link_monitor

Implementing Link Monitoring

Introduction

The objective of this exercise is to write a P4 program that enables a host to monitor the utilization of all links in the network. This exercise builds upon the basic IPv4 forwarding exercise so be sure to complete that one before attempting this one. Specifically, we will modify the basic P4 program to process a source routed probe packet such that it is able to pick up the egress link utilization at each hop and deliver it to a host for monitoring purposes.

Our probe packet will contain the following three header types:

// Top-level probe header, indicates how many hops this probe
// packet has traversed so far.
header probe_t {
    bit<8> hop_cnt;
}

// The data added to the probe by each switch at each hop.
header probe_data_t {
    bit<1>    bos;
    bit<7>    swid;
    bit<8>    port;
    bit<32>   byte_cnt;
    time_t    last_time;
    time_t    cur_time;
}

// Indicates the egress port the switch should send this probe
// packet out of. There is one of these headers for each hop.
header probe_fwd_t {
    bit<8>   egress_spec;
}

We will use the pod-topology for this exercise, which consists of four hosts connected to four switches that are wired up as they would be in a single pod of a fat tree topology.

In order to monitor the link utilization our switch will maintain two register arrays:

• byte_cnt_reg - counts the number of bytes transmitted out of each port since the last probe packet was transmitted out of the port.
• last_time_reg - stores the last time that a probe packet was transmitted out of each port.

Our P4 program will be written for the V1Model architecture implemented on P4.org's bmv2 software switch. The architecture file for the V1Model can be found at: /usr/local/share/p4c/p4include/v1model.p4. This file desribes the interfaces of the P4 programmable elements in the architecture, the supported externs, as well as the architecture's standard metadata fields. We encourage you to take a look at it.

Spoiler alert: There is a reference solution in the solution sub-directory. Feel free to compare your implementation to the reference.

Step 1: Run the (incomplete) starter code

The directory with this README contains a skeleton P4 program, link_monitor.p4, which implements basic IPv4 forwarding, as well as source routing of the probe packets. Your job will be to extend this skeleton program to fill out the fields in the probe packet.

Before that, let's compile and test the incomplete link_monitor.p4 program:

1. In your shell, run:

   make run

   This will:

   • compile link_monitor.p4, and
   • start the pod-topo in Mininet and configure all switches with the link_monitor.p4 program + table entries, and
   • configure all hosts with the commands listed in pod-topo/topology.json

2. You should now see a Mininet command prompt. Open two terminals on h1:

   mininet> xterm h1 h1

3. In one of the xterms run the send.py script to start sending probe packets every second. Each of these probe packets takes the path indicated in link-monitor-topo.png.

   ./send.py

4. In the other terminal run the receive.py script to start receiving and parsing the probe packets. This allows us to monitor the link utilization within the network.

   ./receive.py

The reported link utilization and the switch port numbers will always be 0 because the probe fields have not been filled out yet.

5. Run an iperf flow between h1 and h4:

   mininet> iperf h1 h4

6. Type exit to leave each xterm and the Mininet command line. Then, to stop mininet:

   make stop

   And to delete all pcaps, build files, and logs:

   make clean

The measured link utilizations will not agree with what iperf reports because the probe packet fields have not been populated yet. Your goal is to fill out the probe packet fields so that the two measurements agree.

A note about the control plane

A P4 program defines a packet-processing pipeline, but the rules within each table are inserted by the control plane. When a rule matches a packet, its action is invoked with parameters supplied by the control plane as part of the rule.

In this exercise, we have already implemented the control plane logic for you. As part of bringing up the Mininet instance, the make run command will install packet-processing rules in the tables of each switch. These are defined in the sX-runtime.json files, where X corresponds to the switch number.

Important: We use P4Runtime to install the control plane rules. The content of files sX-runtime.json refer to specific names of tables, keys, and actions, as defined in the P4Info file produced by the compiler (look for the file build/link_monitor.p4.p4info.txt after executing make run). Any changes in the P4 program that add or rename tables, keys, or actions will need to be reflected in these sX-runtime.json files.

Step 2: Implement Link Monitoring Logic

The link_monitor.p4 file contains a skeleton P4 program with key pieces of logic replaced by TODO comments. Your implementation should follow the structure given in this file---replace each TODO with logic implementing the missing piece.

Here are a few more details about the design:

Parser

• The parser has been extended support parsing of the source routed probe packets. The parser is the most complicated part of the design so spend a bit of time reading over it. Note that it does not contain any TODO comments so there is nothing you need to change here.
• To parse the probe packets, we use the hdr.probe.hop_cnt to determine how many hops the packet has traversed prior to reaching the switch. If this is the first hop then there will not be any probe_data in the packet so we skip that state and transition directly to the parse_probe_fwd state. In the parse_probe_fwd state, we use the hdr.probe.hop_cnt field to figure out which egress_spec header field to use to perform forwarding and we save that port value into a metadata field which is subsequently used to perform forwarding.

Ingress Control

• The ingress control block looks very similar to the basic exercise. The only difference is that the apply block contains another condition to forward probe packets using the egress_spec field extracted by the parser. It also increments the hdr.probe.hop_cnt field.

Egress Control

• This is where the interesting stateful processing occurs. It uses the byte_cnt_reg register to count the number of bytes that have passed through each port since the last probe packet passed through the port.
• It adds a new probe_data header to the packet and filld out the bos (bottom of stack) field, as well as the swid (switch ID) field.
• TODO: your job is to fill out the rest of the probe packet fields in order to ensure that you can properly measure link utilization.

Deparser

• Simply emits all headers in the correct order.
• Note that emitting a header stack will only emit the headers within the stack that are actually marked as valid.

Step 3: Run your solution

Follow the instructions from Step 1. This time, the measured link utilizations should agree with what iperf reports.

Troubleshooting

There are several problems that might manifest as you develop your program:

1. link_monitor.p4 might fail to compile. In this case, make run will report the error emitted from the compiler and halt.

2. link_monitor.p4 might compile but fail to support the control plane rules in the s1-runtime.json through s4-runtime.json files that make run tries to install using P4Runtime. In this case, make run will report errors if control plane rules cannot be installed. Use these error messages to fix your link_monitor.p4 implementation.

3. link_monitor.p4 might compile, and the control plane rules might be installed, but the switch might not process packets in the desired way. The logs/sX.log files contain detailed logs that describing how each switch processes each packet. The output is detailed and can help pinpoint logic errors in your implementation.

Cleaning up Mininet

In the latter two cases above, make run may leave a Mininet instance running in the background. Use the following command to clean up these instances:

make stop

Food For Thought

Now that you've implemented this basic monitoring framework can you think of ways to leverage this information about link utilization within the core of the network? For instance, how might you use this data, either at the hosts or at the switches, to make real-time load-balancing decisions?