Merge tag 'v4.9.109' into 4.9-2.0.x-imx #27

gibsson · 2018-06-25T16:00:46Z

No description provided.

commit b5d0ebc upstream. The suspend/resume behavior of the TPM can be controlled by setting "powered-while-suspended" in the DTS. This is useful for the cases when hardware does not power-off the TPM. Signed-off-by: Sonny Rao <sonnyrao@chromium.org> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.l.morris@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0803d7b upstream. The Acer Acer Veriton X4110G has a TPM device detected as: tpm_tis 00:0b: 1.2 TPM (device-id 0xFE, rev-id 71) After the first S3 suspend, the following error appears during resume: tpm tpm0: A TPM error(38) occurred continue selftest Any following S3 suspend attempts will now fail with this error: tpm tpm0: Error (38) sending savestate before suspend PM: Device 00:0b failed to suspend: error 38 Error 38 is TPM_ERR_INVALID_POSTINIT which means the TPM is not in the correct state. This indicates that the platform BIOS is not sending the usual TPM_Startup command during S3 resume. >From this point onwards, all TPM commands will fail. The same issue was previously reported on Foxconn 6150BK8MC and Sony Vaio TX3. The platform behaviour seems broken here, but we should not break suspend/resume because of this. When the unexpected TPM state is encountered, set a flag to skip the affected TPM_SaveState command on later suspends. Cc: stable@vger.kernel.org Signed-off-by: Chris Chiu <chiu@endlessm.com> Signed-off-by: Daniel Drake <drake@endlessm.com> Link: http://lkml.kernel.org/r/CAB4CAwfSCvj1cudi+MWaB5g2Z67d9DwY1o475YOZD64ma23UiQ@mail.gmail.com Link: https://lkml.org/lkml/2011/3/28/192 Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=591031 Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit be83bbf upstream. The internal VM "mmap()" interfaces are based on the mmap target doing everything using page indexes rather than byte offsets, because traditionally (ie 32-bit) we had the situation that the byte offset didn't fit in a register. So while the mmap virtual address was limited by the word size of the architecture, the backing store was not. So we're basically passing "pgoff" around as a page index, in order to be able to describe backing store locations that are much bigger than the word size (think files larger than 4GB etc). But while this all makes a ton of sense conceptually, we've been dogged by various drivers that don't really understand this, and internally work with byte offsets, and then try to work with the page index by turning it into a byte offset with "pgoff << PAGE_SHIFT". Which obviously can overflow. Adding the size of the mapping to it to get the byte offset of the end of the backing store just exacerbates the problem, and if you then use this overflow-prone value to check various limits of your device driver mmap capability, you're just setting yourself up for problems. The correct thing for drivers to do is to do their limit math in page indices, the way the interface is designed. Because the generic mmap code _does_ test that the index doesn't overflow, since that's what the mmap code really cares about. HOWEVER. Finding and fixing various random drivers is a sisyphean task, so let's just see if we can just make the core mmap() code do the limiting for us. Realistically, the only "big" backing stores we need to care about are regular files and block devices, both of which are known to do this properly, and which have nice well-defined limits for how much data they can access. So let's special-case just those two known cases, and then limit other random mmap users to a backing store that still fits in "unsigned long". Realistically, that's not much of a limit at all on 64-bit, and on 32-bit architectures the only worry might be the GPU drivers, which can have big physical address spaces. To make it possible for drivers like that to say that they are 64-bit clean, this patch does repurpose the "FMODE_UNSIGNED_OFFSET" bit in the file flags to allow drivers to mark their file descriptors as safe in the full 64-bit mmap address space. [ The timing for doing this is less than optimal, and this should really go in a merge window. But realistically, this needs wide testing more than it needs anything else, and being main-line is the only way to do that. So the earlier the better, even if it's outside the proper development cycle - Linus ] Cc: Kees Cook <keescook@chromium.org> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Willy Tarreau <w@1wt.eu> Cc: Dave Airlie <airlied@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 423913a upstream. Commit be83bbf ("mmap: introduce sane default mmap limits") was introduced to catch problems in various ad-hoc character device drivers doing mmap and getting the size limits wrong. In the process, it used "known good" limits for the normal cases of mapping regular files and block device drivers. It turns out that the "s_maxbytes" limit was less "known good" than I thought. In particular, /proc doesn't set it, but exposes one regular file to mmap: /proc/vmcore. As a result, that file got limited to the default MAX_INT s_maxbytes value. This went unnoticed for a while, because apparently the only thing that needs it is the s390 kernel zfcpdump, but there might be other tools that use this too. Vasily suggested just changing s_maxbytes for all of /proc, which isn't wrong, but makes me nervous at this stage. So instead, just make the new mmap limit always be MAX_LFS_FILESIZE for regular files, which won't affect anything else. It wasn't the regular file case I was worried about. I'd really prefer for maxsize to have been per-inode, but that is not how things are today. Fixes: be83bbf ("mmap: introduce sane default mmap limits") Reported-by: Vasily Gorbik <gor@linux.ibm.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e2731e5 upstream. btrfs-progs uses super flag bit BTRFS_SUPER_FLAG_METADUMP_V2 (1ULL << 34). So just define that in kernel so that we know its been used. Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2ae89c7 upstream. In file included from scripts/kconfig/zconf.tab.c:2485: scripts/kconfig/confdata.c: In function ‘conf_write’: scripts/kconfig/confdata.c:773:22: warning: ‘%s’ directive writing likely 7 or more bytes into a region of size between 1 and 4097 [-Wformat-overflow=] sprintf(newname, "%s%s", dirname, basename); ^~ scripts/kconfig/confdata.c:773:19: note: assuming directive output of 7 bytes sprintf(newname, "%s%s", dirname, basename); ^~~~~~ scripts/kconfig/confdata.c:773:2: note: ‘sprintf’ output 1 or more bytes (assuming 4104) into a destination of size 4097 sprintf(newname, "%s%s", dirname, basename); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ scripts/kconfig/confdata.c:776:23: warning: ‘.tmpconfig.’ directive writing 11 bytes into a region of size between 1 and 4097 [-Wformat-overflow=] sprintf(tmpname, "%s.tmpconfig.%d", dirname, (int)getpid()); ^~~~~~~~~~~ scripts/kconfig/confdata.c:776:3: note: ‘sprintf’ output between 13 and 4119 bytes into a destination of size 4097 sprintf(tmpname, "%s.tmpconfig.%d", dirname, (int)getpid()); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Increase the size of tmpname and newname to make GCC happy. Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 76ef6b2 upstream. Since we have the ttm and gem vma managers using a subset of the file address space for objects, and these start at 0x100000000 they will overflow the new mmap checks. I've checked all the mmap routines I could see for any bad behaviour but overall most people use GEM/TTM VMA managers even the legacy drivers have a hashtable. Reported-and-Tested-by: Arthur Marsh (amarsh04 on #radeon) Fixes: be83bbf (mmap: introduce sane default mmap limits) Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit dd612f1 ] Nearby code that also tests port suggests that the P0 constant should be used when port is zero. The semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression e,e1; @@ * e ? e1 : e1 // </smpl> Fixes: 6c3218c ("bnx2x: Adjust ETS to 578xx") Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 2677d20 ] Syzbot reported the use-after-free in timer_is_static_object() [1]. This can happen because the structure for the rto timer (ccid2_hc_tx_sock) is removed in dccp_disconnect(), and ccid2_hc_tx_rto_expire() can be called after that. The report [1] is similar to the one in commit 120e9da ("dccp: defer ccid_hc_tx_delete() at dismantle time"). And the fix is the same, delay freeing ccid2_hc_tx_sock structure, so that it is freed in dccp_sk_destruct(). [1] ================================================================== BUG: KASAN: use-after-free in timer_is_static_object+0x80/0x90 kernel/time/timer.c:607 Read of size 8 at addr ffff8801bebb5118 by task syz-executor2/25299 CPU: 1 PID: 25299 Comm: syz-executor2 Not tainted 4.17.0-rc5+ Freescale#54 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1b9/0x294 lib/dump_stack.c:113 print_address_description+0x6c/0x20b mm/kasan/report.c:256 kasan_report_error mm/kasan/report.c:354 [inline] kasan_report.cold.7+0x242/0x2fe mm/kasan/report.c:412 __asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:433 timer_is_static_object+0x80/0x90 kernel/time/timer.c:607 debug_object_activate+0x2d9/0x670 lib/debugobjects.c:508 debug_timer_activate kernel/time/timer.c:709 [inline] debug_activate kernel/time/timer.c:764 [inline] __mod_timer kernel/time/timer.c:1041 [inline] mod_timer+0x4d3/0x13b0 kernel/time/timer.c:1102 sk_reset_timer+0x22/0x60 net/core/sock.c:2742 ccid2_hc_tx_rto_expire+0x587/0x680 net/dccp/ccids/ccid2.c:147 call_timer_fn+0x230/0x940 kernel/time/timer.c:1326 expire_timers kernel/time/timer.c:1363 [inline] __run_timers+0x79e/0xc50 kernel/time/timer.c:1666 run_timer_softirq+0x4c/0x70 kernel/time/timer.c:1692 __do_softirq+0x2e0/0xaf5 kernel/softirq.c:285 invoke_softirq kernel/softirq.c:365 [inline] irq_exit+0x1d1/0x200 kernel/softirq.c:405 exiting_irq arch/x86/include/asm/apic.h:525 [inline] smp_apic_timer_interrupt+0x17e/0x710 arch/x86/kernel/apic/apic.c:1052 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:863 </IRQ> ... Allocated by task 25374: save_stack+0x43/0xd0 mm/kasan/kasan.c:448 set_track mm/kasan/kasan.c:460 [inline] kasan_kmalloc+0xc4/0xe0 mm/kasan/kasan.c:553 kasan_slab_alloc+0x12/0x20 mm/kasan/kasan.c:490 kmem_cache_alloc+0x12e/0x760 mm/slab.c:3554 ccid_new+0x25b/0x3e0 net/dccp/ccid.c:151 dccp_hdlr_ccid+0x27/0x150 net/dccp/feat.c:44 __dccp_feat_activate+0x184/0x270 net/dccp/feat.c:344 dccp_feat_activate_values+0x3a7/0x819 net/dccp/feat.c:1538 dccp_create_openreq_child+0x472/0x610 net/dccp/minisocks.c:128 dccp_v4_request_recv_sock+0x12c/0xca0 net/dccp/ipv4.c:408 dccp_v6_request_recv_sock+0x125d/0x1f10 net/dccp/ipv6.c:415 dccp_check_req+0x455/0x6a0 net/dccp/minisocks.c:197 dccp_v4_rcv+0x7b8/0x1f3f net/dccp/ipv4.c:841 ip_local_deliver_finish+0x2e3/0xd80 net/ipv4/ip_input.c:215 NF_HOOK include/linux/netfilter.h:288 [inline] ip_local_deliver+0x1e1/0x720 net/ipv4/ip_input.c:256 dst_input include/net/dst.h:450 [inline] ip_rcv_finish+0x81b/0x2200 net/ipv4/ip_input.c:396 NF_HOOK include/linux/netfilter.h:288 [inline] ip_rcv+0xb70/0x143d net/ipv4/ip_input.c:492 __netif_receive_skb_core+0x26f5/0x3630 net/core/dev.c:4592 __netif_receive_skb+0x2c/0x1e0 net/core/dev.c:4657 process_backlog+0x219/0x760 net/core/dev.c:5337 napi_poll net/core/dev.c:5735 [inline] net_rx_action+0x7b7/0x1930 net/core/dev.c:5801 __do_softirq+0x2e0/0xaf5 kernel/softirq.c:285 Freed by task 25374: save_stack+0x43/0xd0 mm/kasan/kasan.c:448 set_track mm/kasan/kasan.c:460 [inline] __kasan_slab_free+0x11a/0x170 mm/kasan/kasan.c:521 kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528 __cache_free mm/slab.c:3498 [inline] kmem_cache_free+0x86/0x2d0 mm/slab.c:3756 ccid_hc_tx_delete+0xc3/0x100 net/dccp/ccid.c:190 dccp_disconnect+0x130/0xc66 net/dccp/proto.c:286 dccp_close+0x3bc/0xe60 net/dccp/proto.c:1045 inet_release+0x104/0x1f0 net/ipv4/af_inet.c:427 inet6_release+0x50/0x70 net/ipv6/af_inet6.c:460 sock_release+0x96/0x1b0 net/socket.c:594 sock_close+0x16/0x20 net/socket.c:1149 __fput+0x34d/0x890 fs/file_table.c:209 ____fput+0x15/0x20 fs/file_table.c:243 task_work_run+0x1e4/0x290 kernel/task_work.c:113 tracehook_notify_resume include/linux/tracehook.h:191 [inline] exit_to_usermode_loop+0x2bd/0x310 arch/x86/entry/common.c:166 prepare_exit_to_usermode arch/x86/entry/common.c:196 [inline] syscall_return_slowpath arch/x86/entry/common.c:265 [inline] do_syscall_64+0x6ac/0x800 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe The buggy address belongs to the object at ffff8801bebb4cc0 which belongs to the cache ccid2_hc_tx_sock of size 1240 The buggy address is located 1112 bytes inside of 1240-byte region [ffff8801bebb4cc0, ffff8801bebb5198) The buggy address belongs to the page: page:ffffea0006faed00 count:1 mapcount:0 mapping:ffff8801bebb41c0 index:0xffff8801bebb5240 compound_mapcount: 0 flags: 0x2fffc0000008100(slab|head) raw: 02fffc0000008100 ffff8801bebb41c0 ffff8801bebb5240 0000000100000003 raw: ffff8801cdba3138 ffffea0007634120 ffff8801cdbaab40 0000000000000000 page dumped because: kasan: bad access detected ... ================================================================== Reported-by: syzbot+5d47e9ec91a6f15dbd6f@syzkaller.appspotmail.com Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 322eaa0 ] In commit 624dbf5 ("driver/net: enic: Try DMA 64 first, then failover to DMA") DMA mask was changed from 40 bits to 64 bits. Hardware actually supports only 47 bits. Fixes: 624dbf5 ("driver/net: enic: Try DMA 64 first, then failover to DMA") Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…eeds [ Upstream commit 848235e ] Currently, raw6_sk(sk)->ip6mr_table is set unconditionally during ip6_mroute_setsockopt(MRT6_TABLE). A subsequent attempt at the same setsockopt will fail with -ENOENT, since we haven't actually created that table. A similar fix for ipv4 was included in commit 5e1859f ("ipv4: ipmr: various fixes and cleanups"). Fixes: d1db275 ("ipv6: ip6mr: support multiple tables") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 730c54d ] A precondition check in ip_recv_error triggered on an otherwise benign race. Remove the warning. The warning triggers when passing an ipv6 socket to this ipv4 error handling function. RaceFuzzer was able to trigger it due to a race in setsockopt IPV6_ADDRFORM. --- CPU0 do_ipv6_setsockopt sk->sk_socket->ops = &inet_dgram_ops; --- CPU1 sk->sk_prot->recvmsg udp_recvmsg ip_recv_error WARN_ON_ONCE(sk->sk_family == AF_INET6); --- CPU0 do_ipv6_setsockopt sk->sk_family = PF_INET; This socket option converts a v6 socket that is connected to a v4 peer to an v4 socket. It updates the socket on the fly, changing fields in sk as well as other structs. This is inherently non-atomic. It races with the lockless udp_recvmsg path. No other code makes an assumption that these fields are updated atomically. It is benign here, too, as ip_recv_error cares only about the protocol of the skbs enqueued on the error queue, for which sk_family is not a precise predictor (thanks to another isue with IPV6_ADDRFORM). Link: http://lkml.kernel.org/r/20180518120826.GA19515@dragonet.kaist.ac.kr Fixes: 7ce875e ("ipv4: warn once on passing AF_INET6 socket to ip_recv_error") Reported-by: DaeRyong Jeong <threeearcat@gmail.com> Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 6009d1f ] In divasmain.c, the function divas_write() firstly invokes the function diva_xdi_open_adapter() to open the adapter that matches with the adapter number provided by the user, and then invokes the function diva_xdi_write() to perform the write operation using the matched adapter. The two functions diva_xdi_open_adapter() and diva_xdi_write() are located in diva.c. In diva_xdi_open_adapter(), the user command is copied to the object 'msg' from the userspace pointer 'src' through the function pointer 'cp_fn', which eventually calls copy_from_user() to do the copy. Then, the adapter number 'msg.adapter' is used to find out a matched adapter from the 'adapter_queue'. A matched adapter will be returned if it is found. Otherwise, NULL is returned to indicate the failure of the verification on the adapter number. As mentioned above, if a matched adapter is returned, the function diva_xdi_write() is invoked to perform the write operation. In this function, the user command is copied once again from the userspace pointer 'src', which is the same as the 'src' pointer in diva_xdi_open_adapter() as both of them are from the 'buf' pointer in divas_write(). Similarly, the copy is achieved through the function pointer 'cp_fn', which finally calls copy_from_user(). After the successful copy, the corresponding command processing handler of the matched adapter is invoked to perform the write operation. It is obvious that there are two copies here from userspace, one is in diva_xdi_open_adapter(), and one is in diva_xdi_write(). Plus, both of these two copies share the same source userspace pointer, i.e., the 'buf' pointer in divas_write(). Given that a malicious userspace process can race to change the content pointed by the 'buf' pointer, this can pose potential security issues. For example, in the first copy, the user provides a valid adapter number to pass the verification process and a valid adapter can be found. Then the user can modify the adapter number to an invalid number. This way, the user can bypass the verification process of the adapter number and inject inconsistent data. This patch reuses the data copied in diva_xdi_open_adapter() and passes it to diva_xdi_write(). This way, the above issues can be avoided. Signed-off-by: Wenwen Wang <wang6495@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit eb7f54b ] (resend for properly queueing in patchwork) kcm_clone() creates kernel socket, which does not take net counter. Thus, the net may die before the socket is completely destructed, i.e. kcm_exit_net() is executed before kcm_done(). Reported-by: syzbot+5f1a04e374a635efc426@syzkaller.appspotmail.com Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 75d4e70 ] Per discussion with David at netconf 2018, let's clarify DaveM's position of handling stable backports in netdev-FAQ. This is important for people relying on upstream -stable releases. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit eb73190 ] syzbot was able to trick af_packet again [1] Various commits tried to address the problem in the past, but failed to take into account V3 header size. [1] tpacket_rcv: packet too big, clamped from 72 to 4294967224. macoff=96 BUG: KASAN: use-after-free in prb_run_all_ft_ops net/packet/af_packet.c:1016 [inline] BUG: KASAN: use-after-free in prb_fill_curr_block.isra.59+0x4e5/0x5c0 net/packet/af_packet.c:1039 Write of size 2 at addr ffff8801cb62000e by task kworker/1:2/2106 CPU: 1 PID: 2106 Comm: kworker/1:2 Not tainted 4.17.0-rc7+ Freescale#77 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: ipv6_addrconf addrconf_dad_work Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1b9/0x294 lib/dump_stack.c:113 print_address_description+0x6c/0x20b mm/kasan/report.c:256 kasan_report_error mm/kasan/report.c:354 [inline] kasan_report.cold.7+0x242/0x2fe mm/kasan/report.c:412 __asan_report_store2_noabort+0x17/0x20 mm/kasan/report.c:436 prb_run_all_ft_ops net/packet/af_packet.c:1016 [inline] prb_fill_curr_block.isra.59+0x4e5/0x5c0 net/packet/af_packet.c:1039 __packet_lookup_frame_in_block net/packet/af_packet.c:1094 [inline] packet_current_rx_frame net/packet/af_packet.c:1117 [inline] tpacket_rcv+0x1866/0x3340 net/packet/af_packet.c:2282 dev_queue_xmit_nit+0x891/0xb90 net/core/dev.c:2018 xmit_one net/core/dev.c:3049 [inline] dev_hard_start_xmit+0x16b/0xc10 net/core/dev.c:3069 __dev_queue_xmit+0x2724/0x34c0 net/core/dev.c:3584 dev_queue_xmit+0x17/0x20 net/core/dev.c:3617 neigh_resolve_output+0x679/0xad0 net/core/neighbour.c:1358 neigh_output include/net/neighbour.h:482 [inline] ip6_finish_output2+0xc9c/0x2810 net/ipv6/ip6_output.c:120 ip6_finish_output+0x5fe/0xbc0 net/ipv6/ip6_output.c:154 NF_HOOK_COND include/linux/netfilter.h:277 [inline] ip6_output+0x227/0x9b0 net/ipv6/ip6_output.c:171 dst_output include/net/dst.h:444 [inline] NF_HOOK include/linux/netfilter.h:288 [inline] ndisc_send_skb+0x100d/0x1570 net/ipv6/ndisc.c:491 ndisc_send_ns+0x3c1/0x8d0 net/ipv6/ndisc.c:633 addrconf_dad_work+0xbef/0x1340 net/ipv6/addrconf.c:4033 process_one_work+0xc1e/0x1b50 kernel/workqueue.c:2145 worker_thread+0x1cc/0x1440 kernel/workqueue.c:2279 kthread+0x345/0x410 kernel/kthread.c:240 ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:412 The buggy address belongs to the page: page:ffffea00072d8800 count:0 mapcount:-127 mapping:0000000000000000 index:0xffff8801cb620e80 flags: 0x2fffc0000000000() raw: 02fffc0000000000 0000000000000000 ffff8801cb620e80 00000000ffffff80 raw: ffffea00072e3820 ffffea0007132d20 0000000000000002 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8801cb61ff00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff8801cb61ff80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff8801cb620000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ^ ffff8801cb620080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff8801cb620100: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Fixes: 2b6867c ("net/packet: fix overflow in check for priv area size") Fixes: dc80811 ("packet: handle too big packets for PACKET_V3") Fixes: f6fb8f1 ("af-packet: TPACKET_V3 flexible buffer implementation.") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9f7c728 ] Testing Telit LM940 with ICMP packets > 14552 bytes revealed that the modem needs FLAG_SEND_ZLP to properly work, otherwise the cdc mbim data interface won't be anymore responsive. Signed-off-by: Daniele Palmas <dnlplm@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9aad13b ] Commit b84bbaf ("packet: in packet_snd start writing at link layer allocation") ensures that packet_snd always starts writing the link layer header in reserved headroom allocated for this purpose. This is needed because packets may be shorter than hard_header_len, in which case the space up to hard_header_len may be zeroed. But that necessary padding is not accounted for in skb->len. The fix, however, is buggy. It calls skb_push, which grows skb->len when moving skb->data back. But in this case packet length should not change. Instead, call skb_reserve, which moves both skb->data and skb->tail back, without changing length. Fixes: b84bbaf ("packet: in packet_snd start writing at link layer allocation") Reported-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit fdd13dd ] ILT entry requires 12 bit right shifted physical address. Existing mask for ILT entry of physical address i.e. ILT_ENTRY_PHY_ADDR_MASK is not sufficient to handle 64bit address because upper 8 bits of 64 bit address were getting masked which resulted in completer abort error on PCIe bus due to invalid address. Fix that mask to handle 64bit physical address. Fixes: fe56b9e ("qed: Add module with basic common support") Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 1d88ba1 ] syzbot reported a rcu_sched self-detected stall on CPU which is caused by too small value set on rto_min with SCTP_RTOINFO sockopt. With this value, hb_timer will get stuck there, as in its timer handler it starts this timer again with this value, then goes to the timer handler again. This problem is there since very beginning, and thanks to Eric for the reproducer shared from a syzbot mail. This patch fixes it by not allowing sctp_transport_timeout to return a smaller value than HZ/5 for hb_timer, which is based on TCP's min rto. Note that it doesn't fix this issue by limiting rto_min, as some users are still using small rto and no proper value was found for it yet. Reported-by: syzbot+3dcd59a1f907245f891f@syzkaller.appspotmail.com Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 25ea665 ] This code was introduced in 2011 around the same time that we made netdev_features_t a u64 type. These days a u32 is not big enough to hold all the potential features. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 1b15ad6 ] DaeRyong Jeong reports a race between vhost_dev_cleanup() and vhost_process_iotlb_msg(): Thread interleaving: CPU0 (vhost_process_iotlb_msg) CPU1 (vhost_dev_cleanup) (In the case of both VHOST_IOTLB_UPDATE and VHOST_IOTLB_INVALIDATE) ===== ===== vhost_umem_clean(dev->iotlb); if (!dev->iotlb) { ret = -EFAULT; break; } dev->iotlb = NULL; The reason is we don't synchronize between them, fixing by protecting vhost_process_iotlb_msg() with dev mutex. Reported-by: DaeRyong Jeong <threeearcat@gmail.com> Fixes: 6b1e6cc ("vhost: new device IOTLB API") Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 2f17bec ] Use the right device to determine if redirect should be sent especially when using vrf. Same as well as when sending the redirect. Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d546b67 ] spin_lock/unlock was used instead of spin_un/lock_irq in a procedure used in process space, on a spinlock which can be grabbed in an interrupt. This caused the stack trace below to be displayed (on kernel 4.17.0-rc1 compiled with Lock Debugging enabled): [ 154.661474] WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected [ 154.668909] 4.17.0-rc1-rdma_rc_mlx+ Freescale#3 Tainted: G I [ 154.675856] ----------------------------------------------------- [ 154.682706] modprobe/10159 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: [ 154.690254] 00000000f3b0e495 (&(&qp_table->lock)->rlock){+.+.}, at: mlx4_qp_remove+0x20/0x50 [mlx4_core] [ 154.700927] and this task is already holding: [ 154.707461] 0000000094373b5d (&(&cq->lock)->rlock/1){....}, at: destroy_qp_common+0x111/0x560 [mlx4_ib] [ 154.718028] which would create a new lock dependency: [ 154.723705] (&(&cq->lock)->rlock/1){....} -> (&(&qp_table->lock)->rlock){+.+.} [ 154.731922] but this new dependency connects a SOFTIRQ-irq-safe lock: [ 154.740798] (&(&cq->lock)->rlock){..-.} [ 154.740800] ... which became SOFTIRQ-irq-safe at: [ 154.752163] _raw_spin_lock_irqsave+0x3e/0x50 [ 154.757163] mlx4_ib_poll_cq+0x36/0x900 [mlx4_ib] [ 154.762554] ipoib_tx_poll+0x4a/0xf0 [ib_ipoib] ... to a SOFTIRQ-irq-unsafe lock: [ 154.815603] (&(&qp_table->lock)->rlock){+.+.} [ 154.815604] ... which became SOFTIRQ-irq-unsafe at: [ 154.827718] ... [ 154.827720] _raw_spin_lock+0x35/0x50 [ 154.833912] mlx4_qp_lookup+0x1e/0x50 [mlx4_core] [ 154.839302] mlx4_flow_attach+0x3f/0x3d0 [mlx4_core] Since mlx4_qp_lookup() is called only in process space, we can simply replace the spin_un/lock calls with spin_un/lock_irq calls. Fixes: 6dc06c0 ("net/mlx4: Fix the check in attaching steering rules") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 644c7ee ] It seems that rtnl_group_changelink() can call do_setlink while a prior call to validate_linkmsg(dev = NULL, ...) could not validate IFLA_ADDRESS / IFLA_BROADCAST Make sure do_setlink() calls validate_linkmsg() instead of letting its callers having this responsibility. With help from Dmitry Vyukov, thanks a lot ! BUG: KMSAN: uninit-value in is_valid_ether_addr include/linux/etherdevice.h:199 [inline] BUG: KMSAN: uninit-value in eth_prepare_mac_addr_change net/ethernet/eth.c:275 [inline] BUG: KMSAN: uninit-value in eth_mac_addr+0x203/0x2b0 net/ethernet/eth.c:308 CPU: 1 PID: 8695 Comm: syz-executor3 Not tainted 4.17.0-rc5+ Freescale#103 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x185/0x1d0 lib/dump_stack.c:113 kmsan_report+0x149/0x260 mm/kmsan/kmsan.c:1084 __msan_warning_32+0x6e/0xc0 mm/kmsan/kmsan_instr.c:686 is_valid_ether_addr include/linux/etherdevice.h:199 [inline] eth_prepare_mac_addr_change net/ethernet/eth.c:275 [inline] eth_mac_addr+0x203/0x2b0 net/ethernet/eth.c:308 dev_set_mac_address+0x261/0x530 net/core/dev.c:7157 do_setlink+0xbc3/0x5fc0 net/core/rtnetlink.c:2317 rtnl_group_changelink net/core/rtnetlink.c:2824 [inline] rtnl_newlink+0x1fe9/0x37a0 net/core/rtnetlink.c:2976 rtnetlink_rcv_msg+0xa32/0x1560 net/core/rtnetlink.c:4646 netlink_rcv_skb+0x378/0x600 net/netlink/af_netlink.c:2448 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:4664 netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline] netlink_unicast+0x1678/0x1750 net/netlink/af_netlink.c:1336 netlink_sendmsg+0x104f/0x1350 net/netlink/af_netlink.c:1901 sock_sendmsg_nosec net/socket.c:629 [inline] sock_sendmsg net/socket.c:639 [inline] ___sys_sendmsg+0xec0/0x1310 net/socket.c:2117 __sys_sendmsg net/socket.c:2155 [inline] __do_sys_sendmsg net/socket.c:2164 [inline] __se_sys_sendmsg net/socket.c:2162 [inline] __x64_sys_sendmsg+0x331/0x460 net/socket.c:2162 do_syscall_64+0x152/0x230 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x455a09 RSP: 002b:00007fc07480ec68 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007fc07480f6d4 RCX: 0000000000455a09 RDX: 0000000000000000 RSI: 00000000200003c0 RDI: 0000000000000014 RBP: 000000000072bea0 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff R13: 00000000000005d0 R14: 00000000006fdc20 R15: 0000000000000000 Uninit was stored to memory at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:279 [inline] kmsan_save_stack mm/kmsan/kmsan.c:294 [inline] kmsan_internal_chain_origin+0x12b/0x210 mm/kmsan/kmsan.c:685 kmsan_memcpy_origins+0x11d/0x170 mm/kmsan/kmsan.c:527 __msan_memcpy+0x109/0x160 mm/kmsan/kmsan_instr.c:478 do_setlink+0xb84/0x5fc0 net/core/rtnetlink.c:2315 rtnl_group_changelink net/core/rtnetlink.c:2824 [inline] rtnl_newlink+0x1fe9/0x37a0 net/core/rtnetlink.c:2976 rtnetlink_rcv_msg+0xa32/0x1560 net/core/rtnetlink.c:4646 netlink_rcv_skb+0x378/0x600 net/netlink/af_netlink.c:2448 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:4664 netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline] netlink_unicast+0x1678/0x1750 net/netlink/af_netlink.c:1336 netlink_sendmsg+0x104f/0x1350 net/netlink/af_netlink.c:1901 sock_sendmsg_nosec net/socket.c:629 [inline] sock_sendmsg net/socket.c:639 [inline] ___sys_sendmsg+0xec0/0x1310 net/socket.c:2117 __sys_sendmsg net/socket.c:2155 [inline] __do_sys_sendmsg net/socket.c:2164 [inline] __se_sys_sendmsg net/socket.c:2162 [inline] __x64_sys_sendmsg+0x331/0x460 net/socket.c:2162 do_syscall_64+0x152/0x230 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:279 [inline] kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:189 kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:315 kmsan_slab_alloc+0x10/0x20 mm/kmsan/kmsan.c:322 slab_post_alloc_hook mm/slab.h:446 [inline] slab_alloc_node mm/slub.c:2753 [inline] __kmalloc_node_track_caller+0xb32/0x11b0 mm/slub.c:4395 __kmalloc_reserve net/core/skbuff.c:138 [inline] __alloc_skb+0x2cb/0x9e0 net/core/skbuff.c:206 alloc_skb include/linux/skbuff.h:988 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1182 [inline] netlink_sendmsg+0x76e/0x1350 net/netlink/af_netlink.c:1876 sock_sendmsg_nosec net/socket.c:629 [inline] sock_sendmsg net/socket.c:639 [inline] ___sys_sendmsg+0xec0/0x1310 net/socket.c:2117 __sys_sendmsg net/socket.c:2155 [inline] __do_sys_sendmsg net/socket.c:2164 [inline] __se_sys_sendmsg net/socket.c:2162 [inline] __x64_sys_sendmsg+0x331/0x460 net/socket.c:2162 do_syscall_64+0x152/0x230 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: e7ed828 ("netlink: support setting devgroup parameters") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 79fb218 ] On newer PHYs, we need to select the expansion register to write with setting bits [11:8] to 0xf. This was done correctly by bcm7xxx.c prior to being migrated to generic code under bcm-phy-lib.c which unfortunately used the older implementation from the BCM54xx days. Fix this by creating an inline stub: bcm_write_exp_sel() which adds the correct value (MII_BCM54XX_EXP_SEL_ER) and update both the Cygnus PHY and BCM7xxx PHY drivers which require setting these bits. broadcom.c is unchanged because some PHYs even use a different selector method, so let them specify it directly (e.g: SerDes secondary selector). Fixes: a1cba56 ("net: phy: Add Broadcom phy library for common interfaces") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 5b5e7a0 ] Before using nla_get_u32(), better make sure the attribute is of the proper size. Code recently was changed, but bug has been there from beginning of git. BUG: KMSAN: uninit-value in rtnetlink_put_metrics+0x553/0x960 net/core/rtnetlink.c:746 CPU: 1 PID: 14139 Comm: syz-executor6 Not tainted 4.17.0-rc5+ Freescale#103 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x185/0x1d0 lib/dump_stack.c:113 kmsan_report+0x149/0x260 mm/kmsan/kmsan.c:1084 __msan_warning_32+0x6e/0xc0 mm/kmsan/kmsan_instr.c:686 