Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Pull networking fixes from David Miller:

 1) Use after free and new device IDs in bluetooth from Andre Guedes,
    Yevgeniy Melnichuk, Gustavo Padovan, and Henrik Rydberg.

 2) Fix crashes with short packet lengths and VLAN in pktgen, from
    Nishank Trivedi.

 3) mISDN calls flush_work_sync() with locks held, fix from Karsten
    Keil.

 4) Packet scheduler gred parameters are reported to userspace
    improperly scaled, and WRED idling is not performed correctly.  All
    from David Ward.

 5) Fix TCP socket refcount problem in ipv6, from Julian Anastasov.

 6) ibmveth device has RX queue alignment requirements which are not
    being explicitly met resulting in sporadic failures, fix from
    Santiago Leon.

 7) Netfilter needs to take care when interpreting sockets attached to
    socket buffers, they could be time-wait minisockets.  Fix from Eric
    Dumazet.

 8) sock_edemux() has the same issue as netfilter did in #7 above, fix
    from Eric Dumazet.

 9) Avoid infinite loops in CBQ scheduler with some configurations, from
    Eric Dumazet.

10) Deal with "Reflection scan: an Off-Path Attack on TCP", from Jozsef
    Kadlecsik.

11) SCTP overcharges socket for TX packets, fix from Thomas Graf.

12) CODEL packet scheduler should not reset it's state every time it
    builds a new flow, fix from Eric Dumazet.

13) Fix memory leak in nl80211, from Wei Yongjun.

14) NETROM doesn't check skb_copy_datagram_iovec() return values, from
    Alan Cox.

15) l2tp ethernet was using sizeof(ETH_HLEN) instead of plain ETH_HLEN,
    oops.  From Eric Dumazet.

16) Fix selection of ath9k chips on which PA linearization and AM2PM
    predistoration are used, from Felix Fietkau.

17) Flow steering settings in mlx4 driver need to be validated properly,
    from Hadar Hen Zion.

18) bnx2x doesn't show the correct link duplex setting, from Yaniv
    Rosner.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
  pktgen: fix crash with vlan and packet size less than 46
  bnx2x: Add missing afex code
  bnx2x: fix registers dumped
  bnx2x: correct advertisement of pause capabilities
  bnx2x: display the correct duplex value
  bnx2x: prevent timeouts when using PFC
  bnx2x: fix stats copying logic
  bnx2x: Avoid sending multiple statistics queries
  net: qmi_wwan: call subdriver with control intf only
  net_sched: gred: actually perform idling in WRED mode
  net_sched: gred: fix qave reporting via netlink
  net_sched: gred: eliminate redundant DP prio comparisons
  net_sched: gred: correct comment about qavg calculation in RIO mode
  mISDN: Fix wrong usage of flush_work_sync while holding locks
  netfilter: log: Fix log-level processing
  net-sched: sch_cbq: avoid infinite loop
  net: qmi_wwan: fix Gobi device probing for un2430
  net: fix net/core/sock.c build error
  ixp4xx_hss: fix build failure due to missing linux/module.h inclusion
  caif: move the dereference below the NULL test
  ...

drivers/bluetooth/ath3k.c

@@ -86,6 +86,7 @@ static struct usb_device_id ath3k_table[] = {
 
 	/* Atheros AR5BBU22 with sflash firmware */
 	{ USB_DEVICE(0x0489, 0xE03C) },
+	{ USB_DEVICE(0x0489, 0xE036) },
 
 	{ }	/* Terminating entry */
 };
@@ -109,6 +110,7 @@ static struct usb_device_id ath3k_blist_tbl[] = {
 
 	/* Atheros AR5BBU22 with sflash firmware */
 	{ USB_DEVICE(0x0489, 0xE03C), .driver_info = BTUSB_ATH3012 },
+	{ USB_DEVICE(0x0489, 0xE036), .driver_info = BTUSB_ATH3012 },
 
 	{ }	/* Terminating entry */
 };

drivers/bluetooth/btusb.c

@@ -52,6 +52,9 @@ static struct usb_device_id btusb_table[] = {
 	/* Generic Bluetooth USB device */
 	{ USB_DEVICE_INFO(0xe0, 0x01, 0x01) },
 
+	/* Apple-specific (Broadcom) devices */
+	{ USB_VENDOR_AND_INTERFACE_INFO(0x05ac, 0xff, 0x01, 0x01) },
+
 	/* Broadcom SoftSailing reporting vendor specific */
 	{ USB_DEVICE(0x0a5c, 0x21e1) },
 
@@ -94,16 +97,14 @@ static struct usb_device_id btusb_table[] = {
 
 	/* Broadcom BCM20702A0 */
 	{ USB_DEVICE(0x0489, 0xe042) },
-	{ USB_DEVICE(0x0a5c, 0x21e3) },
-	{ USB_DEVICE(0x0a5c, 0x21e6) },
-	{ USB_DEVICE(0x0a5c, 0x21e8) },
-	{ USB_DEVICE(0x0a5c, 0x21f3) },
-	{ USB_DEVICE(0x0a5c, 0x21f4) },
 	{ USB_DEVICE(0x413c, 0x8197) },
 
 	/* Foxconn - Hon Hai */
 	{ USB_DEVICE(0x0489, 0xe033) },
 
+	/*Broadcom devices with vendor specific id */
+	{ USB_VENDOR_AND_INTERFACE_INFO(0x0a5c, 0xff, 0x01, 0x01) },
+
 	{ }	/* Terminating entry */
 };
 
@@ -141,6 +142,7 @@ static struct usb_device_id blacklist_table[] = {
 
 	/* Atheros AR5BBU12 with sflash firmware */
 	{ USB_DEVICE(0x0489, 0xe03c), .driver_info = BTUSB_ATH3012 },
+	{ USB_DEVICE(0x0489, 0xe036), .driver_info = BTUSB_ATH3012 },
 
 	/* Broadcom BCM2035 */
 	{ USB_DEVICE(0x0a5c, 0x2035), .driver_info = BTUSB_WRONG_SCO_MTU },

drivers/isdn/hardware/mISDN/avmfritz.c

@@ -857,8 +857,9 @@ avm_bctrl(struct mISDNchannel *ch, u32 cmd, void *arg)
 	switch (cmd) {
 	case CLOSE_CHANNEL:
 		test_and_clear_bit(FLG_OPEN, &bch->Flags);
+		cancel_work_sync(&bch->workq);
 		spin_lock_irqsave(&fc->lock, flags);
-		mISDN_freebchannel(bch);
+		mISDN_clear_bchannel(bch);
 		modehdlc(bch, ISDN_P_NONE);
 		spin_unlock_irqrestore(&fc->lock, flags);
 		ch->protocol = ISDN_P_NONE;

drivers/isdn/hardware/mISDN/hfcmulti.c

@@ -5059,6 +5059,7 @@ hfcmulti_init(struct hm_map *m, struct pci_dev *pdev,
 				printk(KERN_INFO
 				       "HFC-E1 #%d has overlapping B-channels on fragment #%d\n",
 				       E1_cnt + 1, pt);
+				kfree(hc);
 				return -EINVAL;
 			}
 			maskcheck |= hc->bmask[pt];
@@ -5086,6 +5087,7 @@ hfcmulti_init(struct hm_map *m, struct pci_dev *pdev,
 	if ((poll >> 1) > sizeof(hc->silence_data)) {
 		printk(KERN_ERR "HFCMULTI error: silence_data too small, "
 		       "please fix\n");
+		kfree(hc);
 		return -EINVAL;
 	}
 	for (i = 0; i < (poll >> 1); i++)

drivers/isdn/hardware/mISDN/mISDNipac.c

@@ -1406,8 +1406,9 @@ hscx_bctrl(struct mISDNchannel *ch, u32 cmd, void *arg)
 	switch (cmd) {
 	case CLOSE_CHANNEL:
 		test_and_clear_bit(FLG_OPEN, &bch->Flags);
+		cancel_work_sync(&bch->workq);
 		spin_lock_irqsave(hx->ip->hwlock, flags);
-		mISDN_freebchannel(bch);
+		mISDN_clear_bchannel(bch);
 		hscx_mode(hx, ISDN_P_NONE);
 		spin_unlock_irqrestore(hx->ip->hwlock, flags);
 		ch->protocol = ISDN_P_NONE;

drivers/isdn/hardware/mISDN/mISDNisar.c

@@ -1588,8 +1588,9 @@ isar_bctrl(struct mISDNchannel *ch, u32 cmd, void *arg)
 	switch (cmd) {
 	case CLOSE_CHANNEL:
 		test_and_clear_bit(FLG_OPEN, &bch->Flags);
+		cancel_work_sync(&bch->workq);
 		spin_lock_irqsave(ich->is->hwlock, flags);
-		mISDN_freebchannel(bch);
+		mISDN_clear_bchannel(bch);
 		modeisar(ich, ISDN_P_NONE);
 		spin_unlock_irqrestore(ich->is->hwlock, flags);
 		ch->protocol = ISDN_P_NONE;

drivers/isdn/hardware/mISDN/netjet.c

@@ -812,8 +812,9 @@ nj_bctrl(struct mISDNchannel *ch, u32 cmd, void *arg)
 	switch (cmd) {
 	case CLOSE_CHANNEL:
 		test_and_clear_bit(FLG_OPEN, &bch->Flags);
+		cancel_work_sync(&bch->workq);
 		spin_lock_irqsave(&card->lock, flags);
-		mISDN_freebchannel(bch);
+		mISDN_clear_bchannel(bch);
 		mode_tiger(bc, ISDN_P_NONE);
 		spin_unlock_irqrestore(&card->lock, flags);
 		ch->protocol = ISDN_P_NONE;

drivers/isdn/hardware/mISDN/w6692.c

@@ -1054,8 +1054,9 @@ w6692_bctrl(struct mISDNchannel *ch, u32 cmd, void *arg)
 	switch (cmd) {
 	case CLOSE_CHANNEL:
 		test_and_clear_bit(FLG_OPEN, &bch->Flags);
+		cancel_work_sync(&bch->workq);
 		spin_lock_irqsave(&card->lock, flags);
-		mISDN_freebchannel(bch);
+		mISDN_clear_bchannel(bch);
 		w6692_mode(bc, ISDN_P_NONE);
 		spin_unlock_irqrestore(&card->lock, flags);
 		ch->protocol = ISDN_P_NONE;

drivers/isdn/mISDN/hwchannel.c

@@ -148,17 +148,16 @@ mISDN_clear_bchannel(struct bchannel *ch)
 	ch->next_minlen = ch->init_minlen;
 	ch->maxlen = ch->init_maxlen;
 	ch->next_maxlen = ch->init_maxlen;
+	skb_queue_purge(&ch->rqueue);
+	ch->rcount = 0;
 }
 EXPORT_SYMBOL(mISDN_clear_bchannel);
 
-int
+void
 mISDN_freebchannel(struct bchannel *ch)
 {
+	cancel_work_sync(&ch->workq);
 	mISDN_clear_bchannel(ch);
-	skb_queue_purge(&ch->rqueue);
-	ch->rcount = 0;
-	flush_work_sync(&ch->workq);
-	return 0;
 }
 EXPORT_SYMBOL(mISDN_freebchannel);
 

drivers/net/can/mcp251x.c

@@ -83,6 +83,11 @@
 #define INSTRUCTION_LOAD_TXB(n)	(0x40 + 2 * (n))
 #define INSTRUCTION_READ_RXB(n)	(((n) == 0) ? 0x90 : 0x94)
 #define INSTRUCTION_RESET	0xC0
+#define RTS_TXB0		0x01
+#define RTS_TXB1		0x02
+#define RTS_TXB2		0x04
+#define INSTRUCTION_RTS(n)	(0x80 | ((n) & 0x07))
+
 
 /* MPC251x registers */
 #define CANSTAT	      0x0e
@@ -397,6 +402,7 @@ static void mcp251x_hw_tx_frame(struct spi_device *spi, u8 *buf,
 static void mcp251x_hw_tx(struct spi_device *spi, struct can_frame *frame,
 			  int tx_buf_idx)
 {
+	struct mcp251x_priv *priv = dev_get_drvdata(&spi->dev);
 	u32 sid, eid, exide, rtr;
 	u8 buf[SPI_TRANSFER_BUF_LEN];
 
