Wattio Smart Home

Wattio Smart Home platform integration for Home Assistant throught Wattio's API. This component is under development.

Currently Supported Devices: Bat, Thermic, Motion, Door, Pod and Siren

You can use this devices via HomeKit using Home Assistant's HomeKit bridge (Bat is not supported right now).

---

Changelog

Please check CHANGELOG.md for full details.

[0.2.13] - 2021-06-04

Fixed

• Reuploaded fix for #9
• Minor fix: CONF_SECURITY_INTERVAL variable is optional again

[0.2.12] - 2021-06-03

Changed

• Simple offset support based on #13 comments

[0.2.11] - 2021-06-03

Added

• Offset support for power sensors

Fixed

• Security device status not getting current state from Wattio API (#9)

[0.2.10] - 2021-05-19

Tested on HASS 2021.5.4

Fixed

• #9 Fixed async errors on device status set commands on Hass >2021.4.3
• Restored debugging messages for security devices

Changed

• Migrated all methors from requests to async aiohttp

[0.2.9] - 2021-04-14

Fixed

• #8 Fixed initial configuration notifications due to use of deprecated base_url

[0.2.8] - 2021-01-20

Added

• You can now skip adding some devices to HASS using sensor_exclude config entry

[0.2.7] - 2021-01-13

Fixed

• Time attribute of climate was not updating correctly (old file uploaded to the repo)

[0.2.6] - 2021-01-11

Added

• Consumption attribute added to switch entity. Leaving switch independent consumption sensor for backwards compatibility.
• HACS Support! Now you can install / upgrade this component via HACS :)

Fixed

• Some console output (error leven) has been changed to its correct level.

---

Installation

Pre-Requisites

• Client ID and Secret for Wattio Platform (Request to wattio Support)
• Works on Home Assistant >= 0.90.2 (Tested up to 2021.1.1)

HACS (Prefered)

• If you have previously installed this component manually, please remove it, but keep your wattio.conf file so you don't have to setup the platform again.
• Search for Wattio integration in HACS and install it.
• Follow adittional configuration steps.

Manual Installation

• Copy "wattio" folder to your <config dir>/custom_components/wattio directory.
• Configure as shown below.
• Restart HASS.
• Follow the adittional configuration steps.

Configuration

Add the following to your configuration.yaml.

From version 0.2.0 the way of Wattio component is configured has been changed. If you are upgrading for a previous version you MUST CHANGE YOUR CONFIG FILE

# Wattio Platform
wattio:
  scan_interval: 60
  security: true
  security_interval: 300
  sensor_exclude: ['ieee1']
  sensor_offsets: >
    [
      {
        'sensor_iee': 'ieee',
        'sensor_name': 'sensor_name',
        'sensor_offset': 30,
      },
    ]

Vars:

Var	Description
scan_interval	OPTIONAL - Time (in seconds) between data updates , defaults to 30 seconds
security	OPTIONAL - Enable or disable security devices, defaults to False
security_interval	OPTIONAL - Time (in seconds) between security devices data updates, defaults to scan_interval
sensor_exclude	OPTIONAL - List with IEEEs to exclude, for example: ["ieee1","ieee2"]
sensor_offsets	OPTIONAL - List with offsets for sensors

Adittional steps

• At first launch a new notification is shown at the UI requesting the user to configure de user id and the secret.

• The configuration file "wattio.conf" is created automatically.

• Change user id and secret in "wattio-conf".

  User id and secret MUST be supplied by wattio team (This is not your user and password!)

• After changing the configuration file, another notification should appear asking the user to authorize home assistant at wattio.

• Follow the link for authorization, a page requesting username and password from Wattio should be shown.

• Finally, close the notification and refresh your GUI.

• Once devices has been added to HASS, first data update will take place after the configured scan_interval.