entry_64_compat.S

/* SPDX-License-Identifier: GPL-2.0 */
/*
 * Compatibility mode system call entry point for x86-64.
 *
 * Copyright 2000-2002 Andi Kleen, SuSE Labs.
 */
#include <asm/asm-offsets.h>
#include <asm/current.h>
#include <asm/errno.h>
#include <asm/ia32_unistd.h>
#include <asm/thread_info.h>
#include <asm/segment.h>
#include <asm/irqflags.h>
#include <asm/asm.h>
#include <asm/smap.h>
#include <asm/nospec-branch.h>
#include <linux/linkage.h>
#include <linux/err.h>

#include "calling.h"

	.section .entry.text, "ax"

/*
 * 32-bit SYSENTER entry.
 *
 * 32-bit system calls through the vDSO's __kernel_vsyscall enter here
 * on 64-bit kernels running on Intel CPUs.
 *
 * The SYSENTER instruction, in principle, should *only* occur in the
 * vDSO.  In practice, a small number of Android devices were shipped
 * with a copy of Bionic that inlined a SYSENTER instruction.  This
 * never happened in any of Google's Bionic versions -- it only happened
 * in a narrow range of Intel-provided versions.
 *
 * SYSENTER loads SS, RSP, CS, and RIP from previously programmed MSRs.
 * IF and VM in RFLAGS are cleared (IOW: interrupts are off).
 * SYSENTER does not save anything on the stack,
 * and does not save old RIP (!!!), RSP, or RFLAGS.
 *
 * Arguments:
 * eax  system call number
 * ebx  arg1
 * ecx  arg2
 * edx  arg3
 * esi  arg4
 * edi  arg5
 * ebp  user stack
 * 0(%ebp) arg6
 */
SYM_CODE_START(entry_SYSENTER_compat)
	UNWIND_HINT_ENTRY
	ENDBR
	/* Interrupts are off on entry. */
	swapgs

	pushq	%rax
	SWITCH_TO_KERNEL_CR3 scratch_reg=%rax
	popq	%rax

	movq	PER_CPU_VAR(pcpu_hot + X86_top_of_stack), %rsp

	/* Construct struct pt_regs on stack */
	pushq	$__USER_DS		/* pt_regs->ss */
	pushq	$0			/* pt_regs->sp = 0 (placeholder) */

	/*
	 * Push flags.  This is nasty.  First, interrupts are currently
	 * off, but we need pt_regs->flags to have IF set.  Second, if TS
	 * was set in usermode, it's still set, and we're singlestepping
	 * through this code.  do_SYSENTER_32() will fix up IF.
	 */
	pushfq				/* pt_regs->flags (except IF = 0) */
	pushq	$__USER32_CS		/* pt_regs->cs */
	pushq	$0			/* pt_regs->ip = 0 (placeholder) */
SYM_INNER_LABEL(entry_SYSENTER_compat_after_hwframe, SYM_L_GLOBAL)

	/*
	 * User tracing code (ptrace or signal handlers) might assume that
	 * the saved RAX contains a 32-bit number when we're invoking a 32-bit
	 * syscall.  Just in case the high bits are nonzero, zero-extend
	 * the syscall number.  (This could almost certainly be deleted
	 * with no ill effects.)
	 */
	movl	%eax, %eax

	pushq	%rax			/* pt_regs->orig_ax */
	PUSH_AND_CLEAR_REGS rax=$-ENOSYS
	UNWIND_HINT_REGS

	cld

	IBRS_ENTER
	UNTRAIN_RET
	CLEAR_BRANCH_HISTORY

	/*
	 * SYSENTER doesn't filter flags, so we need to clear NT and AC
	 * ourselves.  To save a few cycles, we can check whether
	 * either was set instead of doing an unconditional popfq.
	 * This needs to happen before enabling interrupts so that
	 * we don't get preempted with NT set.
	 *
	 * If TF is set, we will single-step all the way to here -- do_debug
	 * will ignore all the traps.  (Yes, this is slow, but so is
	 * single-stepping in general.  This allows us to avoid having
	 * a more complicated code to handle the case where a user program
	 * forces us to single-step through the SYSENTER entry code.)
	 *
	 * NB.: .Lsysenter_fix_flags is a label with the code under it moved
	 * out-of-line as an optimization: NT is unlikely to be set in the
	 * majority of the cases and instead of polluting the I$ unnecessarily,
	 * we're keeping that code behind a branch which will predict as
	 * not-taken and therefore its instructions won't be fetched.
	 */
	testl	$X86_EFLAGS_NT|X86_EFLAGS_AC|X86_EFLAGS_TF, EFLAGS(%rsp)
	jnz	.Lsysenter_fix_flags
.Lsysenter_flags_fixed:

