-
Notifications
You must be signed in to change notification settings - Fork 1.2k
New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
Board does not boot anymore #20
Comments
Did You check fuses? |
Hello ! |
Disconnect all connectors, remove stepstics and connect directly to PC (switch jumper to USB +5V). |
Hello Artur, Connecting to: /dev/ttyAMA0Changing monitoring state from "Offline" to "Opening serial port"Connected to: Serial<id=0x6abad110, open=True>(port='/dev/ttyAMA0', baudrate=115200, bytesize=8, parity='N', stopbits=1, timeout=10.0, xonxoff=False, rtscts=False, dsrdtr=False), starting monitorStarting baud rate detection...Changing monitoring state from "Opening serial port" to "Detecting baudrate"Trying baudrate: 115200 |
Hello, did you have config for ender5? I got new skr1.3 but it wont bootup eith mine config, can you please give yours to try |
yes sure.
Am Sa., 18. Mai 2019 um 16:00 Uhr schrieb archikkk <notifications@github.com
…:
Hello, did you have config for ender5? I got new skr1.3 but it wont bootup
eith mine config, can you please give yours to try
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub
<#20?email_source=notifications&email_token=AL67S2SZXVMFYTCHASPA2J3PWADWNA5CNFSM4HJ44A42YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGODVWPFNY#issuecomment-493679287>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AL67S2VGRRUVNO6PLP2CMZDPWADWNANCNFSM4HJ44A4Q>
.
|
Hi, did you solve the problem? I'm having the same issue... |
No, had to buy a new board.... Sorry bro
signorecello <notifications@github.com> schrieb am So., 13. Okt. 2019,
14:43:
… Hi, did you solve the problem? I'm having the same issue...
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub
<#20?email_source=notifications&email_token=AL67S2QAPYO3FIVWUT4VNHTQOMJYVA5CNFSM4HJ44A42YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEBCVPWQ#issuecomment-541415386>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AL67S2WB6OGJWNUUNIOQV23QOMJYVANCNFSM4HJ44A4Q>
.
|
looks like some boards have the EXP1 and EXP2 bad oriented, check the pinout to confirm. |
Hello !
Everything went fine with my new skr 1.3 ( Marlin 2.X ( Ender 5 ) for about 20 prints.
Suddenly when i start my printer i get a constant beep tone and
a blue screen ( Stock Creality screen).
So i disconnected everything switched to 5v jumper and tried to recompile the firmware as usual via PlatformIO.
I get the error "board not found". ( But it shows up normally under windows 7 )
I am thankful for every hint, thank you in Advance !
The text was updated successfully, but these errors were encountered: