Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

Sign up for GitHub

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

Jump to bottom

Majestic: Cannot start SDK #21

Open
akanouras opened this issue Feb 17, 2024 · 2 comments
Open

Majestic: Cannot start SDK #21

akanouras opened this issue Feb 17, 2024 · 2 comments

Comments

@akanouras
Copy link

akanouras commented Feb 17, 2024 •
edited

After using succesfully an OpenIPC Ultimate version from October 2023 for a few months, I tried to "Install update from Github". The installation of 2.4.02.17-ultimate went fine, with two problems however:

  1. wlan0 wasn't started after boot. Overcame this by adding ifup wlan0 to /etc/rc.local
  2. Majestic will not start, even with the default majestic.yaml

fw_printenv:

baseaddr=0x80600000
baudrate=115200
bootargs=mem=${osmem} rmem=${rmem} console=ttyS1,115200n8 panic=20 root=/dev/mtdblock3 rootfstype=squashfs init=/init mtdparts=${mtdparts} ${extras}
bootargsnfs=mem=${osmem} console=ttyS1,115200n8 panic=20 root=/dev/nfs rootfstype=nfs ip=${ipaddr}:::255.255.255.0::eth0 nfsroot=${serverip}:${nfsroot},v3,nolock rw ${extras}
bootargsubi=mem=${osmem} console=ttyS1,115200n8 panic=20 init=/init root=ubi0:rootfs rootfstype=ubifs ubi.mtd=3,2048 mtdparts=${mtdparts} ${extras}
bootcmd=setenv setargs setenv bootargs ${bootargs}; run setargs; sf probe 0; sf read ${baseaddr} 0x50000 0x300000; bootm ${baseaddr}
bootcmdnand=setenv setargs setenv bootargs ${bootargs}; run setargs; nand read ${baseaddr} 0x100000 0x300000; bootm ${baseaddr}
bootcmdnor=setenv setargs setenv bootargs ${bootargs}; run setargs; sf probe 0; sf read ${baseaddr} 0x50000 0x300000; bootm ${baseaddr}
bootcmdubi=setenv setargs setenv bootargs ${bootargsubi}; run setargs; nand read ${baseaddr} 0x100000 0x300000; bootm ${baseaddr}
bootdelay=1
bootnfs=setenv setargs setenv bootargs ${bootargsnfs}; run setargs; tftpboot ${baseaddr} uImage.${soc}; bootm ${baseaddr}
ethact=Jz4775-9161
ethaddr=00:00:23:34:45:66
extras=nogmac
gatewayip=192.168.1.1
ipaddr=192.168.1.10
loads_echo=1
mtdparts=jz_sfc:256k(boot),64k(env),3072k(kernel),10240k(rootfs),-(rootfs_data)
mtdpartsnand=setenv mtdparts jz_sfcnand:256k(boot),768k(wtf),3072k(kernel),10240k(rootfs),-(rootfs_data)
mtdpartsnor16m=setenv mtdparts jz_sfc:256k(boot),64k(env),3072k(kernel),10240k(rootfs),-(rootfs_data)
mtdpartsnor8m=setenv mtdparts jz_sfc:256k(boot),64k(env),2048k(kernel),5120k(rootfs),-(rootfs_data)
mtdpartsubi=setenv mtdparts jz_sfcnand:256k(boot),768k(wtf),3072k(kernel),-(ubi)
netmask=255.255.255.0
nfsroot=/srv/nfs/t31
osmem=40M
restore=n
rmem=24M@0x2800000
serverip=192.168.1.254
setnand=run mtdpartsubi; setenv bootcmd ${bootcmdubi}; saveenv; reset
setnor16m=run mtdpartsnor16m; setenv bootcmd ${bootcmdnor}; saveenv; reset
setnor8m=run mtdpartsnor8m; setenv bootcmd ${bootcmdnor}; saveenv; reset
soc=t31
stderr=serial
stdin=serial
stdout=serial
totalmem=64M
uknand=mw.b ${baseaddr} ff 1000000; tftpboot ${baseaddr} uImage.${soc} ; nand erase 0x100000 0x300000; nand write ${baseaddr} 0x100000 0x300000
uknor16m=mw.b ${baseaddr} ff 1000000; tftpboot ${baseaddr} uImage.${soc} ; sf probe 0; sf erase 0x50000 0x300000; sf write ${baseaddr} 0x50000 ${filesize}
uknor8m=mw.b ${baseaddr} ff 1000000; tftpboot ${baseaddr} uImage.${soc} ; sf probe 0; sf erase 0x50000 0x200000; sf write ${baseaddr} 0x50000 ${filesize}
urnand=mw.b ${baseaddr} ff 1000000; tftpboot ${baseaddr} rootfs.ubi.${soc} ; nand erase 0x400000 0x7c00000; nand write ${baseaddr} 0x400000 ${filesize}
urnor16m=mw.b ${baseaddr} ff 1000000; tftpboot ${baseaddr} rootfs.squashfs.${soc} ; sf probe 0; sf erase 0x350000 0xa00000; sf write ${baseaddr} 0x350000 ${filesize}
urnor8m=mw.b ${baseaddr} ff 1000000; tftpboot ${baseaddr} rootfs.squashfs.${soc} ; sf probe 0; sf erase 0x250000 0x500000; sf write ${baseaddr} 0x250000 ${filesize}
wlanpass=<<redacted>>
wlanssid=<<redacted>>
sensor=jxq03p

