Merge branch 'bugfix/usb_host_enumeration_delay_v4.4' into 'release/v…

…4.4'

USB Host: SetAddress recovery interval + menuconfig configuration (backport v4.4)

See merge request espressif/esp-idf!22703

components/usb/Kconfig

@@ -53,4 +53,58 @@ menu "USB-OTG"
             bool "Periodic OUT"
     endchoice
 
+    menu "Root Hub configuration"
+
+        config USB_HOST_DEBOUNCE_DELAY_MS
+            depends on USB_OTG_SUPPORTED
+            int "Debounce delay in ms"
+            default 250
+            help
+                On connection of a USB device, the USB 2.0 specification requires a "debounce interval with a minimum
+                duration of 100ms" to allow the connection to stabilize (see USB 2.0 chapter 7.1.7.3 for more details).
+                During the debounce interval, no new connection/disconnection events are registered.
+
+                The default value is set to 250 ms to be safe.
+
+        config USB_HOST_RESET_HOLD_MS
+            depends on USB_OTG_SUPPORTED
+            int "Reset hold in ms"
+            default 30
+            help
+                The reset signaling can be generated on any Hub or Host Controller port by request from the USB System
+                Software. The USB 2.0 specification requires that "the reset signaling must be driven for a minimum of
+                10ms" (see USB 2.0 chapter 7.1.7.5 for more details).  After the reset, the hub port will transition to
+                the Enabled state (refer to Section 11.5).
+
+                The default value is set to 30 ms to be safe.
+
+        config USB_HOST_RESET_RECOVERY_MS
+            depends on USB_OTG_SUPPORTED
+            int "Reset recovery delay in ms"
+            default 30
+            help
+                After a port stops driving the reset signal, the USB 2.0 specification requires that the "USB System
+                Software guarantees a minimum of 10 ms for reset recovery" before the attached device is expected to
+                respond to data transfers (see USB 2.0 chapter 7.1.7.3 for more details). The device may ignore any
+                data transfers during the recovery interval.
+
+                The default value is set to 30 ms to be safe.
+
+
+        config USB_HOST_SET_ADDR_RECOVERY_MS
+            depends on USB_OTG_SUPPORTED
+            int "SetAddress() recovery time in ms"
+            default 10
+            help
+                "After successful completion of the Status stage, the device is allowed a SetAddress() recovery
+                interval of 2 ms. At the end of this interval, the device must be able to accept Setup packets
+                addressed to the new address. Also, at the end of the recovery interval, the device must not respond to
+                tokens sent to the old address (unless, of course, the old and new address is the same)." See USB 2.0
+                chapter 9.2.6.3 for more details.
+
+                The default value is set to 10 ms to be safe.
+
+
+    endmenu #Root Hub configuration
+
 endmenu #USB-OTG

components/usb/hcd_dwc.c

@@ -29,9 +29,9 @@
 // --------------------- Constants -------------------------
 
 #define INIT_DELAY_MS                           30  //A delay of at least 25ms to enter Host mode. Make it 30ms to be safe
-#define DEBOUNCE_DELAY_MS                       250 //A debounce delay of 250ms
-#define RESET_HOLD_MS                           30  //Spec requires at least 10ms. Make it 30ms to be safe
-#define RESET_RECOVERY_MS                       30  //Reset recovery delay of 10ms (make it 30 ms to be safe) to allow for connected device to recover (and for port enabled interrupt to occur)
+#define DEBOUNCE_DELAY_MS                       CONFIG_USB_HOST_DEBOUNCE_DELAY_MS
+#define RESET_HOLD_MS                           CONFIG_USB_HOST_RESET_HOLD_MS
+#define RESET_RECOVERY_MS                       CONFIG_USB_HOST_RESET_RECOVERY_MS
 #define RESUME_HOLD_MS                          30  //Spec requires at least 20ms, Make it 30ms to be safe
 #define RESUME_RECOVERY_MS                      20  //Resume recovery of at least 10ms. Make it 20 ms to be safe. This will include the 3 LS bit times of the EOP
 

components/usb/hub.c

@@ -32,6 +32,8 @@ implement the bare minimum to control the root HCD port.
 #define HUB_ROOT_HCD_PORT_FIFO_BIAS                 HCD_PORT_FIFO_BIAS_BALANCED
 #endif
 
