Skip to content

Latest commit

 

History

History
107 lines (62 loc) · 5.08 KB

wired-ethernet.md

File metadata and controls

107 lines (62 loc) · 5.08 KB

Wired Ethernet

Several boards are available with ethernet hardware, which can be used as drop-in replacements for ESP8266 / ESP32 WiFi modules and are compatible with all models of OpenEVSE / EmonEVSE.

See OpenEnergyMonitor web-store to purchase a pre-wired ESP32-Gateway module. The Ethernet gateway in our web-store will come with pre-wired power supply, serial connections, and pre-loaded with firmware for drop in replacement.

esp32-gateway-prewired

Network connection can be made with a standard Ethernet cable. For new installations it may be worth considering a power cable with integrated data connections such as the Doncaster EV-ultra cable. If using such a cable, extra work will be required to attach RJ45 connector or socket at each end.

Hardware Connections

Wiring varies depending on the board in use, in particular this git issue discusses a wiring change between revisions of the ESP32-GATEWAY board.

Signal EVSE wire ESP32-GATEWAY E & F ESP32-GATEWAY pre-E ESP32-PoE-ISO
5V Red wire 20 20 N/C (powered over Ethernet)
GND Black wire 19 19 GND
Tx GPIO 32 Yellow wire 13 12 33
Rx GPIO 16 Green wire 11 11 35

See photos of hardware connectors for new OpenEVSE V5.5 controller.

Note: The these hardware connections apply to the current Rev.E & Rev.F ESP32-gateway hardware revisions. See table above for other units.

esp32-gateway-connections

The ESP32-gateway can be installed in the EmonEVSE as follows:

esp32-gateway-emonevse

Firmware

ESP32-gateway modules from the OpenEnergyMonitor store come pre-loaded with firmware. Updates to firmware can be made via the web interface.

Uploading pre-compiled

Pre-compiled FW can be downloaded from the repo releases page, look for esp32-gateway-e.bin

ESP32-gateway can be connected by micro USB and firmware can be uploaded using esptool:

For rev E

First upload:

esptool.py --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 40m --flash_size detect 0x1000 bootloader.bin 0x8000  partitions.bin 0x10000  olimex_esp32-gateway-e.bin

Subsequent upgrades:

esptool.py --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 40m --flash_size detect 0x1000 olimex_esp32-gateway-e.bin

Note: On Ubuntu 22.04 if you notice the ESP gateway is continually disconnect from the USB serail port,check this using dmesg thensudo apt remove brltty will fix this. This is because there is an ebook reader which shares the same serial adaptor chip as the ESP gateway and the udev rules conflict.

For Ubuntu 22.04 the simplest solution is to remove the package brltty via sudo apt remove brltty

For rev F/G

First upload:

esptool.py --before default_reset --after hard_reset write_flash  0x1000 bootloader.bin 0x8000 partitions.bin 0x10000 olimex_esp32-gateway-f.bin

Subsequent upgrades:

esptool.py --before default_reset --after hard_reset write_flash 0x10000 olimex_esp32-gateway-f.bin`

Compile and Upload

Board Environment
ESP32-GATEWAY pre-E olimex_esp32-gateway
ESP32-GATEWAY E and later olimex_esp32-gateway-e
ESP32-PoE-ISO olimex_esp32-poe-iso

Firmware can be compiled using PlatformIO pio run -e <Environment>. The -t upload option installs firmware over USB.

pio run -e olimex_esp32-gateway-e -t upload

Operation

The ESP32-gateway supports both WiFi and Ethernet, if an Ethernet cable is not connected the ESP32-gateway will broadcast a WiFi AP OpenEVSE_xxx, connect with Passkey openevse.

When an Ethernet cable is connected WiFi will be disabled and the local network IP address and hostname displayed on the LCD.

NOTE: Static IP or custom gateway IP address settings are currently not supported.

The web UI will notify that connection is via Wired Ethernet.

esp32-gateway-connected

Feedback

The ESP32-Gateway is a new addition and is currently considered in 'Beta' since the ESP32 firmware is still under active development. However, it has been extensively tested and proven reliable for many months of operation. Please report your experience to the OpenEnergyMonitor Community Forums.