GENELDE HP WİFİ rtl8723be OLAN BİLGİSAYARLARA UBUNTU YÜKLEDİKTEN SONRA OLUŞAN WİFİ SİNYAL SORUNUNUN ÇÖZÜMÜ (AŞAĞIDAKİ YAZILAR ANLAŞILMIYOR :D BENİM YÖNERGELERİ TAKİP ETMENİZİ TAVSİYE EDERİM :D)
git clone https://github.com/lwfinger/rtlwifi_new.git
cd rtlwifi_new
make
sudo make install
sudo modprobe -rv rtl8723be
sudo modprobe -v rtl8723be ant_sel=2
sudo ip link set wlp2s0 up// (wlp2s0 örnek wireless sürücü kodudur. ifconfig yazarak wlp.s0 ın hangisi olduğunu bulabiliriz.)
sudo iw dev wlp2s0 scan
ayarların kalıcı olarak kalmasını istiyorsak
echo "options rtl8723be ant_sel=2" | sudo tee /etc/modprobe.d/50-rtl8723be.conf
komutlarını yazıyoruz ve wifi sinyalimiz full çekiyor.
This code will build on any kernel 4.2 and newer as long as the distro has not modified any of the kernel APIs. IF YOU RUN UBUNTU, YOU CAN BE ASSURED THAT THE APIs HAVE CHANGED. NO, I WILL NOT MODIFY THE SOURCE FOR YOU. YOU ARE ON YOUR OWN!!!!!
Note: If your kernel is 4.17 or newer, AND your card is not an RTL8723DE, then you should NOT be using the external driver. The built-in one is the same.
It includes the following drivers:
rtl8192ce, rtl8192cu, rtl8192se, rtl8192de, rtl8188ee, rtl8192ee, rtl8723ae, rtl8723be, rtl8821ae, rtl8822be and rtl8723de.
You can find <> using lspci | grep Wireless.
Afterwards, execute the following lines of codes in your shell:
You will need to install "make", "gcc", "kernel headers", "kernel build essentials", and "git".
If you are running Ubuntu, then
sudo apt-get install linux-headers-generic build-essential git
Please note the first paragraph above.
For all distros:
git clone https://github.com/lwfinger/rtlwifi_new.git
cd rtlwifi_new
make
sudo make install
sudo modprobe -r <<YOUR WIRELESS DRIVER CODE>>
sudo modprobe <<YOUR WIRELESS DRIVER CODE>>
#### Option configuration
If it turns out that your system needs one of the configuration options, then do the following:
sudo vim /etc/modprobe.d/<<YOUR WIRELESS DRIVER CODE>>.conf
There, enter the line below:
`options <<YOUR WIRELESS DRIVER CODE>> <<driver_option_name>>=<value>`
The ONLY option you are likely to need is "ant_sel". The penny-pinchers at some laptop vendors,
mostly HP, decided to save a few cents to install only one antenna. That would not have been a
problem as the driver contains the logic necessary to handle this case; however, the idiots
failed to correrctly encode that information in the devices ROM. Accordingly, the driver follow
the ROM setting and uses the WRONG antenna. Effectively, the device has NO usable antennas. To test
if this is the case on your system, please run the following commands (set 1):
DEVICE=$(iw dev | grep Interface | cut -d " " -f2)
sudo iw dev $DEVICE scan | egrep "SSID|signal|\(on"
If the signal for the AP to which you wish to connect is -60 or less, then you have this problem.
The fix is to supply the "ant_sel" option. Run the following commands (set 2):
sudo su -
echo "options rtl8723be ant_sel=2" > /etc/modprobe.d/50-rtl8723be.conf
exit
If you have an RTL8723DE, make the appropriate adjustments to the above command.
At this point, do a complete shutdown! The device may retain the old setting with a warm reboot.
To be safe, do a power off. After the system come back up, rerun the set 1 comamands again. If
The signals are now a lot stronger, you are done. If not, repeat command set 2 with "ant_sel=1".
If that does not help, I have no idea what is wrong.