forked from cleanflight/cleanflight
/
target.h
116 lines (95 loc) · 3.24 KB
/
target.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
/*
* This file is part of Cleanflight.
*
* Cleanflight is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* Cleanflight is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with Cleanflight. If not, see <http://www.gnu.org/licenses/>.
*/
#pragma once
#define TARGET_BOARD_IDENTIFIER "OLI1" // Olimexino
//#define OLIMEXINO_UNCUT_LED1_E_JUMPER
//#define OLIMEXINO_UNCUT_LED2_E_JUMPER
#ifdef OLIMEXINO_UNCUT_LED1_E_JUMPER
#define LED0_GPIO GPIOA
#define LED0_PIN Pin_5 // D13, PA5/SPI1_SCK/ADC5 - "LED1" on silkscreen, Green
#define LED0_PERIPHERAL RCC_APB2Periph_GPIOA
#define LED0
#endif
#ifdef OLIMEXINO_UNCUT_LED2_E_JUMPER
// "LED2" is using one of the PWM pins (CH2/PWM2), so we must not use PWM2 unless the jumper is cut. @See pwmInit()
#define LED1_GPIO GPIOA
#define LED1_PIN Pin_1 // D3, PA1/USART2_RTS/ADC1/TIM2_CH3 - "LED2" on silkscreen, Yellow
#define LED1_PERIPHERAL RCC_APB2Periph_GPIOA
#define LED1
#endif
#define GYRO
#define USE_FAKE_GYRO
//#define USE_GYRO_L3G4200D
//#define USE_GYRO_L3GD20
//#define USE_GYRO_MPU3050
#define USE_GYRO_MPU6050
//#define USE_GYRO_SPI_MPU6000
//#define USE_GYRO_SPI_MPU6500
#define ACC
#define USE_FAKE_ACC
//#define USE_ACC_ADXL345
//#define USE_ACC_BMA280
//#define USE_ACC_MMA8452
//#define USE_ACC_LSM303DLHC
#define USE_ACC_MPU6050
//#define USE_ACC_SPI_MPU6000
//#define USE_ACC_SPI_MPU6500
#define BARO
//#define USE_BARO_MS5611
#define USE_BARO_BMP085
#define USE_BARO_BMP280
#define MAG
#define USE_MAG_HMC5883
#define SONAR
#define USE_USART1
#define USE_USART2
#define USE_SOFTSERIAL1
#define USE_SOFTSERIAL2
#define SERIAL_PORT_COUNT 4
#define SOFTSERIAL_1_TIMER TIM3
#define SOFTSERIAL_1_TIMER_RX_HARDWARE 4 // PWM 5
#define SOFTSERIAL_1_TIMER_TX_HARDWARE 5 // PWM 6
#define SOFTSERIAL_2_TIMER TIM3
#define SOFTSERIAL_2_TIMER_RX_HARDWARE 6 // PWM 7
#define SOFTSERIAL_2_TIMER_TX_HARDWARE 7 // PWM 8
#define USE_I2C
#define I2C_DEVICE (I2CDEV_2)
// #define SOFT_I2C // enable to test software i2c
// #define SOFT_I2C_PB1011 // If SOFT_I2C is enabled above, need to define pinout as well (I2C1 = PB67, I2C2 = PB1011)
// #define SOFT_I2C_PB67
#define USE_ADC
#define CURRENT_METER_ADC_GPIO GPIOB
#define CURRENT_METER_ADC_GPIO_PIN GPIO_Pin_1
#define CURRENT_METER_ADC_CHANNEL ADC_Channel_9
#define VBAT_ADC_GPIO GPIOA
#define VBAT_ADC_GPIO_PIN GPIO_Pin_4
#define VBAT_ADC_CHANNEL ADC_Channel_4
#define RSSI_ADC_GPIO GPIOA
#define RSSI_ADC_GPIO_PIN GPIO_Pin_1
#define RSSI_ADC_CHANNEL ADC_Channel_1
#define EXTERNAL1_ADC_GPIO GPIOA
#define EXTERNAL1_ADC_GPIO_PIN GPIO_Pin_5
#define EXTERNAL1_ADC_CHANNEL ADC_Channel_5
#define GPS
#define LED_STRIP
#define LED_STRIP_TIMER TIM3
#define TELEMETRY
#define SERIAL_RX
#define AUTOTUNE
#define BLACKBOX
#define USE_SERVOS
#define USE_CLI