rtnetlink_put_metrics+0x553/0x960 net/core/rtnetlink.c:746 fib_dump_info+0xc42/0x2190 net/ipv4/fib_semantics.c:1361 rtmsg_fib+0x65f/0x8c0 net/ipv4/fib_semantics.c:419 fib_table_insert+0x2314/0x2b50 net/ipv4/fib_trie.c:1287 inet_rtm_newroute+0x210/0x340 net/ipv4/fib_frontend.c:779 rtnetlink_rcv_msg+0xa32/0x1560 net/core/rtnetlink.c:4646 netlink_rcv_skb+0x378/0x600 net/netlink/af_netlink.c:2448 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:4664 netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline] netlink_unicast+0x1678/0x1750 net/netlink/af_netlink.c:1336 netlink_sendmsg+0x104f/0x1350 net/netlink/af_netlink.c:1901 sock_sendmsg_nosec net/socket.c:629 [inline] sock_sendmsg net/socket.c:639 [inline] ___sys_sendmsg+0xec0/0x1310 net/socket.c:2117 __sys_sendmsg net/socket.c:2155 [inline] __do_sys_sendmsg net/socket.c:2164 [inline] __se_sys_sendmsg net/socket.c:2162 [inline] __x64_sys_sendmsg+0x331/0x460 net/socket.c:2162 do_syscall_64+0x152/0x230 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x455a09 RSP: 002b:00007faae5fd8c68 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007faae5fd96d4 RCX: 0000000000455a09 RDX: 0000000000000000 RSI: 0000000020000000 RDI: 0000000000000013 RBP: 000000000072bea0 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff R13: 00000000000005d0 R14: 00000000006fdc20 R15: 0000000000000000 Uninit was stored to memory at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:279 [inline] kmsan_save_stack mm/kmsan/kmsan.c:294 [inline] kmsan_internal_chain_origin+0x12b/0x210 mm/kmsan/kmsan.c:685 __msan_chain_origin+0x69/0xc0 mm/kmsan/kmsan_instr.c:529 fib_convert_metrics net/ipv4/fib_semantics.c:1056 [inline] fib_create_info+0x2d46/0x9dc0 net/ipv4/fib_semantics.c:1150 fib_table_insert+0x3e4/0x2b50 net/ipv4/fib_trie.c:1146 inet_rtm_newroute+0x210/0x340 net/ipv4/fib_frontend.c:779 rtnetlink_rcv_msg+0xa32/0x1560 net/core/rtnetlink.c:4646 netlink_rcv_skb+0x378/0x600 net/netlink/af_netlink.c:2448 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:4664 netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline] netlink_unicast+0x1678/0x1750 net/netlink/af_netlink.c:1336 netlink_sendmsg+0x104f/0x1350 net/netlink/af_netlink.c:1901 sock_sendmsg_nosec net/socket.c:629 [inline] sock_sendmsg net/socket.c:639 [inline] ___sys_sendmsg+0xec0/0x1310 net/socket.c:2117 __sys_sendmsg net/socket.c:2155 [inline] __do_sys_sendmsg net/socket.c:2164 [inline] __se_sys_sendmsg net/socket.c:2162 [inline] __x64_sys_sendmsg+0x331/0x460 net/socket.c:2162 do_syscall_64+0x152/0x230 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:279 [inline] kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:189 kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:315 kmsan_slab_alloc+0x10/0x20 mm/kmsan/kmsan.c:322 slab_post_alloc_hook mm/slab.h:446 [inline] slab_alloc_node mm/slub.c:2753 [inline] __kmalloc_node_track_caller+0xb32/0x11b0 mm/slub.c:4395 __kmalloc_reserve net/core/skbuff.c:138 [inline] __alloc_skb+0x2cb/0x9e0 net/core/skbuff.c:206 alloc_skb include/linux/skbuff.h:988 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1182 [inline] netlink_sendmsg+0x76e/0x1350 net/netlink/af_netlink.c:1876 sock_sendmsg_nosec net/socket.c:629 [inline] sock_sendmsg net/socket.c:639 [inline] ___sys_sendmsg+0xec0/0x1310 net/socket.c:2117 __sys_sendmsg net/socket.c:2155 [inline] __do_sys_sendmsg net/socket.c:2164 [inline] __se_sys_sendmsg net/socket.c:2162 [inline] __x64_sys_sendmsg+0x331/0x460 net/socket.c:2162 do_syscall_64+0x152/0x230 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: a919525 ("net: Move fib_convert_metrics to metrics file") Fixes: 1da177e ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix an additional misuse of X86_FEATURE_SSBD in guest_cpuid_has_spec_ctrl(). This function was introduced in the backport of SSBD support to 4.9 and is not present upstream, so it was not fixed by commit 43462d9 "KVM: VMX: Expose SSBD properly to guests." Fixes: 5281758 ("x86/cpufeatures: Disentangle SSBD enumeration") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: kvm@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 590347e upstream. gcc-6.3 and earlier show a new warning after a seemingly unrelated change to the arm64 PAGE_KERNEL definition: In file included from drivers/md/dm-bufio.c:14:0: drivers/md/dm-bufio.c: In function 'alloc_buffer': include/linux/sched/mm.h:182:56: warning: 'noio_flag' may be used uninitialized in this function [-Wmaybe-uninitialized] current->flags = (current->flags & ~PF_MEMALLOC_NOIO) | flags; ^ The same warning happened earlier on linux-3.18 for MIPS and I did a workaround for that, but now it's come back. gcc-7 and newer are apparently smart enough to figure this out, and other architectures don't show it, so the best I could come up with is to rework the caller slightly in a way that makes it obvious enough to all arm64 compilers what is happening here. Fixes: 41acec6 ("arm64: kpti: Make use of nG dependent on arm64_kernel_unmapped_at_el0()") Link: https://patchwork.kernel.org/patch/9692829/ Cc: stable@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> [snitzer: moved declarations inside conditional, altered vmalloc return] Signed-off-by: Mike Snitzer <snitzer@redhat.com> [nc: Backport to 4.9, adjust context for lack of 19809c2] Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 867ac9d upstream. Objtool tries to silence 'unreachable instruction' warnings when it detects gcov is enabled, because gcov produces a lot of unreachable instructions and they don't really matter. However, the 0-day bot is still reporting some unreachable instruction warnings with CONFIG_GCOV_KERNEL=y on GCC 4.6.4. As it turns out, objtool's gcov detection doesn't work with older versions of GCC because they don't create a bunch of symbols with the 'gcov.' prefix like newer versions of GCC do. Move the gcov check out of objtool and instead just create a new '--no-unreachable' flag which can be passed in by the kernel Makefile when CONFIG_GCOV_KERNEL is defined. Also rename the 'nofp' variable to 'no_fp' for consistency with the new 'no_unreachable' variable. Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 9cfffb1 ("objtool: Skip all "unreachable instruction" warnings for gcov kernels") Link: http://lkml.kernel.org/r/c243dc78eb2ffdabb6e927844dea39b6033cd395.1500939244.git.jpoimboe@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> [just Makefile.build as the other parts of this patch already applied - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit eeb0efd upstream. This is the same sort of error we saw in commit 17e2e7d ("mm, page_alloc: fix has_unmovable_pages for HugePages"). Gigantic hugepages cross several memblocks, so it can be that the page we get in scan_movable_pages() is a page-tail belonging to a 1G-hugepage. If that happens, page_hstate()->size_to_hstate() will return NULL, and we will blow up in hugepage_migration_supported(). The splat is as follows: BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 #PF error: [normal kernel read fault] PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 1 PID: 1350 Comm: bash Tainted: G E 5.0.0-rc1-mm1-1-default+ #27 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014 RIP: 0010:__offline_pages+0x6ae/0x900 Call Trace: memory_subsys_offline+0x42/0x60 device_offline+0x80/0xa0 state_store+0xab/0xc0 kernfs_fop_write+0x102/0x180 __vfs_write+0x26/0x190 vfs_write+0xad/0x1b0 ksys_write+0x42/0x90 do_syscall_64+0x5b/0x180 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Modules linked in: af_packet(E) xt_tcpudp(E) ipt_REJECT(E) xt_conntrack(E) nf_conntrack(E) nf_defrag_ipv4(E) ip_set(E) nfnetlink(E) ebtable_nat(E) ebtable_broute(E) bridge(E) stp(E) llc(E) iptable_mangle(E) iptable_raw(E) iptable_security(E) ebtable_filter(E) ebtables(E) iptable_filter(E) ip_tables(E) x_tables(E) kvm_intel(E) kvm(E) irqbypass(E) crct10dif_pclmul(E) crc32_pclmul(E) ghash_clmulni_intel(E) bochs_drm(E) ttm(E) aesni_intel(E) drm_kms_helper(E) aes_x86_64(E) crypto_simd(E) cryptd(E) glue_helper(E) drm(E) virtio_net(E) syscopyarea(E) sysfillrect(E) net_failover(E) sysimgblt(E) pcspkr(E) failover(E) i2c_piix4(E) fb_sys_fops(E) parport_pc(E) parport(E) button(E) btrfs(E) libcrc32c(E) xor(E) zstd_decompress(E) zstd_compress(E) xxhash(E) raid6_pq(E) sd_mod(E) ata_generic(E) ata_piix(E) ahci(E) libahci(E) libata(E) crc32c_intel(E) serio_raw(E) virtio_pci(E) virtio_ring(E) virtio(E) sg(E) scsi_mod(E) autofs4(E) [akpm@linux-foundation.org: fix brace layout, per David. Reduce indentation] Link: http://lkml.kernel.org/r/20190122154407.18417-1-osalvador@suse.de Signed-off-by: Oscar Salvador <osalvador@suse.de> Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit dad0653 ] In virtualized setup, when system reboots due to warm reset interrupt storm is seen. Call Trace: <IRQ> dump_stack+0x70/0xa5 __report_bad_irq+0x2e/0xc0 note_interrupt+0x248/0x290 ? add_interrupt_randomness+0x30/0x220 handle_irq_event_percpu+0x54/0x80 handle_irq_event+0x39/0x60 handle_fasteoi_irq+0x91/0x150 handle_irq+0x108/0x180 do_IRQ+0x52/0xf0 common_interrupt+0xf/0xf </IRQ> RIP: 0033:0x76fc2cfabc1d Code: 24 28 bf 03 00 00 00 31 c0 48 8d 35 63 77 0e 00 48 8d 15 2e 94 0e 00 4c 89 f9 49 89 d9 4c 89 d3 e8 b8 e2 01 00 48 8b 54 24 18 <48> 89 ef 48 89 de 4c 89 e1 e8 d5 97 01 00 84 c0 74 2d 48 8b 04 24 RSP: 002b:00007ffd247c1fc0 EFLAGS: 00000293 ORIG_RAX: ffffffffffffffda RAX: 0000000000000000 RBX: 00007ffd247c1ff0 RCX: 000000000003d3ce RDX: 0000000000000000 RSI: 00007ffd247c1ff0 RDI: 000076fc2cbb6010 RBP: 000076fc2cded010 R08: 00007ffd247c2210 R09: 00007ffd247c22a0 R10: 000076fc29465470 R11: 0000000000000000 R12: 00007ffd247c1fc0 R13: 000076fc2ce8e470 R14: 000076fc27ec9960 R15: 0000000000000414 handlers: [<000000000d3fa913>] idma64_irq Disabling IRQ Freescale#27 To avoid interrupt storm, set the device in reset state before bringing out the device from reset state. Changelog v2: - correct the subject line by adding "mfd: " Signed-off-by: Binbin Wu <binbin.wu@intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit dad0653 ] In virtualized setup, when system reboots due to warm reset interrupt storm is seen. Call Trace: <IRQ> dump_stack+0x70/0xa5 __report_bad_irq+0x2e/0xc0 note_interrupt+0x248/0x290 ? add_interrupt_randomness+0x30/0x220 handle_irq_event_percpu+0x54/0x80 handle_irq_event+0x39/0x60 handle_fasteoi_irq+0x91/0x150 handle_irq+0x108/0x180 do_IRQ+0x52/0xf0 common_interrupt+0xf/0xf </IRQ> RIP: 0033:0x76fc2cfabc1d Code: 24 28 bf 03 00 00 00 31 c0 48 8d 35 63 77 0e 00 48 8d 15 2e 94 0e 00 4c 89 f9 49 89 d9 4c 89 d3 e8 b8 e2 01 00 48 8b 54 24 18 <48> 89 ef 48 89 de 4c 89 e1 e8 d5 97 01 00 84 c0 74 2d 48 8b 04 24 RSP: 002b:00007ffd247c1fc0 EFLAGS: 00000293 ORIG_RAX: ffffffffffffffda RAX: 0000000000000000 RBX: 00007ffd247c1ff0 RCX: 000000000003d3ce RDX: 0000000000000000 RSI: 00007ffd247c1ff0 RDI: 000076fc2cbb6010 RBP: 000076fc2cded010 R08: 00007ffd247c2210 R09: 00007ffd247c22a0 R10: 000076fc29465470 R11: 0000000000000000 R12: 00007ffd247c1fc0 R13: 000076fc2ce8e470 R14: 000076fc27ec9960 R15: 0000000000000414 handlers: [<000000000d3fa913>] idma64_irq Disabling IRQ #27 To avoid interrupt storm, set the device in reset state before bringing out the device from reset state. Changelog v2: - correct the subject line by adding "mfd: " Signed-off-by: Binbin Wu <binbin.wu@intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