@@ -418,7 +424,10 @@ static void mcp251x_hw_tx(struct spi_device *spi, struct can_frame *frame,
 	buf[TXBDLC_OFF] = (rtr << DLC_RTR_SHIFT) | frame->can_dlc;
 	memcpy(buf + TXBDAT_OFF, frame->data, frame->can_dlc);
 	mcp251x_hw_tx_frame(spi, buf, frame->can_dlc, tx_buf_idx);
-	mcp251x_write_reg(spi, TXBCTRL(tx_buf_idx), TXBCTRL_TXREQ);
+
+	/* use INSTRUCTION_RTS, to avoid "repeated frame problem" */
+	priv->spi_tx_buf[0] = INSTRUCTION_RTS(1 << tx_buf_idx);
+	mcp251x_spi_trans(priv->spi, 1);
 }
 
 static void mcp251x_hw_rx_frame(struct spi_device *spi, u8 *buf,

drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h

@@ -710,17 +710,15 @@ static inline u16 bnx2x_tx_avail(struct bnx2x *bp,
 	prod = txdata->tx_bd_prod;
 	cons = txdata->tx_bd_cons;
 
-	/* NUM_TX_RINGS = number of "next-page" entries
-	   It will be used as a threshold */
-	used = SUB_S16(prod, cons) + (s16)NUM_TX_RINGS;
+	used = SUB_S16(prod, cons);
 
 #ifdef BNX2X_STOP_ON_ERROR
 	WARN_ON(used < 0);
-	WARN_ON(used > bp->tx_ring_size);
-	WARN_ON((bp->tx_ring_size - used) > MAX_TX_AVAIL);
+	WARN_ON(used > txdata->tx_ring_size);
+	WARN_ON((txdata->tx_ring_size - used) > MAX_TX_AVAIL);
 #endif
 
-	return (s16)(bp->tx_ring_size) - used;
+	return (s16)(txdata->tx_ring_size) - used;
 }
 
 static inline int bnx2x_tx_queue_has_work(struct bnx2x_fp_txdata *txdata)
@@ -1088,6 +1086,7 @@ static inline void bnx2x_init_txdata(struct bnx2x *bp,
 	txdata->txq_index = txq_index;
 	txdata->tx_cons_sb = tx_cons_sb;
 	txdata->parent_fp = fp;
+	txdata->tx_ring_size = IS_FCOE_FP(fp) ? MAX_TX_AVAIL : bp->tx_ring_size;
 
 	DP(NETIF_MSG_IFUP, "created tx data cid %d, txq %d\n",
 	   txdata->cid, txdata->txq_index);

