ttgo keeps rebooting, why? #462
Replies: 4 comments 4 replies
-
|
I'm on a fone, but look at src/screen.cc:403
You'll find a throw or dcheck or abort or dinner other kind of internal
consistency check that's falling.
Not to be jaded, but Do whatever it takes to make that not fail. 😉
If you don't have a. Screen, for example, turning off screen may be wise.
(Actually,. Even if you do,. It's not a bad troubleshooting step.)
…On Tue, Oct 17, 2023, 2:19 PM heidepiek ***@***.***> wrote:
Been tinkering with the nightdriverstrip software, and was testing out my
ttgo board. I used line in platformio: [platformio]
default_envs = ttgo
I build it:
build.odt
<https://github.com/PlummersSoftwareLLC/NightDriverStrip/files/12938228/build.odt>
And uploaded it:
upload.odt
<https://github.com/PlummersSoftwareLLC/NightDriverStrip/files/12938369/upload.odt>
Then the ttgo keeps rebooting. Why does the board keeps rebooting? Does it
have to do with the the 4mb flash?
Thats the board im using. I know that there are 16mb flash boards. But i
dont have that board. Dave has had the ttgo board running with the
spectrum analyzer. I still havent managed to do that on the ttgo! I know
dave recommends the dev_m5stick-c-plus, and that works like a charm. But it
would be nice to have that also running on a ttgo. Maybe it`s because off
the flash memory.
I get this in the serial:
Executing task: C:\Users\Eigenaar.platformio\penv\Scripts\platformio.exe
device monitor --port COM6
Please build project in debug configuration to get more details about an
exception.
See https://docs.platformio.org/page/projectconf/build_configurations.html
--- Terminal on COM6 | 115200 8-N-1
--- Available filters and text transformations: colorize, debug, default,
direct, esp32_exception_decoder, hexlify, log2file, nocontrol, printable,
send_on_enter, time
--- More details at https://bit.ly/pio-monitor-filters
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H
ets Jul 29 2019 12:21:46
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
>> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
JSON, using defaults
(W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
(W) (setup)(C1) Starting ImprovSerial for ESP32
[ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
directory
(W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
"heidepiek", "********"
E (812) gpio: GPIO can only be used as input mode
[ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
E (823) gpio: GPIO can only be used as input mode
[ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
(W) (setup)(C1) Creating TFT Screen
(W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
(I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
(I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
FastLED.
(W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
35040 bytes...
(W) (InitEffectsManager)(C1) InitEffectsManager...
(I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
(I) (InitEffectsManager)(C1) Creating EffectManager using default effects
Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
(W)
(W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
Launching Screen Thread. Mem: 142704, LargestBlk: 106484, PSRAM Free: 0/0,
>> Launching Audio Thread. Mem: 139560, LargestBlk: 102388, PSRAM Free:
0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
Launching Remote Thread. Mem: 135024, LargestBlk: 98292, PSRAM Free: 0/0,
(W) (begin)(C1) Remote Control Decoding Started
Launching Network Thread. Mem: 127844, LargestBlk: 90100, PSRAM Free: 0/0,
[ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
Error starting mDNS
Launching ColorData Thread. Mem: 119276, LargestBlk: 81908, PSRAM Free:
0/0, >> Launching Socket Thread. Mem: 116340, LargestBlk: 77812, PSRAM
Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
------------------------------
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
Exception -
(E) (TerminateHandler)(C0)
-------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C0) ------------------------------------------I)
(PrintOutputHeader)(C0)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 111868, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 <#1>
0x4009011d:0x3ffe6840 in esp_system_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 <#2>
0x40095799:0x3ffe6860 in abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 <#3>
0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
*)()) at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 <#4>
0x40191ace:0x3ffe6900 in std::terminate() at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 <#5>
0x40191a0f:0x3ffe6920 in __cxa_throw at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 <#6>
0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
(discriminator 4) #7
<#7>
0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2146) esp_core_dump_flash: Core dump flash config is corrupted!
CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum���ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
>> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
JSON, using defaults
(W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
(W) (setup)(C1) Starting ImprovSerial for ESP32
[ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
directory
(W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
"heidepiek", "********"
E (812) gpio: GPIO can only be used as input mode
[ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
E (823) gpio: GPIO can only be used as input mode
[ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
(W) (setup)(C1) Creating TFT Screen
(W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
(I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
(I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
FastLED.
(W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
35040 bytes...
(W) (InitEffectsManager)(C1) InitEffectsManager...
(I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
(I) (InitEffectsManager)(C1) Creating EffectManager using default effects
Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
(W)
(W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
Launching Screen Thread. Mem: 142716, LargestBlk: 106484, PSRAM Free: 0/0,
>> Launching Audio Thread. Mem: 139572, LargestBlk: 102388, PSRAM Free:
0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
Launching Remote Thread. Mem: 135036, LargestBlk: 98292, PSRAM Free: 0/0,
(W) (begin)(C1) Remote Control Decoding Started
Launching Network Thread. Mem: 127856, LargestBlk: 90100, PSRAM Free: 0/0,
[ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
Error starting mDNS
Launching ColorData Thread. Mem: 119288, LargestBlk: 81908, PSRAM Free:
0/0, >> Launching Socket Thread. Mem: 116352, LargestBlk: 77812, PSRAM
Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
------------------------------
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
Exception -
(E) (TerminateHandler)(C0)
-------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
I) (PrintOutputHeader)(C0) NightDriverStrip
-------------------(I)
(I) (PrintOutputHeader)(C0)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 111880, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 <#1>
0x4009011d:0x3ffe6840 in esp_system_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 <#2>
0x40095799:0x3ffe6860 in abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 <#3>
0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
*)()) at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 <#4>
0x40191ace:0x3ffe6900 in std::terminate() at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 <#5>
0x40191a0f:0x3ffe6920 in __cxa_throw at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 <#6>
0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
(discriminator 4) #7
<#7>
0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2136) esp_core_dump_flash: Core dump flash config is corrupted!
CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
ets Jul 29 2019 12:21:46
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
>> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
JSON, using defaults
(W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
(W) (setup)(C1) Starting ImprovSerial for ESP32
[ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
directory
(W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
"heidepiek", "********"
E (812) gpio: GPIO can only be used as input mode
[ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
E (823) gpio: GPIO can only be used as input mode
[ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
(W) (setup)(C1) Creating TFT Screen
(W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
(I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
(I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
FastLED.
(W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
35040 bytes...
(W) (InitEffectsManager)(C1) InitEffectsManager...
(I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
(I) (InitEffectsManager)(C1) Creating EffectManager using default effects
Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
(W)
(W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
Launching Screen Thread. Mem: 142716, LargestBlk: 106484, PSRAM Free: 0/0,
>> Launching Audio Thread. Mem: 139572, LargestBlk: 102388, PSRAM Free:
0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
Launching Remote Thread. Mem: 135036, LargestBlk: 98292, PSRAM Free: 0/0,
(W) (begin)(C1) Remote Control Decoding Started
Launching Network Thread. Mem: 127856, LargestBlk: 90100, PSRAM Free: 0/0,
[ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
Error starting mDNS
Launching ColorData Thread. Mem: 119288, LargestBlk: 81908, PSRAM Free:
0/0, >> Launching Socket Thread. Mem: 116352, LargestBlk: 77812, PSRAM
Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
------------------------------
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
Exception -
(E) (TerminateHandler)(C0)
-------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C0) ------------------------------------------I)
(PrintOutputHeader)(C0)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 111880, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 <#1>
0x4009011d:0x3ffe6840 in esp_system_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 <#2>
0x40095799:0x3ffe6860 in abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 <#3>
0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
*)()) at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 <#4>
0x40191ace:0x3ffe6900 in std::terminate() at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 <#5>
0x40191a0f:0x3ffe6920 in __cxa_throw at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 <#6>
0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
(discriminator 4) #7
<#7>
0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2146) esp_core_dump_flash: Core dump flash config is corrupted!
CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
>> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
JSON, using defaults
(W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
(W) (setup)(C1) Starting ImprovSerial for ESP32
[ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
directory
(W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
"heidepiek", "********"
E (812) gpio: GPIO can only be used as input mode
[ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
E (823) gpio: GPIO can only be used as input mode
[ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
(W) (setup)(C1) Creating TFT Screen
(W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
(I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
(I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
FastLED.
(W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
35040 bytes...
(W) (InitEffectsManager)(C1) InitEffectsManager...
(I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
(I) (InitEffectsManager)(C1) Creating EffectManager using default effects
Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
(W)
(W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
Launching Screen Thread. Mem: 142704, LargestBlk: 106484, PSRAM Free: 0/0,
>> Launching Audio Thread. Mem: 139560, LargestBlk: 102388, PSRAM Free:
0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
Launching Remote Thread. Mem: 135024, LargestBlk: 98292, PSRAM Free: 0/0,
(W) (begin)(C1) Remote Control Decoding Started
Launching Network Thread. Mem: 127844, LargestBlk: 90100, PSRAM Free: 0/0,
[ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
Error starting mDNS
Launching ColorData Thread. Mem: 119276, LargestBlk: 81908, PSRAM Free:
0/0, >> Launching Socket Thread. Mem: 116340, LargestBlk: 77812, PSRAM
Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
------------------------------
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
Exception -
(E) (TerminateHandler)(C0)
-------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C0) ------------------------------------------I)
(PrintOutputHeader)(C0)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 111868, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 <#1>
0x4009011d:0x3ffe6840 in esp_system_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 <#2>
0x40095799:0x3ffe6860 in abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 <#3>
0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
*)()) at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 <#4>
0x40191ace:0x3ffe6900 in std::terminate() at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 <#5>
0x40191a0f:0x3ffe6920 in __cxa_throw at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 <#6>
0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
(discriminator 4) #7
<#7>
0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2145) esp_core_dump_flash: Core dump flash config is corrupted!
CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (647) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
>> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
JSON, using defaults
(W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
(W) (setup)(C1) Starting ImprovSerial for ESP32
[ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
directory
(W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
"heidepiek", "********"
E (812) gpio: GPIO can only be used as input mode
[ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
E (823) gpio: GPIO can only be used as input mode
[ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
(W) (setup)(C1) Creating TFT Screen
(W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
(I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
(I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
FastLED.
(W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
35040 bytes...
(W) (InitEffectsManager)(C1) InitEffectsManager...
(I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
(I) (InitEffectsManager)(C1) Creating EffectManager using default effects
Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
(W)
(W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
Launching Screen Thread. Mem: 142704, LargestBlk: 106484, PSRAM Free: 0/0,
>> Launching Audio Thread. Mem: 139560, LargestBlk: 102388, PSRAM Free:
0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
Launching Remote Thread. Mem: 135024, LargestBlk: 98292, PSRAM Free: 0/0,
(W) (begin)(C1) Remote Control Decoding Started
Launching Network Thread. Mem: 127844, LargestBlk: 90100, PSRAM Free: 0/0,
[ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
Error starting mDNS
Launching ColorData Thread. Mem: 119276, LargestBlk: 81908, PSRAM Free:
0/0, >> Launching Socket Thread. Mem: 116340, LargestBlk: 77812, PSRAM
Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
------------------------------
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
Exception -
(E) (TerminateHandler)(C0)
-------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C0) ------------------------------------------I)
(PrintOutputHeader)(C0)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 111868, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 <#1>
0x4009011d:0x3ffe6840 in esp_system_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 <#2>
0x40095799:0x3ffe6860 in abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 <#3>
0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
*)()) at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 <#4>
0x40191ace:0x3ffe6900 in std::terminate() at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 <#5>
0x40191a0f:0x3ffe6920 in __cxa_throw at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 <#6>
0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
(discriminator 4) #7
<#7>
0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2145) esp_core_dump_flash: Core dump flash config is corrupted!
CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
>> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
JSON, using defaults
(W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
(W) (setup)(C1) Starting ImprovSerial for ESP32
[ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
directory
(W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
"heidepiek", "
*" E (812) gpio: GPIO can only be used as input mode [
823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed E (817) gpio:
gpio_set_level(226): GPIO output gpio_num error E (823) gpio: GPIO can only
be used as input mode [ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO
config failed E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
(W) (setup)(C1) Creating TFT Screen (W) (InitializeHardware)(C1) Allocating
LEDStripGFX for channel 0 (I) (AddLEDsToFastLED)(C1) Adding LEDs to
FastLED... (I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from
channel 0 on FastLED. (W) (SetupBufferManagers)(C1) Reserving 15 LED
buffers for a total of 35040 bytes... (W) (InitEffectsManager)(C1)
InitEffectsManager... (I) (LoadJSONFile)(C1) Attempting to read JSON file
/effects.cfg (I) (InitEffectsManager)(C1) Creating EffectManager using
default effects Launching Drawing Thread. Mem: 149860, LargestBlk: 110580,
PSRAM Free: 0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry (W) (W)
(DrawLoopTaskEntry)(C1) Entering main draw loop! Launching Screen Thread.
Mem: 142704, LargestBlk: 106484, PSRAM Free: 0/0, >> Launching Audio
Thread. Mem: 139560, LargestBlk: 102388, PSRAM Free: 0/0, (I)
(AudioSamplerTaskEntry)(C0) >>> Sampler Task Started Launching Remote
Thread. Mem: 135024, LargestBlk: 98292, PSRAM Free: 0/0, (W) (begin)(C1)
Remote Control Decoding Started Launching Network Thread. Mem: 127844,
LargestBlk: 90100, PSRAM Free: 0/0, [ 1549][E][ESPmDNS.cpp:65] begin():
Failed starting MDNS Error starting mDNS Launching ColorDE (648)
esp_core_dump_flash: No core dum����ѥѥ���found! E (648)
esp_core_dump_flash: No core dump partition found! Replacing Idle Tasks
with TaskManager... (I) (PrintOutputHeader)(C1) NightDriverStrip (I) (I)
(PrintOutputHeader)(C1)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1 (I)
(PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32 Free
Memory: 206472, PSRAM:0, PSRAM Free: 0 (I) (PrintOutputHeader)(C1) ESP32
Clock Freq : 240 MHz (I) (setup)(C1) Startup! (I) (setup)(C1) Starting
DebugLoopTaskEntry Launching Debug Thread. Mem: 206472, LargestBlk: 110580,
PSRAM Free: 0/0, >> Launching JSON Writer Thread. Mem: 197868, LargestBlk:
110580, PSRAM Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be
loaded from JSON, using defaults (W) (NotifyJSONWriterThread)(C1) >>
Notifying JSON Writer Thread (W) (setup)(C1) Starting ImprovSerial for
ESP32 [ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or
is directory (W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
"heidepiek", "*"
E (812) gpio: GPIO can only be used as input mode
[ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
E (823) gpio: GPIO can only be used as input mode
[ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
(W) (setup)(C1) Creating TFT Screen
(W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
(I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
(I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
FastLED.
(W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
35040 bytes...
(W) (InitEffectsManager)(C1) InitEffectsManager...
(I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
(I) (InitEffectsManager)(C1) Creating EffectManager using default effects
Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
(W)
(W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
Launching Screen Thread. Mem: 142716, LargestBlk: 106484, PSRAM Free: 0/0,
>> Launching Audio Thread. Mem: 139572, LargestBlk: 102388, PSRAM Free:
0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
Launching Remote Thread. Mem: 135036, LargestBlk: 98292, PSRAM Free: 0/0,
(W) (begin)(C1) Remote Control Decoding Started
Launching Network Thread. Mem: 127856, LargestBlk: 90100, PSRAM Free: 0/0,
[ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
Error starting mDNS
Launching ColorData Thread. Mem: 119288, LargestBlk: 81908, PSRAM Free:
0/0, >> Launching Socket Thread. Mem: 116352, LargestBlk: 77812, PSRAM
Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
------------------------------
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
Exception -
(E) (TerminateHandler)(C0)
-------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
I) (PrintOutputHeader)(C0) NightDriverStrip
-------------------(I)
(I) (PrintOutputHeader)(C0)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 111880, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 <#1>
0x4009011d:0x3ffe6840 in esp_system_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 <#2>
0x40095799:0x3ffe6860 in abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 <#3>
0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
*)()) at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 <#4>
0x40191ace:0x3ffe6900 in std::terminate() at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 <#5>
0x40191a0f:0x3ffe6920 in __cxa_throw at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 <#6>
0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
(discriminator 4) #7
<#7>
0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2136) esp_core_dump_flash: Core dump flash config is corrupted!
CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
>> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
JSON, using defaults
(W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
(W) (setup)(C1) Starting ImprovSerial for ESP32
[ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
directory
(W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
"heidepiek", "********"
E (812) gpio: GPIO can only be used as input mode
[ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
E (823) gpio: GPIO can only be used as input mode
[ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
(W) (setup)(C1) Creating TFT Screen
(W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
(I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
(I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
FastLED.
(W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
35040 bytes...
(W) (InitEffectsManager)(C1) InitEffectsManager...
(I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
(I) (InitEffectsManager)(C1) Creating EffectManager using default effects
Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
(W)
(W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
Launching Screen Thread. Mem: 142704, LargestBlk: 106484, PSRAM Free: 0/0,
>> Launching Audio Thread. Mem: 139560, LargestBlk: 102388, PSRAM Free:
0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
Launching Remote Thread. Mem: 135024, LargestBlk: 98292, PSRAM Free: 0/0,
(W) (begin)(C1) Remote Control Decoding Started
Launching Network Thread. Mem: 127844, LargestBlk: 90100, PSRAM Free: 0/0,
[ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
Error starting mDNS
Launching ColorData Thread. Mem: 119276, LargestBlk: 81908, PSRAM Free:
0/0, >> Launching Socket Thread. Mem: 116340, LargestBlk: 77812, PSRAM
Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
------------------------------
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
Exception -
(E) (TerminateHandler)(C0)
-------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C0) ------------------------------------------I)
(PrintOutputHeader)(C0)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 111868, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 <#1>
0x4009011d:0x3ffe6840 in esp_system_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 <#2>
0x40095799:0x3ffe6860 in abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 <#3>
0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
*)()) at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 <#4>
0x40191ace:0x3ffe6900 in std::terminate() at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 <#5>
0x40191a0f:0x3ffe6920 in __cxa_throw at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 <#6>
0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
(discriminator 4) #7
<#7>
0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2145) esp_core_dump_flash: Core dump flash config is corrupted!
CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
>> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
JSON, using defaults
(W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
(W) (setup)(C1) Starting ImprovSerial for ESP32
[ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
directory
(W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
"heidepiek", "********"
E (812) gpio: GPIO can only be used as input mode
[ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
E (823) gpio: GPIO can only be used as input mode
[ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
(W) (setup)(C1) Creating TFT Screen
(W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
(I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
(I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
FastLED.
(W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
35040 bytes...
(W) (InitEffectsManager)(C1) InitEffectsManager...
