Merge pull request #2672 from tinic/master

Add support for STM32U535xx/STM32U545xx

hw/bsp/stm32u5/boards/stm32u545nucleo/board.cmake

@@ -0,0 +1,8 @@
+set(MCU_VARIANT stm32u545xx)
+set(JLINK_DEVICE stm32u545re)
+
+function(update_board TARGET)
+  target_compile_definitions(${TARGET} PUBLIC
+    STM32U545xx
+    )
+endfunction()

hw/bsp/stm32u5/boards/stm32u545nucleo/board.h

@@ -0,0 +1,112 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2023, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+extern "C"
+{
+#endif
+
+// LED GREEN
+#define LED_PORT GPIOA
+#define LED_PIN GPIO_PIN_5
+#define LED_STATE_ON 1
+
+// BUTTON
+#define BUTTON_PORT GPIOC
+#define BUTTON_PIN GPIO_PIN_13
+#define BUTTON_STATE_ACTIVE 1
+
+// UART Enable for STLink VCOM
+#define UART_DEV LPUART1
+#define UART_CLK_EN __HAL_RCC_LPUART1_CLK_ENABLE
+#define UART_GPIO_PORT GPIOA
+#define UART_GPIO_AF GPIO_AF8_LPUART1
+#define UART_TX_PIN GPIO_PIN_2
+#define UART_RX_PIN GPIO_PIN_3
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+
+static void SystemClock_Config(void) {
+  RCC_OscInitTypeDef RCC_OscInitStruct = { 0 };
+  RCC_ClkInitTypeDef RCC_ClkInitStruct = { 0 };
+  RCC_PeriphCLKInitTypeDef PeriphClkInit = { 0 };
+
+  /* Enable Power Clock */
+  __HAL_RCC_PWR_CLK_ENABLE();
+
+  /** Configure the main internal regulator output voltage
+   */
+  HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+  /** Initializes the CPU, AHB and APB buses clocks
+  */
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48 | RCC_OSCILLATORTYPE_HSI;
+  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+  RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;
+  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+  RCC_OscInitStruct.PLL.PLLMBOOST = RCC_PLLMBOOST_DIV1;
+  RCC_OscInitStruct.PLL.PLLM = 1;
+  RCC_OscInitStruct.PLL.PLLN = 10;
+  RCC_OscInitStruct.PLL.PLLP = 2;
+  RCC_OscInitStruct.PLL.PLLQ = 2;
+  RCC_OscInitStruct.PLL.PLLR = 1;
+  RCC_OscInitStruct.PLL.PLLRGE = RCC_PLLVCIRANGE_1;
+  RCC_OscInitStruct.PLL.PLLFRACN = 0;
+  HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+  PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
+  PeriphClkInit.IclkClockSelection = RCC_CLK48CLKSOURCE_HSI48;
+
+  HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
+
+  /** Initializes the CPU, AHB and APB buses clocks
+   */
+  RCC_ClkInitStruct.ClockType =
+      RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_PCLK3;
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+  RCC_ClkInitStruct.APB3CLKDivider = RCC_HCLK_DIV1;
+
+  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4);
+}
+
+static void SystemPower_Config(void) {
+}
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* BOARD_H_ */

hw/bsp/stm32u5/boards/stm32u545nucleo/board.mk

@@ -0,0 +1,11 @@
+CFLAGS += \
+  -DSTM32U545xx \
+
+# All source paths should be relative to the top level.
+LD_FILE = ${FAMILY_PATH}/linker/STM32U545xx_FLASH.ld
+
+SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32u545xx.s
+
+MCU_VARIANT = stm32u545xx
+# For flash-jlink target
+JLINK_DEVICE = stm32u545re

