Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
The Kicker is Spring Power, Revolver style Blaster. It uses Half length darts
For Question about Puchasing Kits of Complete builds Contact me on reddit u/Free-Committee-1202 or by Email Slowworksm@gmail.com
Notice-The Kicker is not a toy and intended for Adults and Hobbists, I am not resposibile for injury due to use of the design. Proper eye protection and a orange front/tip should be used at all times.
Build videos found at https://www.youtube.com/channel/UC06lH3h-eoEIFO0K_K5rYGg
WATCH OUT! Videos will not always be in line with hardware on this page, this page will be the most updated for the build, and I will try to keep up with videos. The overall principles of the videos will remain the same. Please leave comments to help future builders.
# Complete Build
Complete Build with Choice primary color (not Black or Silver, 170 + Shipping), And optional k26 (+ 2 Dollares) and extrented Barrel (+ 4 Dollars),
# Hardware Kit
All Hardware Needed for the Build using M3 Screws (55 + Shipping)
# Minimal Hardware Kit, Specialty Pieces Only, (35 + Shipping)
# No Hardware Kit, Go Below, There is a list of all Hardware Needed and Techniques for and altered Metal Pieces!
Some parts can be replaced with Hardware store items. And probably be less expensive than an online order, Look at the required Hardware list at the bottom for options
Print Settings-WallThickness(WT) 1.8 WallCount(WC) 3 Top/Bottom Layer Thickness (T/BLT) 1.14 Top/Bottom Count 5 Infill 40%
3x M3 16mm -1x M3 20mm -1x M3 35mm
Print Settings-WallThickness(WT) 1.8 WallCount(WC) 3 Top/Bottom Layer Thickness (T/BLT) 1.14 Top/Bottom Count 5 Infill 40%
Clyinder housing. Orientation Matters for best perfomance Majority of volumue facing build plate
-17x M3 16mm 0r #4 5/8 Coarse Screws
-1x 35mm Length, 6mm OD, 0.6mm Wire Size spring
Filing down where the catch would meet the flickCatch helps performance
Print Settings-WallThickness(WT) 1.8 WallCount(WC) 3 Top/Bottom Layer Thickness (T/BLT) 1.14 Top/Bottom Count 5 Infill 40%
-1x 25mm Length, 6mm OD, 0.6mm Wire Size spring
-1x 35mm length, 9mm OD,0.6mm Wire Size spring
https://www.youtube.com/watch?v=dXDKxImVTaM&t=3s
To fit the springs put the grip and the cylinder housing together useing screws, then remove the fliclcatch insert springs and re-insert flickcatch using the 20mm screw
Print Settings-WallThickness(WT) 1.8 WallCount(WC) 3 Top/Bottom Layer Thickness (T/BLT) 1.14 Top/Bottom Count 5 Infill 80%
8x M3 8mm -2x M3 10mm
-1x 8mm length, 6mm OD,0.6mm Wire Size Spring
-1x 18mm length, 6mm OD,0.6mm Wire SizeSpring
https://www.youtube.com/watch?v=mL6fAB70G94
Print Settings-WallThickness(WT) 1.8 WallCount(WC) 3 Top/Bottom Layer Thickness (T/BLT) 1.14 Top/Bottom Count 5 Infill 80%
1x M3 35mm -2x M3 16mm -2x M3 8mm -1x M3 Nut -1x M3 ThumbScrew
-1x 8mm length, 6mm OD,0.6mm Wire Size Spring
https://www.youtube.com/watch?v=0L3rQnJ4SyA&t=10s