+#define SET_ADDR_RECOVERY_INTERVAL_MS               CONFIG_USB_HOST_SET_ADDR_RECOVERY_MS
+
 #define ENUM_CTRL_TRANSFER_MAX_DATA_LEN             CONFIG_USB_HOST_CONTROL_TRANSFER_MAX_SIZE
 #define ENUM_DEV_ADDR                               1       //Device address used in enumeration
 #define ENUM_CONFIG_INDEX                           0       //Index of the first configuration of the device
@@ -79,6 +81,7 @@ typedef enum {
     ENUM_STAGE_SECOND_RESET,                /**< Reset the device again (Workaround for old USB devices that get confused by the previous short dev desc request). */
     ENUM_STAGE_SET_ADDR,                    /**< Send SET_ADDRESS request */
     ENUM_STAGE_CHECK_ADDR,                  /**< Update the enum pipe's target address */
+    ENUM_STAGE_SET_ADDR_RECOVERY,           /**< Wait SET ADDRESS recovery interval at least for 2ms due to usb_20, chapter 9.2.6.3 */
     ENUM_STAGE_GET_FULL_DEV_DESC,           /**< Get the full dev desc */
     ENUM_STAGE_CHECK_FULL_DEV_DESC,         /**< Check the full dev desc, fill it into the device object in USBH. Save the string descriptor indexes*/
     ENUM_STAGE_GET_SHORT_CONFIG_DESC,       /**< Getting a short config desc (wLength is ENUM_SHORT_DESC_REQ_LEN) */
@@ -117,6 +120,7 @@ const char *const enum_stage_strings[] = {
     "SECOND_RESET",
     "SET_ADDR",
     "CHECK_ADDR",
+    "SET_ADDR_RECOVERY",
     "GET_FULL_DEV_DESC",
     "CHECK_FULL_DEV_DESC",
     "GET_SHORT_CONFIG_DESC",
@@ -411,6 +415,22 @@ static bool enum_stage_transfer(enum_ctrl_t *enum_ctrl)
     return true;
 }
 
+static bool enum_stage_wait(enum_ctrl_t *enum_ctrl)
+{
+    switch (enum_ctrl->stage) {
+        case ENUM_STAGE_SET_ADDR_RECOVERY: {
+            vTaskDelay(pdMS_TO_TICKS(SET_ADDR_RECOVERY_INTERVAL_MS)); // Need a short delay before device is ready. Todo:   IDF-7007
+            return true;
+        }
+
+        default:    //Should never occur
+            abort();
+            break;
+        }
+
+    return false;
+}
+
 static bool enum_stage_transfer_check(enum_ctrl_t *enum_ctrl)
 {
     //Dequeue the URB
@@ -696,6 +716,7 @@ static void enum_set_next_stage(enum_ctrl_t *enum_ctrl, bool last_stage_pass)
         case ENUM_STAGE_GET_SHORT_DEV_DESC:
         case ENUM_STAGE_SECOND_RESET:
         case ENUM_STAGE_SET_ADDR:
+        case ENUM_STAGE_SET_ADDR_RECOVERY:
         case ENUM_STAGE_GET_FULL_DEV_DESC:
         case ENUM_STAGE_GET_SHORT_CONFIG_DESC:
         case ENUM_STAGE_GET_FULL_CONFIG_DESC:
@@ -857,6 +878,10 @@ static void enum_handle_events(void)
         case ENUM_STAGE_GET_FULL_SER_STR_DESC:
             stage_pass = enum_stage_transfer(enum_ctrl);
             break;
+        //Recovery interval
+        case ENUM_STAGE_SET_ADDR_RECOVERY:
+            stage_pass = enum_stage_wait(enum_ctrl);
+            break;
         //Transfer check stages
         case ENUM_STAGE_CHECK_SHORT_DEV_DESC:
         case ENUM_STAGE_CHECK_ADDR: