okay";
};

&sdmmc1 {
	max-frequency = <150000000>;
	bus-width = <4>;
	disable-wp;
	cap-sd-highspeed;
	cap-sdio-irq;
	keep-power-in-suspend;
	mmc-pwrseq = <&sdio_pwrseq>;
	non-removable;
	pinctrl-names = "default";
	pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
	sd-uhs-sdr104;
	status = "okay";
};

&sfc {
	#address-cells = <1>;
	#size-cells = <0>;
	status = "okay";
	flash@0 {
		compatible = "jedec,spi-nor";
		reg = <0>;
		spi-max-frequency = <100000000>;
		spi-rx-bus-width = <4>;
		spi-tx-bus-width = <1>;
	};
};

&tsadc {
	status = "okay";
};

&uart1 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
	uart-has-rtscts;
};

/* (debug) uart2 has connectors near the usb-c power, but also on the 40-pin pins 6 (tx) and 8 (rx) - don't wire both */
&uart2 {
	status = "okay";
};

&uart3 {
	status = "disabled";
};

&uart7 {
	pinctrl-0 = <&uart7m2_xfer>;
	status = "disabled";
};

&uart9 {
    pinctrl-0 = <&uart9m2_xfer>;
    status = "disabled";
};

&usb2phy0 {
	status = "okay";
};

&usb2phy0_host {
	phy-supply = <&vbus>;
	status = "okay";
};

&usb2phy0_otg {
	status = "okay";
};

&usb2phy1 {
	status = "okay";
};

&usb2phy1_host {
	status = "okay";
};

&usb2phy1_otg {
	status = "okay";
};

&usb_host0_ehci {
	status = "okay";
};

&usb_host0_ohci {
	status = "okay";
};

&usb_host0_xhci {
	dr_mode = "host";
	extcon = <&usb2phy0>;
	status = "okay";
};

&usb_host1_ehci {
	status = "okay";
};

&usb_host1_ohci {
	status = "okay";
};

&usb_host1_xhci {
	status = "okay";
};

&vop {
	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
	status = "okay";
};

&vop_mmu {
	status = "okay";
};

&vp0 {
	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
		remote-endpoint = <&hdmi_in_vp0>;
		status = "okay";
	};
};