(I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
(I) (InitEffectsManager)(C1) Creating EffectManager using default effects
Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
(W)
(W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
Launching Screen Thread. Mem: 142704, LargestBlk: 106484, PSRAM Free: 0/0,
>> Launching Audio Thread. Mem: 139560, LargestBlk: 102388, PSRAM Free:
0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
Launching Remote Thread. Mem: 135024, LargestBlk: 98292, PSRAM Free: 0/0,
(W) (begin)(C1) Remote Control Decoding Started
Launching Network Thread. Mem: 127844, LargestBlk: 90100, PSRAM Free: 0/0,
[ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
Error starting mDNS
Launching ColorData Thread. Mem: 119276, LargestBlk: 81908, PSRAM Free:
0/0, >> Launching Socket Thread. Mem: 116340, LargestBlk: 77812, PSRAM
Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
------------------------------
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
Exception -
(E) (TerminateHandler)(C0)
-------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C0) ------------------------------------------I)
(PrintOutputHeader)(C0)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 111868, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 <#1>
0x4009011d:0x3ffe6840 in esp_system_abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 <#2>
0x40095799:0x3ffe6860 in abort at
/Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 <#3>
0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
*)()) at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 <#4>
0x40191ace:0x3ffe6900 in std::terminate() at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 <#5>
0x40191a0f:0x3ffe6920 in __cxa_throw at
/builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 <#6>
0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
(discriminator 4) #7
<#7>
0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2145) esp_core_dump_flash: Core dump flash config is corrupted!
CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1)
------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
>> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
JSON, using defaults
(W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
(W) (setup)(C1) Starting ImprovSerial for ESP32
[ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
directory
(W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
"heidepiek", "********"
E (812) gpio: GPIO can only be used as input mode
[ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
E (823) gpio: GPIO can only be used as input mode
[ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
(W) (setup)(C1) Creating TFT Screen
Do i need to alter something in the global.h file?
#elif TTGO
// Variant of Spectrum set up for a TTGO using a MAX4466 microphone on pin27
// This project is set up as a 48x16 matrix of 16x16 WS2812B panels such as: https://amzn.to/3ABs5DK
// It displays a spectrum analyzer and music visualizer
#ifndef PROJECT_NAME
#define PROJECT_NAME "TTGO"
#endif
#define ENABLE_WIFI 1 // Connect to WiFi
#define INCOMING_WIFI_ENABLED 1 // Accepting incoming color data and commands
#define WAIT_FOR_WIFI 0 // Hold in setup until we have WiFi - for strips without effects
#define TIME_BEFORE_LOCAL 2 // How many seconds before the lamp times out and shows local content
#define ENABLE_WEBSERVER 1 // Turn on the internal webserver
#define ENABLE_NTP 0 // Set the clock from the web
#define ENABLE_OTA 0 // Accept over the air flash updates
#define ENABLE_REMOTE 1 // IR Remote Control
#define ENABLE_AUDIO 1 // Listen for audio from the microphone and process it
#define DEFAULT_EFFECT_INTERVAL (60*60*24)
#define MAX_BUFFERS 20
#define LED_PIN0 21 // Note that TFT board on TFTGO uses pins 19, 18, 5, 16, 23, and 4
#define NUM_CHANNELS 1
#define RING_SIZE_0 24
#define BONUS_PIXELS 0
#define MATRIX_WIDTH 48
#define MATRIX_HEIGHT 16
#define NUM_FANS MATRIX_WIDTH
#define FAN_SIZE MATRIX_HEIGHT
#define NUM_LEDS (MATRIX_WIDTH*MATRIX_HEIGHT)
#define IR_REMOTE_PIN 22
#define LED_FAN_OFFSET_BU 6
#define POWER_LIMIT_MW (1 * 5 * 1000) // Expects at least a 5V, 1A supply
#define TOGGLE_BUTTON_1 35
#define NUM_INFO_PAGES 4
#define ONSCREEN_SPECTRUM_PAGE 1 // Show a little spectrum analyzer on one of the info pages (slower)
#elif XMASTREES
// This project is set up as a 48x16 matrix of 16x16 WS2812B panels such as: https://amzn.to/3ABs5DK
// It uses an M5StickCPlus which has a microphone and LCD built in: https://amzn.to/3CrvCFh
// It displays a spectrum analyzer and music visualizer
#ifndef PROJECT_NAME
#define PROJECT_NAME "X-mas Trees"
#endif
#define ENABLE_WIFI 1 // Connect to WiFi
#define INCOMING_WIFI_ENABLED 1 // Accepting incoming color data and commands
#define WAIT_FOR_WIFI 0 // Hold in setup until we have WiFi - for strips without effects
#define TIME_BEFORE_LOCAL 2 // How many seconds before the lamp times out and shows local content
#define ENABLE_WEBSERVER 1 // Turn on the internal webserver
#define ENABLE_NTP 1 // Set the clock from the web
#define ENABLE_OTA 0 // Accept over the air flash updates
#define ENABLE_REMOTE 1 // IR Remote Control
#define ENABLE_AUDIO 1 // Listen for audio from the microphone and process it
#define DEFAULT_EFFECT_INTERVAL (60*60*24)
#define MAX_BUFFERS 20
#define LED_PIN0 26
#define NUM_CHANNELS 1
#define RING_SIZE_0 24
#define BONUS_PIXELS 0
#define MATRIX_WIDTH 24
#define MATRIX_HEIGHT 5
#define FAN_SIZE MATRIX_WIDTH
#define NUM_FANS MATRIX_HEIGHT
#define NUM_LEDS (MATRIX_WIDTH*MATRIX_HEIGHT)
#define IR_REMOTE_PIN 25
#define LED_FAN_OFFSET_BU 6
#define POWER_LIMIT_MW (5 * 5 * 1000) // Expects at least a 5V, 5A supply
#define TOGGLE_BUTTON_1 37
#define TOGGLE_BUTTON_2 39
#define NUM_INFO_PAGES 2
The board that i use works! The demo off the nightdriverstrip works! But
ttgo and spectrum i can`t get to work on this board.
specs of the board according to my suplier are:
Voedingsspanning: 3.3V DC of 5V DC
GPIO Spanning: 3.3V*
ESP32 chip (240Mhz dual core processor)
SRAM: 520KB
Flashgeheugen: 4MB
Ingebouwde Wi-Fi
Ingebouwde Bluetooth
Ingebouwd 1.14 inch (240x135) TFT (IPS) display (ST7789)
Ingebouwde drukknop
Ingebouwd Li-ion/Li-Po batterij oplaadcircuit: TP4054 chip kan tot 500mA laden
USB naar serieel converter: CP2104 of CH9102F ([drivers](https://www.tinytronics.nl/shop/index.php?route=information/information&information_id=30))
Batterij connector: 2p Molex Picoblade
Afmetingen PCB: 51.4 x 25.2mm
Inhoud verpakking:
1x TTGO T-Display V1.1 board
1x Batterij kabel: 2p Molex Picoblade
1x Male header set
Some advice please 😬
Greetzz harry
—
Reply to this email directly, view it on GitHub
<#462>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ACCSD37VDIUNI6PJPWTZ4VTX73K3XAVCNFSM6AAAAAA6EK7T3CVHI2DSMVQWIX3LMV43ERDJONRXK43TNFXW4OZVG42DOMBXHE>
.
You are receiving this because you are subscribed to this thread.Message
ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
1 reply
-
|
Thanks for the peptalk. I have the ttgo running the spectrum analyzer. greetz harry |
Beta Was this translation helpful? Give feedback.
Answer selected by
heidepiek
-
|
+1 on what @robertlipe said. Adding a little to that which I can because I'm not on a phone, the reboot that is triggered on screen.cpp line 403 occurs when Which takes us to line 519 of globals.h (part of the TTGO project block), which defines (On a sidenote, I found that |
Beta Was this translation helpful? Give feedback.
2 replies
-
|
Bedankt rutger voor de tip! Ik zag zonet dat in de repository nu van de nightdriverstrip de global.h header wat aangepast is bij de ttgo. Bij mijn global.h file stond bij ttgo : En heb hem nu aan de gang. For all the others who read this, sorry but in my own language i can express myself better. Greetzz harry |
Beta Was this translation helpful? Give feedback.
-
Ik heb PR #463 geopend precies om dit en een paar andere dingen te regelen. Als die PR gereviewed en gemerged is dan staat |
Beta Was this translation helpful? Give feedback.
-
|
I can confirm that I was able to get TTGO to work successfully by changing lines in globals to 👍 |
Beta Was this translation helpful? Give feedback.
0 replies
-
|
I have a vague memory of issues with a TTGO unit that had a VFD display and was based on the S3. As I recall, it was actually crashing due to memory pressure which causes the WiFi to blow up.
I’d try setting MAX_BUFFERS=10 and see if that helps, and if not, ENABLED_WIFI and WAIT_FOR_WIFI should be set to zero, see if that helps temporarily just for troubleshooting.
- Dave
… On Oct 17, 2023, at 12:39 PM, Robert Lipe ***@***.***> wrote:
I'm on a fone, but look at src/screen.cc:403 <http://screen.cc:403/>
You'll find a throw or dcheck or abort or dinner other kind of internal
consistency check that's falling.
Not to be jaded, but Do whatever it takes to make that not fail. 😉
If you don't have a. Screen, for example, turning off screen may be wise.
(Actually,. Even if you do,. It's not a bad troubleshooting step.)