hw/bsp/stm32u5/boards/stm32u575eval/board.mk

@@ -6,5 +6,6 @@ LD_FILE = ${FAMILY_PATH}/linker/STM32U575xx_FLASH.ld
 
 SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32u575xx.s
 
+MCU_VARIANT = stm32u575xx
 # For flash-jlink target
 JLINK_DEVICE = stm32u575ai

hw/bsp/stm32u5/boards/stm32u575nucleo/board.mk

@@ -6,5 +6,6 @@ LD_FILE = ${FAMILY_PATH}/linker/STM32U575xx_FLASH.ld
 
 SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32u575xx.s
 
+MCU_VARIANT = stm32u575xx
 # For flash-jlink target
 JLINK_DEVICE = stm32u575zi

hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.mk

@@ -7,5 +7,6 @@ LD_FILE = ${BOARD_PATH}/STM32U5A5ZJTXQ_FLASH.ld
 
 SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32u5a5xx.s
 
+MCU_VARIANT = stm32u5a5xx
 # For flash-jlink target
 JLINK_DEVICE = stm32u575zi

hw/bsp/stm32u5/family.c

@@ -72,7 +72,9 @@ void board_init(void) {
   __HAL_RCC_GPIOC_CLK_ENABLE();
   __HAL_RCC_GPIOD_CLK_ENABLE();
   __HAL_RCC_GPIOE_CLK_ENABLE();
+#ifdef GPIOF
   __HAL_RCC_GPIOF_CLK_ENABLE();
+#endif
   __HAL_RCC_GPIOG_CLK_ENABLE();
   __HAL_RCC_GPIOH_CLK_ENABLE();
 
@@ -140,6 +142,17 @@ void board_init(void) {
   GPIO_InitStruct.Alternate = GPIO_AF10_USB;
   HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
 
+#ifdef USB_DRD_FS
+  // STM32U535/STM32U545
+
+  /* Enable USB power on Pwrctrl CR2 register */
+  HAL_PWREx_EnableVddUSB();
+
+  /* USB clock enable */
+  __HAL_RCC_USB_FS_CLK_ENABLE();
+
+#endif
+
 #ifdef USB_OTG_FS
   #if CFG_TUSB_OS == OPT_OS_FREERTOS
   // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
@@ -170,7 +183,9 @@ void board_init(void) {
   /* USB clock enable */
   __HAL_RCC_USB_OTG_FS_CLK_ENABLE();
 
-#else
+#endif
+
+#ifdef USB_OTG_HS
   // STM59x/Ax/Fx/Gx only have 1 USB HS port
 
   #if CFG_TUSB_OS == OPT_OS_FREERTOS

hw/bsp/stm32u5/family.cmake

@@ -102,10 +102,16 @@ function(family_configure_example TARGET RTOS)
 
   # Add TinyUSB target and port source
   family_add_tinyusb(${TARGET} OPT_MCU_STM32U5 ${RTOS})
-  target_sources(${TARGET}-tinyusb PUBLIC
-    ${TOP}/src/portable/synopsys/dwc2/dcd_dwc2.c
-    #${TOP}/src/portable/st/typec/typec_stm32.c
-    )
+  if ((${MCU_VARIANT} STREQUAL "stm32u535xx") OR (${MCU_VARIANT} STREQUAL "stm32u545xx"))
+    target_sources(${TARGET}-tinyusb PUBLIC
+      ${TOP}/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c
+      )
+  else ()
+    target_sources(${TARGET}-tinyusb PUBLIC
+      ${TOP}/src/portable/synopsys/dwc2/dcd_dwc2.c
+      #${TOP}/src/portable/st/typec/typec_stm32.c
+      )
+  endif ()
   target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD})
 
   # Link dependencies

hw/bsp/stm32u5/family.mk

@@ -27,18 +27,28 @@ LDFLAGS_GCC += \
   --specs=nosys.specs --specs=nano.specs
 
 SRC_C += \
-	src/portable/synopsys/dwc2/dcd_dwc2.c \
 	$(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \
 	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \
 	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \
 	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c \
-  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_icache.c \
+	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_icache.c \
 	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_pwr.c \
 	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_pwr_ex.c \
 	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \
 	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \
 	$(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_uart.c
 