	movq	%rsp, %rdi
	call	do_SYSENTER_32
	/* XEN PV guests always use IRET path */
	ALTERNATIVE "testl %eax, %eax; jz swapgs_restore_regs_and_return_to_usermode", \
		    "jmp swapgs_restore_regs_and_return_to_usermode", X86_FEATURE_XENPV
	jmp	sysret32_from_system_call

.Lsysenter_fix_flags:
	pushq	$X86_EFLAGS_FIXED
	popfq
	jmp	.Lsysenter_flags_fixed
SYM_INNER_LABEL(__end_entry_SYSENTER_compat, SYM_L_GLOBAL)
SYM_CODE_END(entry_SYSENTER_compat)

/*
 * 32-bit SYSCALL entry.
 *
 * 32-bit system calls through the vDSO's __kernel_vsyscall enter here
 * on 64-bit kernels running on AMD CPUs.
 *
 * The SYSCALL instruction, in principle, should *only* occur in the
 * vDSO.  In practice, it appears that this really is the case.
 * As evidence:
 *
 *  - The calling convention for SYSCALL has changed several times without
 *    anyone noticing.
 *
 *  - Prior to the in-kernel X86_BUG_SYSRET_SS_ATTRS fixup, anything
 *    user task that did SYSCALL without immediately reloading SS
 *    would randomly crash.
 *
 *  - Most programmers do not directly target AMD CPUs, and the 32-bit
 *    SYSCALL instruction does not exist on Intel CPUs.  Even on AMD
 *    CPUs, Linux disables the SYSCALL instruction on 32-bit kernels
 *    because the SYSCALL instruction in legacy/native 32-bit mode (as
 *    opposed to compat mode) is sufficiently poorly designed as to be
 *    essentially unusable.
 *
 * 32-bit SYSCALL saves RIP to RCX, clears RFLAGS.RF, then saves
 * RFLAGS to R11, then loads new SS, CS, and RIP from previously
 * programmed MSRs.  RFLAGS gets masked by a value from another MSR
 * (so CLD and CLAC are not needed).  SYSCALL does not save anything on
 * the stack and does not change RSP.
 *
 * Note: RFLAGS saving+masking-with-MSR happens only in Long mode
 * (in legacy 32-bit mode, IF, RF and VM bits are cleared and that's it).
 * Don't get confused: RFLAGS saving+masking depends on Long Mode Active bit
 * (EFER.LMA=1), NOT on bitness of userspace where SYSCALL executes
 * or target CS descriptor's L bit (SYSCALL does not read segment descriptors).
 *
 * Arguments:
 * eax  system call number
 * ecx  return address
 * ebx  arg1
 * ebp  arg2	(note: not saved in the stack frame, should not be touched)
 * edx  arg3
 * esi  arg4
 * edi  arg5
 * esp  user stack
 * 0(%esp) arg6
 */
SYM_CODE_START(entry_SYSCALL_compat)
	UNWIND_HINT_ENTRY
	ENDBR
	/* Interrupts are off on entry. */
	swapgs

	/* Stash user ESP */
	movl	%esp, %r8d

	/* Use %rsp as scratch reg. User ESP is stashed in r8 */
	SWITCH_TO_KERNEL_CR3 scratch_reg=%rsp

	/* Switch to the kernel stack */
	movq	PER_CPU_VAR(pcpu_hot + X86_top_of_stack), %rsp