On Tue, Oct 17, 2023, 2:19 PM heidepiek ***@***.***> wrote:
> Been tinkering with the nightdriverstrip software, and was testing out my
> ttgo board. I used line in platformio: [platformio]
> default_envs = ttgo
>
> I build it:
> build.odt
> <https://github.com/PlummersSoftwareLLC/NightDriverStrip/files/12938228/build.odt>
>
> And uploaded it:
> upload.odt
> <https://github.com/PlummersSoftwareLLC/NightDriverStrip/files/12938369/upload.odt>
>
> Then the ttgo keeps rebooting. Why does the board keeps rebooting? Does it
> have to do with the the 4mb flash?
> Thats the board im using. I know that there are 16mb flash boards. But i
> dont have that board. Dave has had the ttgo board running with the
> spectrum analyzer. I still havent managed to do that on the ttgo! I know
> dave recommends the dev_m5stick-c-plus, and that works like a charm. But it
> would be nice to have that also running on a ttgo. Maybe it`s because off
> the flash memory.
> I get this in the serial:
>
> Executing task: C:\Users\Eigenaar.platformio\penv\Scripts\platformio.exe
> device monitor --port COM6
>
> Please build project in debug configuration to get more details about an
> exception.
> See https://docs.platformio.org/page/projectconf/build_configurations.html
>
> --- Terminal on COM6 | 115200 8-N-1
> --- Available filters and text transformations: colorize, debug, default,
> direct, esp32_exception_decoder, hexlify, log2file, nocontrol, printable,
> send_on_enter, time
> --- More details at https://bit.ly/pio-monitor-filters
> --- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H
> ets Jul 29 2019 12:21:46
>
> rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
> configsip: 0, SPIWP:0xee
> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
> mode:DIO, clock div:2
> load:0x3fff0030,len:1184
> load:0x40078000,len:13232
> load:0x40080400,len:3028
> entry 0x400805e4
> E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
> E (648) esp_core_dump_flash: No core dump partition found!
> Replacing Idle Tasks with TaskManager...
> (I) (PrintOutputHeader)(C1) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C1)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 206472, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
> (I) (setup)(C1) Startup!
> (I) (setup)(C1) Starting DebugLoopTaskEntry
>
> Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
> >> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
> Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
> JSON, using defaults
> (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
> (W) (setup)(C1) Starting ImprovSerial for ESP32
> [ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
> directory
> (W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
> "heidepiek", "********"
> E (812) gpio: GPIO can only be used as input mode
> [ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
> E (823) gpio: GPIO can only be used as input mode
> [ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
> (W) (setup)(C1) Creating TFT Screen
> (W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
> (I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
> (I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
> FastLED.
> (W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
> 35040 bytes...
> (W) (InitEffectsManager)(C1) InitEffectsManager...
> (I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
> (I) (InitEffectsManager)(C1) Creating EffectManager using default effects
> Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
> 0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
> (W)
> (W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
> Launching Screen Thread. Mem: 142704, LargestBlk: 106484, PSRAM Free: 0/0,
> >> Launching Audio Thread. Mem: 139560, LargestBlk: 102388, PSRAM Free:
> 0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
> Launching Remote Thread. Mem: 135024, LargestBlk: 98292, PSRAM Free: 0/0,
> (W) (begin)(C1) Remote Control Decoding Started
> Launching Network Thread. Mem: 127844, LargestBlk: 90100, PSRAM Free: 0/0,
> [ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
> Error starting mDNS
> Launching ColorData Thread. Mem: 119276, LargestBlk: 81908, PSRAM Free:
> 0/0, >> Launching Socket Thread. Mem: 116340, LargestBlk: 77812, PSRAM
> Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
>
> ------------------------------
>
> (E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
> Exception -
> (E) (TerminateHandler)(C0)
> -------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C0) ------------------------------------------I)
> (PrintOutputHeader)(C0)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 111868, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
>
> abort() was called at PC 0x40191a7c on core 0
>
> Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
> 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
> 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
>
> #0 0x400850d5:0x3ffe6820 in panic_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
> #1 <#1>
> 0x4009011d:0x3ffe6840 in esp_system_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
> #2 <#2>
> 0x40095799:0x3ffe6860 in abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
> #3 <#3>
> 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
>
>
>
> *)()) at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51 <http://eh_terminate.cc:51/>
> #4 <#4>
> 0x40191ace:0x3ffe6900 in std::terminate() at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57 <http://eh_terminate.cc:57/>
> #5 <#5>
> 0x40191a0f:0x3ffe6920 in __cxa_throw at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95 <http://eh_throw.cc:95/>
> #6 <#6>
> 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
> (discriminator 4) #7
> <#7>
> 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
> src/screen.cpp:458
>
> ELF file SHA256: 6bf5667026ae3f4d
>
> E (2146) esp_core_dump_flash: Core dump flash config is corrupted!
> CRC=0x7bd5c66f instead of 0x0
> Rebooting...
> ets Jul 29 2019 12:21:46
>
> rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
> configsip: 0, SPIWP:0xee
> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
> mode:DIO, clock div:2
> load:0x3fff0030,len:1184
> load:0x40078000,len:13232
> load:0x40080400,len:3028
> entry 0x400805e4
> E (648) esp_core_dump_flash: No core dum���ѥѥ���found!
> E (648) esp_core_dump_flash: No core dump partition found!
> Replacing Idle Tasks with TaskManager...
> (I) (PrintOutputHeader)(C1) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C1)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 206472, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
> (I) (setup)(C1) Startup!
> (I) (setup)(C1) Starting DebugLoopTaskEntry
>
> Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
> >> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
> Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
> JSON, using defaults
> (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
> (W) (setup)(C1) Starting ImprovSerial for ESP32
> [ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
> directory
> (W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
> "heidepiek", "********"
> E (812) gpio: GPIO can only be used as input mode
> [ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
> E (823) gpio: GPIO can only be used as input mode
> [ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
> (W) (setup)(C1) Creating TFT Screen
> (W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
> (I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
> (I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
> FastLED.
> (W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
> 35040 bytes...
> (W) (InitEffectsManager)(C1) InitEffectsManager...
> (I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
> (I) (InitEffectsManager)(C1) Creating EffectManager using default effects
> Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
> 0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
> (W)
> (W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
> Launching Screen Thread. Mem: 142716, LargestBlk: 106484, PSRAM Free: 0/0,
> >> Launching Audio Thread. Mem: 139572, LargestBlk: 102388, PSRAM Free:
> 0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
> Launching Remote Thread. Mem: 135036, LargestBlk: 98292, PSRAM Free: 0/0,
> (W) (begin)(C1) Remote Control Decoding Started
> Launching Network Thread. Mem: 127856, LargestBlk: 90100, PSRAM Free: 0/0,
> [ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
> Error starting mDNS
> Launching ColorData Thread. Mem: 119288, LargestBlk: 81908, PSRAM Free:
> 0/0, >> Launching Socket Thread. Mem: 116352, LargestBlk: 77812, PSRAM
> Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
>
> ------------------------------
>
> (E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
> Exception -
> (E) (TerminateHandler)(C0)
> -------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) NightDriverStrip
> I) (PrintOutputHeader)(C0) NightDriverStrip
> -------------------(I)
> (I) (PrintOutputHeader)(C0)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 111880, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
>
> abort() was called at PC 0x40191a7c on core 0
>
> Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
> 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
> 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
>
> #0 0x400850d5:0x3ffe6820 in panic_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
> #1 <#1>
> 0x4009011d:0x3ffe6840 in esp_system_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
> #2 <#2>
> 0x40095799:0x3ffe6860 in abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
> #3 <#3>
> 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
>
>
>
> *)()) at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51 <http://eh_terminate.cc:51/>
> #4 <#4>
> 0x40191ace:0x3ffe6900 in std::terminate() at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57 <http://eh_terminate.cc:57/>
> #5 <#5>
> 0x40191a0f:0x3ffe6920 in __cxa_throw at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95 <http://eh_throw.cc:95/>
> #6 <#6>
> 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
> (discriminator 4) #7
> <#7>
> 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
> src/screen.cpp:458
>
> ELF file SHA256: 6bf5667026ae3f4d
>
> E (2136) esp_core_dump_flash: Core dump flash config is corrupted!
> CRC=0x7bd5c66f instead of 0x0
> Rebooting...
> ets Jul 29 2019 12:21:46
>
> rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
> configsip: 0, SPIWP:0xee
> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
> mode:DIO, clock div:2
> load:0x3fff0030,len:1184
> load:0x40078000,len:13232
> load:0x40080400,len:3028
> entry 0x400805e4
> ets Jul 29 2019 12:21:46
>
> rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
> configsip: 0, SPIWP:0xee
> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
> mode:DIO, clock div:2
> load:0x3fff0030,len:1184
> load:0x40078000,len:13232
> load:0x40080400,len:3028
> entry 0x400805e4
> E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
> E (648) esp_core_dump_flash: No core dump partition found!
> Replacing Idle Tasks with TaskManager...
> (I) (PrintOutputHeader)(C1) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C1)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 206472, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
> (I) (setup)(C1) Startup!
> (I) (setup)(C1) Starting DebugLoopTaskEntry
>
> Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
> >> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
> Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
> JSON, using defaults
> (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
> (W) (setup)(C1) Starting ImprovSerial for ESP32
> [ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
> directory
> (W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
> "heidepiek", "********"
> E (812) gpio: GPIO can only be used as input mode
> [ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
> E (823) gpio: GPIO can only be used as input mode
> [ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
> (W) (setup)(C1) Creating TFT Screen
> (W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
> (I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
> (I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
> FastLED.
> (W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
> 35040 bytes...
> (W) (InitEffectsManager)(C1) InitEffectsManager...
