-
Notifications
You must be signed in to change notification settings - Fork 1
/
parameters.hpp
97 lines (65 loc) · 3.3 KB
/
parameters.hpp
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
/*
This file is part of Orto idroponico Fablab Imperia
Orto idroponico Fablab Imperia is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
Nome-Programma is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with Nome-Programma. If not, see <http://www.gnu.org/licenses/>.
*/
// Include for external Adafruit ADC
#include <Adafruit_ADS1X15.h>
#ifndef DEVICE_PARAMETERS
#define DEVICE_PARAMETERS
// WiFi network SSID and PASSWORD
#define ORTO_WEB_SSID_BASENAME "OrtoWeb"
#define ORTO_WEB_SSID_PASSWD "OrtoWeb12345"
// ADC type: define the correct type of ADC (ADS1015 is a 12 bit resolution ADC, ADS1115 is a 16 bit ADC)
//#define ADC_ADS1015
#define ADC_ADS1115
#define LCD_I2C_ADDRESS 0x27
#define LCD_ROWS 4
#define LCD_COLS 20
// Update time of sensors shown in display
#define TIME_BETWEEN_DISPLAY_VALUES 1000
// After MANUAL_CONTROL_PUMP_TIMEOUT ms all pumps will be turned off (without any other command)
#define MANUAL_CONTROL_PERISTALTIC_PUMP_TIMEOUT 500
// Debug serial communication baudrate
#define SERIAL_BAUDRATE 115200
// Usually you don't need to edit the parameters below (if you use the same hardware)
// EEPROM used size, see eeprom.ino
#define EEPROM_USED_SIZE 15
/* ATTENTION! DEFAULT VALUES ARE DEPRECATED! *
Use web interface to set parameters at runtime
Parameters will be saved into internal EEPROM
and retrived at startup */
// Duration of one water pump cycle in seconds, set to 0 to keep the pump always on
#define DEFAULT_TIME_WATER_PUMP_CYCLE (0) // Put brackets around expressions like (60*60) [1 hour] because of operator precedence
// Time in seconds of water pump activity in a complete cycle (it's ignored if TIME_WATER_PUMP_CYCLE is zero)
#define DEFAULT_TIME_WATER_PUMP_ACTIVE 15 // Put brackets around expressions like (60*60) [1 hour] because of operator precedence
//Time the acid and fertilizer pumps remain ON acter activation in ms
#define DEFAULT_TIME_PERISTALTIC_PUMP_ON 1*1000L
//Time in seconds between two consecutives sensor reads. If the value is below/up the the threshold the pump is acivated (acid or fertlizer)
#define DEFAULT_TIME_BETWEEN_SENSOR_READS 60
//PH Threshold vale (if sensor value is higher, acid pump turns ON)
#define DEFAULT_THRESHOLD_VALUE_PH 6
//PH Threshold vale (if value is higher, acid pump turns ON)
#define DEFAULT_THRESHOLD_VALUE_CONDUCTIVITY 900
#ifdef ADC_ADS1015
#define ADC_MAX_VALUES 2047 // 2^(12-1) - 1
#elif defined(ADC_ADS1115)
#define ADC_MAX_VALUES 32767 // 2^(16-1) - 1
#endif
#define ADC_MAX_VOLTAGE 6.144
#ifdef ADC_ADS1115
#define ADAFRUIT_ADC Adafruit_ADS1115
#elif defined(ADC_ADS1015)
#define ADAFRUIT_ADC Adafruit_ADS1015
#else
#error "No ADC type definition, define the used type in parameters.hpp (https://github.com/fablab-imperia/orto-idroponico)";
#endif*/
#endif