80 add option for netcdf infiltration quadtree file input #81
Conversation
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
…ssYes" - Also in Makefile.am
…f90 within one subroutine "read_infiltration_file_original". - Division between original/netcdf input same as for subgrid
- In sfincs_domain read either read_infiltration_file_original or read_infiltration_file_netcdf, and check whether combinations match - We use _original only for regular grid, and _netcdf only for quadtree grid
…ile with input qinffield/scs_se/ksfield assuming inftype = 'cnb' - Reading and remapping was tested for quadtree_msk
- Note ; had to change definition of gamma, so not anymore mean gamma over current and upwind point > changes gamma and thus source term and IG growth, have to check still whether that is a problem or not - todo: clean up
…t to 0 everytime snapwave_solver is called, so now determined again - Code can be cleaned up by doing a H inout definition probably
…vious ee' part - and result now only little bit different anymore, because of removal of previous loop now?
… as in paper - Thereby not using H_inc_old and H_ig_old anymore from wave heights of last time step (but implicitly we still do)
… it again at the start of solve_energy_balance2Dstat - Remove Sxx outside of subroutine 'solve_energy_balance2Dstat', since that is not needed anymore
… to determine Hig,0 from 10 m to 5 m
…ne 'determine_infragravity_source_sink_term' for clarity - Also makes it easier to experiment puting the source term determination in the ' do iter=1,niter '-loop
…ior to iteration loop, to fill 'srcsh', based on effectively incident energy from previous SnapWave timestep - Then depending on new option, 'snapwave_iterative_srcsh=1, is new default', the subroutine is called again to determine srcsh now based on just updated incident wave energy. - If nr_sweeps = 4, this is slower because subroutine 'determine_infragravity_source_sink_term' is called multiple times - But, Hm0 IG converges now immediately, instead of after a few timesteps! - However, to speed up you can with snapwave_iterative_srcsh = 0 still keep old behaviour of only using the initial filling of 'srcsh'. Depends on application whether slower convergence IG wave height is problem - TODO: check whether slower performance can still be counteracted some way
…inside the subroutine
- ! Update H(k), used in subroutine to calculate relative waterdepth 'gam' > TL: this creates a variability over sweeps/iterations/timesteps since 'gam' changes every time > seems more stable not to do this - OMP loop in solver did not seem to provide speedup - OMP loop in subroutine 'determine_infragravity_source_sink_term' made things slower - Even without these 3 attempts, performance loss of more times calling subroutine 'determine_infragravity_source_sink_term' in iteration loop seems negligible for small model
…g srcsh only for the first sweep (but still every iteration)
This reverts commit 04a8e61.
…estep we get already a good estimate of srcig and thereby Hig, and not just only conservative shoaling from the boundary - Only done once to prevent changing H(k) > and thereby gam and alphaig > every time, to prevent oscillations
- correct var names from quadtree infiltration netcdf file
- add needed 'if (nm>0) ' checks for quadtree max output
…m to m needed anymore
- fix debug mode issues with extra (nm > 0) checks
…imestep' into '80 add option for netcdf infiltration quadtree file input'
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
No description provided.