> (I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
> (I) (InitEffectsManager)(C1) Creating EffectManager using default effects
> Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
> 0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
> (W)
> (W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
> Launching Screen Thread. Mem: 142716, LargestBlk: 106484, PSRAM Free: 0/0,
> >> Launching Audio Thread. Mem: 139572, LargestBlk: 102388, PSRAM Free:
> 0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
> Launching Remote Thread. Mem: 135036, LargestBlk: 98292, PSRAM Free: 0/0,
> (W) (begin)(C1) Remote Control Decoding Started
> Launching Network Thread. Mem: 127856, LargestBlk: 90100, PSRAM Free: 0/0,
> [ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
> Error starting mDNS
> Launching ColorData Thread. Mem: 119288, LargestBlk: 81908, PSRAM Free:
> 0/0, >> Launching Socket Thread. Mem: 116352, LargestBlk: 77812, PSRAM
> Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
>
> ------------------------------
>
> (E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
> Exception -
> (E) (TerminateHandler)(C0)
> -------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C0) ------------------------------------------I)
> (PrintOutputHeader)(C0)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 111880, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
>
> abort() was called at PC 0x40191a7c on core 0
>
> Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
> 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
> 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
>
> #0 0x400850d5:0x3ffe6820 in panic_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
> #1 <#1>
> 0x4009011d:0x3ffe6840 in esp_system_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
> #2 <#2>
> 0x40095799:0x3ffe6860 in abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
> #3 <#3>
> 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
>
>
>
> *)()) at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51 <http://eh_terminate.cc:51/>
> #4 <#4>
> 0x40191ace:0x3ffe6900 in std::terminate() at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57 <http://eh_terminate.cc:57/>
> #5 <#5>
> 0x40191a0f:0x3ffe6920 in __cxa_throw at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95 <http://eh_throw.cc:95/>
> #6 <#6>
> 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
> (discriminator 4) #7
> <#7>
> 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
> src/screen.cpp:458
>
> ELF file SHA256: 6bf5667026ae3f4d
>
> E (2146) esp_core_dump_flash: Core dump flash config is corrupted!
> CRC=0x7bd5c66f instead of 0x0
> Rebooting...
> ets Jul 29 2019 12:21:46
>
> rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
> configsip: 0, SPIWP:0xee
> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
> mode:DIO, clock div:2
> load:0x3fff0030,len:1184
> load:0x40078000,len:13232
> load:0x40080400,len:3028
> entry 0x400805e4
> E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
> E (648) esp_core_dump_flash: No core dump partition found!
> Replacing Idle Tasks with TaskManager...
> (I) (PrintOutputHeader)(C1) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C1)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 206472, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
> (I) (setup)(C1) Startup!
> (I) (setup)(C1) Starting DebugLoopTaskEntry
>
> Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
> >> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
> Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
> JSON, using defaults
> (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
> (W) (setup)(C1) Starting ImprovSerial for ESP32
> [ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
> directory
> (W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
> "heidepiek", "********"
> E (812) gpio: GPIO can only be used as input mode
> [ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
> E (823) gpio: GPIO can only be used as input mode
> [ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
> (W) (setup)(C1) Creating TFT Screen
> (W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
> (I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
> (I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
> FastLED.
> (W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
> 35040 bytes...
> (W) (InitEffectsManager)(C1) InitEffectsManager...
> (I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
> (I) (InitEffectsManager)(C1) Creating EffectManager using default effects
> Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
> 0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
> (W)
> (W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
> Launching Screen Thread. Mem: 142704, LargestBlk: 106484, PSRAM Free: 0/0,
> >> Launching Audio Thread. Mem: 139560, LargestBlk: 102388, PSRAM Free:
> 0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
> Launching Remote Thread. Mem: 135024, LargestBlk: 98292, PSRAM Free: 0/0,
> (W) (begin)(C1) Remote Control Decoding Started
> Launching Network Thread. Mem: 127844, LargestBlk: 90100, PSRAM Free: 0/0,
> [ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
> Error starting mDNS
> Launching ColorData Thread. Mem: 119276, LargestBlk: 81908, PSRAM Free:
> 0/0, >> Launching Socket Thread. Mem: 116340, LargestBlk: 77812, PSRAM
> Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
>
> ------------------------------
>
> (E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
> Exception -
> (E) (TerminateHandler)(C0)
> -------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C0) ------------------------------------------I)
> (PrintOutputHeader)(C0)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 111868, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
>
> abort() was called at PC 0x40191a7c on core 0
>
> Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
> 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
> 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
>
> #0 0x400850d5:0x3ffe6820 in panic_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
> #1 <#1>
> 0x4009011d:0x3ffe6840 in esp_system_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
> #2 <#2>
> 0x40095799:0x3ffe6860 in abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
> #3 <#3>
> 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
>
>
>
> *)()) at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51 <http://eh_terminate.cc:51/>
> #4 <#4>
> 0x40191ace:0x3ffe6900 in std::terminate() at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57 <http://eh_terminate.cc:57/>
> #5 <#5>
> 0x40191a0f:0x3ffe6920 in __cxa_throw at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95 <http://eh_throw.cc:95/>
> #6 <#6>
> 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
> (discriminator 4) #7
> <#7>
> 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
> src/screen.cpp:458
>
> ELF file SHA256: 6bf5667026ae3f4d
>
> E (2145) esp_core_dump_flash: Core dump flash config is corrupted!
> CRC=0x7bd5c66f instead of 0x0
> Rebooting...
> ets Jul 29 2019 12:21:46
>
> rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
> configsip: 0, SPIWP:0xee
> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
> mode:DIO, clock div:2
> load:0x3fff0030,len:1184
> load:0x40078000,len:13232
> load:0x40080400,len:3028
> entry 0x400805e4
> E (647) esp_core_dump_flash: No core dum����ѥѥ���found!
> E (648) esp_core_dump_flash: No core dump partition found!
> Replacing Idle Tasks with TaskManager...
> (I) (PrintOutputHeader)(C1) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C1)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 206472, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
> (I) (setup)(C1) Startup!
> (I) (setup)(C1) Starting DebugLoopTaskEntry
>
> Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
> >> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
> Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
> JSON, using defaults
> (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
> (W) (setup)(C1) Starting ImprovSerial for ESP32
> [ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
> directory
> (W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
> "heidepiek", "********"
> E (812) gpio: GPIO can only be used as input mode
> [ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
> E (823) gpio: GPIO can only be used as input mode
> [ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
> (W) (setup)(C1) Creating TFT Screen
> (W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
> (I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
> (I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
> FastLED.
> (W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
> 35040 bytes...
> (W) (InitEffectsManager)(C1) InitEffectsManager...
> (I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
> (I) (InitEffectsManager)(C1) Creating EffectManager using default effects
> Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
> 0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
> (W)
> (W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
> Launching Screen Thread. Mem: 142704, LargestBlk: 106484, PSRAM Free: 0/0,
> >> Launching Audio Thread. Mem: 139560, LargestBlk: 102388, PSRAM Free:
> 0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
> Launching Remote Thread. Mem: 135024, LargestBlk: 98292, PSRAM Free: 0/0,
> (W) (begin)(C1) Remote Control Decoding Started
> Launching Network Thread. Mem: 127844, LargestBlk: 90100, PSRAM Free: 0/0,
> [ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
> Error starting mDNS
> Launching ColorData Thread. Mem: 119276, LargestBlk: 81908, PSRAM Free:
> 0/0, >> Launching Socket Thread. Mem: 116340, LargestBlk: 77812, PSRAM
> Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
>
> ------------------------------
>
> (E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
> Exception -
> (E) (TerminateHandler)(C0)
> -------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C0) ------------------------------------------I)
> (PrintOutputHeader)(C0)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 111868, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
>
> abort() was called at PC 0x40191a7c on core 0
>
> Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
> 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
> 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
>
> #0 0x400850d5:0x3ffe6820 in panic_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
> #1 <#1>
> 0x4009011d:0x3ffe6840 in esp_system_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
> #2 <#2>
> 0x40095799:0x3ffe6860 in abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
> #3 <#3>
> 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
>
>
>
> *)()) at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51 <http://eh_terminate.cc:51/>
> #4 <#4>
> 0x40191ace:0x3ffe6900 in std::terminate() at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57 <http://eh_terminate.cc:57/>
> #5 <#5>
> 0x40191a0f:0x3ffe6920 in __cxa_throw at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95 <http://eh_throw.cc:95/>
> #6 <#6>
> 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
> (discriminator 4) #7
> <#7>
> 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
> src/screen.cpp:458
>
> ELF file SHA256: 6bf5667026ae3f4d
>
> E (2145) esp_core_dump_flash: Core dump flash config is corrupted!
> CRC=0x7bd5c66f instead of 0x0
> Rebooting...
> ets Jul 29 2019 12:21:46
>
> rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
> configsip: 0, SPIWP:0xee
> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
> mode:DIO, clock div:2
> load:0x3fff0030,len:1184
> load:0x40078000,len:13232
> load:0x40080400,len:3028
> entry 0x400805e4
> E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
> E (648) esp_core_dump_flash: No core dump partition found!
> Replacing Idle Tasks with TaskManager...
> (I) (PrintOutputHeader)(C1) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C1)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 206472, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
> (I) (setup)(C1) Startup!