drivers/net/ethernet/broadcom/bnx2x/bnx2x_dump.h

@@ -401,11 +401,11 @@ static const struct reg_addr reg_addrs[] = {
 	{ 0x70000, 8, RI_ALL_ONLINE },
 	{ 0x70020, 8184, RI_ALL_OFFLINE },
 	{ 0x78000, 8192, RI_E3E3B0_OFFLINE },
-	{ 0x85000, 3, RI_ALL_ONLINE },
-	{ 0x8501c, 7, RI_ALL_ONLINE },
-	{ 0x85048, 1, RI_ALL_ONLINE },
-	{ 0x85200, 32, RI_ALL_ONLINE },
-	{ 0xb0000, 16384, RI_E1H_ONLINE },
+	{ 0x85000, 3, RI_ALL_OFFLINE },
+	{ 0x8501c, 7, RI_ALL_OFFLINE },
+	{ 0x85048, 1, RI_ALL_OFFLINE },
+	{ 0x85200, 32, RI_ALL_OFFLINE },
+	{ 0xb0000, 16384, RI_E1H_OFFLINE },
 	{ 0xc1000, 7, RI_ALL_ONLINE },
 	{ 0xc103c, 2, RI_E2E3E3B0_ONLINE },
 	{ 0xc1800, 2, RI_ALL_ONLINE },
@@ -581,17 +581,12 @@ static const struct reg_addr reg_addrs[] = {
 	{ 0x140188, 3, RI_E1E1HE2E3_ONLINE },
 	{ 0x140194, 13, RI_ALL_ONLINE },
 	{ 0x140200, 6, RI_E1E1HE2E3_ONLINE },
-	{ 0x140220, 4, RI_E2E3_ONLINE },
-	{ 0x140240, 4, RI_E2E3_ONLINE },
 	{ 0x140260, 4, RI_E2E3_ONLINE },
 	{ 0x140280, 4, RI_E2E3_ONLINE },
-	{ 0x1402a0, 4, RI_E2E3_ONLINE },
-	{ 0x1402c0, 4, RI_E2E3_ONLINE },
 	{ 0x1402e0, 2, RI_E2E3_ONLINE },
 	{ 0x1402e8, 2, RI_E2E3E3B0_ONLINE },
 	{ 0x1402f0, 9, RI_E2E3_ONLINE },
 	{ 0x140314, 44, RI_E3B0_ONLINE },
-	{ 0x1403d0, 70, RI_E3B0_ONLINE },
 	{ 0x144000, 4, RI_E1E1H_ONLINE },
 	{ 0x148000, 4, RI_E1E1H_ONLINE },
 	{ 0x14c000, 4, RI_E1E1H_ONLINE },
@@ -704,7 +699,6 @@ static const struct reg_addr reg_addrs[] = {
 	{ 0x180398, 1, RI_E2E3E3B0_ONLINE },
 	{ 0x1803a0, 5, RI_E2E3E3B0_ONLINE },
 	{ 0x1803b4, 2, RI_E3E3B0_ONLINE },
-	{ 0x180400, 1, RI_ALL_ONLINE },
 	{ 0x180404, 255, RI_E1E1H_OFFLINE },
 	{ 0x181000, 4, RI_ALL_ONLINE },
 	{ 0x181010, 1020, RI_ALL_OFFLINE },
@@ -800,9 +794,9 @@ static const struct reg_addr reg_addrs[] = {
 	{ 0x1b905c, 1, RI_E3E3B0_ONLINE },
 	{ 0x1b9064, 1, RI_E3B0_ONLINE },
 	{ 0x1b9080, 10, RI_E3B0_ONLINE },
-	{ 0x1b9400, 14, RI_E2E3E3B0_ONLINE },
-	{ 0x1b943c, 19, RI_E2E3E3B0_ONLINE },
-	{ 0x1b9490, 10, RI_E2E3E3B0_ONLINE },
+	{ 0x1b9400, 14, RI_E2E3E3B0_OFFLINE },
+	{ 0x1b943c, 19, RI_E2E3E3B0_OFFLINE },
+	{ 0x1b9490, 10, RI_E2E3E3B0_OFFLINE },
 	{ 0x1c0000, 2, RI_ALL_ONLINE },
 	{ 0x200000, 65, RI_ALL_ONLINE },
 	{ 0x20014c, 2, RI_E1HE2E3E3B0_ONLINE },
@@ -814,7 +808,6 @@ static const struct reg_addr reg_addrs[] = {
 	{ 0x200398, 1, RI_E2E3E3B0_ONLINE },
 	{ 0x2003a0, 1, RI_E2E3E3B0_ONLINE },
 	{ 0x2003a8, 2, RI_E2E3E3B0_ONLINE },
-	{ 0x200400, 1, RI_ALL_ONLINE },
 	{ 0x200404, 255, RI_E1E1H_OFFLINE },
 	{ 0x202000, 4, RI_ALL_ONLINE },
 	{ 0x202010, 2044, RI_ALL_OFFLINE },
@@ -921,7 +914,6 @@ static const struct reg_addr reg_addrs[] = {
 	{ 0x280398, 1, RI_E2E3E3B0_ONLINE },
 	{ 0x2803a0, 1, RI_E2E3E3B0_ONLINE },
 	{ 0x2803a8, 2, RI_E2E3E3B0_ONLINE },
-	{ 0x280400, 1, RI_ALL_ONLINE },
 	{ 0x280404, 255, RI_E1E1H_OFFLINE },
 	{ 0x282000, 4, RI_ALL_ONLINE },
 	{ 0x282010, 2044, RI_ALL_OFFLINE },
@@ -1031,7 +1023,6 @@ static const struct reg_addr reg_addrs[] = {
 	{ 0x300398, 1, RI_E2E3E3B0_ONLINE },
 	{ 0x3003a0, 1, RI_E2E3E3B0_ONLINE },
 	{ 0x3003a8, 2, RI_E2E3E3B0_ONLINE },
-	{ 0x300400, 1, RI_ALL_ONLINE },
 	{ 0x300404, 255, RI_E1E1H_OFFLINE },
 	{ 0x302000, 4, RI_ALL_ONLINE },
 	{ 0x302010, 2044, RI_ALL_OFFLINE },

drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c

@@ -775,7 +775,7 @@ static void bnx2x_get_regs(struct net_device *dev,
 	struct bnx2x *bp = netdev_priv(dev);
 	struct dump_hdr dump_hdr = {0};
 
