Home Assistant integration to read Values from C.M.I

This integration monitors the inputs and outputs of the devices connected to a C.M.I. from Technische Alternative. It creates a separate (binary) sensor for each input and output which displays the current values.

The data is fetched every 10 minutes.

Currently supported devices:

• UVR1611
• UVR16x2
• RSM610
• CAN-I/O45
• CAN-EZ2
• CAN-MTx2
• CAN-BC2
• UVR65
• CAN-EZ3
• UVR610
• UVR67

Note The loading time of the integration is extended by one minute per configured node on the C.M.I. to avoid triggering the rate limit. The same applies to the setup process

{% if not installed %}

Installation

Step 1:

Step 2 (Don't forget):

1. Click install.
2. In the HA UI go to "Configuration" -> "Integrations" click "+" and search for "Technische Alternative".
3. Start the config flow.

{% endif %}

Step 3:

Note When saving the configuration, there may be a wait time due to the rate limit.

C.M.I. configuration

In the first step of the config flow, set up the connection to C.M.I.. To do this, enter the address, user name and password.

Device selection

In the 2nd step, select the devices from which the data is to be read. For this purpose, a list of all devices and details about them are retrieved at the start of the step. This can take several minutes due to a rate limit of one request per minute. Once the data has been retrieved, select the supported devices from the list.

If to configure the channels individually, continue with the next step, otherwise the setup is finished.

Channel configuration

In this step, individual channels can be customized, including the following properties:

• Name of the sensor (can also be changed to HA afterward)
• Device class

To customize a channel, select the device, on which the channel is located, enter the channel number and finally select the channel type.

Supported data types

Device type	Inputs	Outputs	DL-inputs	System-values: General	System-values: Date	System-values: Time	System-values: Sun	System-values: Electrical power	Analog network inputs	Digital network inputs	M-Bus	Modbus	KNX	Analog logging	Digital logging
UVR1611	✔	✔	❌	❌	❌	❌	❌	❌	✔	✔	❌	❌	❌	❌	❌
UVR16x2	✔	✔	✔	✔	✔	✔	✔	❌	❌	❌	❌	❌	❌	✔	✔
RSM610	✔	✔	✔	❌	❌	❌	❌	❌	❌	❌	✔	❌	❌	❌	❌
CAN-I/O45	✔	✔	✔	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌
CAN-EZ2	✔	✔	❌	❌	❌	❌	❌	✔	❌	❌	❌	❌	❌	❌	❌
CAN-MTx2	✔	✔	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌
CAN-BC2	✔	✔	❌	❌	❌	❌	❌	❌	❌	❌	✔	✔	✔	❌	❌
UVR65	✔	✔	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌
CAN-EZ3	❌	❌	✔	✔	✔	✔	✔	✔	❌	❌	❌	✔	❌	✔	✔
UVR610	✔	✔	✔	❌	❌	❌	❌	❌	❌	❌	✔	❌	❌	❌	❌
UVR67	✔	✔	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌	❌

Note The supported data types may differ from the official API. If a device type supports other data types than listed here, please create an issue.