> (I) (setup)(C1) Starting DebugLoopTaskEntry
>
> Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
> >> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
> Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
> JSON, using defaults
> (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
> (W) (setup)(C1) Starting ImprovSerial for ESP32
> [ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
> directory
> (W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
> "heidepiek", "
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> *" E (812) gpio: GPIO can only be used as input mode [
> 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed E (817) gpio:
> gpio_set_level(226): GPIO output gpio_num error E (823) gpio: GPIO can only
> be used as input mode [ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO
> config failed E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
> (W) (setup)(C1) Creating TFT Screen (W) (InitializeHardware)(C1) Allocating
> LEDStripGFX for channel 0 (I) (AddLEDsToFastLED)(C1) Adding LEDs to
> FastLED... (I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from
> channel 0 on FastLED. (W) (SetupBufferManagers)(C1) Reserving 15 LED
> buffers for a total of 35040 bytes... (W) (InitEffectsManager)(C1)
> InitEffectsManager... (I) (LoadJSONFile)(C1) Attempting to read JSON file
> /effects.cfg (I) (InitEffectsManager)(C1) Creating EffectManager using
> default effects Launching Drawing Thread. Mem: 149860, LargestBlk: 110580,
> PSRAM Free: 0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry (W) (W)
> (DrawLoopTaskEntry)(C1) Entering main draw loop! Launching Screen Thread.
> Mem: 142704, LargestBlk: 106484, PSRAM Free: 0/0, >> Launching Audio
> Thread. Mem: 139560, LargestBlk: 102388, PSRAM Free: 0/0, (I)
> (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started Launching Remote
> Thread. Mem: 135024, LargestBlk: 98292, PSRAM Free: 0/0, (W) (begin)(C1)
> Remote Control Decoding Started Launching Network Thread. Mem: 127844,
> LargestBlk: 90100, PSRAM Free: 0/0, [ 1549][E][ESPmDNS.cpp:65] begin():
> Failed starting MDNS Error starting mDNS Launching ColorDE (648)
> esp_core_dump_flash: No core dum����ѥѥ���found! E (648)
> esp_core_dump_flash: No core dump partition found! Replacing Idle Tasks
> with TaskManager... (I) (PrintOutputHeader)(C1) NightDriverStrip (I) (I)
> (PrintOutputHeader)(C1)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1 (I)
> (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32 Free
> Memory: 206472, PSRAM:0, PSRAM Free: 0 (I) (PrintOutputHeader)(C1) ESP32
> Clock Freq : 240 MHz (I) (setup)(C1) Startup! (I) (setup)(C1) Starting
> DebugLoopTaskEntry Launching Debug Thread. Mem: 206472, LargestBlk: 110580,
> PSRAM Free: 0/0, >> Launching JSON Writer Thread. Mem: 197868, LargestBlk:
> 110580, PSRAM Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be
> loaded from JSON, using defaults (W) (NotifyJSONWriterThread)(C1) >>
> Notifying JSON Writer Thread (W) (setup)(C1) Starting ImprovSerial for
> ESP32 [ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or
> is directory (W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
> "heidepiek", "*"
> E (812) gpio: GPIO can only be used as input mode
> [ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
> E (823) gpio: GPIO can only be used as input mode
> [ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
> (W) (setup)(C1) Creating TFT Screen
> (W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
> (I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
> (I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
> FastLED.
> (W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
> 35040 bytes...
> (W) (InitEffectsManager)(C1) InitEffectsManager...
> (I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
> (I) (InitEffectsManager)(C1) Creating EffectManager using default effects
> Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
> 0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
> (W)
> (W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
> Launching Screen Thread. Mem: 142716, LargestBlk: 106484, PSRAM Free: 0/0,
> >> Launching Audio Thread. Mem: 139572, LargestBlk: 102388, PSRAM Free:
> 0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
> Launching Remote Thread. Mem: 135036, LargestBlk: 98292, PSRAM Free: 0/0,
> (W) (begin)(C1) Remote Control Decoding Started
> Launching Network Thread. Mem: 127856, LargestBlk: 90100, PSRAM Free: 0/0,
> [ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
> Error starting mDNS
> Launching ColorData Thread. Mem: 119288, LargestBlk: 81908, PSRAM Free:
> 0/0, >> Launching Socket Thread. Mem: 116352, LargestBlk: 77812, PSRAM
> Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
>
> ------------------------------
>
> (E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
> Exception -
> (E) (TerminateHandler)(C0)
> -------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) NightDriverStrip
> I) (PrintOutputHeader)(C0) NightDriverStrip
> -------------------(I)
> (I) (PrintOutputHeader)(C0)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 111880, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
>
> abort() was called at PC 0x40191a7c on core 0
>
> Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
> 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
> 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
>
> #0 0x400850d5:0x3ffe6820 in panic_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
> #1 <#1>
> 0x4009011d:0x3ffe6840 in esp_system_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
> #2 <#2>
> 0x40095799:0x3ffe6860 in abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
> #3 <#3>
> 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
>
>
>
> *)()) at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51 <http://eh_terminate.cc:51/>
> #4 <#4>
> 0x40191ace:0x3ffe6900 in std::terminate() at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57 <http://eh_terminate.cc:57/>
> #5 <#5>
> 0x40191a0f:0x3ffe6920 in __cxa_throw at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95 <http://eh_throw.cc:95/>
> #6 <#6>
> 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
> (discriminator 4) #7
> <#7>
> 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
> src/screen.cpp:458
>
> ELF file SHA256: 6bf5667026ae3f4d
>
> E (2136) esp_core_dump_flash: Core dump flash config is corrupted!
> CRC=0x7bd5c66f instead of 0x0
> Rebooting...
> ets Jul 29 2019 12:21:46
>
> rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
> configsip: 0, SPIWP:0xee
> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
> mode:DIO, clock div:2
> load:0x3fff0030,len:1184
> load:0x40078000,len:13232
> load:0x40080400,len:3028
> entry 0x400805e4
> E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
> E (648) esp_core_dump_flash: No core dump partition found!
> Replacing Idle Tasks with TaskManager...
> (I) (PrintOutputHeader)(C1) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C1)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 206472, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
> (I) (setup)(C1) Startup!
> (I) (setup)(C1) Starting DebugLoopTaskEntry
>
> Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
> >> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
> Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
> JSON, using defaults
> (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
> (W) (setup)(C1) Starting ImprovSerial for ESP32
> [ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
> directory
> (W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
> "heidepiek", "********"
> E (812) gpio: GPIO can only be used as input mode
> [ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
> E (823) gpio: GPIO can only be used as input mode
> [ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
> (W) (setup)(C1) Creating TFT Screen
> (W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
> (I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
> (I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
> FastLED.
> (W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
> 35040 bytes...
> (W) (InitEffectsManager)(C1) InitEffectsManager...
> (I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
> (I) (InitEffectsManager)(C1) Creating EffectManager using default effects
> Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
> 0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
> (W)
> (W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
> Launching Screen Thread. Mem: 142704, LargestBlk: 106484, PSRAM Free: 0/0,
> >> Launching Audio Thread. Mem: 139560, LargestBlk: 102388, PSRAM Free:
> 0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
> Launching Remote Thread. Mem: 135024, LargestBlk: 98292, PSRAM Free: 0/0,
> (W) (begin)(C1) Remote Control Decoding Started
> Launching Network Thread. Mem: 127844, LargestBlk: 90100, PSRAM Free: 0/0,
> [ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
> Error starting mDNS
> Launching ColorData Thread. Mem: 119276, LargestBlk: 81908, PSRAM Free:
> 0/0, >> Launching Socket Thread. Mem: 116340, LargestBlk: 77812, PSRAM
> Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
>
> ------------------------------
>
> (E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
> Exception -
> (E) (TerminateHandler)(C0)
> -------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C0) ------------------------------------------I)
> (PrintOutputHeader)(C0)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 111868, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
>
> abort() was called at PC 0x40191a7c on core 0
>
> Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
> 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
> 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
>
> #0 0x400850d5:0x3ffe6820 in panic_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
> #1 <#1>
> 0x4009011d:0x3ffe6840 in esp_system_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
> #2 <#2>
> 0x40095799:0x3ffe6860 in abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
> #3 <#3>
> 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
>
>
>
> *)()) at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51 <http://eh_terminate.cc:51/>
> #4 <#4>
> 0x40191ace:0x3ffe6900 in std::terminate() at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57 <http://eh_terminate.cc:57/>
> #5 <#5>
> 0x40191a0f:0x3ffe6920 in __cxa_throw at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95 <http://eh_throw.cc:95/>
> #6 <#6>
> 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
> (discriminator 4) #7
> <#7>
> 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
> src/screen.cpp:458
>
> ELF file SHA256: 6bf5667026ae3f4d
>
> E (2145) esp_core_dump_flash: Core dump flash config is corrupted!
> CRC=0x7bd5c66f instead of 0x0
> Rebooting...
> ets Jul 29 2019 12:21:46
>
> rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
> configsip: 0, SPIWP:0xee
> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
> mode:DIO, clock div:2
> load:0x3fff0030,len:1184
> load:0x40078000,len:13232
> load:0x40080400,len:3028
> entry 0x400805e4
> E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
> E (648) esp_core_dump_flash: No core dump partition found!
> Replacing Idle Tasks with TaskManager...
> (I) (PrintOutputHeader)(C1) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C1)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 206472, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
> (I) (setup)(C1) Startup!
> (I) (setup)(C1) Starting DebugLoopTaskEntry
>
> Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
> >> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
> Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
> JSON, using defaults
> (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
> (W) (setup)(C1) Starting ImprovSerial for ESP32
> [ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
> directory
> (W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
> "heidepiek", "********"
> E (812) gpio: GPIO can only be used as input mode
> [ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
> E (823) gpio: GPIO can only be used as input mode
> [ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
> (W) (setup)(C1) Creating TFT Screen
> (W) (InitializeHardware)(C1) Allocating LEDStripGFX for channel 0
> (I) (AddLEDsToFastLED)(C1) Adding LEDs to FastLED...