Boot log:

U-Boot SPL 2013.07-g2762b69-dirty (Apr 19 2023 - 22:04:12)
Timer init
CLK stop
PLL init
pll_init:366
pll_cfg.pdiv = 10, pll_cfg.h2div = 5, pll_cfg.h0div = 5, pll_cfg.cdiv = 1, pll_cfg.l2div = 2
nf=118 nr = 1 od0 = 1 od1 = 2
cppcr is 07605100
CPM_CPAPCR 0750510d
nf=84 nr = 1 od0 = 1 od1 = 2
cppcr is 05405100
CPM_CPMPCR 07d0590d
nf=100 nr = 1 od0 = 1 od1 = 2
cppcr is 06405100
CPM_CPVPCR 0640510d
cppcr 0x9a773310
apll_freq 1404000000 
mpll_freq 1000000000 
vpll_freq = 1200000000
ddr sel mpll, cpu sel apll
ddrfreq 500000000
cclk  1404000000
l2clk 702000000
h0clk 200000000
h2clk 200000000
pclk  100000000
CLK init
SDRAM init
sdram init start
ddr_inno_phy_init ..!
phy reg = 0x00000007, CL = 0x00000007
ddr_inno_phy_init ..! 11:  00000004
ddr_inno_phy_init ..! 22:  00000006
ddr_inno_phy_init ..! 33:  00000006
REG_DDR_LMR: 00000210
REG_DDR_LMR: 00000310
REG_DDR_LMR: 00000110
REG_DDR_LMR, MR0: 00f73011
T31_0x5: 00000007
T31_0x15: 0000000c
T31_0x4: 00000000
T31_0x14: 00000002
INNO_TRAINING_CTRL 1: 00000000
INNO_TRAINING_CTRL 2: 000000a1
T31_cc: 00000003
INNO_TRAINING_CTRL 3: 000000a0
T31_118: 0000003c
T31_158: 0000003c
T31_190: 00000020
T31_194: 0000001f
jz-04 :  0x00000051 
jz-08 :  0x000000a0 
jz-28 :  0x00000024 
DDR PHY init OK
INNO_DQ_WIDTH   :00000003
INNO_PLL_FBDIV  :00000014
INNO_PLL_PDIV   :00000005
INNO_MEM_CFG    :00000051
INNO_PLL_CTRL   :00000018
INNO_CHANNEL_EN :0000000d
INNO_CWL        :00000006
INNO_CL         :00000007
DDR Controller init
DDRC_STATUS         0x80000001
DDRC_CFG            0x0a288a40
DDRC_CTRL           0x0000011c
DDRC_LMR            0x00400008
DDRC_DLP            0x00000000
DDRC_TIMING1        0x040e0806
DDRC_TIMING2        0x02170707
DDRC_TIMING3        0x2007051e
DDRC_TIMING4        0x1a240031
DDRC_TIMING5        0xff060405
DDRC_TIMING6        0x32170505
DDRC_REFCNT         0x00f26901
DDRC_MMAP0          0x000020fc
DDRC_MMAP1          0x00002400
DDRC_REMAP1         0x03020d0c
DDRC_REMAP2         0x07060504
DDRC_REMAP3         0x0b0a0908
DDRC_REMAP4         0x0f0e0100
DDRC_REMAP5         0x13121110
DDRC_AUTOSR_EN      0x00000000
sdram init finished
SDRAM init ok
board_init_r
image entry point: 0x80100000


U-Boot 2013.07-g2762b69-dirty (Apr 19 2023 - 22:04:12)

Board: ISVP (Ingenic XBurst T31 SoC)
DRAM:  64 MiB
Top of RAM usable for U-Boot at: 84000000
Reserving 475k for U-Boot at: 83f88000
Reserving 32832k for malloc() at: 81f78000
Reserving 32 Bytes for Board Info at: 81f77fe0
Reserving 124 Bytes for Global Data at: 81f77f64
Reserving 256k for boot params() at: 81f37f64
Stack Pointer at: 81f37f48
Now running in RAM - U-Boot at: 83f88000
MMC:   msc: 0
the manufacturer 1c
SF: Detected EN25QH128A

In:    serial
Out:   serial
Err:   serial
gpio_request[hichip_mmc_enable] = 62
Net:   ====>phy 0:0x0-0x0 found
SPEED:0, DUPLEX:0
Jz4775-9161
Autoupdate... 
Press Ctrl-c to abort autoboot... 1 
the manufacturer 1c
SF: Detected EN25QH128A

--->probe spend 4 ms
SF: 3145728 bytes @ 0x50000 Read: OK
--->read spend 1010 ms
## Booting kernel from Legacy Image at 80600000 ...
   Image Name:   Linux-3.10.14__isvp_swan_1.0__-t
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1879983 Bytes = 1.8 MiB
   Load Address: 80010000
   Entry Point:  803fe550
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.14__isvp_swan_1.0__ (runner@fv-az847-865) (buildroot-gcc-12.3.0) #2 PREEMPT Sat Feb 17 11:39:06 UTC 2024
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 RESET ERROR PC:801BE684
[    0.000000] [<801be684>] __delay+0x4/0x10
[    0.000000] CPU0 revision is: 00d00100 (Ingenic Xburst)
[    0.000000] FPU revision is: 00b70000
[    0.000000] CCLK:1404MHz L2CLK:702Mhz H0CLK:250MHz H2CLK:250Mhz PCLK:125Mhz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 0055e000 @ 00010000 (usable)
[    0.000000]  memory: 00032000 @ 0056e000 (usable after init)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 02800000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x027fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x027fffff]
[    0.000000] Primary instruction cache 32kB, 8-way, VIPT, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 8-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] pls check processor_id[0x00d00100],sc_jz not support!
[    0.000000] MIPS secondary cache 128kB, 8-way, linesize 32 bytes.
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 10160
[    0.000000] Kernel command line: mem=40M rmem=24M@0x2800000 console=ttyS1,115200n8 panic=20 root=/dev/mtdblock3 rootfstype=squashfs init=/init mtdparts=jz_sfc:256k(boot),64k(env),3072k(kernel),10240k(rootfs),-(rootfs_data) nogmac
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 34192k/40960k available (4076k kernel code, 6768k reserved, 1417k data, 200k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:358
[    0.000000] clockevents_config_and_register success.
[    0.000015] Calibrating delay loop... 1397.55 BogoMIPS (lpj=6987776)
[    0.037793] pid_max: default: 32768 minimum: 301
[    0.042652] Mount-cache hash table entries: 512
[    0.047581] Initializing cgroup subsys debug
[    0.051838] Initializing cgroup subsys freezer
[    0.057924] devtmpfs: initialized
[    0.062746] regulator-dummy: no parameters
[    0.067133] NET: Registered protocol family 16
[    0.074900] Skipping GMAC GPIO setup
[    0.097916] bio: create slab <bio-0> at 0
[    0.108494] jz-dma jz-dma: JZ SoC DMA initialized
[    0.114346] usbcore: registered new interface driver usbfs
[    0.120400] usbcore: registered new interface driver hub
[    0.126196] usbcore: registered new device driver usb
[    0.131576]  (null): set:311  hold:312 dev=125000000 h=625 l=625
[    0.139488] Switching to clocksource jz_clocksource
[    0.147016] jz-dwc2 jz-dwc2: cgu clk gate get error
[    0.151895] DWC IN OTG MODE
[    0.155695] dwc2 dwc2: Keep PHY ON
[    0.159064] dwc2 dwc2: Using Buffer DMA mode
[    0.163392] dwc2 dwc2: Core Release: 3.00a
[    0.167775] dwc2 dwc2: DesignWare USB2.0 High-Speed Host Controller
[    0.174070] dwc2 dwc2: new USB bus registered, assigned bus number 1
[    0.181540] hub 1-0:1.0: USB hub found
[    0.185381] hub 1-0:1.0: 1 port detected
[    0.189389] dwc2 dwc2: DWC2 Host Initialized
[    0.193931] NET: Registered protocol family 2
[    0.198833] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.205893] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.212266] TCP: Hash tables configured (established 512 bind 512)
[    0.218604] TCP: reno registered
[    0.221800] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.227762] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.234258] NET: Registered protocol family 1
[    0.238870] RPC: Registered named UNIX socket transport module.
[    0.244850] RPC: Registered udp transport module.
[    0.249565] RPC: Registered tcp transport module.
[    0.254333] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.261496] freq_udelay_jiffys[0].max_num = 10
[    0.265988] cpufreq 	udelay 	loops_per_jiffy	
[    0.270344] dwc2 dwc2: ID PIN CHANGED!
[    0.274172] 12000	 59724	 59724	
[    0.277424] 24000	 119449	 119449	
[    0.280842] 60000	 298622	 298622	
[    0.284286] 120000	 597245	 597245	
[    0.287903] 200000	 995409	 995409	
[    0.291354] 300000	 1493114	 1493114	
[    0.295170] 600000	 2986229	 2986229	
[    0.298800] 792000	 3941822	 3941822	
[    0.302508] 1008000	 5016864	 5016864	
[    0.306338] 1200000	 5972458	 5972458	
[    0.320239] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.327421] jffs2: version 2.2. © 2001-2006 Red Hat, Inc.
[    0.333503] msgmni has been set to 66
[    0.338498] io scheduler noop registered
[    0.342422] io scheduler cfq registered (default)
[    0.354502] jz-uart.1: ttyS1 at MMIO 0x10031000 (irq = 58) is a uart1
[    0.361941] console [ttyS1] enabled, bootconsole disabled
[    0.361941] console [ttyS1] enabled, bootconsole disabled
[    0.381912] brd: module loaded
[    0.390002] loop: module loaded
[    0.393487] logger: created 256K log 'log_main'
[    0.400461] jz TCU driver register completed
[    0.406103] the id code = 1c7018, the flash name is EN25QH128A
[    0.412126] JZ SFC Controller for SFC channel 0 driver register
[    0.418445] 5 cmdlinepart partitions found on MTD device jz_sfc
[    0.424639] Creating 5 MTD partitions on "jz_sfc":
[    0.429594] 0x000000000000-0x000000040000 : "boot"
[    0.435638] 0x000000040000-0x000000050000 : "env"
[    0.441593] 0x000000050000-0x000000350000 : "kernel"
[    0.447914] 0x000000350000-0x000000d50000 : "rootfs"
[    0.454106] 0x000000d50000-0x000001000000 : "rootfs_data"
[    0.460852] SPI NOR MTD LOAD OK
[    0.464275] JZ GMAC disabled
[    0.467462] STA : @@@@@@ rtusb init rt2870 --->
[    0.472314] usbcore: registered new interface driver rt2870
[    0.478384] usbcore: registered new interface driver asix
[    0.483974] i2c /dev entries driver
[    0.488921] wait stable.[289][cgu_msc0]
[    0.492888] jzmmc_v1.2 jzmmc_v1.2.0: vmmc regulator missing
[    0.499038] jzmmc_v1.2 jzmmc_v1.2.0: register success!
[    0.504520] jzmmc_v1.2 jzmmc_v1.2.1: vmmc regulator missing
[    0.510562] jzmmc_v1.2 jzmmc_v1.2.1: register success!
[    0.516500] ipip: IPv4 over IPv4 tunneling driver
[    0.521960] TCP: cubic registered
[    0.526544] NET: Registered protocol family 10
[    0.531922] NET: Registered protocol family 17
[    0.537834] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    0.545415] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    0.556511] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    0.567604] devtmpfs: mounted
[    0.571004] Freeing unused kernel memory: 200K (8056e000 - 805a0000)
[    0.994406] jzmmc_v1.2 jzmmc_v1.2.0: card inserted, state=0
[    1.242675] jffs2: notice: (447) jffs2_build_xattr_subsystem: complete building xattr subsystem, 87 of xdatum (0 unchecked, 87 orphan) and 87 of xref (0 dead, 87 orphan) found.
Timezone env variable not found, using system default.
Sat Feb 17 13:45:23 EET 2024
Starting automatic LED control: OK
Seeding 2048 bits and crediting
Saving 2048 bits of creditable seed for next boot
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
Loading modules:Starting rngd: OK
Customizer script not present...
Starting mdev...
Starting network...
ip: SIOCGIFINDEX: No such device
Starting ntpd: OK
Starting dropbear sshd: OK
Production mode
Starting httpd: OK
Starting mini-snmpd: DISABLED, OK
Starting telnetd: DISABLED, OK
Starting crond: OK

Loading of kernel modules...
modprobe: can't load module sinfo (extra/sinfo.ko): No such file or directory
err: insmod sinfo
exit
Zerotier-One service is disabled in /etc/webui/zerotier.conf.
Starting telegram-bot.sh: OK
Successfully initialized wpa_supplicant
rfkill: Cannot open RFKILL control device
nl80211: Could not re-add multicast membership for vendor events: -2 (Interrupted system call)
udhcpc: started, v1.36.1
udhcpc: broadcasting discover
udhcpc: broadcasting discover
udhcpc: broadcasting discover
udhcpc: broadcasting select for 10.0.4.40, server 10.0.4.1
udhcpc: lease of 10.0.4.40 obtained from 10.0.4.1, lease time 1800
deleting routers
adding dns 10.0.4.1
ntpd: setting time to 2024-02-17 15:03:51.785317 (offset +11901.655439s)
ingenic: Loading video system has started...
Starting majestic: OK

Welcome to OpenIPC
mjsxj03hl-2nd-floor login:

logread output:

Feb 17 13:45:23 mjsxj03hl-2nd-floor syslog.info syslogd started: BusyBox v1.36.1
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.notice kernel: klogd started: BusyBox v1.36.1 (2024-02-17 11:33:17 UTC)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] Initializing cgroup subsys cpu
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] Initializing cgroup subsys cpuacct
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.notice kernel: [    0.000000] Linux version 3.10.14__isvp_swan_1.0__ (runner@fv-az847-865) (buildroot-gcc-12.3.0) #2 PREEMPT Sat Feb 17 11:39:06 UTC 2024
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] bootconsole [early0] enabled
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.000000] CPU0 RESET ERROR PC:801BE684
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.000000] [<801be684>] __delay+0x4/0x10
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] CPU0 revision is: 00d00100 (Ingenic Xburst)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] FPU revision is: 00b70000
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.000000] cgu_get_rate, parent = 1404000000, rate = 0, m = 129, n = 255, reg val = 0x081000ff
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.000000] cgu_get_rate, parent = 1404000000, rate = 0, m = 129, n = 255, reg val = 0x081000ff
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.000000] CCLK:1404MHz L2CLK:702Mhz H0CLK:250MHz H2CLK:250Mhz PCLK:125Mhz
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] Determined physical RAM map:
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000]  memory: 0055e000 @ 00010000 (usable)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000]  memory: 00032000 @ 0056e000 (usable after init)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] User-defined physical RAM map:
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000]  memory: 02800000 @ 00000000 (usable)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] Initrd not found or empty - disabling initrd
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.000000] Zone ranges:
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.000000]   Normal   [mem 0x00000000-0x027fffff]
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.000000] Movable zone start for each node
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.000000] Early memory node ranges
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.000000]   node   0: [mem 0x00000000-0x027fffff]
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.000000] On node 0 totalpages: 10240
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.000000] free_area_init_node: node 0, pgdat 80568130, node_mem_map 81000000
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.000000]   Normal zone: 80 pages used for memmap
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.000000]   Normal zone: 0 pages reserved
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.000000]   Normal zone: 10240 pages, LIFO batch:1
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.000000] Primary instruction cache 32kB, 8-way, VIPT, linesize 32 bytes.
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.000000] Primary data cache 32kB, 8-way, VIPT, no aliases, linesize 32 bytes
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.000000] pls check processor_id[0x00d00100],sc_jz not support!
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.000000] MIPS secondary cache 128kB, 8-way, linesize 32 bytes.
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0 
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 10160
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.notice kernel: [    0.000000] Kernel command line: mem=40M rmem=24M@0x2800000 console=ttyS1,115200n8 panic=20 root=/dev/mtdblock3 rootfstype=squashfs init=/init mtdparts=jz_sfc:256k(boot),64k(env),3072k(kernel),10240k(rootfs),-(rootfs_data) no
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] Memory: 34192k/40960k available (4076k kernel code, 6768k reserved, 1417k data, 200k init, 0k highmem)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] Preemptible hierarchical RCU implementation.
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000000] NR_IRQS:358
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.000000] clockevents_config_and_register success.
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.000015] Calibrating delay loop... 1397.55 BogoMIPS (lpj=6987776)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.037793] pid_max: default: 32768 minimum: 301
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.042652] Mount-cache hash table entries: 512
