PS Vita streamer for ESP32 S3

First of all, I stopped this work because I could not go any further, I suspect that my esp32 s3 runs out of usage PSRam and just crashes.

So, what can you test in here. The main modifications are on the file: usb_stream.c This project originally created from Espressif expects a camera with MJPG format, and the PS vita outputs NV12 pixel format if you installed this extension on your device: https://github.com/xerpi/vita-udcd-uvc The version of esp-idf I used was: idf.py --version ESP-IDF v5.0 The main project is the modified project from: /esp-iot-solution/examples/usb/host/usb_camera_mic_spk

You need to compile the project specifying the next commands: idf.py set-target esp32s3 idf.py build esptool.py -p /dev/tty.usbserial-1110 -b 460800 --before default_reset --after hard_reset --chip esp32s3 write_flash --flash_mode dio --flash_size 2MB --flash_freq 80m 0x0 build/bootloader/bootloader.bin 0x8000 build/partition_table/partition-table.bin 0x10000 build/usb_camera_mic_spk.bin idf.py monitor -p /dev/tty.usbserial-1110 After that you can plug the PS vita and the ESP32 S3 would recognize it and will try to convert nv12 into jpg, if you dont do that, the ESP32 will send "pictures" but in nv12 format.

I was thinking you can catch them in the browser and make the conversion but I havent tried that yet

Espressif IoT Solution Overview

ESP-IoT-Solution contains device drivers and code frameworks for the development of IoT system, which works as extra components of ESP-IDF and much easier to start.

ESP-IoT-Solution contains following contents:

• Device drivers for sensors, display, audio, input, actuators, etc.
• Framework and documentation for Low power, security, storage, etc.
• Guide for espressif open source solutions from practical application point.

Documentation Center

• 中文：https://docs.espressif.com/projects/espressif-esp-iot-solution/zh_CN
• English:https://docs.espressif.com/projects/espressif-esp-iot-solution/en

Versions

ESP-IoT-Solution	Dependent ESP-IDF	Major Change	User Guide	Support State
master	release/v4.4	code structure change, add support for new chips	Docs online	active, new feature develop
release/v1.1	v4.0.1	IDF version update, remove no longer supported code	v1.1 Overview	limited support
release/v1.0	v3.2.2	legacy version	v1.0 Overview	archived

Quick Reference

Development Board

You can choose any of the ESP32/ESP32-S series development boards to use ESP-IoT-Solution, or choose one of the boards supported in boards component to quick start.

Powered by 40 nm technology, ESP32/ESP32-S series SOC provides a robust, highly integrated platform, which helps meet the continuous demands for efficient power usage, compact design, security, high performance, and reliability.

Setup Build Environment

Setup ESP-IDF Environment

ESP-IoT-Solution is developed based on ESP-IDF functions and tools, so ESP-IDF development environment must be setup first, you can refer Setting up Development Environment for the detailed steps.

Please note that different versions of ESP-IoT-Solution may depend on different versions of ESP-IDF, please refer to Versions for details.

Get ESP-IoT-Solution

• If select the master version, open terminal, and run the following command:

  git clone --recursive https://github.com/espressif/esp-iot-solution
  

• If select the release/v1.1 version, open terminal, and run the following command:

  git clone -b release/v1.1 --recursive https://github.com/espressif/esp-iot-solution
  

For other versions, replace release/v1.1 with the target branch name

Create Your Project

You can use the components of ESP-IoT-Solution in the following methods:

Method 1. Add all components' PATH of ESP-IoT-Solution to the project

Add the following code directly to the project's CMakeLists.txt:

cmake_minimum_required(VERSION 3.5)

include($ENV{IOT_SOLUTION_PATH}/component.cmake)
include($ENV{IDF_PATH}/tools/cmake/project.cmake)

project(empty-project)

Method 2. Add specified components' PATH of ESP-IoT-Solution to the project

Add the following code directly to the project's CMakeLists.txt, please add the REQUIRES components also:

set(EXTRA_COMPONENT_DIRS "${EXTRA_COMPONENT_DIRS} $ENV{IOT_SOLUTION_PATH}/components/{component_you_choose}")

Method 3. Copy specified components of ESP-IoT-solution to the project's components directory

Please copy the REQUIRES components together.

Note: CMake based build system is recommended (default in IDF v4.0 and later). If using GNU Make, you can refer legacy build system based on GNU Make.

Set up the environment variables

Add ESP-IDF environment variables:

• For Windows CMD terminal, run the following command:

  %userprofile%\esp\esp-idf\export.bat
  

• For Linux or macOS terminal, run the following command:

  . $HOME/esp/esp-idf/export.sh
  

Add IOT_SOLUTION_PATH environment variables:

• For Windows CMD terminal, run the following command:

  set IOT_SOLUTION_PATH=C:\esp\esp-iot-solution
  

• For Linux or macOS terminal, run the following command:

  export IOT_SOLUTION_PATH=~/esp/esp-iot-solution
  

Note:

1. Please replace the example path with your actual installation path.
2. The environment variables set above only valid for the current terminal. please re-run the command if open new terminal.

Resources

• Documentation for the latest version:https://docs.espressif.com/projects/espressif-esp-iot-solution/ . This documentation is built from the docs directory of this repository.
• ESP-IDF Programming Guide: https://docs.espressif.com/projects/esp-idf/zh_CN . Please refer to the version ESP-IoT-solution depends on.
• The esp32.com forum is a place to ask questions and find community resources.
• Check the Issues section on github if you find a bug or have a feature request. Please check existing Issues before opening a new one.
• If you're interested in contributing to ESP-IDF, please check the Contributions Guide.