…ups with the same type [ Upstream commit 2a28468 ] [BUG] With fuzzed image and MIXED_GROUPS super flag, we can hit the following BUG_ON(): kernel BUG at fs/btrfs/delayed-ref.c:491! invalid opcode: 0000 [Freescale#1] PREEMPT SMP NOPTI CPU: 0 PID: 1849 Comm: sync Tainted: G O 5.2.0-custom Freescale#27 RIP: 0010:update_existing_head_ref.cold+0x44/0x46 [btrfs] Call Trace: add_delayed_ref_head+0x20c/0x2d0 [btrfs] btrfs_add_delayed_tree_ref+0x1fc/0x490 [btrfs] btrfs_free_tree_block+0x123/0x380 [btrfs] __btrfs_cow_block+0x435/0x500 [btrfs] btrfs_cow_block+0x110/0x240 [btrfs] btrfs_search_slot+0x230/0xa00 [btrfs] ? __lock_acquire+0x105e/0x1e20 btrfs_insert_empty_items+0x67/0xc0 [btrfs] alloc_reserved_file_extent+0x9e/0x340 [btrfs] __btrfs_run_delayed_refs+0x78e/0x1240 [btrfs] ? kvm_clock_read+0x18/0x30 ? __sched_clock_gtod_offset+0x21/0x50 btrfs_run_delayed_refs.part.0+0x4e/0x180 [btrfs] btrfs_run_delayed_refs+0x23/0x30 [btrfs] btrfs_commit_transaction+0x53/0x9f0 [btrfs] btrfs_sync_fs+0x7c/0x1c0 [btrfs] ? __ia32_sys_fdatasync+0x20/0x20 sync_fs_one_sb+0x23/0x30 iterate_supers+0x95/0x100 ksys_sync+0x62/0xb0 __ia32_sys_sync+0xe/0x20 do_syscall_64+0x65/0x240 entry_SYSCALL_64_after_hwframe+0x49/0xbe [CAUSE] This situation is caused by several factors: - Fuzzed image The extent tree of this fs missed one backref for extent tree root. So we can allocated space from that slot. - MIXED_BG feature Super block has MIXED_BG flag. - No mixed block groups exists All block groups are just regular ones. This makes data space_info->block_groups[] contains metadata block groups. And when we reserve space for data, we can use space in metadata block group. Then we hit the following file operations: - fallocate We need to allocate data extents. find_free_extent() choose to use the metadata block to allocate space from, and choose the space of extent tree root, since its backref is missing. This generate one delayed ref head with is_data = 1. - extent tree update We need to update extent tree at run_delayed_ref time. This generate one delayed ref head with is_data = 0, for the same bytenr of old extent tree root. Then we trigger the BUG_ON(). [FIX] The quick fix here is to check block_group->flags before using it. The problem can only happen for MIXED_GROUPS fs. Regular filesystems won't have space_info with DATA|METADATA flag, and no way to hit the bug. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203255 Reported-by: Jungyeon Yoon <jungyeon.yoon@gmail.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit dad0653 ] In virtualized setup, when system reboots due to warm reset interrupt storm is seen. Call Trace: <IRQ> dump_stack+0x70/0xa5 __report_bad_irq+0x2e/0xc0 note_interrupt+0x248/0x290 ? add_interrupt_randomness+0x30/0x220 handle_irq_event_percpu+0x54/0x80 handle_irq_event+0x39/0x60 handle_fasteoi_irq+0x91/0x150 handle_irq+0x108/0x180 do_IRQ+0x52/0xf0 common_interrupt+0xf/0xf </IRQ> RIP: 0033:0x76fc2cfabc1d Code: 24 28 bf 03 00 00 00 31 c0 48 8d 35 63 77 0e 00 48 8d 15 2e 94 0e 00 4c 89 f9 49 89 d9 4c 89 d3 e8 b8 e2 01 00 48 8b 54 24 18 <48> 89 ef 48 89 de 4c 89 e1 e8 d5 97 01 00 84 c0 74 2d 48 8b 04 24 RSP: 002b:00007ffd247c1fc0 EFLAGS: 00000293 ORIG_RAX: ffffffffffffffda RAX: 0000000000000000 RBX: 00007ffd247c1ff0 RCX: 000000000003d3ce RDX: 0000000000000000 RSI: 00007ffd247c1ff0 RDI: 000076fc2cbb6010 RBP: 000076fc2cded010 R08: 00007ffd247c2210 R09: 00007ffd247c22a0 R10: 000076fc29465470 R11: 0000000000000000 R12: 00007ffd247c1fc0 R13: 000076fc2ce8e470 R14: 000076fc27ec9960 R15: 0000000000000414 handlers: [<000000000d3fa913>] idma64_irq Disabling IRQ Freescale#27 To avoid interrupt storm, set the device in reset state before bringing out the device from reset state. Changelog v2: - correct the subject line by adding "mfd: " Signed-off-by: Binbin Wu <binbin.wu@intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 96298f6 ] According to Core Spec Version 5.2 | Vol 3, Part A 6.1.5, the incoming L2CAP_ConfigReq should be handled during OPEN state. The section below shows the btmon trace when running L2CAP/COS/CFD/BV-12-C before and after this change. === Before === ... > ACL Data RX: Handle 256 flags 0x02 dlen 12 Freescale#22 L2CAP: Connection Request (0x02) ident 2 len 4 PSM: 1 (0x0001) Source CID: 65 < ACL Data TX: Handle 256 flags 0x00 dlen 16 Freescale#23 L2CAP: Connection Response (0x03) ident 2 len 8 Destination CID: 64 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 256 flags 0x00 dlen 12 Freescale#24 L2CAP: Configure Request (0x04) ident 2 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#25 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#26 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 16 Freescale#27 L2CAP: Configure Request (0x04) ident 3 len 8 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 .. < ACL Data TX: Handle 256 flags 0x00 dlen 18 Freescale#28 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#29 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 14 Freescale#30 L2CAP: Configure Response (0x05) ident 2 len 6 Source CID: 64 Flags: 0x0000 Result: Success (0x0000) > ACL Data RX: Handle 256 flags 0x02 dlen 20 Freescale#31 L2CAP: Configure Request (0x04) ident 3 len 12 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 91 02 11 11 ...... < ACL Data TX: Handle 256 flags 0x00 dlen 14 Freescale#32 L2CAP: Command Reject (0x01) ident 3 len 6 Reason: Invalid CID in request (0x0002) Destination CID: 64 Source CID: 65 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#33 Num handles: 1 Handle: 256 Count: 1 ... === After === ... > ACL Data RX: Handle 256 flags 0x02 dlen 12 Freescale#22 L2CAP: Connection Request (0x02) ident 2 len 4 PSM: 1 (0x0001) Source CID: 65 < ACL Data TX: Handle 256 flags 0x00 dlen 16 Freescale#23 L2CAP: Connection Response (0x03) ident 2 len 8 Destination CID: 64 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 256 flags 0x00 dlen 12 Freescale#24 L2CAP: Configure Request (0x04) ident 2 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#25 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#26 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 16 Freescale#27 L2CAP: Configure Request (0x04) ident 3 len 8 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 .. < ACL Data TX: Handle 256 flags 0x00 dlen 18 Freescale#28 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#29 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 14 Freescale#30 L2CAP: Configure Response (0x05) ident 2 len 6 Source CID: 64 Flags: 0x0000 Result: Success (0x0000) > ACL Data RX: Handle 256 flags 0x02 dlen 20 Freescale#31 L2CAP: Configure Request (0x04) ident 3 len 12 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 91 02 11 11 ..... < ACL Data TX: Handle 256 flags 0x00 dlen 18 Freescale#32 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 < ACL Data TX: Handle 256 flags 0x00 dlen 12 Freescale#33 L2CAP: Configure Request (0x04) ident 3 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#34 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#35 Num handles: 1 Handle: 256 Count: 1 ... Signed-off-by: Howard Chung <howardchung@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

If cm_create_timewait_info() fails, the timewait_info pointer will contain an error value and will be used in cm_remove_remote() later. general protection fault, probably for non-canonical address 0xdffffc0000000024: 0000 [#1] SMP KASAN PTI KASAN: null-ptr-deref in range [0×0000000000000120-0×0000000000000127] CPU: 2 PID: 12446 Comm: syz-executor.3 Not tainted 5.10.0-rc5-5d4c0742a60e #27 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:cm_remove_remote.isra.0+0x24/0×170 drivers/infiniband/core/cm.c:978 Code: 84 00 00 00 00 00 41 54 55 53 48 89 fb 48 8d ab 2d 01 00 00 e8 7d bf 4b fe 48 89 ea 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <0f> b6 04 02 48 89 ea 83 e2 07 38 d0 7f 08 84 c0 0f 85 fc 00 00 00 RSP: 0018:ffff888013127918 EFLAGS: 00010006 RAX: dffffc0000000000 RBX: fffffffffffffff4 RCX: ffffc9000a18b000 RDX: 0000000000000024 RSI: ffffffff82edc573 RDI: fffffffffffffff4 RBP: 0000000000000121 R08: 0000000000000001 R09: ffffed1002624f1d R10: 0000000000000003 R11: ffffed1002624f1c R12: ffff888107760c70 R13: ffff888107760c40 R14: fffffffffffffff4 R15: ffff888107760c9c FS: 00007fe1ffcc1700(0000) GS:ffff88811a600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000001b2ff21000 CR3: 000000010f504001 CR4: 0000000000370ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: cm_destroy_id+0x189/0×15b0 drivers/infiniband/core/cm.c:1155 cma_connect_ib drivers/infiniband/core/cma.c:4029 [inline] rdma_connect_locked+0x1100/0×17c0 drivers/infiniband/core/cma.c:4107 rdma_connect+0x2a/0×40 drivers/infiniband/core/cma.c:4140 ucma_connect+0x277/0×340 drivers/infiniband/core/ucma.c:1069 ucma_write+0x236/0×2f0 drivers/infiniband/core/ucma.c:1724 vfs_write+0x220/0×830 fs/read_write.c:603 ksys_write+0x1df/0×240 fs/read_write.c:658 do_syscall_64+0x33/0×40 arch/x86/entry/common.c:46 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: a977049 ("[PATCH] IB: Add the kernel CM implementation") Link: https://lore.kernel.org/r/20201204064205.145795-1-leon@kernel.org Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Reported-by: Amit Matityahu <mitm@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>

