net: Add dm9051 driver

v1-v4

Add davicom dm9051 spi ethernet driver. The driver work for the
device platform with spi master

Test ok with raspberry pi 2 and pi 4, the spi configure used in
my raspberry pi 4 is spi0.1, spi speed 31200000, and INT by pin 26.

v5

Work to eliminate the wrappers to be clear for read, swapped to
phylib for phy connection tasks.

Tested with raspberry pi 4. Test for netwroking function, CAT5
cable unplug/plug and also ethtool detect for link state, and
all are ok.

v6

remove the redundant code that phylib has support,
adjust to be the reasonable sequence,
fine tune comments, add comments for pause function support

Tested with raspberry pi 4. Test for netwroking function, CAT5
cable unplug/plug and also ethtool detect for link state, and
all are ok.

v7

read/write registers must return error code to the callet,
add to enable pause processing

v8

not parmanently set MAC by .ndo_set_mac_address

correct rx function such as clear ISR,
inblk avoid stack buffer,
simple skb buffer process and
easy use netif_rx_ni.

simplely queue init and wake the queues,
limit the start_xmit function use netif_stop_queue.

descript that schedule delay is essential
for tx_work and rxctrl_work

eliminate ____cacheline_aligned and
add static int msg_enable.

v9

use phylib, no need 'select MII' in Kconfig,
make it clear in dm9051_xfer when using spi_sync,
improve the registers read/write so that error code
return as far as possible up the call stack.

v10

use regmap APIs for SPI and MDIO,
modify to correcting such as include header files
and program check styles

Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Joseph CHAMG <josright123@gmail.com>

drivers/net/ethernet/davicom/Kconfig

@@ -3,6 +3,19 @@
 # Davicom device configuration
 #
 
+config NET_VENDOR_DAVICOM
+	bool "Davicom devices"
+	default y
+	help
+	  If you have a network (Ethernet) card belonging to this class, say Y.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Davicom devices. If you say Y, you will be asked
+	  for your specific card in the following selections.
+
+if NET_VENDOR_DAVICOM
+
 config DM9000
 	tristate "DM9000 support"
 	depends on ARM || MIPS || COLDFIRE || NIOS2 || COMPILE_TEST
@@ -22,3 +35,19 @@ config DM9000_FORCE_SIMPLE_PHY_POLL
 	  bit to determine if the link is up or down instead of the more
 	  costly MII PHY reads. Note, this will not work if the chip is
 	  operating with an external PHY.
+
+config DM9051
+	tristate "DM9051 SPI support"
+	select PHYLIB
+	depends on SPI
+	select CRC32
+	help
+	  Support for DM9051 SPI chipset.
+
+	  To compile this driver as a module, choose M here.  The module
+	  will be called dm9051.
+
+	  The SPI mode for the host's SPI master to access DM9051 is mode
+	  0 on the SPI bus.
+
+endif # NET_VENDOR_DAVICOM

drivers/net/ethernet/davicom/Makefile

@@ -4,3 +4,4 @@
 #
 
 obj-$(CONFIG_DM9000) += dm9000.o
+obj-$(CONFIG_DM9051) += dm9051.o