Rigol DHOxxx oscilloscope Python library (unofficial)

Based completely on https://github.com/tspspi/pymso5000/tree/master by tspspi

A simple Python library and utility to control and query data from Rigol DHOxxx oscilloscopes. This library implements the Oscilloscope class from the pylabdevs package which exposes the public interface.

When retrieving sample point data from the scope, the number of points retrieved is set by the scope's memory depth.

The default memory depth of the scope is set to 10k points. This can be changed through the set_memory_depth() function

Alternatively this can be changed by accessing the following menus on the scope:

Click on any channel and click "Acquisition":

Change the memory depth:

Installing

There is a PyPi package that can be installed using

pip install pydho800

Simple example to fetch waveforms:

from pydho800.pydho800 import PYDHO800
from labdevices.oscilloscope import OscilloscopeRunMode

with PYDHO800(address = "10.0.0.123") as dho:
    print(f"Identify: {dho.identify()}")

    dho.set_channel_enable(0, True)
    dho.set_channel_enable(1, True)

    dho.set_channel_scale(0,.1)    # 100 mV/div
    dho.set_timebase_scale(100e-6) # 100 us/div

    # Set memory depth to 10 million samples
    tx_depth = dho.memory_depth_t.M_10M
    dho.set_memory_depth(tx_depth)

    # DHO914S/DHO924S specific for the signal generator
    signal_gen_waveform = dho.signal_gen_waveform_t.SINE
    dho.set_signal_gen_waveform(signal_gen_waveform)
    dho.set_signal_gen_amp(3.5)      # 3.5 Vpp
    dho.set_signal_gen_freq(1*10**6) # 1 MHz

    # Back to the oscilloscope
    dho.set_run_mode(OscilloscopeRunMode.RUN)
    dho.set_run_mode(OscilloscopeRunMode.STOP)

    data = dho.query_waveform((0, 1))
    print(data)

    import matplotlib.pyplot as plt
    plt.plot(data['x'], data['y0'], label = "Ch1")
    plt.plot(data['x'], data['y1'], label = "Ch2")

    # Note if only one channel were enabled, it would be accessed by:
    # plt.plot(data['x'], data['y'], label = "Ch1")

    plt.show()

Note that numpy usage is optional for this implementation. One can enable numpy support using useNumpy = True in the constructor.

Querying additional statistics

This module allows - via the pylabdevs base class to query additional statistics:

• mean Calculates the mean values and standard deviations
  • A single value for each channels mean at ["means"]["yN_avg"] and a single value for each standard deviation at ["means"]["yN_std"] where N is the channel number
• fft runs Fourier transform on all queried traces
  • The result is stored in ["fft"]["yN"] (complex values) and in ["fft"]["yN_real"] for the real valued Fourier transform. Again N is the channel number
• ifft runs inverse Fourier transform on all queried traces
  • Works as fft but runs the inverse Fourier transform and stores its result in ifft instead of fft
• correlate calculates the correlation between all queried waveform pairs.
  • The result of the correlations are stored in ["correlation"]["yNyM"] for the correlation between channels M and N
• autocorrelate performs calculation of the autocorrelation of each queried channel.
  • The result of the autocorrelation is stored in ["autocorrelation"]["yN"] for channel N

To request calculation of statistics pass the string for the desired statistic or a list of statistics to the stats parameter of query_waveform:

with DHO800(address = "10.0.0.123") as dho:
    data = dho.query_waveform((1,2), stats = [ 'mean', 'fft' ])

Get Measurement Data

The DHO800/900 has in-built measurement functions. This package release supports the 10 most common used functions:

• VPP: indicates the voltage value from the highest point to the lowest point of the waveform.
• RRPH: indicates the phase deviation between the threshold middle values of the rising edge of Source A and that of Source B.
• FFPH: indicates the phase deviation between the threshold middle values of the falling edge of Source A and that of Source B.
• VMIN: indicates the voltage value from the lowest point of the waveform to the GND.
• VMAX: indicates the voltage value from the highest point of the waveform to the GND.
• VRMS: indicates the root mean square value on the whole waveform or in the gating area.
• VAVG: indicates the root-mean-square value of the waveforms, with the DC component removed.
• OVER: indicates the ratio of the difference between the maximum value and the top value of the waveform to the amplitude value.
• FREQ: defined as the reciprocal of period.
• PER: defined as the time between the middle threshold points of two consecutive, like-polarity edges.

For more detailed information about :MEASure Commands see DHO Progamming Guide (Jul 2023) section 3.17

with DHO800(address = "10.0.0.123") as dho:
    # gets voltage peak to peak
    volt = float(dho.get_channel_measurement(type='VPP', channel=0))
    # gets phase from rising edge refchannel to rising edge channel
    phase_riserise = float(dho.get_channel_measurement(type='RRPH',channel=1, refchannel=0))

Supported methods

More documentation in progress ...

• identify()
• Connection management (when not using with context management):
  • connect()
  • disconnect()
• set_channel_enable(channel, enabled)
• is_channel_enabled(channel)
• set_sweep_mode(mode)
• get_sweep_mode()
• set_trigger_mode(mode)
• get_trigger_mode()
• force_trigger()
• set_timebase_mode(mode)
• get_timebase_mode()
• set_run_mode(mode)
• get_run_mode()
• set_timebase_scale(secondsPerDivision)
• get_timebase_scale()
• set_channel_coupling(channel, couplingMode)
• get_channel_coupling(channel)
• set_channel_probe_ratio(channel, ratio)
• get_channel_probe_ratio(channel)
• set_channel_scale(channel, scale)
• get_channel_scale(channel)
• set_channel_bandwidth(channel, scale)
• get_channel_bandwidth(channel)
• get_channel_measurement(type, channel[, refchannel])
• query_waveform(channel, stats = None)
• off()