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.047581] Initializing cgroup subsys debug
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.051838] Initializing cgroup subsys freezer
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.057924] devtmpfs: initialized
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.062746] regulator-dummy: no parameters
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.067133] NET: Registered protocol family 16
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.074900] Skipping GMAC GPIO setup
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.079105] set gpio strength: 32-2
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.079116] set gpio strength: 33-2set gpio strength: 34-2
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.079126] set gpio strength: 35-2set gpio strength: 36-2
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.079135] set gpio strength: 37-2set gpio pull: 59-90
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.097916] bio: create slab <bio-0> at 0
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.108494] jz-dma jz-dma: JZ SoC DMA initialized
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.114346] usbcore: registered new interface driver usbfs
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.120400] usbcore: registered new interface driver hub
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.126196] usbcore: registered new device driver usb
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.131576]  (null): set:311  hold:312 dev=125000000 h=625 l=625
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.139488] Switching to clocksource jz_clocksource
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.146987] dwc2 otg probe start
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.warn kernel: [    0.147016] jz-dwc2 jz-dwc2: cgu clk gate get error
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.151895] DWC IN OTG MODE
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.155695] dwc2 dwc2: Keep PHY ON
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.159064] dwc2 dwc2: Using Buffer DMA mode
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.163392] dwc2 dwc2: Core Release: 3.00a
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.167775] dwc2 dwc2: DesignWare USB2.0 High-Speed Host Controller
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.174070] dwc2 dwc2: new USB bus registered, assigned bus number 1
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.181540] hub 1-0:1.0: USB hub found
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.185381] hub 1-0:1.0: 1 port detected
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info sysctl: * Applying /etc/sysctl.conf ...
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.189389] dwc2 dwc2: DWC2 Host Initialized
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.debug kernel: [    0.193677] dwc2 otg probe success
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.193931] NET: Registered protocol family 2
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.198833] TCP established hash table entries: 512 (order: 0, 4096 bytes)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.205893] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.212266] TCP: Hash tables configured (established 512 bind 512)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.218604] TCP: reno registered
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.221800] UDP hash table entries: 256 (order: 0, 4096 bytes)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.227762] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.234258] NET: Registered protocol family 1
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.238870] RPC: Registered named UNIX socket transport module.
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.244850] RPC: Registered udp transport module.
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.249565] RPC: Registered tcp transport module.
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.254333] RPC: Registered tcp NFSv4.1 backchannel transport module.
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.261496] freq_udelay_jiffys[0].max_num = 10
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.265988] cpufreq 	udelay 	loops_per_jiffy	
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.270344] dwc2 dwc2: ID PIN CHANGED!
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.274172] 12000	 59724	 59724	
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.277424] 24000	 119449	 119449	
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.280842] 60000	 298622	 298622	
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.284286] 120000	 597245	 597245	
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.287903] 200000	 995409	 995409	
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.291354] 300000	 1493114	 1493114	
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.295170] 600000	 2986229	 2986229	
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.298800] 792000	 3941822	 3941822	
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.302508] 1008000	 5016864	 5016864	
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.306338] 1200000	 5972458	 5972458	
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.320239] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.327421] jffs2: version 2.2. © 2001-2006 Red Hat, Inc.
