Skip to content

electricimp/LIS3DH

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

LIS3DH 3.0.0

The LIS3DH is a three-axis MEMS accelerometer. The LIS3DH application note can be found here. This sensor has extensive functionality and this class has not yet implemented all of it. The LIS3DH can interface over I²C or SPI; this library addresses only I²C.

All interrupt functions in the current library are configured for interrupt 1 only. There is no support for settings or control on interrupt 2.

This library also supports the LIS2DH12, another widely used three-axis MEMS accelerometer and which can be found on Electric Imp’s impExplorer™ Kit.

To include this library in your project, add #require "LIS3DH.device.lib.nut:3.0.0" at the top of your device code

Build Status

Class Usage

Constructor: LIS3DH(i2cBus[, i2cAddress])

The class’ constructor takes one required parameter (a configured imp I²C bus) and an optional parameter (the I²C address of the accelerometer). The I²C address must be the address of your sensor or an I²C error will be thrown.

Parameters

Parameter Type Required? Description
i2cBus hardware.i2c Yes A pre-configured I²C bus
i2cAddress byte No The I²C address of the accelerometer. Default: 0x30
#require "LIS3DH.device.lib.nut:3.0.0"

i2c <- hardware.i2c89;
i2c.configure(CLOCK_SPEED_400_KHZ);

// Use a non-default I2C address (SA0 pulled high)
accel <- LIS3DH(i2c, 0x32);

Class Methods

reset()

This method resets all control and interrupt registers to datasheet default values. This method need only be called to restore registers to these default conditions.

Return Value

Nothing.

Example

accel.reset();

setDataRate(rateInHz)

This method sets the Output Data Rate (ODR) of the accelerometer in Hertz. Supported data rates are 0 (Shutdown), 1, 10, 25, 50, 100, 200, 400, 1250 (Normal Mode only), 1600 (Low-Power Mode only) and 5000 (Low-Power Mode only). The requested data rate will be rounded up to the closest supported rate and the actual data rate will be returned.

The default data rate is 0 (Shutdown). To take a reading with getAccel() you must set a data rate greater than 0.

Parameters

Parameter Type Required? Description
rateInHz Integer Yes The required Output Data Rate (ODR) of the accelerometer in Hertz

Return Value

Integer — the actual data rate.

Example

local rate = accel.setDataRate(90);
server.log(format("Accelerometer running at %dHz", rate));
// Displays 'Accelerometer running at 100Hz'

setMode(mode)

This method sets the accelerometer into low power, normal or high resolution mode. The method takes one of three mode constants: LIS3DH_MODE_NORMAL, LIS3DH_MODE_LOW_POWER or LIS3DH_MODE_HIGH_RESOLUTION. The default mode is LIS3DH_MODE_NORMAL.

Parameters

Parameter Type Required? Description
mode Integer Yes The required accelerometer mode

Return Value

Nothing.

Example

accel.setMode(LIS3DH_MODE_HIGH_RESOLUTION);

enable([state])

This method enables or disables all three axes on the accelerometer. Calling the method without an argument enables the accelerometer. When state is false, the accelerometer will be disabled.

Parameters

Parameter Type Required? Description
state Boolean No Activate (true) or disable (false) the accelerometer. Default: true

Return Value

Nothing.

Example

function goToSleep() {
    imp.onidle(function() {
        // Set data rate to 0 and disable the accelerometer to save power
        accel.setDataRate(0);
        accel.enable(false);

        // Sleep for 1 hour
        server.sleepfor(3600);
    });
}

getAccel([callback])

This method reads the latest measurement from the accelerometer. It takes an optional callback for asynchronous operation — it will block otherwise. The callback should take one parameter: a results table (see below). If the callback is null or omitted, the method will return the results table.

Parameters

Parameter Type Required? Description
callback Function No Function called with the accelerometer reading as its only argument. The reading is a table as described in Return Value, below

Return Value

Table — The latest reading from the accelerometer as a table with slots x, y and z, or just error if an I²C error was encountered. Note if getAccel() is called with an argument, it will return nothing.

Synchronous Example

accel.setDataRate(100);
local reading = accel.getAccel();
if ("error" in reading) {
    server.error(reading.error);
} else {
    server.log(format("Acceleration (G): (%0.2f, %0.2f, %0.2f)", reading.x, reading.y, reading.z));
}

Asynchronous Example

accel.setDataRate(100);
accel.getAccel(function(reading) {
    if ("error" in reading) {
        server.error(reading.error);
    } else {
        server.log(format("Acceleration (G): (%0.2f, %0.2f, %0.2f)", reading.x, reading.y, reading.z));
    }
});

setRange(range)

This method sets the measurement range of the sensor in Gs. Supported ranges are ±2, ±4, ±8 and ±16G. The data rate will be rounded up to the closest supported range and the actual range will be returned. The default measurement range is ±2G.

Parameters

Parameter Type Required? Description
range Integer Yes The measurement range of the sensor in Gs

Return Value

Integer — the current measurement range.

Example

// Set sensor range to +/- 8G
local range = accel.setRange(8);
server.log(format("Range set to +/- %dG", range));

getRange()

This method returns the currently-set measurement range of the sensor in Gs.

Return Value

Integer — the current measurement range.

server.log(format("Current Sensor Range is +/- %dG", accel.getRange()));

enableADC(state)

This method enables the three ADC lines available to the LIS3DH (the LIS2DH does not have these auxiliary lines available). Its input ranges from approximately 0.8-1.6V. By default, the ADC is disabled.

Parameters

Parameter Type Required? Description
state Boolean Yes Sets the ADC on (true) or off (false)

Return Value

Nothing.

Example

accel.enableADC(true);

readADC(line)

This method returns a reading from approximately 0.8-1.6V from the specified ADC line. The required line, one of three, is set by providing one the following constants: LIS3DH_ADC1, LIS3DH_ADC2 or LIS3DH_ADC3. The ADC must first be enabled by calling enableADC(true).

Parameters

Parameter Type Required? Description
line Integer Yes The ADC line

Return Value

Float — the reading from the selected ADC line.

Example

accel.enableADC(true);
local reading = accel.readADC(LIS3DH_ADC1);

getDeviceId()

This method returns the one-byte device ID of the sensor (from the WHO_AM_I register). The getDeviceId() method is a simple way to test if your LIS3DH sensor is correctly connected.

Return Value

Integer — single-byte device ID.

Example

server.log(format("Device ID: 0x%02X", accel.getDeviceId()));

configureHighPassFilter(filters[, cutoff][, mode])

This method configures the high-pass filter.

Parameters

Parameter Type Required? Description
filters Integer Yes Select the filter(s) to enable/disable by OR-ing together any of the constants found under Filters, below
cutoff Integer No See High-pass Filter Cut-off Frequencies, below. Default: LIS3DH_HPF_CUTOFF1
mode Integer No See Modes, below. Default: LIS3DH_HPF_DEFAULT_MODE

Filters

Filter Constant Description
LIS3DH_HPF_AOI_INT1 High-pass filter enabled for AOI function on interrupt 1
LIS3DH_HPF_AOI_INT2 High-pass filter enabled for AOI function on interrupt 2
LIS3DH_HPF_CLICK High-pass filter enabled for CLICK function
LIS3DH_HPF_FDS Filtered data selection. Enables data from internal filter sent to output register and FIFO
LIS3DH_HPF_DISABLED Disables all filters

High-pass Filter Cut-off Frequencies

Cut-off Constant f@1Hz f@10Hz f@25Hz f@50Hz f@100Hz f@200Hz f@400Hz f@1600Hz f@5000Hz
LIS3DH_HPF_CUTOFF1 0.02 0.2 0.5 1 2 4 8 32 100
LIS3DH_HPF_CUTOFF2 0.008 0.08 0.2 0.5 1 2 4 16 50
LIS3DH_HPF_CUTOFF3 0.004 0.04 0.1 0.2 0.5 1 2 8 25
LIS3DH_HPF_CUTOFF4 0.002 0.02 0.05 0.1 0.2 0.5 1 4 12

Modes

Mode Constant Description
LIS3DH_HPF_DEFAULT_MODE Normal mode (reset reading HP_RESET_FILTER)
LIS3DH_HPF_REFERENCE_SIGNAL Reference signal for filtering
LIS3DH_HPF_NORMAL_MODE Normal mode
LIS3DH_HPF_AUTORESET_ON_INTERRUPT Autoreset on interrupt event

Return Value

Nothing.

Example

// Enable high-pass filter on click and inertial interrupt 1 with auto reset on interrupt event
accel.configureHighPassFilter(LIS3DH_HPF_AOI_INT1 | LIS3DH_HPF_CLICK,
                              null,
                              LIS3DH_HPF_AUTORESET_ON_INTERRUPT);

// Disable high pass filter
accel.configureHighPassFilter(LIS3DH_HPF_DISABLED);

configureFifo(enableBuffer[, mode])

This method enables/disables the FIFO buffer and configures its mode.

Parameters

Parameter Type Required? Description
enableBuffer Boolean Yes Whether to enable (true) or disable (false) the Fifo buffer
mode Bitfield No See FIFO Modes, below. Default: LIS3DH_FIFO_STREAM_MODE

FIFO Modes

Mode Description
LIS3DH_FIFO_BYPASS_MODE Disables the FIFO buffer (only the first address is used for each channel)
LIS3DH_FIFO_FIFO_MODE When full, the FIFO buffer stops collecting data from the input channels
LIS3DH_FIFO_STREAM_MODE When full, the FIFO buffer discards the older data as the new arrive
LIS3DH_FIFO_STREAM_TO_FIFO_MODE When full, the FIFO buffer discards the older data as the new arrive. Once trigger event occurs, the FIFO buffer starts operating in FIFO mode

Return Value

Nothing.

Example

// Enable the FIFO buffer in LIS3DH_FIFO_STREAM_TO_FIFO_MODE
accel.configureFifo(true, LIS3DH_FIFO_STREAM_TO_FIFO_MODE);

configureFifoInterrupts(enableWatermark[, enableOverrun][, watermark])

This method enables/disables FIFO watermark and overrun interrupts. Please note the FIFO buffer must be enabled for the interrupt to work properly.

Parameters

Parameter Type Required? Description
enableWatermark Boolean Yes Whether to enable (true) or disable (false) the FIFO watermark interrupt
enableOverrun Boolean No Whether to enable (true) or disable (false) the FIFO overrun interrupt Default: false
watermark Integer No Number of buffer slots filled to generate interrupt. Buffer has 32 slots. Default: 29

Example

// Configure the FIFO buffer in Stream Mode and set interrupt generator
// to generate an interrupt when there are 30 entries in the buffer
accel.configureFifo(true);
accel.configureFifoInterrupts(true, false, 30);

getFifoStats()

This method returns information about the state of the FIFO buffer.

Return Value

Table — the FIFO buffer state:

Key Type Description
watermark Boolean true if watermark has been set
overrun Boolean true if data has been overwritten without being read
empty Boolean true if buffer is empty
unread Integer Number of unread slots in buffer

Example

local fifoStatus = accel.getFifoStats();
local numUnreadReadings = fifoStatus.unread;
for (local i = 0; i < numUnreadReadings; i++) {
    local reading = accel.getAccel();
    server.log(format("Accel (x,y,z): [%d, %d, %d]", data.x, data.y, data.z));
}

configureInterruptLatching(state)

Enables (state is true) or disables (state is false) interrupt latching. If interrupt latching is enabled, the interrupt signal will remain asserted until the interrupt source register is read by calling getInterruptTable(). If latching is disabled, the interrupt signal will remain asserted as long as the interrupt-generating condition persists.

Interrupt latching is disabled by default.

Parameters

Parameter Type Required? Description
state Boolean Yes The latching state: true to enable, false to disable

Return Value

Nothing.

Example

// Configure interrupt pin to latch
accel.configureInterruptLatching(true);

configureInertialInterrupt(state[, threshold][, duration][, options])

This method configures the inertial interrupt generator.

Parameters

Parameter Type Required? Description
state Boolean Yes The interrupt state: true to enable, false to disable
threshold Float No Inertial interrupts threshold in Gs. Default: 2.0
duration Integer No Number of samples exceeding threshold required to generate interrupt. Default: 5
options Bitfield No See Option Flags, below. Default: LIS3DH_X_HIGH | LIS3DH_Y_HIGH | LIS3DH_Z_HIGH)

The default configuration for the Inertial Interrupt generator is to generate an interrupt when the acceleration on any axis exceeds 2G. This behavior can be changed by OR-ing together any of the following flags:

Option Flags

Flag Description
LIS3DH_X_LOW Generates an interrupt when the x-axis acceleration goes below the threshold
LIS3DH_X_HIGH Generates an interrupt when the x-axis acceleration goes above the threshold
LIS3DH_Y_LOW Generates an interrupt when the y-axis acceleration goes below the threshold
LIS3DH_Y_HIGH Generates an interrupt when the y-axis acceleration goes above the threshold
LIS3DH_Z_LOW Generates an interrupt when the z-axis acceleration goes below the threshold
LIS3DH_Z_HIGH Generates an interrupt when the z-axis acceleration goes above the threshold
LIS3DH_AOI Sets the AOI flag (see Inertial Interrupt Modes, below)
LIS3DH_SIX_D Sets the 6D flag (see Inertial Interrupt Modes, below)

Inertial Interrupt Modes

The following is taken from the from LIS3DH Datasheet (section 8.21):

AOI 6D Interrupt Mode
0 0 OR combination of interrupt events
0 1 6-direction movement recognition
1 0 AND combination of events
1 1 6-direction position recognition

Movement Recognition (01) An interrupt is generate when orientation move from unknown zone to known zone. The interrupt signal stay for a duration ODR.

Direction Recognition (11) An interrupt is generate when orientation is inside a known zone. The interrupt signal stay until orientation is inside the zone.

Return Value

Nothing.

Example

// Configure the Inertial interrupt generator to generate an interrupt
// when acceleration on all three exceeds 1G.
accel.configureInertialInterrupt(true, 1.0, 10, LIS3DH_X_LOW | LIS3DH_Y_LOW | LIS3DH_Z_LOW | LIS3DH_AOI)

configureFreeFallInterrupt(state[, threshold][, duration])

This method configures the inertial interrupt generator to generate interrupts when the device is in free fall, ie. acceleration on all axis approaches 0.

Note This method will overwrite any settings configured with configureInertialInterrupt().

Parameters

Parameter Type Required? Description
state Boolean Yes The interrupt state: true to enable, false to disable
threshold Float No Inertial interrupts threshold in Gs. Default: 0.5
duration Integer No Number of samples exceeding threshold required to generate interrupt. Default: 5

Return Value

Nothing.

Example

accel.configureFreeFallInterrupt(true);

configureClickInterrupt(state[, clickType][, threshold][, timeLimit][, latency][, window])

This method configures the click interrupt generator.

Parameters

Parameter Type Required? Description
state Boolean Yes The interrupt state: true to enable, false to disable
clickType Integer No LIS3DH_SINGLE_CLICK or LIS3DH_DOUBLE_CLICK. Default: LIS3DH_SINGLE_CLICK
threshold Float No Inertial interrupts threshold in Gs. Default: 1.1
timeLimit Float No Maximum time in milliseconds the acceleration can spend above the threshold to be considered a click. Default: 5
latency Float No Minimum time in milliseconds between the end of one click event and the start of another to be considered a LIS3DH_DOUBLE_CLICK. Default: 10
window Float o Maximum time in milliseconds between the start of one click event and end of another to be considered a LIS3DH_DOUBLE_CLICK. Default: 50

Return Value

Nothing.

Single Click Example

// Configure a single click interrupt
accel.configureClickInterrupt(true, LIS3DH_SINGLE_CLICK);

Double Click Example

// configure a double click interrupt
accel.configureClickInterrupt(true, LIS3DH_DOUBLE_CLICK);

configureDataReadyInterrupt(state)

This method enables (state is true) or disables (state is false) data-ready interrupts on the sensor’s INT1 line. The data-ready signal rises to 1 when a new set of acceleration data has been generated and it is available for reading. The interrupt is reset when the higher part of the data of all the enabled channels has been read.

Parameters

Parameter Type Required? Description
state Boolean Yes The interrupt state: true to enable, false to disable

Return Value

Nothing.

Example

accel.setDataRate(1); // 1Hz
accel.configureDataReadyInterrupt(true);

getInterruptTable()

This method reads the LIS3DH’s INT1_SRC and CLICK_SRC registers.

Return Value

Table — the interrupt settings:

Key Type Description
int1 Bool true if INT1 created the interrupt
xLow Bool true if a xLow condition is present
yLow Bool true if a yLow condition is present
zLow Bool true if a zLow condition is present
xHigh Bool true if a xHigh condition is present
yHigh Bool true if a yHigh condition is present
zHigh Bool true if a zHigh condition is present
click Bool true if any click created the interrupt
singleClick Bool true if a single click created the interrupt
doubleClick Bool true if a double click created the interrupt

Example

local result = accel.getInterruptTable();
if (result.int1) server.log("Interrupt was triggered");

License

This library is licensed under the MIT License.