[ Upstream commit 340b940 ] If cm_create_timewait_info() fails, the timewait_info pointer will contain an error value and will be used in cm_remove_remote() later. general protection fault, probably for non-canonical address 0xdffffc0000000024: 0000 [Freescale#1] SMP KASAN PTI KASAN: null-ptr-deref in range [0×0000000000000120-0×0000000000000127] CPU: 2 PID: 12446 Comm: syz-executor.3 Not tainted 5.10.0-rc5-5d4c0742a60e Freescale#27 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:cm_remove_remote.isra.0+0x24/0×170 drivers/infiniband/core/cm.c:978 Code: 84 00 00 00 00 00 41 54 55 53 48 89 fb 48 8d ab 2d 01 00 00 e8 7d bf 4b fe 48 89 ea 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <0f> b6 04 02 48 89 ea 83 e2 07 38 d0 7f 08 84 c0 0f 85 fc 00 00 00 RSP: 0018:ffff888013127918 EFLAGS: 00010006 RAX: dffffc0000000000 RBX: fffffffffffffff4 RCX: ffffc9000a18b000 RDX: 0000000000000024 RSI: ffffffff82edc573 RDI: fffffffffffffff4 RBP: 0000000000000121 R08: 0000000000000001 R09: ffffed1002624f1d R10: 0000000000000003 R11: ffffed1002624f1c R12: ffff888107760c70 R13: ffff888107760c40 R14: fffffffffffffff4 R15: ffff888107760c9c FS: 00007fe1ffcc1700(0000) GS:ffff88811a600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000001b2ff21000 CR3: 000000010f504001 CR4: 0000000000370ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: cm_destroy_id+0x189/0×15b0 drivers/infiniband/core/cm.c:1155 cma_connect_ib drivers/infiniband/core/cma.c:4029 [inline] rdma_connect_locked+0x1100/0×17c0 drivers/infiniband/core/cma.c:4107 rdma_connect+0x2a/0×40 drivers/infiniband/core/cma.c:4140 ucma_connect+0x277/0×340 drivers/infiniband/core/ucma.c:1069 ucma_write+0x236/0×2f0 drivers/infiniband/core/ucma.c:1724 vfs_write+0x220/0×830 fs/read_write.c:603 ksys_write+0x1df/0×240 fs/read_write.c:658 do_syscall_64+0x33/0×40 arch/x86/entry/common.c:46 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: a977049 ("[PATCH] IB: Add the kernel CM implementation") Link: https://lore.kernel.org/r/20201204064205.145795-1-leon@kernel.org Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Reported-by: Amit Matityahu <mitm@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d5027ca ] Ritesh reported a bug [1] against UML, noting that it crashed on startup. The backtrace shows the following (heavily redacted): (gdb) bt ... Freescale#26 0x0000000060015b5d in sem_init () at ipc/sem.c:268 Freescale#27 0x00007f89906d92f7 in ?? () from /lib/x86_64-linux-gnu/libcom_err.so.2 Freescale#28 0x00007f8990ab8fb2 in call_init (...) at dl-init.c:72 ... Freescale#40 0x00007f89909bf3a6 in nss_load_library (...) at nsswitch.c:359 ... Freescale#44 0x00007f8990895e35 in _nss_compat_getgrnam_r (...) at nss_compat/compat-grp.c:486 Freescale#45 0x00007f8990968b85 in __getgrnam_r [...] Freescale#46 0x00007f89909d6b77 in grantpt [...] Freescale#47 0x00007f8990a9394e in __GI_openpty [...] Freescale#48 0x00000000604a1f65 in openpty_cb (...) at arch/um/os-Linux/sigio.c:407 Freescale#49 0x00000000604a58d0 in start_idle_thread (...) at arch/um/os-Linux/skas/process.c:598 Freescale#50 0x0000000060004a3d in start_uml () at arch/um/kernel/skas/process.c:45 Freescale#51 0x00000000600047b2 in linux_main (...) at arch/um/kernel/um_arch.c:334 Freescale#52 0x000000006000574f in main (...) at arch/um/os-Linux/main.c:144 indicating that the UML function openpty_cb() calls openpty(), which internally calls __getgrnam_r(), which causes the nsswitch machinery to get started. This loads, through lots of indirection that I snipped, the libcom_err.so.2 library, which (in an unknown function, "??") calls sem_init(). Now, of course it wants to get libpthread's sem_init(), since it's linked against libpthread. However, the dynamic linker looks up that symbol against the binary first, and gets the kernel's sem_init(). Hajime Tazaki noted that "objcopy -L" can localize a symbol, so the dynamic linker wouldn't do the lookup this way. I tried, but for some reason that didn't seem to work. Doing the same thing in the linker script instead does seem to work, though I cannot entirely explain - it *also* works if I just add "VERSION { { global: *; }; }" instead, indicating that something else is happening that I don't really understand. It may be that explicitly doing that marks them with some kind of empty version, and that's different from the default. Explicitly marking them with a version breaks kallsyms, so that doesn't seem to be possible. Marking all the symbols as local seems correct, and does seem to address the issue, so do that. Also do it for static link, nsswitch libraries could still be loaded there. [1] https://bugs.debian.org/983379 Reported-by: Ritesh Raj Sarraf <rrs@debian.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com> Tested-By: Ritesh Raj Sarraf <rrs@debian.org> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d412137 ] The perf_buffer fails on system with offline cpus: # test_progs -t perf_buffer test_perf_buffer:PASS:nr_cpus 0 nsec test_perf_buffer:PASS:nr_on_cpus 0 nsec test_perf_buffer:PASS:skel_load 0 nsec test_perf_buffer:PASS:attach_kprobe 0 nsec test_perf_buffer:PASS:perf_buf__new 0 nsec test_perf_buffer:PASS:epoll_fd 0 nsec skipping offline CPU Freescale#24 skipping offline CPU Freescale#25 skipping offline CPU Freescale#26 skipping offline CPU Freescale#27 skipping offline CPU Freescale#28 skipping offline CPU Freescale#29 skipping offline CPU Freescale#30 skipping offline CPU Freescale#31 test_perf_buffer:PASS:perf_buffer__poll 0 nsec test_perf_buffer:PASS:seen_cpu_cnt 0 nsec test_perf_buffer:FAIL:buf_cnt got 24, expected 32 Summary: 0/0 PASSED, 0 SKIPPED, 1 FAILED Changing the test to check online cpus instead of possible. Signed-off-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20211021114132.8196-2-jolsa@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 64ea2d0 ] The change of devlink_alloc() to accept device makes sure that device is fully initialized and device_register() does nothing except allowing users to use that devlink instance. Such change ensures that no user input will be usable till that point and it eliminates the need to worry about internal locking as long as devlink_register is called last since all accesses to the devlink are during initialization. This change fixes the following lockdep warning. ====================================================== WARNING: possible circular locking dependency detected 5.14.0-rc2+ Freescale#27 Not tainted ------------------------------------------------------ devlink/265 is trying to acquire lock: ffff8880133c2bc0 (&dev->intf_state_mutex){+.+.}-{3:3}, at: mlx5_unload_one+0x1e/0xa0 [mlx5_core] but task is already holding lock: ffffffff8362b468 (devlink_mutex){+.+.}-{3:3}, at: devlink_nl_pre_doit+0x2b/0x8d0 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> Freescale#1 (devlink_mutex){+.+.}-{3:3}: __mutex_lock+0x149/0x1310 devlink_register+0xe7/0x280 mlx5_devlink_register+0x118/0x480 [mlx5_core] mlx5_init_one+0x34b/0x440 [mlx5_core] probe_one+0x480/0x6e0 [mlx5_core] pci_device_probe+0x2a0/0x4a0 really_probe+0x1cb/0xba0 __driver_probe_device+0x18f/0x470 driver_probe_device+0x49/0x120 __driver_attach+0x1ce/0x400 bus_for_each_dev+0x11e/0x1a0 bus_add_driver+0x309/0x570 driver_register+0x20f/0x390 0xffffffffa04a0062 do_one_initcall+0xd5/0x400 do_init_module+0x1c8/0x760 load_module+0x7d9d/0xa4b0 __do_sys_finit_module+0x118/0x1a0 do_syscall_64+0x3d/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae -> #0 (&dev->intf_state_mutex){+.+.}-{3:3}: __lock_acquire+0x2999/0x5a40 lock_acquire+0x1a9/0x4a0 __mutex_lock+0x149/0x1310 mlx5_unload_one+0x1e/0xa0 [mlx5_core] mlx5_devlink_reload_down+0x185/0x2b0 [mlx5_core] devlink_reload+0x1f2/0x640 devlink_nl_cmd_reload+0x6c3/0x10d0 genl_family_rcv_msg_doit+0x1e9/0x2f0 genl_rcv_msg+0x27f/0x4a0 netlink_rcv_skb+0x11e/0x340 genl_rcv+0x24/0x40 netlink_unicast+0x433/0x700 netlink_sendmsg+0x6fb/0xbe0 sock_sendmsg+0xb0/0xe0 __sys_sendto+0x192/0x240 __x64_sys_sendto+0xdc/0x1b0 do_syscall_64+0x3d/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(devlink_mutex); lock(&dev->intf_state_mutex); lock(devlink_mutex); lock(&dev->intf_state_mutex); *** DEADLOCK *** 3 locks held by devlink/265: #0: ffffffff836371d0 (cb_lock){++++}-{3:3}, at: genl_rcv+0x15/0x40 Freescale#1: ffffffff83637288 (genl_mutex){+.+.}-{3:3}, at: genl_rcv_msg+0x31a/0x4a0 Freescale#2: ffffffff8362b468 (devlink_mutex){+.+.}-{3:3}, at: devlink_nl_pre_doit+0x2b/0x8d0 stack backtrace: CPU: 0 PID: 265 Comm: devlink Not tainted 5.14.0-rc2+ Freescale#27 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Call Trace: dump_stack_lvl+0x45/0x59 check_noncircular+0x268/0x310 ? print_circular_bug+0x460/0x460 ? __kernel_text_address+0xe/0x30 ? alloc_chain_hlocks+0x1e6/0x5a0 __lock_acquire+0x2999/0x5a40 ? lockdep_hardirqs_on_prepare+0x3e0/0x3e0 ? add_lock_to_list.constprop.0+0x6c/0x530 lock_acquire+0x1a9/0x4a0 ? mlx5_unload_one+0x1e/0xa0 [mlx5_core] ? lock_release+0x6c0/0x6c0 ? lockdep_hardirqs_on_prepare+0x3e0/0x3e0 ? lock_is_held_type+0x98/0x110 __mutex_lock+0x149/0x1310 ? mlx5_unload_one+0x1e/0xa0 [mlx5_core] ? lock_is_held_type+0x98/0x110 ? mlx5_unload_one+0x1e/0xa0 [mlx5_core] ? find_held_lock+0x2d/0x110 ? mutex_lock_io_nested+0x1160/0x1160 ? mlx5_lag_is_active+0x72/0x90 [mlx5_core] ? lock_downgrade+0x6d0/0x6d0 ? do_raw_spin_lock+0x12e/0x270 ? rwlock_bug.part.0+0x90/0x90 ? mlx5_unload_one+0x1e/0xa0 [mlx5_core] mlx5_unload_one+0x1e/0xa0 [mlx5_core] mlx5_devlink_reload_down+0x185/0x2b0 [mlx5_core] ? netlink_broadcast_filtered+0x308/0xac0 ? mlx5_devlink_info_get+0x1f0/0x1f0 [mlx5_core] ? __build_skb_around+0x110/0x2b0 ? __alloc_skb+0x113/0x2b0 devlink_reload+0x1f2/0x640 ? devlink_unregister+0x1e0/0x1e0 ? security_capable+0x51/0x90 devlink_nl_cmd_reload+0x6c3/0x10d0 ? devlink_nl_cmd_get_doit+0x1e0/0x1e0 ? devlink_nl_pre_doit+0x72/0x8d0 genl_family_rcv_msg_doit+0x1e9/0x2f0 ? __lock_acquire+0x15e2/0x5a40 ? genl_family_rcv_msg_attrs_parse.constprop.0+0x240/0x240 ? mutex_lock_io_nested+0x1160/0x1160 ? security_capable+0x51/0x90 genl_rcv_msg+0x27f/0x4a0 ? genl_get_cmd+0x3c0/0x3c0 ? lock_acquire+0x1a9/0x4a0 ? devlink_nl_cmd_get_doit+0x1e0/0x1e0 ? lock_release+0x6c0/0x6c0 netlink_rcv_skb+0x11e/0x340 ? genl_get_cmd+0x3c0/0x3c0 ? netlink_ack+0x930/0x930 genl_rcv+0x24/0x40 netlink_unicast+0x433/0x700 ? netlink_attachskb+0x750/0x750 ? __alloc_skb+0x113/0x2b0 netlink_sendmsg+0x6fb/0xbe0 ? netlink_unicast+0x700/0x700 ? netlink_unicast+0x700/0x700 sock_sendmsg+0xb0/0xe0 __sys_sendto+0x192/0x240 ? __x64_sys_getpeername+0xb0/0xb0 ? do_sys_openat2+0x10a/0x370 ? down_write_nested+0x150/0x150 ? do_user_addr_fault+0x215/0xd50 ? __x64_sys_openat+0x11f/0x1d0 ? __x64_sys_open+0x1a0/0x1a0 __x64_sys_sendto+0xdc/0x1b0 ? syscall_enter_from_user_mode+0x1d/0x50 do_syscall_64+0x3d/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f50b50b6b3a Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 76 c3 0f 1f 44 00 00 55 48 83 ec 30 44 89 4c RSP: 002b:00007fff6c0d3f38 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007f50b50b6b3a RDX: 0000000000000038 RSI: 000055763ac08440 RDI: 0000000000000003 RBP: 000055763ac08410 R08: 00007f50b5192200 R09: 000000000000000c R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000000 R14: 000055763ac08410 R15: 000055763ac08440 mlx5_core 0000:00:09.0: firmware version: 4.8.9999 mlx5_core 0000:00:09.0: 0.000 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x255 link) mlx5_core 0000:00:09.0 eth1: Link up Fixes: a6f3b62 ("net/mlx5: Move devlink registration before interfaces load") Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d412137 ] The perf_buffer fails on system with offline cpus: # test_progs -t perf_buffer test_perf_buffer:PASS:nr_cpus 0 nsec test_perf_buffer:PASS:nr_on_cpus 0 nsec test_perf_buffer:PASS:skel_load 0 nsec test_perf_buffer:PASS:attach_kprobe 0 nsec test_perf_buffer:PASS:perf_buf__new 0 nsec test_perf_buffer:PASS:epoll_fd 0 nsec skipping offline CPU Freescale#24 skipping offline CPU Freescale#25 skipping offline CPU Freescale#26 skipping offline CPU Freescale#27 skipping offline CPU Freescale#28 skipping offline CPU Freescale#29 skipping offline CPU Freescale#30 skipping offline CPU Freescale#31 test_perf_buffer:PASS:perf_buffer__poll 0 nsec test_perf_buffer:PASS:seen_cpu_cnt 0 nsec test_perf_buffer:FAIL:buf_cnt got 24, expected 32 Summary: 0/0 PASSED, 0 SKIPPED, 1 FAILED Changing the test to check online cpus instead of possible. Signed-off-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20211021114132.8196-2-jolsa@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d5027ca ] Ritesh reported a bug [1] against UML, noting that it crashed on startup. The backtrace shows the following (heavily redacted): (gdb) bt ... Freescale#26 0x0000000060015b5d in sem_init () at ipc/sem.c:268 Freescale#27 0x00007f89906d92f7 in ?? () from /lib/x86_64-linux-gnu/libcom_err.so.2 Freescale#28 0x00007f8990ab8fb2 in call_init (...) at dl-init.c:72 ... Freescale#40 0x00007f89909bf3a6 in nss_load_library (...) at nsswitch.c:359 ... Freescale#44 0x00007f8990895e35 in _nss_compat_getgrnam_r (...) at nss_compat/compat-grp.c:486 Freescale#45 0x00007f8990968b85 in __getgrnam_r [...] Freescale#46 0x00007f89909d6b77 in grantpt [...] Freescale#47 0x00007f8990a9394e in __GI_openpty [...] Freescale#48 0x00000000604a1f65 in openpty_cb (...) at arch/um/os-Linux/sigio.c:407 Freescale#49 0x00000000604a58d0 in start_idle_thread (...) at arch/um/os-Linux/skas/process.c:598 Freescale#50 0x0000000060004a3d in start_uml () at arch/um/kernel/skas/process.c:45 Freescale#51 0x00000000600047b2 in linux_main (...) at arch/um/kernel/um_arch.c:334 Freescale#52 0x000000006000574f in main (...) at arch/um/os-Linux/main.c:144 indicating that the UML function openpty_cb() calls openpty(), which internally calls __getgrnam_r(), which causes the nsswitch machinery to get started. This loads, through lots of indirection that I snipped, the libcom_err.so.2 library, which (in an unknown function, "??") calls sem_init(). Now, of course it wants to get libpthread's sem_init(), since it's linked against libpthread. However, the dynamic linker looks up that symbol against the binary first, and gets the kernel's sem_init(). Hajime Tazaki noted that "objcopy -L" can localize a symbol, so the dynamic linker wouldn't do the lookup this way. I tried, but for some reason that didn't seem to work. Doing the same thing in the linker script instead does seem to work, though I cannot entirely explain - it *also* works if I just add "VERSION { { global: *; }; }" instead, indicating that something else is happening that I don't really understand. It may be that explicitly doing that marks them with some kind of empty version, and that's different from the default. Explicitly marking them with a version breaks kallsyms, so that doesn't seem to be possible. Marking all the symbols as local seems correct, and does seem to address the issue, so do that. Also do it for static link, nsswitch libraries could still be loaded there. [1] https://bugs.debian.org/983379 Reported-by: Ritesh Raj Sarraf <rrs@debian.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com> Tested-By: Ritesh Raj Sarraf <rrs@debian.org> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit cefa91b upstream. Given a sufficiently large number of actions, while copying and reserving memory for a new action of a new flow, if next_offset is greater than MAX_ACTIONS_BUFSIZE, the function reserve_sfa_size() does not return -EMSGSIZE as expected, but it allocates MAX_ACTIONS_BUFSIZE bytes increasing actions_len by req_size. This can then lead to an OOB write access, especially when further actions need to be copied. Fix it by rearranging the flow action size check. KASAN splat below: ================================================================== BUG: KASAN: slab-out-of-bounds in reserve_sfa_size+0x1ba/0x380 [openvswitch] Write of size 65360 at addr ffff888147e4001c by task handler15/836 CPU: 1 PID: 836 Comm: handler15 Not tainted 5.18.0-rc1+ Freescale#27 ... Call Trace: <TASK> dump_stack_lvl+0x45/0x5a print_report.cold+0x5e/0x5db ? __lock_text_start+0x8/0x8 ? reserve_sfa_size+0x1ba/0x380 [openvswitch] kasan_report+0xb5/0x130 ? reserve_sfa_size+0x1ba/0x380 [openvswitch] kasan_check_range+0xf5/0x1d0 memcpy+0x39/0x60 reserve_sfa_size+0x1ba/0x380 [openvswitch] __add_action+0x24/0x120 [openvswitch] ovs_nla_add_action+0xe/0x20 [openvswitch] ovs_ct_copy_action+0x29d/0x1130 [openvswitch] ? __kernel_text_address+0xe/0x30 ? unwind_get_return_address+0x56/0xa0 ? create_prof_cpu_mask+0x20/0x20 ? ovs_ct_verify+0xf0/0xf0 [openvswitch] ? prep_compound_page+0x198/0x2a0 ? __kasan_check_byte+0x10/0x40 ? kasan_unpoison+0x40/0x70 ? ksize+0x44/0x60 ? reserve_sfa_size+0x75/0x380 [openvswitch] __ovs_nla_copy_actions+0xc26/0x2070 [openvswitch] ? __zone_watermark_ok+0x420/0x420 ? validate_set.constprop.0+0xc90/0xc90 [openvswitch] ? __alloc_pages+0x1a9/0x3e0 ? __alloc_pages_slowpath.constprop.0+0x1da0/0x1da0 ? unwind_next_frame+0x991/0x1e40 ? __mod_node_page_state+0x99/0x120 ? __mod_lruvec_page_state+0x2e3/0x470 ? __kasan_kmalloc_large+0x90/0xe0 ovs_nla_copy_actions+0x1b4/0x2c0 [openvswitch] ovs_flow_cmd_new+0x3cd/0xb10 [openvswitch] ... Cc: stable@vger.kernel.org Fixes: f28cd2a ("openvswitch: fix flow actions reallocation") Signed-off-by: Paolo Valerio <pvalerio@redhat.com> Acked-by: Eelco Chaudron <echaudro@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 49df342 ] when get fiemap starting from MAX_LFS_FILESIZE, (maxbytes - *len) < start will always true , then *len set zero. because of start offset is beyond file size, for erofs filesystem it will always return iomap.length with zero,iomap iterate will enter infinite loop. it is necessary cover this corner case to avoid this situation. ------------[ cut here ]------------ WARNING: CPU: 7 PID: 905 at fs/iomap/iter.c:35 iomap_iter+0x97f/0xc70 Modules linked in: xfs erofs CPU: 7 PID: 905 Comm: iomap Tainted: G W 5.17.0-rc8 Freescale#27 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 RIP: 0010:iomap_iter+0x97f/0xc70 Code: 85 a1 fc ff ff e8 71 be 9c ff 0f 1f 44 00 00 e9 92 fc ff ff e8 62 be 9c ff 0f 0b b8 fb ff ff ff e9 fc f8 ff ff e8 51 be 9c ff <0f> 0b e9 2b fc ff ff e8 45 be 9c ff 0f 0b e9 e1 fb ff ff e8 39 be RSP: 0018:ffff888060a37ab0 EFLAGS: 00010293 RAX: 0000000000000000 RBX: ffff888060a37bb0 RCX: 0000000000000000 RDX: ffff88807e19a900 RSI: ffffffff81a7da7f RDI: ffff888060a37be0 RBP: 7fffffffffffffff R08: 0000000000000000 R09: ffff888060a37c20 R10: ffff888060a37c67 R11: ffffed100c146f8c R12: 7fffffffffffffff R13: 0000000000000000 R14: ffff888060a37bd8 R15: ffff888060a37c20 FS: 00007fd3cca01540(0000) GS:ffff888108780000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020010820 CR3: 0000000054b92000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> iomap_fiemap+0x1c9/0x2f0 erofs_fiemap+0x64/0x90 [erofs] do_vfs_ioctl+0x40d/0x12e0 __x64_sys_ioctl+0xaa/0x1c0 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae </TASK> ---[ end trace 0000000000000000 ]--- watchdog: BUG: soft lockup - CPU#7 stuck for 26s! [iomap:905] Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Guo Xuenan <guoxuenan@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> [djwong: fix some typos] Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit f9a4300 upstream. __nft_release_hooks() is called from pre_netns exit path which unregisters the hooks, then the NETDEV_UNREGISTER event is triggered which unregisters the hooks again. [ 565.221461] WARNING: CPU: 18 PID: 193 at net/netfilter/core.c:495 __nf_unregister_net_hook+0x247/0x270 [...] [ 565.246890] CPU: 18 PID: 193 Comm: kworker/u64:1 Tainted: G E 5.18.0-rc7+ Freescale#27 [ 565.253682] Workqueue: netns cleanup_net [ 565.257059] RIP: 0010:__nf_unregister_net_hook+0x247/0x270 [...] [ 565.297120] Call Trace: [ 565.300900] <TASK> [ 565.304683] nf_tables_flowtable_event+0x16a/0x220 [nf_tables] [ 565.308518] raw_notifier_call_chain+0x63/0x80 [ 565.312386] unregister_netdevice_many+0x54f/0xb50 Unregister and destroy netdev hook from netns pre_exit via kfree_rcu so the NETDEV_UNREGISTER path see unregistered hooks. Fixes: 767d121 ("netfilter: nftables: fix possible UAF over chains from packet path in netns") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Handle both the legacy and prctl-based call forms available from Dovetail, i.e.: syscall(sys_evl_<op> | __OOB_SYSCALL_BIT, ...) /* old form */ syscall(__NR_prctl, sys_evl_<op> | __OOB_SYSCALL, ...) /* new form */ With this change, we gain out-of-the-box support for Valgrind since applications can now emit EVL system calls wrapped in prctl() requests, which are readily recognized by the instrumentation framework. As a result, the ABI number is bumped to Freescale#27. Signed-off-by: Philippe Gerum <rpm@xenomai.org>

commit 0b0747d upstream. The following processes run into a deadlock. CPU 41 was waiting for CPU 29 to handle a CSD request while holding spinlock "crashdump_lock", but CPU 29 was hung by that spinlock with IRQs disabled. PID: 17360 TASK: ffff95c1090c5c40 CPU: 41 COMMAND: "mrdiagd" !# 0 [ffffb80edbf37b58] __read_once_size at ffffffff9b871a40 include/linux/compiler.h:185:0 !# 1 [ffffb80edbf37b58] atomic_read at ffffffff9b871a40 arch/x86/include/asm/atomic.h:27:0 !# 2 [ffffb80edbf37b58] dump_stack at ffffffff9b871a40 lib/dump_stack.c:54:0 # 3 [ffffb80edbf37b78] csd_lock_wait_toolong at ffffffff9b131ad5 kernel/smp.c:364:0 # 4 [ffffb80edbf37b78] __csd_lock_wait at ffffffff9b131ad5 kernel/smp.c:384:0 # 5 [ffffb80edbf37bf8] csd_lock_wait at ffffffff9b13267a kernel/smp.c:394:0 # 6 [ffffb80edbf37bf8] smp_call_function_many at ffffffff9b13267a kernel/smp.c:843:0 # 7 [ffffb80edbf37c50] smp_call_function at ffffffff9b13279d kernel/smp.c:867:0 # 8 [ffffb80edbf37c50] on_each_cpu at ffffffff9b13279d kernel/smp.c:976:0 # 9 [ffffb80edbf37c78] flush_tlb_kernel_range at ffffffff9b085c4b arch/x86/mm/tlb.c:742:0 Freescale#10 [ffffb80edbf37cb8] __purge_vmap_area_lazy at ffffffff9b23a1e0 mm/vmalloc.c:701:0 Freescale#11 [ffffb80edbf37ce0] try_purge_vmap_area_lazy at ffffffff9b23a2cc mm/vmalloc.c:722:0 Freescale#12 [ffffb80edbf37ce0] free_vmap_area_noflush at ffffffff9b23a2cc mm/vmalloc.c:754:0 Freescale#13 [ffffb80edbf37cf8] free_unmap_vmap_area at ffffffff9b23bb3b mm/vmalloc.c:764:0 Freescale#14 [ffffb80edbf37cf8] remove_vm_area at ffffffff9b23bb3b mm/vmalloc.c:1509:0 Freescale#15 [ffffb80edbf37d18] __vunmap at ffffffff9b23bb8a mm/vmalloc.c:1537:0 Freescale#16 [ffffb80edbf37d40] vfree at ffffffff9b23bc85 mm/vmalloc.c:1612:0 Freescale#17 [ffffb80edbf37d58] megasas_free_host_crash_buffer [megaraid_sas] at ffffffffc020b7f2 drivers/scsi/megaraid/megaraid_sas_fusion.c:3932:0 Freescale#18 [ffffb80edbf37d80] fw_crash_state_store [megaraid_sas] at ffffffffc01f804d drivers/scsi/megaraid/megaraid_sas_base.c:3291:0 Freescale#19 [ffffb80edbf37dc0] dev_attr_store at ffffffff9b56dd7b drivers/base/core.c:758:0 Freescale#20 [ffffb80edbf37dd0] sysfs_kf_write at ffffffff9b326acf fs/sysfs/file.c:144:0 Freescale#21 [ffffb80edbf37de0] kernfs_fop_write at ffffffff9b325fd4 fs/kernfs/file.c:316:0 Freescale#22 [ffffb80edbf37e20] __vfs_write at ffffffff9b29418a fs/read_write.c:480:0 Freescale#23 [ffffb80edbf37ea8] vfs_write at ffffffff9b294462 fs/read_write.c:544:0 Freescale#24 [ffffb80edbf37ee8] SYSC_write at ffffffff9b2946ec fs/read_write.c:590:0 Freescale#25 [ffffb80edbf37ee8] SyS_write at ffffffff9b2946ec fs/read_write.c:582:0 Freescale#26 [ffffb80edbf37f30] do_syscall_64 at ffffffff9b003ca9 arch/x86/entry/common.c:298:0 Freescale#27 [ffffb80edbf37f58] entry_SYSCALL_64 at ffffffff9ba001b1 arch/x86/entry/entry_64.S:238:0 PID: 17355 TASK: ffff95c1090c3d80 CPU: 29 COMMAND: "mrdiagd" !