The Salad Fork is a Voron Trident scaled down to use 1515 aluminum extrusions for the frame instead of 2020, exactly like how the Micron is a Voron 2.4 scaled down. It is not a modification for a Voron V0, but a from-scratch build that requires longer extrusions and rails, two more V0.1 integrated-leadscrew Z motors, a higher-wattage power supply, possibly a bigger bed…
Why go to the trouble of a whole new build? Well, Salad Fork features:
- Support for build volumes of 120mm³ or 150mm³ (1.95× the build volume of a V0.1!)
- Klicky support
- Purge bucket support
Coming soon™…
- Sexbolt support
- Magnetically-attached panels
The latest official BOM is available on Google Sheets. The information below may not be complete; last updated November 17, 2021.
Frame (120mm³ build volume)
Component | Quantity | Notes |
---|---|---|
HFS3-1515-400 | 4 | Cross-drill 7.5mm from both ends, plus drill 1× gantry hole each per drill guide |
HFS3-1515-270 | 6 | Tap both ends |
HFS3-1515-240 | 5 | Tap both ends, cross-drill 2 extrusions at center |
HFS3-1515-230 | 1 | Tap one end |
HFS3-1515-210 | 1 | |
HFS3-1515-145 | 1 | |
HFS3-1515-140 | 1 | Tap one end |
Frame (150mm³ build volume)
Component | Quantity | Notes |
---|---|---|
HFS3-1515-400 | 4 | Cross-drill 7.5mm from both ends, plus drill 1× gantry hole each per drill guide |
HFS3-1515-300 | 6 | Tap both ends |
HFS3-1515-270 | 5 | Tap both ends, cross-drill 2 extrusions at center |
HSF3-1515-240 | 1 | Tap one end |
HSF3-1515-230 | 1 | |
HFS3-1515-175 | 1 | |
HSF3-1515-170 | 1 | Tap one end |
Fasteners
Component | Quantity |
---|---|
M2x6 BHCS | 24 |
M2x10 self-tapping | 4 |
M2x12 SHCS | 8 |
M3x6 BHCS | 49 |
M3x6 SHCS | 10 |
M3x8 BHCS | 41 |
M3x8 SHCS | 8 |
M3x10 BHCS | 40 |
M3x12 BHCS | 4 |
M3x12 SHCS | 18 |
M3x16 SHCS | 3 |
M3x20 SHCS | 6 |
M3x25 BHCS | 18 |
M3x25 SHCS | 6 |
M3x30 BHCS | 2 |
M3x35 BHCS | 5 |
M3x35 SHCS | 4 |
M5x16 BHCS | 3 |
M3 Heatset | 30 |
M3 Washer | 26 |
M3 lock nut | 6 |
M3 hex nut | 98 |
M4 knurled nut | 3 |
M5 hex nut | 3 |
6x3 neodymium magnet | 8 |
Motion
Component | Quantity |
---|---|
NEMA14 stepper | 2 |
NEMA17 integrated-leadscrew stepper | 3 |
MGN9C 180 | 1 (for 120mm³) |
MGN7H 200 | 5 (for 120mm³) |
MGN9C 210 | 1 (for 150mm³) |
MGN7H 230 | 2 (for 150mm³) |
MGN7H 200 | 3 (for 150mm³) |
Gates GT2 6mm open belt | 4m |
F623-RS flanged bearings | 24 |
GE5C spherical bearings | 3 |
D2F switch | 4 |
TR8×8 leadscrew nut | 3 |
Rubber foot | 4 |
Electronics
Component | Quantity | Notes |
---|---|---|
Control board | 1 | Fysetc Spider or BigTreeTech Octopus |
TMC 2209 driver | 6 | |
Raspberry Pi | 1 | The Klipper host |
C13 power cable | 1 | |
Meanwell UHP-200-24 | 1 | |
Keenovo 100mm² 60W 24V heater | 1 | DC bed heater, 120mm³ build |
Keenovo 120mm² 120W 24V heater | 1 | DC bed heater, 150mm³ build |
Keenovo 100mm² 60W 120/240V heater | 1 | AC bed heater, 120mm³ build |
Keenovo 120mm² 120W 120/240V heater | 1 | AC bed heater, 150mm³ build |
AC SSR (Omron G3NA-210B-UTU DC5-24, Panasonic AQA211VL) | 1 | for AC bed heater |
Toolhead
Component | Quantity | Notes |
---|---|---|
NEMA14 pancake stepper | 1 | |
BMG gear set | 1 | |
3010 axial fan | 1 | Only for Dragonfly BMS hotend |
3007 axial fan | 1 | All other hotends |
3010 blower fan | 2 | |
Hotend | 1 |