nrf24-multipro integrated with payne_rc

nRF24L01 multi-protocol RC transmitter

see the transmitter see the channel order see the schematics

Binding Procedure

• Power up quad or receiver.
• While holding the appropriate stick pattern listed below, power up the tranmitter. ( that means protocol selected)
• Then move Throttle stick down ( enter binding)
• when bind done the radio will beep, watch to see if thequad/receiver is in the right status.

Protocol is selected with stick position at startup:

• Rudder left + Aileron left = Bayang protocol without Silverware telemetry for OpenTX
• Rudder right + Aileron right + Elevator down = EAchine E010, NiHui NH-010, JJRC H36 mini
• Rudder right + Aileron right + Elevator up = FQ-777-124 Pocket Drone
• Rudder right + Aileron left + Elevator up = CX-10 older red PCB/CX11/CX205/CX30, JXD389/391/393, SH6057/6043/6044/6046/6047, FY326Q7, WLToys v252 Pro/v343, XinXun X28/X30/X33/X39/X40
• Rudder right + Aileron left + Elevator down = WLToys V930/931/939/966/977/988
• Rudder right + Elevator down = HiSky RXs, HFP80, HCP80/100, FBL70/80/90/100, FF120, HMX120, WLToys v933/944/955
• Rudder right + Elevator up = Syma X5C (older model), X2 ...
• Rudder right + Aileron right = MJX X600
• Rudder right + Aileron left = EAchine H8 mini 3D, JJRC H20/H22
• Elevator down + Aileron left = Syma X5C-1/X11/X11C/X12
• Elevator down + Aileron right = Attop YD-822/YD-829/YD-829C ...
• Elevator up + Aileron right = EAchine H8(C) mini, BayangToys X6/X7/X9, JJRC JJ850, Floureon H101, BWhoop B03 ...
• Elevator up + Aileron left = EAchine H7
• Elevator up = WLToys V202/252/272, JXD 385/388, JJRC H6C, Yizhan Tarantula X6 ...
• Elevator down = EAchine CG023/CG031/3D X4
• Aileron left = Cheerson CX-10 green pcb
• Aileron right = Cheerson CX-10 blue pcb & some newer red pcb, CX-10A, CX-10C, CX11, CX12, Floureon FX10, JJRC DHD D1
• Rudder left = Renew Transmitter ID

Last used protocol is automatically selected if stick is in neutral position ( throttle must in low postions)

Extra features (if available on aircraft):

• Channel 5: led light, 3 pos. rate on CX-10 and FQ777-124, H7, inverted flight on H101
• Channel 6: flip control
• Channel 7: still camera
• Channel 8: video camera, pitch trim (FQ777-124)

Control 4-8 Channel on Radio

• Channel 5: the knob
• Channel 6: holding F1 and F2 both, then presss down 2 btn on the right. do it again (the CH vale will be switch from PWM 1000 and 2000us)
• Channel 7: holding F1 and F2 both, then presss down 3 btn
• Channel 8: holding F1 and F2 both, then presss down 4 btn

Trim

• Channel 1 Aileron: use btn 3 or 4
• Channel 2 Elevator: use btn 1 or 2
• Channel 3 Throttle : holding F1 , then press 1 or 2
• Channel 4 Rudder : holding F1 , then press 3 or 4

Channel reverse

• Channel 1 Aileron: holding F1 , then press 1
• Channel 2 Elevator: holding F1 , then press 2
• Channel 3 Throttle : to avoid confusion, not support reverse
• Channel 4 Rudder : holding F1 , then press 4

Channel precent

• Channel 1 Aileron: move Stick of Aileron to 70% position (left or right is the same) , then press both F1 and F2 down. then range is reduce to 70%
• Channel 2 Elevator: just like Channel 1
• Channel 4 Rudder : just like Channel 1

Channel Setting Reset (trim, reverse, precent)

Let Throttle stick up, after that, holding F1 and F2 both, then press 1. a beep will inform that reset is done.