printer-20230202_133453.cfg

# This file contains common pin mappings for the BigTreeTech Octopus V1.
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference

# after running "make", copy the generated "klipper/out/klipper.bin" file to a
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.

# See docs/Config_Reference.md for a description of parameters.

[include pin_aliases_octopus.cfg]
[include mainsail.cfg]
[include toolhead0.cfg]
[include toolhead1.cfg]
[include macros.cfg]
[include IDEX_mode.cfg]
[include lights.cfg]
[include klicky.cfg]

[mcu]
##  Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
##--------------------------------------------------------------------
# Starts as: serial: /dev/serial/by-id/usb-STMicroelectronics_BIGTREE_OCTOPUS_CDC_in_FS_Mode_204331844E53-if00
# After first build:
serial: /dev/serial0
restart_method: command
##--------------------------------------------------------------------

[force_move]
enable_force_move: true

# Intentionally slow until limits are determined and stepper currents are set correctly.
[printer]
kinematics: hybrid_corexy
max_velocity: 200
max_accel: 2000
max_z_velocity: 100
max_z_accel: 200
square_corner_velocity: 5.0

#####################################################################
#   X Steppers
#####################################################################

##  Right Extruder X motor (when looking at the front)
##  Connected to MOTOR_0
##  Endstop connected to DIAG_0
[stepper_x]
step_pin: mcu:MOT1_STEP
dir_pin: mcu:MOT1_DIR
enable_pin: !mcu:MOT1_EN
rotation_distance: 40
microsteps: 32
full_steps_per_rotation: 200
# Uncomment below if using direct inputs on Octo
#endstop_pin: ^PG6#
endstop_pin: ^head0:PB5

position_endstop: -50
position_min: -52
position_max: 228

homing_speed: 60
homing_retract_dist: 5
second_homing_speed: 10

[tmc2209 stepper_x]
uart_pin: mcu:MOT1_CS
run_current: 0.4
stealthchop_threshold: 500

##  Left Extruder X motor (when looking at the front)
##  Connected to MOTOR_2
##  Endstop connected to DIAG_2
[dual_carriage]
axis: x
step_pin: mcu:MOT0_STEP
dir_pin: mcu:MOT0_DIR
enable_pin: !mcu:MOT0_EN
rotation_distance: 40
microsteps: 32
full_steps_per_rotation: 200
endstop_pin: ^head1:PB5

position_endstop: 22.4
position_min: 22
position_max: 300

homing_speed: 60
homing_retract_dist: 10
second_homing_speed: 10

[tmc2209 dual_carriage]
uart_pin: mcu:MOT0_CS
run_current: 0.4
stealthchop_threshold: 500

##--------------------------------------------------------------------
##  Right Y motor (when looking at the front)
##  Connected to MOTOR_1
##  Endstop connected to DIAG_1
[stepper_y]
step_pin: mcu:MOT2_STEP
dir_pin: !mcu:MOT2_DIR
enable_pin: !mcu:MOT2_EN
rotation_distance: 40
microsteps: 32
full_steps_per_rotation:200
endstop_pin: ^mcu:ESTOP1

position_endstop: 255
position_max: 255
position_min: -5

homing_speed: 40
homing_retract_dist: 5

[tmc2209 stepper_y]
uart_pin: mcu:MOT2_CS
run_current: 0.4
stealthchop_threshold: 500

##  Left Y motor (when looking at the front)
##  Connected to MOTOR_3
##  Endstop connected to DIAG_3
[stepper_y1]
step_pin: mcu:MOT3_STEP
dir_pin: mcu:MOT3_DIR
enable_pin: !mcu:MOT3_EN
rotation_distance: 40
microsteps: 32
full_steps_per_rotation:200
endstop_pin: ^mcu:ESTOP2

[tmc2209 stepper_y1]
uart_pin: mcu:MOT3_CS
run_current: 0.4
stealthchop_threshold: 500

#####################################################################
#   Z Stepper Settings
#####################################################################
## Z0 Stepper - Front Right

##  Connected to MOTOR_4
##  Endstop connected to DIAG_4
[stepper_z]
step_pin: mcu:MOT4_STEP
dir_pin: !mcu:MOT4_DIR
enable_pin: !mcu:MOT4_EN
rotation_distance: 40
gear_ratio: 80:16
microsteps: 16
endstop_pin: ^mcu:ESTOP0

##  Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
##  (+) value = endstop above Z0, (-) value = endstop below
##  Increasing position_endstop brings nozzle closer to the bed
##  After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
position_endstop: 0
position_max: 120

position_min: -5
homing_speed: 5
second_homing_speed: 3
homing_retract_dist: 2

##  Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 stepper_z]
uart_pin: mcu:MOT4_CS
interpolate: false
run_current: 0.7
sense_resistor: 0.110
stealthchop_threshold: 500

## Z1 Stepper - Front Left
[stepper_z1]
step_pin: mcu:MOT5_STEP
dir_pin: mcu:MOT5_DIR
enable_pin: !mcu:MOT5_EN
rotation_distance: 40
gear_ratio: 80:16
microsteps: 16

##	Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 stepper_z1]
uart_pin: mcu:MOT5_CS
interpolate: false
run_current: 0.7
sense_resistor: 0.110
stealthchop_threshold: 500

## Z2 Stepper - Rear
[stepper_z2]
step_pin: mcu:MOT6_STEP
dir_pin: mcu:MOT6_DIR
enable_pin: !mcu:MOT6_EN
rotation_distance: 40
gear_ratio: 80:16
microsteps: 16

##	Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 stepper_z2]
uart_pin: mcu:MOT6_CS
interpolate: false
run_current: 0.7
sense_resistor: 0.110
stealthchop_threshold: 500

[heater_bed]
heater_pin: mcu:BED_OUT
sensor_type: Generic 3950
sensor_pin: mcu:TB
max_power: 0.9
pwm_cycle_time: 0.017
min_temp: 0
max_temp: 120
#control = pid
#pid_kp = 41.995
#pid_ki = 0.798
#pid_kd = 552.754

[probe]
##	Inductive Probe - Connected to Z MAX
##	This probe is not used for Z height, only Quad Gantry Leveling
##	Connected to Probe Pins
##	If your probe is NO instead of NC, change pin to !PA3
pin: head0:PB6
z_offset: 6.1
x_offset: 0 
y_offset: 21
speed: 5
samples: 3
samples_tolerance: 0.006
samples_result: median
samples_tolerance_retries: 5

[z_tilt]
##	Use Z_TILT_ADJUST to level the bed left to right.
##	z_positions: Location of toolhead
z_positions:
	-88,0
	125,325	
	338,0
points:
	30,30
	125,220
	220,30
speed: 150
horizontal_move_z: 50
retries: 5
retry_tolerance: 0.01

[bed_mesh]
speed: 300
horizontal_move_z: 10
mesh_min: 30, 30
mesh_max: 220, 220
fade_start: 0.6
fade_end: 10.0
probe_count: 5,5
algorithm: bicubic
relative_reference_index: 12

[temperature_sensor raspberry_pi]
sensor_type: temperature_host
min_temp: 0
max_temp: 100

[temperature_sensor mcu_temp]
sensor_type: temperature_mcu

[temperature_sensor PSU]
sensor_type: Generic 3950
sensor_pin: mcu:T1

[temperature_sensor Steppers]
sensor_type: Generic 3950
sensor_pin: mcu:T2

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 34.060
#*# pid_ki = 5.975
#*# pid_kd = 48.535