- WebUI optimizations, updated look&feel and better performance #124
- Auto refresh of WebUI after successful firmware upload #178
- New Customization Service in WebUI. First feature is the ability to enable/disabled Enitites (device values) from EMS devices #206
- Option to disable Telnet Console #209
- Added Hide SSID, Max Clients and Preferred Channel to Access Point
- Merged in MichaelDvP's changes like Fahrenheit conversion, publish single (for IOBroker) and a few other critical optimizations
- Enabled bi-directional read/write with Home Assistant, so values can be changed automatically from the UI without scripting #265
- Added GC7000F Boiler #270
- Revised LED flash sequence on boot up to show system health (1 flash=no ems, 2 flashes=no wifi) #224
- Analog Sensor support #271
- Solar cylinder priority #247
- Read only mode in Settings, where EMS Tx/Write commands are blocked #286
- Added 8700i Boiler device
- Added Cascade CM10 Controller device
- Add Olimex ESP32-POE-ISO to board profiles plus settings to customize Ethernet modules #301
- Help text for string commands in WebUI #320
- Germany translations (at compile time)
- #entities added to system/info` endpoint #322
- analog outputs digital/pwm/dac
- remove MQTT retained configs if discovery is disabled
- timeout 10 min for MQTT-QoS wait
- Moduline 300 auto-temperatures T1-T4, RC300 romminfluencefactor
- RC35 parameters #392, #398
- sync time with thermostat #386, #408
- set mode has immediate effect #395
- min/max in web value setting
- Extend customization to select if an entity is to be shown in the WebUI or forced as read-only #317
- Added Moduline 400 installation parameters PR #449 by @kwertie01
- Read time from IVT-controller #439
- Hybrid Heatpump product-id 168 #459, thermostat settings
- Junkers ISM2 and IPM in warm water mode #437
- Added Shower Alert trigger time and cold shot time #436
- Improved Table layout in Web UI (searching, filtering, sorting, exporting to CSV)
- API fetch individual attributes from an entity #462
- Option to disable mDNS
- Option for rendering booleans on dashboard #456
- lastcode broke MQTT JSON structure #228
- fixed issue with overlapping while reading sequence of EMS1.0 telegrams
- fixed redundant telegram readings (because of offset overflow)
- added missing RC30/Moduline 400 #243
- Correct modes for RC25 #106
- Clean up old HA config's in MQTT before publishing data. This will prevent HA giving the 'dict' warnings #229
- RC25 temperature setting #272
- Buderus RC25 - "hc1 mode type" incorrect value #273
- Increased number of Mixers and Heating Circuits #294
- Check receive status before removing a telegram fetch #268, #282
- Fix uploading firmware on OSX #345
- Non-nested MQTT would corrupt the json #354
- Burner selected max power can have a value higher than 100% #314
- some missing fahrenheit calculations
- limited number of exclusions #339
- MQTT sometimes would not reconnect after a WiFi outage
- Use flash system to show system health (1 flash=no ems, 2 flashes=no wifi) #224
- Renamed Dallas Sensor to Temperature Sensor in UI
- Dallas Format removed. Use the name to give each sensor an alias
- No longer MQTT subscribes to topic
/thermostat_hc<n>
as it supports a path similar to the API endpoint construct - Show Sensors quality in WebUI
- Controller not shown in WebUI dashboard
- renamed "Home Assistant Integration" to "MQTT Discovery" in MQTT Settings #290
- Show ems tx reads and writes separately
- Show ems device handlers separated for received, fetched and pending handlers.
- Wired renamed to Ethernet
- removed system/pin command, new commands in analogsensors
- system/info device-info split to name/version/brand
- exclude list uses short-names, possible flags for web/api/mqtt excludes, readonly and favorite (selection not yet implemented)
- thermostat clock formate date-time: dd.mm.yyyy hh:mm
- RC300 summermode as other thermostats
winter/summer
instead ofoff/on
- Settings:
- order of Boolean Format has changed in Application Settings - check your settings
- Dallas Format setting removed. Now customize name of each Dallas sensor via the UI
- MQTT/API
- Boiler
wwheat
renamed toww3wayon
#211 - Boiler
ww
tag renamed todhw
. Any custom Home Assistant lovelace dashboards will need updating. - Renamed description of
wwtapactivated
to "turn on/off DHW". Otherwise would have looked like "boiler_dhw_turn_on_off_dhw" in HA. /api/system/info
endpoint has updated keys. Now lowercase, no underscores and not capitalized. Replace "handlers" with "handlers received", "handlers fetched" and "handlers pending".
- Boiler