Skip to content
This repository
tree: bfb05fc1f2
Fetching contributors…

Cannot retrieve contributors at this time

file 126 lines (105 sloc) 5.457 kb
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126
/*
config.h - compile time configuration
Part of Grbl

Copyright (c) 2009-2011 Simen Svale Skogsrud
Copyright (c) 2011 Sungeun K. Jeon

Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.

Grbl is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.

You should have received a copy of the GNU General Public License
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
*/

#ifndef config_h
#define config_h

// IMPORTANT: Any changes here requires a full re-compiling of the source code to propagate them.

#define BAUD_RATE 9600

// Updated default pin-assignments from 0.6 onwards
// (see bottom of file for a copy of the old config)

#define STEPPERS_DISABLE_DDR DDRB
#define STEPPERS_DISABLE_PORT PORTB
#define STEPPERS_DISABLE_BIT 0

#define STEPPING_DDR DDRD
#define STEPPING_PORT PORTD
#define X_STEP_BIT 2
#define Y_STEP_BIT 3
#define Z_STEP_BIT 4
#define X_DIRECTION_BIT 5
#define Y_DIRECTION_BIT 6
#define Z_DIRECTION_BIT 7

#define LIMIT_DDR DDRB
#define LIMIT_PIN PINB
#define X_LIMIT_BIT 1
#define Y_LIMIT_BIT 2
#define Z_LIMIT_BIT 3

#define SPINDLE_ENABLE_DDR DDRB
#define SPINDLE_ENABLE_PORT PORTB
#define SPINDLE_ENABLE_BIT 4

#define SPINDLE_DIRECTION_DDR DDRB
#define SPINDLE_DIRECTION_PORT PORTB
#define SPINDLE_DIRECTION_BIT 5

// This parameter sets the delay time before disabling the steppers after the final block of movement.
// A short delay ensures the steppers come to a complete stop and the residual inertial force in the
// CNC axes don't cause the axes to drift off position. This is particularly important when manually
// entering g-code into grbl, i.e. locating part zero or simple manual machining. If the axes drift,
// grbl has no way to know this has happened, since stepper motors are open-loop control. Depending
// on the machine, this parameter may need to be larger or smaller than the default time.
// NOTE: If defined 0, the delay will not be compiled.
#define STEPPER_IDLE_LOCK_TIME 25 // (milliseconds) - Integer >= 0

// The temporal resolution of the acceleration management subsystem. Higher number give smoother
// acceleration but may impact performance.
// NOTE: Increasing this parameter will help any resolution related issues, especially with machines
// requiring very high accelerations and/or very fast feedrates. In general, this will reduce the
// error between how the planner plans the motions and how the stepper program actually performs them.
// However, at some point, the resolution can be high enough, where the errors related to numerical
// round-off can be great enough to cause problems and/or it's too fast for the Arduino. The correct
// value for this parameter is machine dependent, so it's advised to set this only as high as needed.
// Approximate successful values can range from 30L to 100L or more.
#define ACCELERATION_TICKS_PER_SECOND 50L

// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
// of the buffer and all stops. This should not be much greater than zero and should only be changed
// if unwanted behavior is observed on a user's machine when running at very slow speeds.
#define MINIMUM_PLANNER_SPEED 0.0 // (mm/min)

// Minimum stepper rate. Sets the absolute minimum stepper rate in the stepper program and never runs
// slower than this value, except when sleeping. This parameter overrides the minimum planner speed.
// This is primarily used to guarantee that the end of a movement is always reached and not stop to
// never reach its target. This parameter should always be greater than zero.
#define MINIMUM_STEPS_PER_MINUTE 800 // (steps/min) - Integer value only

// Number of arc generation iterations by small angle approximation before exact arc trajectory
// correction. This parameter maybe decreased if there are issues with the accuracy of the arc
// generations. In general, the default value is more than enough for the intended CNC applications
// of grbl, and should be on the order or greater than the size of the buffer to help with the
// computational efficiency of generating arcs.
#define N_ARC_CORRECTION 25 // Integer (1-255)

#endif

// Pin-assignments from Grbl 0.5

// #define STEPPERS_DISABLE_DDR DDRD
// #define STEPPERS_DISABLE_PORT PORTD
// #define STEPPERS_DISABLE_BIT 2
//
// #define STEPPING_DDR DDRC
// #define STEPPING_PORT PORTC
// #define X_STEP_BIT 0
// #define Y_STEP_BIT 1
// #define Z_STEP_BIT 2
// #define X_DIRECTION_BIT 3
// #define Y_DIRECTION_BIT 4
// #define Z_DIRECTION_BIT 5
//
// #define LIMIT_DDR DDRD
// #define LIMIT_PORT PORTD
// #define X_LIMIT_BIT 3
// #define Y_LIMIT_BIT 4
// #define Z_LIMIT_BIT 5
//
// #define SPINDLE_ENABLE_DDR DDRD
// #define SPINDLE_ENABLE_PORT PORTD
// #define SPINDLE_ENABLE_BIT 6
//
// #define SPINDLE_DIRECTION_DDR DDRD
// #define SPINDLE_DIRECTION_PORT PORTD
// #define SPINDLE_DIRECTION_BIT 7
Something went wrong with that request. Please try again.