SYM_INNER_LABEL(entry_SYSCALL_compat_safe_stack, SYM_L_GLOBAL)
	ANNOTATE_NOENDBR

	/* Construct struct pt_regs on stack */
	pushq	$__USER_DS		/* pt_regs->ss */
	pushq	%r8			/* pt_regs->sp */
	pushq	%r11			/* pt_regs->flags */
	pushq	$__USER32_CS		/* pt_regs->cs */
	pushq	%rcx			/* pt_regs->ip */
SYM_INNER_LABEL(entry_SYSCALL_compat_after_hwframe, SYM_L_GLOBAL)
	movl	%eax, %eax		/* discard orig_ax high bits */
	pushq	%rax			/* pt_regs->orig_ax */
	PUSH_AND_CLEAR_REGS rcx=%rbp rax=$-ENOSYS
	UNWIND_HINT_REGS

	IBRS_ENTER
	UNTRAIN_RET
	CLEAR_BRANCH_HISTORY

	movq	%rsp, %rdi
	call	do_fast_syscall_32
	/* XEN PV guests always use IRET path */
	ALTERNATIVE "testl %eax, %eax; jz swapgs_restore_regs_and_return_to_usermode", \
		    "jmp swapgs_restore_regs_and_return_to_usermode", X86_FEATURE_XENPV

	/* Opportunistic SYSRET */
sysret32_from_system_call:
	/*
	 * We are not going to return to userspace from the trampoline
	 * stack. So let's erase the thread stack right now.
	 */
	STACKLEAK_ERASE

	IBRS_EXIT

	movq	RBX(%rsp), %rbx		/* pt_regs->rbx */
	movq	RBP(%rsp), %rbp		/* pt_regs->rbp */
	movq	EFLAGS(%rsp), %r11	/* pt_regs->flags (in r11) */
	movq	RIP(%rsp), %rcx		/* pt_regs->ip (in rcx) */
	addq	$RAX, %rsp		/* Skip r8-r15 */
	popq	%rax			/* pt_regs->rax */
	popq	%rdx			/* Skip pt_regs->cx */
	popq	%rdx			/* pt_regs->dx */
	popq	%rsi			/* pt_regs->si */
	popq	%rdi			/* pt_regs->di */

        /*
         * USERGS_SYSRET32 does:
         *  GSBASE = user's GS base
         *  EIP = ECX
         *  RFLAGS = R11
         *  CS = __USER32_CS
         *  SS = __USER_DS
         *
	 * ECX will not match pt_regs->cx, but we're returning to a vDSO
	 * trampoline that will fix up RCX, so this is okay.
	 *
	 * R12-R15 are callee-saved, so they contain whatever was in them
	 * when the system call started, which is already known to user
	 * code.  We zero R8-R10 to avoid info leaks.
         */
	movq	RSP-ORIG_RAX(%rsp), %rsp
SYM_INNER_LABEL(entry_SYSRETL_compat_unsafe_stack, SYM_L_GLOBAL)
	ANNOTATE_NOENDBR

	/*
	 * The original userspace %rsp (RSP-ORIG_RAX(%rsp)) is stored
	 * on the process stack which is not mapped to userspace and
	 * not readable after we SWITCH_TO_USER_CR3.  Delay the CR3
	 * switch until after after the last reference to the process
	 * stack.
	 *
	 * %r8/%r9 are zeroed before the sysret, thus safe to clobber.
	 */
	SWITCH_TO_USER_CR3_NOSTACK scratch_reg=%r8 scratch_reg2=%r9

	xorl	%r8d, %r8d
	xorl	%r9d, %r9d
	xorl	%r10d, %r10d
	swapgs
	CLEAR_CPU_BUFFERS
	sysretl
SYM_INNER_LABEL(entry_SYSRETL_compat_end, SYM_L_GLOBAL)
	ANNOTATE_NOENDBR
	int3
SYM_CODE_END(entry_SYSCALL_compat)

/*
 * int 0x80 is used by 32 bit mode as a system call entry. Normally idt entries
 * point to C routines, however since this is a system call interface the branch
 * history needs to be scrubbed to protect against BHI attacks, and that
 * scrubbing needs to take place in assembly code prior to entering any C
 * routines.
 */
SYM_CODE_START(int80_emulation)
	ANNOTATE_NOENDBR
	UNWIND_HINT_FUNC
	CLEAR_BRANCH_HISTORY
	jmp do_int80_emulation
SYM_CODE_END(int80_emulation)