Print Settings-WallThickness(WT) 1.8 WallCount(WC) 3 Top/Bottom Layer Thickness (T/BLT) 1.14 Top/Bottom Count 5 Infill 80%
1x 75mm 6/32 Threaded Rod -2x 6/32 Locking Nut -2x M3 16mm
-1x 5mm OD 2mm ID 1.5mm Width Oring
-1x 3.1mm Wire Dia 24mm OD Oring
https://www.youtube.com/watch?v=LtRP3O0ix5Q
Print Settings-WallThickness(WT) 1.8 WallCount(WC) 3 Top/Bottom Layer Thickness (T/BLT) 1.14 Top/Bottom Count 5 Infill 40%
1x 170mm 6/32 Threaded Rod -4x 6/32 Locking Nuts
-1x 6mm OD,0.6mm Wire Size, 50mm length
-2x M3 16mm -2x M3 8mm
https://www.youtube.com/watch?v=eLsDKcdWpLc&t=1s
Filing down where the catch would meet the flickCatch helps performance
Print Settings-WallThickness(WT) 1.8 WallCount(WC) 3 Top/Bottom Layer Thickness (T/BLT) 1.14 Top/Bottom Count 5 Infill 40%
5x M3 8mm
-1x 3.1mm Wire Dia 24mm OD Oring
Print Settings-WallThickness(WT) 1.8 WallCount(WC) 3 Top/Bottom Layer Thickness (T/BLT) 1.14 Top/Bottom Count 5 Infill 40%
4x 6/32 Threaded Rod -4x 6/32 Locking Nuts -4x 6/32 Nuts -5x M3 35mm
-1x 14mm length, 6mm OD,0.6mm Wire Size,Spring
-6inch brass barrel 17/32" OD x 0.014" Wall (barrel needs a flare on one end)
-2x 15mm OD 11mm ID 2mm Width Oring
https://www.youtube.com/watch?v=pAxxv66oXxM
https://www.youtube.com/watch?v=pvPr4E7DJWI
Print Settings-WallThickness(WT) 1.8 WallCount(WC) 3 Top/Bottom Layer Thickness (T/BLT) 1.14 Top/Bottom Count 5 Infill 40%
1x M3 20mm Custom (head grinded) -1x 6/32 320mm Threaded Rod -2x 6/32 Nut -1x 6/32 Locking Nut
-1x 150mm Brass cover 4mm OD 0.2mm Wall Thickness
-84mm AirChamber Polycarbonate Tubing 1-3/8" ID, 1-1/2" OD, 1/16" Wall
-1x 5mm OD 2mm ID 1.5mm Width Oring
8mm - 17 or (or a Coarse Screws #4 x 3/8)
10mm - 2
16mm - 29 (or a Coarse Screws #4 x 5/8)
20mm - 1 (1 Filed Down) (or a Coarse Screws #4 x 5/8 fied down)
35mm - 2
Nut - 1
Thumb Screw 20mm - 1 (or 16mm M3 Must be an M3)
4x 160mm Threaded Rod
1x 170mm Threaded Rod
1x 320mm Threaded Rod
1x 75mm Threaded Rod
6x Nut
9x Locking Nut
2x 24mm OD 17.8mm ID 3.1mm Width Oring https://www.amazon.com/gp/product/B07YJDJJGV/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1
2x 15mm OD 11mm ID 2mm Width Oring https://www.amazon.com/gp/product/B07F352N1N/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1
2x 5mm OD 2mm ID 1.5mm Width Oring https://www.amazon.com/gp/product/B07D9NM1CJ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1
https://www.amazon.com/gp/product/B076LTYY5K/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
2x 8mm Length, 6mm OD,0.6mm Wire Size Spring
1x 12mm Length, 6mm OD,0.6mm Wire Size Spring
2x 50mm Length, 6mm OD,0.6mm Wire Size,50mm
1x 35mm Lenght, 9mm OD,0.6mm Wire Size spring
1x 6inch 7/32 brass tube (barrel)
1x 150mm length, 4mm OD 0.2mm Wall Thickness
1x Clear Polycarbonate Tubing, 4inch length, 1-3/8" ID, 1-1/2" OD, 1/16"
My First Working design, break action at the front
Two years later after other blaster, I moved the gear box inside the cylider