-	regs->version = 0;
+	regs->version = 1;
 	memset(p, 0, regs->len);
 
 	if (!netif_running(bp->dev))
@@ -1587,6 +1587,12 @@ static int bnx2x_set_pauseparam(struct net_device *dev,
 			bp->link_params.req_flow_ctrl[cfg_idx] =
 				BNX2X_FLOW_CTRL_AUTO;
 		}
+		bp->link_params.req_fc_auto_adv = BNX2X_FLOW_CTRL_NONE;
+		if (epause->rx_pause)
+			bp->link_params.req_fc_auto_adv |= BNX2X_FLOW_CTRL_RX;
+
+		if (epause->tx_pause)
+			bp->link_params.req_fc_auto_adv |= BNX2X_FLOW_CTRL_TX;
 	}
 
 	DP(BNX2X_MSG_ETHTOOL,

drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c

@@ -2667,9 +2667,11 @@ int bnx2x_update_pfc(struct link_params *params,
 		return bnx2x_status;
 
 	DP(NETIF_MSG_LINK, "About to update PFC in BMAC\n");
-	if (CHIP_IS_E3(bp))
-		bnx2x_update_pfc_xmac(params, vars, 0);
-	else {
+
+	if (CHIP_IS_E3(bp)) {
+		if (vars->mac_type == MAC_TYPE_XMAC)
+			bnx2x_update_pfc_xmac(params, vars, 0);
+	} else {
 		val = REG_RD(bp, MISC_REG_RESET_REG_2);
 		if ((val &
 		     (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << params->port))
@@ -5432,15 +5434,15 @@ static int bnx2x_get_link_speed_duplex(struct bnx2x_phy *phy,
 		switch (speed_mask) {
 		case GP_STATUS_10M:
 			vars->line_speed = SPEED_10;
-			if (vars->duplex == DUPLEX_FULL)
+			if (is_duplex == DUPLEX_FULL)
 				vars->link_status |= LINK_10TFD;
 			else
 				vars->link_status |= LINK_10THD;
 			break;
 
 		case GP_STATUS_100M:
 			vars->line_speed = SPEED_100;
-			if (vars->duplex == DUPLEX_FULL)
+			if (is_duplex == DUPLEX_FULL)
 				vars->link_status |= LINK_100TXFD;
 			else
 				vars->link_status |= LINK_100TXHD;
@@ -5449,15 +5451,15 @@ static int bnx2x_get_link_speed_duplex(struct bnx2x_phy *phy,
 		case GP_STATUS_1G:
 		case GP_STATUS_1G_KX:
 			vars->line_speed = SPEED_1000;
-			if (vars->duplex == DUPLEX_FULL)
+			if (is_duplex == DUPLEX_FULL)
 				vars->link_status |= LINK_1000TFD;
 			else
 				vars->link_status |= LINK_1000THD;
 			break;
 
 		case GP_STATUS_2_5G:
 			vars->line_speed = SPEED_2500;
-			if (vars->duplex == DUPLEX_FULL)
+			if (is_duplex == DUPLEX_FULL)
 				vars->link_status |= LINK_2500TFD;
 			else
 				vars->link_status |= LINK_2500THD;
@@ -5531,6 +5533,7 @@ static int bnx2x_link_settings_status(struct bnx2x_phy *phy,
 
 	if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS) {
 		if (SINGLE_MEDIA_DIRECT(params)) {
+			vars->duplex = duplex;
 			bnx2x_flow_ctrl_resolve(phy, params, vars, gp_status);
 			if (phy->req_line_speed == SPEED_AUTO_NEG)
 				bnx2x_xgxs_an_resolve(phy, params, vars,
@@ -5625,6 +5628,7 @@ static int bnx2x_warpcore_read_status(struct bnx2x_phy *phy,
 					LINK_STATUS_PARALLEL_DETECTION_USED;
 			}
 			bnx2x_ext_phy_resolve_fc(phy, params, vars);
+			vars->duplex = duplex;
 		}
 	}