> (I) (AddLEDsToFastLED)(C1) Adding 768 LEDs to pin 21 from channel 0 on
> FastLED.
> (W) (SetupBufferManagers)(C1) Reserving 15 LED buffers for a total of
> 35040 bytes...
> (W) (InitEffectsManager)(C1) InitEffectsManager...
> (I) (LoadJSONFile)(C1) Attempting to read JSON file /effects.cfg
> (I) (InitEffectsManager)(C1) Creating EffectManager using default effects
> Launching Drawing Thread. Mem: 149860, LargestBlk: 110580, PSRAM Free:
> 0/0, (W) (DrawLoopTaskEntry)(C1) >> DrawLoopTaskEntry
> (W)
> (W) (DrawLoopTaskEntry)(C1) Entering main draw loop!
> Launching Screen Thread. Mem: 142704, LargestBlk: 106484, PSRAM Free: 0/0,
> >> Launching Audio Thread. Mem: 139560, LargestBlk: 102388, PSRAM Free:
> 0/0, (I) (AudioSamplerTaskEntry)(C0) >>> Sampler Task Started
> Launching Remote Thread. Mem: 135024, LargestBlk: 98292, PSRAM Free: 0/0,
> (W) (begin)(C1) Remote Control Decoding Started
> Launching Network Thread. Mem: 127844, LargestBlk: 90100, PSRAM Free: 0/0,
> [ 1549][E][ESPmDNS.cpp:65] begin(): Failed starting MDNS
> Error starting mDNS
> Launching ColorData Thread. Mem: 119276, LargestBlk: 81908, PSRAM Free:
> 0/0, >> Launching Socket Thread. Mem: 116340, LargestBlk: 77812, PSRAM
> Free: 0/0, (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
>
> ------------------------------
>
> (E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled
> Exception -
> (E) (TerminateHandler)(C0)
> -------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C0) ------------------------------------------I)
> (PrintOutputHeader)(C0)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 111868, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
>
> abort() was called at PC 0x40191a7c on core 0
>
> Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840
> 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900
> 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
>
> #0 0x400850d5:0x3ffe6820 in panic_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
> #1 <#1>
> 0x4009011d:0x3ffe6840 in esp_system_abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
> #2 <#2>
> 0x40095799:0x3ffe6860 in abort at
> /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
> #3 <#3>
> 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void (
>
>
>
> *)()) at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51 <http://eh_terminate.cc:51/>
> #4 <#4>
> 0x40191ace:0x3ffe6900 in std::terminate() at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57 <http://eh_terminate.cc:57/>
> #5 <#5>
> 0x40191a0f:0x3ffe6920 in __cxa_throw at
> /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95 <http://eh_throw.cc:95/>
> #6 <#6>
> 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403
> (discriminator 4) #7
> <#7>
> 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void*) at
> src/screen.cpp:458
>
> ELF file SHA256: 6bf5667026ae3f4d
>
> E (2145) esp_core_dump_flash: Core dump flash config is corrupted!
> CRC=0x7bd5c66f instead of 0x0
> Rebooting...
> ets Jul 29 2019 12:21:46
>
> rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
> configsip: 0, SPIWP:0xee
> clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
> mode:DIO, clock div:2
> load:0x3fff0030,len:1184
> load:0x40078000,len:13232
> load:0x40080400,len:3028
> entry 0x400805e4
> E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
> E (648) esp_core_dump_flash: No core dump partition found!
> Replacing Idle Tasks with TaskManager...
> (I) (PrintOutputHeader)(C1) NightDriverStrip
> (I)
> (I) (PrintOutputHeader)(C1)
> ------------------------------------------------------------------------------------------------------------
> (I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0,
> USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
> (I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32
> Free Memory: 206472, PSRAM:0, PSRAM Free: 0
> (I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
> (I) (setup)(C1) Startup!
> (I) (setup)(C1) Starting DebugLoopTaskEntry
>
> Launching Debug Thread. Mem: 206472, LargestBlk: 110580, PSRAM Free: 0/0,
> >> Launching JSON Writer Thread. Mem: 197868, LargestBlk: 110580, PSRAM
> Free: 0/0, (W) (DeviceConfig)(C1) DeviceConfig could not be loaded from
> JSON, using defaults
> (W) (NotifyJSONWriterThread)(C1) >> Notifying JSON Writer Thread
> (W) (setup)(C1) Starting ImprovSerial for ESP32
> [ 809][E][vfs_api.cpp:182] remove(): /improv.log does not exists or is
> directory
> (W) (ReadWiFiConfig)(C1) Retrieved SSID and Password from NVS:
> "heidepiek", "********"
> E (812) gpio: GPIO can only be used as input mode
> [ 823][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (817) gpio: gpio_set_level(226): GPIO output gpio_num error
> E (823) gpio: GPIO can only be used as input mode
> [ 837][E][esp32-hal-gpio.c:130] __pinMode(): GPIO config failed
> E (833) gpio: gpio_set_level(226): GPIO output gpio_num error
> (W) (setup)(C1) Creating TFT Screen
>
> Do i need to alter something in the global.h file?
>
> #elif TTGO
>
> // Variant of Spectrum set up for a TTGO using a MAX4466 microphone on pin27
>
> // This project is set up as a 48x16 matrix of 16x16 WS2812B panels such as: https://amzn.to/3ABs5DK
> // It displays a spectrum analyzer and music visualizer
>
> #ifndef PROJECT_NAME
> #define PROJECT_NAME "TTGO"
> #endif
>
> #define ENABLE_WIFI 1 // Connect to WiFi
> #define INCOMING_WIFI_ENABLED 1 // Accepting incoming color data and commands
> #define WAIT_FOR_WIFI 0 // Hold in setup until we have WiFi - for strips without effects
> #define TIME_BEFORE_LOCAL 2 // How many seconds before the lamp times out and shows local content
> #define ENABLE_WEBSERVER 1 // Turn on the internal webserver
> #define ENABLE_NTP 0 // Set the clock from the web
> #define ENABLE_OTA 0 // Accept over the air flash updates
> #define ENABLE_REMOTE 1 // IR Remote Control
> #define ENABLE_AUDIO 1 // Listen for audio from the microphone and process it
>
> #define DEFAULT_EFFECT_INTERVAL (60*60*24)
>
> #define MAX_BUFFERS 20
>
> #define LED_PIN0 21 // Note that TFT board on TFTGO uses pins 19, 18, 5, 16, 23, and 4
> #define NUM_CHANNELS 1
> #define RING_SIZE_0 24
> #define BONUS_PIXELS 0
> #define MATRIX_WIDTH 48
> #define MATRIX_HEIGHT 16
> #define NUM_FANS MATRIX_WIDTH
> #define FAN_SIZE MATRIX_HEIGHT
> #define NUM_LEDS (MATRIX_WIDTH*MATRIX_HEIGHT)
> #define IR_REMOTE_PIN 22
> #define LED_FAN_OFFSET_BU 6
> #define POWER_LIMIT_MW (1 * 5 * 1000) // Expects at least a 5V, 1A supply
>
> #define TOGGLE_BUTTON_1 35
> #define NUM_INFO_PAGES 4
> #define ONSCREEN_SPECTRUM_PAGE 1 // Show a little spectrum analyzer on one of the info pages (slower)
>
> #elif XMASTREES
>
> // This project is set up as a 48x16 matrix of 16x16 WS2812B panels such as: https://amzn.to/3ABs5DK
> // It uses an M5StickCPlus which has a microphone and LCD built in: https://amzn.to/3CrvCFh
> // It displays a spectrum analyzer and music visualizer
>
> #ifndef PROJECT_NAME
> #define PROJECT_NAME "X-mas Trees"
> #endif
>
> #define ENABLE_WIFI 1 // Connect to WiFi
> #define INCOMING_WIFI_ENABLED 1 // Accepting incoming color data and commands
> #define WAIT_FOR_WIFI 0 // Hold in setup until we have WiFi - for strips without effects
> #define TIME_BEFORE_LOCAL 2 // How many seconds before the lamp times out and shows local content
> #define ENABLE_WEBSERVER 1 // Turn on the internal webserver
> #define ENABLE_NTP 1 // Set the clock from the web
> #define ENABLE_OTA 0 // Accept over the air flash updates
> #define ENABLE_REMOTE 1 // IR Remote Control
> #define ENABLE_AUDIO 1 // Listen for audio from the microphone and process it
>
> #define DEFAULT_EFFECT_INTERVAL (60*60*24)
>
> #define MAX_BUFFERS 20
>
> #define LED_PIN0 26
> #define NUM_CHANNELS 1
> #define RING_SIZE_0 24
> #define BONUS_PIXELS 0
> #define MATRIX_WIDTH 24
> #define MATRIX_HEIGHT 5
> #define FAN_SIZE MATRIX_WIDTH
> #define NUM_FANS MATRIX_HEIGHT
> #define NUM_LEDS (MATRIX_WIDTH*MATRIX_HEIGHT)
> #define IR_REMOTE_PIN 25
> #define LED_FAN_OFFSET_BU 6
> #define POWER_LIMIT_MW (5 * 5 * 1000) // Expects at least a 5V, 5A supply
>
> #define TOGGLE_BUTTON_1 37
> #define TOGGLE_BUTTON_2 39
> #define NUM_INFO_PAGES 2
>
> The board that i use works! The demo off the nightdriverstrip works! But
> ttgo and spectrum i can`t get to work on this board.