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.333503] msgmni has been set to 66
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.338498] io scheduler noop registered
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.342422] io scheduler cfq registered (default)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.354502] jz-uart.1: ttyS1 at MMIO 0x10031000 (irq = 58) is a uart1
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.361941] console [ttyS1] enabled, bootconsole disabled
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info sysctl: kernel.printk = 3 3 1 3
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.381912] brd: module loaded
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.390002] loop: module loaded
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.393487] logger: created 256K log 'log_main'
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.400461] jz TCU driver register completed
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.406103] the id code = 1c7018, the flash name is EN25QH128A
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.412126] JZ SFC Controller for SFC channel 0 driver register
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.notice kernel: [    0.418445] 5 cmdlinepart partitions found on MTD device jz_sfc
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.notice kernel: [    0.424639] Creating 5 MTD partitions on "jz_sfc":
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.notice kernel: [    0.429594] 0x000000000000-0x000000040000 : "boot"
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.notice kernel: [    0.435638] 0x000000040000-0x000000050000 : "env"
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.notice kernel: [    0.441593] 0x000000050000-0x000000350000 : "kernel"
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.notice kernel: [    0.447914] 0x000000350000-0x000000d50000 : "rootfs"
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.notice kernel: [    0.454106] 0x000000d50000-0x000001000000 : "rootfs_data"
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.460852] SPI NOR MTD LOAD OK
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.464275] JZ GMAC disabled
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.467462] STA : @@@@@@ rtusb init rt2870 --->
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.472314] usbcore: registered new interface driver rt2870
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.478384] usbcore: registered new interface driver asix
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.483974] i2c /dev entries driver
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.488921] wait stable.[289][cgu_msc0]
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.warn kernel: [    0.492888] jzmmc_v1.2 jzmmc_v1.2.0: vmmc regulator missing
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.499038] jzmmc_v1.2 jzmmc_v1.2.0: register success!
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.warn kernel: [    0.504520] jzmmc_v1.2 jzmmc_v1.2.1: vmmc regulator missing
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.510562] jzmmc_v1.2 jzmmc_v1.2.1: register success!
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.516500] ipip: IPv4 over IPv4 tunneling driver
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.521960] TCP: cubic registered
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.526544] NET: Registered protocol family 10
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.531922] NET: Registered protocol family 17
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.537834] input: gpio-keys as /devices/platform/gpio-keys/input/input0
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    0.545415] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.556511] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.567604] devtmpfs: mounted
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    0.571004] Freeing unused kernel memory: 200K (8056e000 - 805a0000)
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.notice kernel: [    0.994406] jzmmc_v1.2 jzmmc_v1.2.0: card inserted, state=0
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.notice kernel: [    1.242675] jffs2: notice: (447) jffs2_build_xattr_subsystem: complete building xattr subsystem, 87 of xdatum (0 unchecked, 87 orphan) and 87 of xref (0 dead, 87 orphan) found.
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err sysctl: sysctl: error: 'net.core.bpf_jit_enable' is an unknown key
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    1.666209] exFAT: Version 1.2.9
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.info kernel: [    1.737147] cfg80211: Calling CRDA to update world regulatory domain
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.warn kernel: [    2.116255] mmc0: host doesn't support card's voltages
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    2.116271] mmc0: error -22 whilst initialising SDIO card
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.warn kernel: [    2.134947] mmc0: host doesn't support card's voltages
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    2.134963] mmc0: error -22 whilst initialising MMC card
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.warn kernel: [    2.257115] mmc0: host doesn't support card's voltages
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    2.257131] mmc0: error -22 whilst initialising SDIO card