# 0 [ffffb80f2d3c7d30] __read_once_size at ffffffff9b0f2ab0 include/linux/compiler.h:185:0 !# 1 [ffffb80f2d3c7d30] native_queued_spin_lock_slowpath at ffffffff9b0f2ab0 kernel/locking/qspinlock.c:368:0 # 2 [ffffb80f2d3c7d58] pv_queued_spin_lock_slowpath at ffffffff9b0f244b arch/x86/include/asm/paravirt.h:674:0 # 3 [ffffb80f2d3c7d58] queued_spin_lock_slowpath at ffffffff9b0f244b arch/x86/include/asm/qspinlock.h:53:0 # 4 [ffffb80f2d3c7d68] queued_spin_lock at ffffffff9b8961a6 include/asm-generic/qspinlock.h:90:0 # 5 [ffffb80f2d3c7d68] do_raw_spin_lock_flags at ffffffff9b8961a6 include/linux/spinlock.h:173:0 # 6 [ffffb80f2d3c7d68] __raw_spin_lock_irqsave at ffffffff9b8961a6 include/linux/spinlock_api_smp.h:122:0 # 7 [ffffb80f2d3c7d68] _raw_spin_lock_irqsave at ffffffff9b8961a6 kernel/locking/spinlock.c:160:0 # 8 [ffffb80f2d3c7d88] fw_crash_buffer_store [megaraid_sas] at ffffffffc01f8129 drivers/scsi/megaraid/megaraid_sas_base.c:3205:0 # 9 [ffffb80f2d3c7dc0] dev_attr_store at ffffffff9b56dd7b drivers/base/core.c:758:0 Freescale#10 [ffffb80f2d3c7dd0] sysfs_kf_write at ffffffff9b326acf fs/sysfs/file.c:144:0 Freescale#11 [ffffb80f2d3c7de0] kernfs_fop_write at ffffffff9b325fd4 fs/kernfs/file.c:316:0 Freescale#12 [ffffb80f2d3c7e20] __vfs_write at ffffffff9b29418a fs/read_write.c:480:0 Freescale#13 [ffffb80f2d3c7ea8] vfs_write at ffffffff9b294462 fs/read_write.c:544:0 Freescale#14 [ffffb80f2d3c7ee8] SYSC_write at ffffffff9b2946ec fs/read_write.c:590:0 Freescale#15 [ffffb80f2d3c7ee8] SyS_write at ffffffff9b2946ec fs/read_write.c:582:0 Freescale#16 [ffffb80f2d3c7f30] do_syscall_64 at ffffffff9b003ca9 arch/x86/entry/common.c:298:0 Freescale#17 [ffffb80f2d3c7f58] entry_SYSCALL_64 at ffffffff9ba001b1 arch/x86/entry/entry_64.S:238:0 The lock is used to synchronize different sysfs operations, it doesn't protect any resource that will be touched by an interrupt. Consequently it's not required to disable IRQs. Replace the spinlock with a mutex to fix the deadlock. Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Link: https://lore.kernel.org/r/20230828221018.19471-1-junxiao.bi@oracle.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b7cc4ff upstream. It appears the client object tree has no locking unless I've missed something else. Fix races around adding/removing client objects, mostly vram bar mappings. 4562.099306] general protection fault, probably for non-canonical address 0x6677ed422bceb80c: 0000 [Freescale#1] PREEMPT SMP PTI [ 4562.099314] CPU: 2 PID: 23171 Comm: deqp-vk Not tainted 6.8.0-rc6+ Freescale#27 [ 4562.099324] Hardware name: Gigabyte Technology Co., Ltd. Z390 I AORUS PRO WIFI/Z390 I AORUS PRO WIFI-CF, BIOS F8 11/05/2021 [ 4562.099330] RIP: 0010:nvkm_object_search+0x1d/0x70 [nouveau] [ 4562.099503] Code: 90 90 90 90 90 90 90 90 90 90 90 90 90 66 0f 1f 00 0f 1f 44 00 00 48 89 f8 48 85 f6 74 39 48 8b 87 a0 00 00 00 48 85 c0 74 12 <48> 8b 48 f8 48 39 ce 73 15 48 8b 40 10 48 85 c0 75 ee 48 c7 c0 fe [ 4562.099506] RSP: 0000:ffffa94cc420bbf8 EFLAGS: 00010206 [ 4562.099512] RAX: 6677ed422bceb814 RBX: ffff98108791f400 RCX: ffff9810f26b8f58 [ 4562.099517] RDX: 0000000000000000 RSI: ffff9810f26b9158 RDI: ffff98108791f400 [ 4562.099519] RBP: ffff9810f26b9158 R08: 0000000000000000 R09: 0000000000000000 [ 4562.099521] R10: ffffa94cc420bc48 R11: 0000000000000001 R12: ffff9810f02a7cc0 [ 4562.099526] R13: 0000000000000000 R14: 00000000000000ff R15: 0000000000000007 [ 4562.099528] FS: 00007f629c5017c0(0000) GS:ffff98142c700000(0000) knlGS:0000000000000000 [ 4562.099534] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 4562.099536] CR2: 00007f629a882000 CR3: 000000017019e004 CR4: 00000000003706f0 [ 4562.099541] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 4562.099542] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 4562.099544] Call Trace: [ 4562.099555] <TASK> [ 4562.099573] ? die_addr+0x36/0x90 [ 4562.099583] ? exc_general_protection+0x246/0x4a0 [ 4562.099593] ? asm_exc_general_protection+0x26/0x30 [ 4562.099600] ? nvkm_object_search+0x1d/0x70 [nouveau] [ 4562.099730] nvkm_ioctl+0xa1/0x250 [nouveau] [ 4562.099861] nvif_object_map_handle+0xc8/0x180 [nouveau] [ 4562.099986] nouveau_ttm_io_mem_reserve+0x122/0x270 [nouveau] [ 4562.100156] ? dma_resv_test_signaled+0x26/0xb0 [ 4562.100163] ttm_bo_vm_fault_reserved+0x97/0x3c0 [ttm] [ 4562.100182] ? __mutex_unlock_slowpath+0x2a/0x270 [ 4562.100189] nouveau_ttm_fault+0x69/0xb0 [nouveau] [ 4562.100356] __do_fault+0x32/0x150 [ 4562.100362] do_fault+0x7c/0x560 [ 4562.100369] __handle_mm_fault+0x800/0xc10 [ 4562.100382] handle_mm_fault+0x17c/0x3e0 [ 4562.100388] do_user_addr_fault+0x208/0x860 [ 4562.100395] exc_page_fault+0x7f/0x200 [ 4562.100402] asm_exc_page_fault+0x26/0x30 [ 4562.100412] RIP: 0033:0x9b9870 [ 4562.100419] Code: 85 a8 f7 ff ff 8b 8d 80 f7 ff ff 89 08 e9 18 f2 ff ff 0f 1f 84 00 00 00 00 00 44 89 32 e9 90 fa ff ff 0f 1f 84 00 00 00 00 00 <44> 89 32 e9 f8 f1 ff ff 0f 1f 84 00 00 00 00 00 66 44 89 32 e9 e7 [ 4562.100422] RSP: 002b:00007fff9ba2dc70 EFLAGS: 00010246 [ 4562.100426] RAX: 0000000000000004 RBX: 000000000dd65e10 RCX: 000000fff0000000 [ 4562.100428] RDX: 00007f629a882000 RSI: 00007f629a882000 RDI: 0000000000000066 [ 4562.100432] RBP: 00007fff9ba2e570 R08: 0000000000000000 R09: 0000000123ddf000 [ 4562.100434] R10: 0000000000000001 R11: 0000000000000246 R12: 000000007fffffff [ 4562.100436] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 [ 4562.100446] </TASK> [ 4562.100448] Modules linked in: nf_conntrack_netbios_ns nf_conntrack_broadcast nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables libcrc32c nfnetlink cmac bnep sunrpc iwlmvm intel_rapl_msr intel_rapl_common snd_sof_pci_intel_cnl x86_pkg_temp_thermal intel_powerclamp snd_sof_intel_hda_common mac80211 coretemp snd_soc_acpi_intel_match kvm_intel snd_soc_acpi snd_soc_hdac_hda snd_sof_pci snd_sof_xtensa_dsp snd_sof_intel_hda_mlink snd_sof_intel_hda snd_sof kvm snd_sof_utils snd_soc_core snd_hda_codec_realtek libarc4 snd_hda_codec_generic snd_compress snd_hda_ext_core vfat fat snd_hda_intel snd_intel_dspcfg irqbypass iwlwifi snd_hda_codec snd_hwdep snd_hda_core btusb btrtl mei_hdcp iTCO_wdt rapl mei_pxp btintel snd_seq iTCO_vendor_support btbcm snd_seq_device intel_cstate bluetooth snd_pcm cfg80211 intel_wmi_thunderbolt wmi_bmof intel_uncore snd_timer mei_me snd ecdh_generic i2c_i801 [ 4562.100541] ecc mei i2c_smbus soundcore rfkill intel_pch_thermal acpi_pad zram nouveau drm_ttm_helper ttm gpu_sched i2c_algo_bit drm_gpuvm drm_exec mxm_wmi drm_display_helper drm_kms_helper drm crct10dif_pclmul crc32_pclmul nvme e1000e crc32c_intel nvme_core ghash_clmulni_intel video wmi pinctrl_cannonlake ip6_tables ip_tables fuse [ 4562.100616] ---[ end trace 0000000000000000 ]--- Signed-off-by: Dave Airlie <airlied@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fff1386 upstream. Running a lot of VK CTS in parallel against nouveau, once every few hours you might see something like this crash. BUG: kernel NULL pointer dereference, address: 0000000000000008 PGD 8000000114e6e067 P4D 8000000114e6e067 PUD 109046067 PMD 0 Oops: 0000 [Freescale#1] PREEMPT SMP PTI CPU: 7 PID: 53891 Comm: deqp-vk Not tainted 6.8.0-rc6+ Freescale#27 Hardware name: Gigabyte Technology Co., Ltd. Z390 I AORUS PRO WIFI/Z390 I AORUS PRO WIFI-CF, BIOS F8 11/05/2021 RIP: 0010:gp100_vmm_pgt_mem+0xe3/0x180 [nouveau] Code: c7 48 01 c8 49 89 45 58 85 d2 0f 84 95 00 00 00 41 0f b7 46 12 49 8b 7e 08 89 da 42 8d 2c f8 48 8b 47 08 41 83 c7 01 48 89 ee <48> 8b 40 08 ff d0 0f 1f 00 49 8b 7e 08 48 89 d9 48 8d 75 04 48 c1 RSP: 0000:ffffac20c5857838 EFLAGS: 00010202 RAX: 0000000000000000 RBX: 00000000004d8001 RCX: 0000000000000001 RDX: 00000000004d8001 RSI: 00000000000006d8 RDI: ffffa07afe332180 RBP: 00000000000006d8 R08: ffffac20c5857ad0 R09: 0000000000ffff10 R10: 0000000000000001 R11: ffffa07af27e2de0 R12: 000000000000001c R13: ffffac20c5857ad0 R14: ffffa07a96fe9040 R15: 000000000000001c FS: 00007fe395eed7c0(0000) GS:ffffa07e2c980000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 000000011febe001 CR4: 00000000003706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: ... ? gp100_vmm_pgt_mem+0xe3/0x180 [nouveau] ? gp100_vmm_pgt_mem+0x37/0x180 [nouveau] nvkm_vmm_iter+0x351/0xa20 [nouveau] ? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau] ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau] ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau] ? __lock_acquire+0x3ed/0x2170 ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau] nvkm_vmm_ptes_get_map+0xc2/0x100 [nouveau] ? __pfx_nvkm_vmm_ref_ptes+0x10/0x10 [nouveau] ? __pfx_gp100_vmm_pgt_mem+0x10/0x10 [nouveau] nvkm_vmm_map_locked+0x224/0x3a0 [nouveau] Adding any sort of useful debug usually makes it go away, so I hand wrote the function in a line, and debugged the asm. Every so often pt->memory->ptrs is NULL. This ptrs ptr is set in the nv50_instobj_acquire called from nvkm_kmap. If Thread A and Thread B both get to nv50_instobj_acquire around the same time, and Thread A hits the refcount_set line, and in lockstep thread B succeeds at refcount_inc_not_zero, there is a chance the ptrs value won't have been stored since refcount_set is unordered. Force a memory barrier here, I picked smp_mb, since we want it on all CPUs and it's write followed by a read. v2: use paired smp_rmb/smp_wmb. Cc: <stable@vger.kernel.org> Fixes: be55287 ("drm/nouveau/imem/nv50: embed nvkm_instobj directly into nv04_instobj") Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Danilo Krummrich <dakr@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240411011510.2546857-1-airlied@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Enric Balletbo i Serra and others added 30 commits June 13, 2018 16:16

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Merge tag 'v4.9.109' into 4.9-2.0.x-imx #27

Merge tag 'v4.9.109' into 4.9-2.0.x-imx #27

gibsson commented Jun 25, 2018

Merge tag 'v4.9.109' into 4.9-2.0.x-imx #27

Merge tag 'v4.9.109' into 4.9-2.0.x-imx #27

Conversation

gibsson commented Jun 25, 2018