> specs of the board according to my suplier are:
>
> Voedingsspanning: 3.3V DC of 5V DC
> GPIO Spanning: 3.3V*
> ESP32 chip (240Mhz dual core processor)
> SRAM: 520KB
> Flashgeheugen: 4MB
> Ingebouwde Wi-Fi
> Ingebouwde Bluetooth
> Ingebouwd 1.14 inch (240x135) TFT (IPS) display (ST7789)
> Ingebouwde drukknop
> Ingebouwd Li-ion/Li-Po batterij
|
Beta Was this translation helpful? Give feedback.
1 reply
-
ttgo.mp4Got it running, but in the global.h file this was higlighted (Variant of Spectrum set up for a TTGO using a MAX4466 microphone on pin27) Greetzz harry |
Beta Was this translation helpful? Give feedback.
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
-
Been tinkering with the nightdriverstrip software, and was testing out my ttgo board. I used line in platformio: [platformio]
default_envs = ttgo
I build it:
build.odt
And uploaded it:
upload.odt
Then the ttgo keeps rebooting. Why does the board keeps rebooting? Does it have to do with the the 4mb flash?
That
s the board im using. I know that there are 16mb flash boards. But i dont have that board. Dave has had the ttgo board running with the spectrum analyzer. I still havent managed to do that on the ttgo! I know dave recommends the dev_m5stick-c-plus, and that works like a charm. But it would be nice to have that also running on a ttgo. Maybe it`s because off the flash memory.I get this in the serial:
Executing task: C:\Users\Eigenaar.platformio\penv\Scripts\platformio.exe device monitor --port COM6
Please build project in debug configuration to get more details about an exception.
See https://docs.platformio.org/page/projectconf/build_configurations.html
--- Terminal on COM6 | 115200 8-N-1
--- Available filters and text transformations: colorize, debug, default, direct, esp32_exception_decoder, hexlify, log2file, nocontrol, printable, send_on_enter, time
--- More details at https://bit.ly/pio-monitor-filters
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H
ets Jul 29 2019 12:21:46
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled Exception -
(E) (TerminateHandler)(C0) -------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C0) ------------------------------------------I) (PrintOutputHeader)(C0) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 111868, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 0x4009011d:0x3ffe6840 in esp_system_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 0x40095799:0x3ffe6860 in abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void ()()) at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 0x40191ace:0x3ffe6900 in std::terminate() at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 0x40191a0f:0x3ffe6920 in __cxa_throw at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403 (discriminator 4)
#7 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void) at src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2146) esp_core_dump_flash: Core dump flash config is corrupted! CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum���ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled Exception -
(E) (TerminateHandler)(C0) -------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
I) (PrintOutputHeader)(C0) NightDriverStrip
-------------------(I)
(I) (PrintOutputHeader)(C0) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 111880, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 0x4009011d:0x3ffe6840 in esp_system_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 0x40095799:0x3ffe6860 in abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void ()()) at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 0x40191ace:0x3ffe6900 in std::terminate() at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 0x40191a0f:0x3ffe6920 in __cxa_throw at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403 (discriminator 4)
#7 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void) at src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2136) esp_core_dump_flash: Core dump flash config is corrupted! CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
ets Jul 29 2019 12:21:46
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled Exception -
(E) (TerminateHandler)(C0) -------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C0) ------------------------------------------I) (PrintOutputHeader)(C0) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 111880, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 0x4009011d:0x3ffe6840 in esp_system_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 0x40095799:0x3ffe6860 in abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void ()()) at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 0x40191ace:0x3ffe6900 in std::terminate() at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 0x40191a0f:0x3ffe6920 in __cxa_throw at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403 (discriminator 4)
#7 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void) at src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2146) esp_core_dump_flash: Core dump flash config is corrupted! CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled Exception -
(E) (TerminateHandler)(C0) -------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C0) ------------------------------------------I) (PrintOutputHeader)(C0) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 111868, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 0x4009011d:0x3ffe6840 in esp_system_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 0x40095799:0x3ffe6860 in abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void ()()) at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 0x40191ace:0x3ffe6900 in std::terminate() at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 0x40191a0f:0x3ffe6920 in __cxa_throw at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403 (discriminator 4)
#7 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void) at src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2145) esp_core_dump_flash: Core dump flash config is corrupted! CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (647) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled Exception -
(E) (TerminateHandler)(C0) -------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C0) ------------------------------------------I) (PrintOutputHeader)(C0) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 111868, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 0x4009011d:0x3ffe6840 in esp_system_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 0x40095799:0x3ffe6860 in abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void ()()) at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 0x40191ace:0x3ffe6900 in std::terminate() at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 0x40191a0f:0x3ffe6920 in __cxa_throw at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403 (discriminator 4)
#7 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void) at src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2145) esp_core_dump_flash: Core dump flash config is corrupted! CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled Exception -
(E) (TerminateHandler)(C0) -------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
I) (PrintOutputHeader)(C0) NightDriverStrip
-------------------(I)
(I) (PrintOutputHeader)(C0) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 111880, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 0x4009011d:0x3ffe6840 in esp_system_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 0x40095799:0x3ffe6860 in abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void ()()) at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 0x40191ace:0x3ffe6900 in std::terminate() at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 0x40191a0f:0x3ffe6920 in __cxa_throw at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403 (discriminator 4)
#7 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void) at src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2136) esp_core_dump_flash: Core dump flash config is corrupted! CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled Exception -
(E) (TerminateHandler)(C0) -------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C0) ------------------------------------------I) (PrintOutputHeader)(C0) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 111868, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 0x4009011d:0x3ffe6840 in esp_system_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 0x40095799:0x3ffe6860 in abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void ()()) at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 0x40191ace:0x3ffe6900 in std::terminate() at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 0x40191a0f:0x3ffe6920 in __cxa_throw at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403 (discriminator 4)
#7 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void) at src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2145) esp_core_dump_flash: Core dump flash config is corrupted! CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
(E) (TerminateHandler)(C0) - NightDriverStrip Guru Meditation Unhandled Exception -
(E) (TerminateHandler)(C0) -------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C0) ------------------------------------------I) (PrintOutputHeader)(C0) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C0) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C0) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 111868, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C0) ESP32 Clock Freq : 240 MHz
abort() was called at PC 0x40191a7c on core 0
Backtrace: 0x400850d5:0x3ffe6820 0x4009011d:0x3ffe6840 0x40095799:0x3ffe6860 0x40191a7c:0x3ffe68e0 0x40191ace:0x3ffe6900 0x40191a0f:0x3ffe6920 0x400828cd:0x3ffe6940 0x40082965:0x3ffe6960
#0 0x400850d5:0x3ffe6820 in panic_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/panic.c:408
#1 0x4009011d:0x3ffe6840 in esp_system_abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/esp_system/esp_system.c:137
#2 0x40095799:0x3ffe6860 in abort at /Users/ficeto/Desktop/ESP32/ESP32S2/esp-idf-public/components/newlib/abort.c:46
#3 0x40191a7c:0x3ffe68e0 in __cxxabiv1::__terminate(void ()()) at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:51
#4 0x40191ace:0x3ffe6900 in std::terminate() at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_terminate.cc:57
#5 0x40191a0f:0x3ffe6920 in __cxa_throw at /builds/idf/crosstool-NG/.build/HOST-x86_64-w64-mingw32/xtensa-esp32-elf/src/gcc/libstdc++-v3/libsupc++/eh_throw.cc:95
#6 0x400828cd:0x3ffe6940 in UpdateScreen(bool) at src/screen.cpp:403 (discriminator 4)
#7 0x40082965:0x3ffe6960 in ScreenUpdateLoopEntry(void) at src/screen.cpp:458
ELF file SHA256: 6bf5667026ae3f4d
E (2145) esp_core_dump_flash: Core dump flash config is corrupted! CRC=0x7bd5c66f instead of 0x0
Rebooting...
ets Jul 29 2019 12:21:46
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:1184
load:0x40078000,len:13232
load:0x40080400,len:3028
entry 0x400805e4
E (648) esp_core_dump_flash: No core dum����ѥѥ���found!
E (648) esp_core_dump_flash: No core dump partition found!
Replacing Idle Tasks with TaskManager...
(I) (PrintOutputHeader)(C1) NightDriverStrip
(I)
(I) (PrintOutputHeader)(C1) ------------------------------------------------------------------------------------------------------------
(I) (PrintOutputHeader)(C1) M5STICKC: 0, USE_M5DISPLAY: 0, USE_OLED: 0, USE_TFTSPI: 1, USE_LCD: 0, USE_AUDIO: 1, ENABLE_REMOTE: 1
(I) (PrintOutputHeader)(C1) Version 40: Wifi SSID: "heidepiek" - ESP32 Free Memory: 206472, PSRAM:0, PSRAM Free: 0
(I) (PrintOutputHeader)(C1) ESP32 Clock Freq : 240 MHz
(I) (setup)(C1) Startup!
(I) (setup)(C1) Starting DebugLoopTaskEntry
Do i need to alter something in the global.h file?
#elif TTGO
#elif XMASTREES
The board that i use works! The demo off the nightdriverstrip works! But ttgo and spectrum i can`t get to work on this board.
specs of the board according to my suplier are:
Inhoud verpakking:
Some advice please 😬
Greetzz harry
Beta Was this translation helpful? Give feedback.
All reactions