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.warn kernel: [    2.275457] mmc0: host doesn't support card's voltages
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    2.275474] mmc0: error -22 whilst initialising MMC card
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    2.322899] RTL871X: module init start
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    2.322913] RTL871X: rtl8189ftv v4.3.24.7_21113.20170208.nova.1.02
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    2.322919] RTL871X: build time: Aug 14 2020 13:46:20
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    2.322931] wlan power on
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    2.334811] RTL871X: module init ret=0
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.warn kernel: [    2.398313] mmc0: host doesn't support card's voltages
Feb 17 13:45:23 mjsxj03hl-2nd-floor kern.err kernel: [    2.398329] mmc0: error -22 whilst initialising SDIO card
Feb 17 13:45:24 mjsxj03hl-2nd-floor kern.warn kernel: [    2.415516] mmc0: host doesn't support card's voltages
Feb 17 13:45:24 mjsxj03hl-2nd-floor kern.err kernel: [    2.415532] mmc0: error -22 whilst initialising MMC card
Feb 17 13:45:24 mjsxj03hl-2nd-floor kern.warn kernel: [    2.457007] mmc1: card claims to support voltages below the defined range. These will be ignored.
Feb 17 13:45:24 mjsxj03hl-2nd-floor kern.info kernel: [    2.525214] mmc1: new SDIO card at address 0001
Feb 17 13:45:24 mjsxj03hl-2nd-floor kern.err kernel: [    2.528574] RTL871X: ++++++++rtw_drv_init: vendor=0x024c device=0xf179 class=0x07
Feb 17 13:45:24 mjsxj03hl-2nd-floor kern.err kernel: [    2.560227] RTL871X: HW EFUSE
Feb 17 13:45:24 mjsxj03hl-2nd-floor kern.err kernel: [    2.560257] RTL871X: hal_com_config_channel_plan chplan:0x20
Feb 17 13:45:24 mjsxj03hl-2nd-floor kern.err kernel: [    2.681338] RTL871X: rtw_regsty_chk_target_tx_power_valid return _FALSE for band:0, path:0, rs:0, t:-1
Feb 17 13:45:24 mjsxj03hl-2nd-floor kern.err kernel: [    2.682372] RTL871X: rtw_ndev_init(wlan0) if1 mac_addr=58:b6:23:26:1a:a0
Feb 17 13:45:24 mjsxj03hl-2nd-floor authpriv.info dropbear[588]: Running in background
Feb 17 13:45:24 mjsxj03hl-2nd-floor cron.info crond[605]: crond (busybox 1.36.1) started, log level 8
Feb 17 13:45:25 mjsxj03hl-2nd-floor kern.info kernel: [    4.007697] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Feb 17 13:45:27 mjsxj03hl-2nd-floor kern.emerg kernel: [    5.689177] RTL871X: rtw_set_802_11_connect(wlan0)  fw_state=0x00000008
Feb 17 13:45:27 mjsxj03hl-2nd-floor kern.emerg kernel: [    5.716576] RTL871X: start auth
Feb 17 13:45:27 mjsxj03hl-2nd-floor kern.emerg kernel: [    5.719544] RTL871X: auth success, start assoc
Feb 17 13:45:27 mjsxj03hl-2nd-floor kern.emerg kernel: [    5.722526] RTL871X: assoc success
Feb 17 13:45:27 mjsxj03hl-2nd-floor kern.info kernel: [    5.722626] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Feb 17 13:45:27 mjsxj03hl-2nd-floor kern.emerg kernel: [    5.744502] RTL871X: recv eapol packet
Feb 17 13:45:27 mjsxj03hl-2nd-floor kern.emerg kernel: [    5.745744] RTL871X: send eapol packet
Feb 17 13:45:27 mjsxj03hl-2nd-floor kern.emerg kernel: [    5.748297] RTL871X: recv eapol packet
Feb 17 13:45:27 mjsxj03hl-2nd-floor kern.emerg kernel: [    5.748636] RTL871X: send eapol packet
Feb 17 13:45:27 mjsxj03hl-2nd-floor kern.emerg kernel: [    5.749001] RTL871X: set pairwise key camid:4, addr:8c:de:f9:73:48:06, kid:0, type:AES
Feb 17 13:45:27 mjsxj03hl-2nd-floor kern.emerg kernel: [    5.749646] RTL871X: set group key camid:5, addr:8c:de:f9:73:48:06, kid:2, type:AES
Feb 17 17:03:51 mjsxj03hl-2nd-floor daemon.info ingenic: Loading video system has started...
Feb 17 17:03:51 mjsxj03hl-2nd-floor daemon.info : starting pid 796, tty '/dev/console': '/sbin/getty -L console 0 vt100 '
Feb 17 17:03:52 mjsxj03hl-2nd-floor user.info majestic[797]: Majestic Lite for Ingenic, version master+80573c2, built on 2024-02-17
Feb 17 17:03:52 mjsxj03hl-2nd-floor user.info majestic[797]: HTTP server started on :::80
Feb 17 17:03:52 mjsxj03hl-2nd-floor user.info majestic[797]: Loading main configuration: /etc/majestic.yaml
Feb 17 17:03:52 mjsxj03hl-2nd-floor user.info majestic[797]: Using /etc/sensor/jxq03p.yaml as sensor config
Feb 17 17:03:52 mjsxj03hl-2nd-floor user.err majestic[797]: IMP_ISP_Open() failed
Feb 17 17:03:52 mjsxj03hl-2nd-floor user.err majestic[797]: imp_system_init() failed
Feb 17 17:03:52 mjsxj03hl-2nd-floor user.err majestic[797]: Cannot start SDK
Feb 17 17:04:22 mjsxj03hl-2nd-floor cron.info crond[605]: time disparity of 198 minutes detected
Feb 17 17:09:06 mjsxj03hl-2nd-floor authpriv.info dropbear[6132]: Child connection from 10.0.4.42:52186
Feb 17 17:09:06 mjsxj03hl-2nd-floor authpriv.notice dropbear[6132]: Pubkey auth succeeded for 'root' with ssh-rsa key SHA256:ybFqKr4rRcgV+kXMAZxuGk/oj8B2ItL6gczp9ofnGsE from 10.0.4.42:52186

My apologies if I'm missing something obvious.
@akanouras
Copy link
Author

Small update:

Upgraded using sysupgrade --url=https://github.com/OpenIPC/builder/releases/download/latest/t31_lite_xiaomi-mjsxj03hl-nor.tgz -k -r -z:

  1. ifup wlan0 is not needed in /etc/rc.local any more
  2. Majestic still fails with "Cannot start SDK"

@akanouras
Copy link
Author

Same message with 2.4.03.05-lite.

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
Assignees
No one assigned
Labels
None yet
Milestone
No milestone
Development

No branches or pull requests
1 participant
@akanouras