Skip to content

Latest commit

 

History

History
91 lines (84 loc) · 4.03 KB

Parts.md

File metadata and controls

91 lines (84 loc) · 4.03 KB
Raw

Parts List for the Stackable 6502 Computer

There is no kit that you can buy yet for this design, but if you have already built or plan to build Ben Eater's Breadboard 6502 Computer, then most of the components can be gotten from his kits. Build the breadboard version first, following his instructions on YouTube. Then solder up a permanent one using the same parts plus a few extras!

You will need at least the basic "6502 Computer Kit", the "6502 Serial Interface Kit", and of course an "EEPROM Programmer". I have marked the parts that you can get from Ben's kits with (BE) below.

Base Board

  • PCB; see the gerber/BaseBoard directory for the 4-layer Gerbers, or purchase it from PCBway.
  • Integrated Circuits:
    • 1 x W65C02SxP microprocessor, 40-pin DIP (BE)
    • 1 x W65C22NxP Versatile Interface Adapter, 40-pin DIP (VIA) (BE)
    • 1 x 62256 32 kByte static RAM, 28-pin DIP (BE)
    • 1 x 28C256 32 kByte EEPROM, 28-pin DIP (BE)
    • 1 x 74LS00 or 74HC00 NAND gate (not needed if using the ATF22V10C-7PX), 14-pin DIP (BE)
    • 1 x ATF22V10C-7PX Programmable Logic Device, 24-pin DIP (optional)
    • 1 x LM7805 5V voltage regulator (TO-220 package)
    • 1 x L78L33 3.3V voltage regulator (TO-92 package) (optional, 3.3V supply only)
  • IC Sockets:
    • 2 x 40-pin wide DIP sockets (15.24mm width) (for W65C02SxP and W65C22NxP)
    • 1 x 14-pin narrow DIP socket (7.62mm width) (for 74LS00)
    • 1 x 28-pin wide DIP socket (15.24mm width) (for 62256)
    • 1 x 24-pin narrow DIP socket (7.62mm width) (for ATF22V10C-7PX)
    • 1 x 28-pin ZIF socket (for 28C256, or use an ordinary 28-pin wide DIP socket instead)
  • Resistors:
    • 1 x 220R resistor (BE)
    • 1 x 1K resistor (BE)
    • 2 x 3.3K resistor
    • 2 x 10K resistor
  • Capacitors:
    • 9 x 100nF ceramic or monolithic capacitor (BE)
    • 1 x 330nF ceramic or monolithic capacitor (220nF is sufficient in a pinch)
    • 1 x 47uF electrolytic capacitor, 16V rating or better
  • Diodes and LED's:
    • 2 x Schottky diodes, 1N5189, SB140, or equivalent
    • 1 x 5mm LED for power indication (red, green, blue, etc - your choice) (BE)
  • Stackable pin headers, 2.54mm pitch:
    • 2 x 6-pin
    • 1 x 10-pin
    • 1 x 20-pin
    • 2 x 16-pin
  • Other:
    • 1 x 1MHz crystal oscillator module in either 14-pin or 8-pin DIP package (BE)
    • 1 x pushbutton switch for RESET
    • 1 x SPDT slider switch for power (can be mounted off-board)
    • 1 x DC barrel jack
    • 1 x 2-pin 2.54mm header plus jumper if using the 74LS00 and JP1
    • 1 x 9V or 12V DC plug pack / wall wart

I/O Board

  • PCB; see the gerber/IoBoard directory for the 4-layer Gerbers, or purchase it from PCBway.
  • Integrated Circuits:
    • W65C51NxP Asynchronous Communications Interface Adapter (ACIA), 28-pin DIP (BE)
    • MAX232 RS-232 line driver, 16-pin DIP (BE)
    • MCP3208 12-bit SPI ADC, 16-pin DIP (optional, only needed if you need analog inputs)
  • IC Sockets:
    • 1 x 28-pin wide DIP socket (15.24mm width) (for W65C51NxP)
    • 2 x 16-pin narrow DIP sockets (7.62mm width) (for MAX232 and MCP3208)
  • Resistors:
    • 5 x 220R resistor (BE)
    • 1 x 1M resistor
  • Capacitors:
    • 2 x 100nF ceramic or monolithic capacitor (BE)
    • 1 x 22pF ceramic capacitor (20pF or 30pF will also work) (BE)
    • 1 x 1uF ceramic or non-polarized capacitor (BE)
  • Diodes and LED's:
    • 1 x Schottky diode, 1N5189, SB140, or equivalent
    • 5 x 3mm red or green LED's for power indication and digital outputs (5mm will also work - BE)
  • Stackable pin headers, 2.54mm pitch:
    • 2 x 6-pin
    • 1 x 10-pin
    • 1 x 20-pin
    • 2 x 16-pin
  • Other:
    • 1 x 1.8432MHz crystal oscillator module in HC49 package (BE)
    • 1 x DB9 female right angle connector
    • 2 x 2.54mm low height 8-pin headers for the SD card interface and analogs
    • 1 x 2.54mm low height 2-pin header for the PWM connector