Skip to content

Digital Microphone Hookup

Frank edited this page Feb 14, 2023 · 120 revisions

I2S Digital Audio

I2S digital sound modules utilize the industry-standard 24-bit I²S interface. The I²S interface allows to connect them directly to an ESP32 (but NOT an ESP8266). The INMP441, and also the recently tested ICS-43434 (thanks to Serg74) work very well with SR WLED, and they perform much better than any analog device at a comparable price.


from INMP441, ICS-43434 from PDM (e.g. SPM1423) from Other to ESP32 GPIO
L/R SEL SEL Gnd ground => left channel. Don't leave this pin unconnected!
SD DATA DOUT 32 serial data
WS CLK LRCK 15 left right clock
SCK -- BCLK 14 serial clock
-- -- MCLK 0 master clock (if needed)
VDD 3V3 VDD 3.3V power don't use 5V!
GND GND GND Gnd ground, 0V

Tip

ESP32 pins in the table are just examples. In fact any available GPIO can be used for I²S on ESP32.

  • SD can be either an in/out pin (gpio < 34) or an input-only pin (gpi >= 34),
  • while WS and SCK must be in/out pins (gpio < 34).

See also ⇒ Sound setting examples for common microphones


Microphone type (SR-WLED sound settings)

  • use Generic I2S for INMP441, ICS-43434, and other non-PDM devices
  • use Generic I2S PDM for PDM microphones like SPM1423
  • use SPH0645 for adafruit SPH0645
  • use ES7243 for Lyra-T mini, and other board that have the ES7243 chip
  • use Generic I2S with Mclk only for devices that have an addition pin for 'master clock'

Important: please make sure that your I2S device provides sound input on the LEFT audio channel! For the INMP441 this is achieved by wiring the 'L/R' connection to GND (ground). Only exception is the "ES7243" driver, which is always using the RIGHT audio channel.


Since 0.12.0, you can change I2S GPIO pins in the Sound Settings interface; on ESP32 any available GPIO (in-out pin) can be used for I²S. The 'SD' signal could also be mapped to an input-only (GPI) pin (*), if you are low on GPIO pins. You'll need to reboot when done with pin assignment - don't forget to "save". To reboot, please press 'reset' on your ESP32. Unfortunately a restart by software ("soft reboot") is not always sufficient to activate new driver settings.

In addition to I2S microphones, there are solutions available for line-in via I2S. We already have driver support for Boards/Shields with "es7243" chip, and we're investigating "es8388".

Other I2S ADC (analog-to-digital-converter) devices and microphones that have a standard I2S interface may already work with WLED-SR, by using one of the I2S "Generic" drivers (Generic I2S, Generic I2S PDM, or Generic I2S with Mclk). It is important however that sound input comes on the LEFT audio channel. Please keep in mind that this is a spare-time open source project - we do our best to make generic drivers but we cannot test with all available devices.

Notes for older releases of SR WLED (before 0.13.2)

  • (*) Due to a problem that was fixed very recently, its not possible to use input-only GPI pins in older releases of SR WLED. There will be no warning if you try to do so. This problem is solved in the latest release version of SR WLED.

  • In old releases, you need to change GPIO pins used by defining I2S_WS, I2S_SD, and I2S_SCK in your PlatformIO config, or by editing the values in audio_reactive.h.

Still having problems?

We do not have these digital microphones running on an ESP8266.

Having problems getting the INMP441 running with WLED? Here's a test sketch (which you can compile with the Arduino IDE): https://pastebin.com/Ua7s7LYF . If you are still having a problem with that sketch, change the line with ONLY_LEFT to ONLY_RIGHT. If that works, you'll need to go into audio_source.h and change that line.

Initial I2S support by @spedione


Some I2S audio modules and boards

INMP441

This is the INMP441; you can find it in many shops including Amazon and Aliexpress. It works very well with SR WLED.

 

 

ICS-43434

Here's the first board I've seen with the ICS-43434 at: https://www.tindie.com/products/serg74/digital-i2s-microphone-ics-43434-add-on/

 

I2S ADC for Line-In

Looking to add line-in with I2S support? You might want to try I2S ADC boards that use one of these chips:

 

       

Many I2S ADC boards expect an additional MCLK signal ("Main Clock" aka "System Clock" aka "Master Clock" aka "Memory Clock"). MCLK is sometimes labelled SCLK for "system clock". For these boards with 4 data pins, use our Generic I2S with MCLK input driver, and connect MCLK pin to GPIO pin 0, 1, or 3 on ESP32.

 

ES7243 based boards

 

ES8388 based boards - not yet supported

with I2S on-board microphone and I2S Line-In (SR WLED support not available yet, but being developed)

 

Other Ideas (needs some work to make it work)

use a second esp32 as bluetooth audio to I2S device

In principle, its possible to have a second ESP32 that provides sound input to WLED via I2S.

Clone this wiki locally