+ifeq ($(MCU_VARIANT),stm32u545xx)
+SRC_C += \
+	src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c
+else ifeq ($(MCU_VARIANT),stm32u535xx)
+SRC_C += \
+	src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c
+else
+SRC_C += \
+	src/portable/synopsys/dwc2/dcd_dwc2.c
+endif
+
 INC += \
 	$(TOP)/lib/CMSIS_5/CMSIS/Core/Include \
 	$(TOP)/$(ST_CMSIS)/Include \

src/common/tusb_mcu.h

@@ -271,17 +271,24 @@
   #define TUP_DCD_ENDPOINT_MAX    8
 
 #elif TU_CHECK_MCU(OPT_MCU_STM32U5)
-  #define TUP_USBIP_DWC2
-  #define TUP_USBIP_DWC2_STM32
+  #if defined (STM32U535xx) || defined (STM32U545xx)
+    #define TUP_USBIP_FSDEV
+    #define TUP_USBIP_FSDEV_STM32
+    #define TUP_DCD_ENDPOINT_MAX    8
 
-  // U59x/5Ax/5Fx/5Gx are highspeed with built-in HS PHY
-  #if defined(STM32U595xx) || defined(STM32U599xx) || defined(STM32U5A5xx) || defined(STM32U5A9xx) || \
-      defined(STM32U5F7xx) || defined(STM32U5F9xx) || defined(STM32U5G7xx) || defined(STM32U5G9xx)
-    #define TUP_DCD_ENDPOINT_MAX  9
-    #define TUP_RHPORT_HIGHSPEED  1
-    #define TUP_USBIP_DWC2_TEST_MODE
   #else
-    #define TUP_DCD_ENDPOINT_MAX  6
+    #define TUP_USBIP_DWC2
+    #define TUP_USBIP_DWC2_STM32
+
+    // U59x/5Ax/5Fx/5Gx are highspeed with built-in HS PHY
+    #if defined(STM32U595xx) || defined(STM32U599xx) || defined(STM32U5A5xx) || defined(STM32U5A9xx) || \
+        defined(STM32U5F7xx) || defined(STM32U5F9xx) || defined(STM32U5G7xx) || defined(STM32U5G9xx)
+      #define TUP_DCD_ENDPOINT_MAX  9
+      #define TUP_RHPORT_HIGHSPEED  1
+      #define TUP_USBIP_DWC2_TEST_MODE
+    #else
+      #define TUP_DCD_ENDPOINT_MAX  6
+    #endif
   #endif
 
 #elif TU_CHECK_MCU(OPT_MCU_STM32L5)

src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c

@@ -232,7 +232,7 @@ void dcd_init(uint8_t rhport)
   }
   USB->CNTR = 0; // Enable USB
 
-#if !defined(STM32G0) && !defined(STM32H5) // BTABLE register does not exist any more on STM32G0, it is fixed to USB SRAM base address
+#if !defined(STM32G0) && !defined(STM32H5) && !defined(STM32U5) // BTABLE register does not exist any more on STM32G0, it is fixed to USB SRAM base address
   USB->BTABLE = DCD_STM32_BTABLE_BASE;
 #endif
   USB->ISTR = 0; // Clear pending interrupts

src/portable/st/stm32_fsdev/fsdev_stm32.h

@@ -159,6 +159,35 @@
     #define USB_PMAADDR (USB_BASE + (USB_PMAADDR_NS - USB_BASE_NS))
   #endif
 
+#elif CFG_TUSB_MCU == OPT_MCU_STM32U5
+  #include "stm32u5xx.h"
+  #define FSDEV_BUS_32BIT
+
+  #define FSDEV_PMA_SIZE (2048u)
+  #undef USB_PMAADDR
+  #define USB_PMAADDR USB_DRD_PMAADDR
+  #define USB_TypeDef USB_DRD_TypeDef
+  #define EP0R CHEP0R
+  #define USB_EP_CTR_RX USB_EP_VTRX
+  #define USB_EP_CTR_TX USB_EP_VTTX
+  #define USB_EP_T_FIELD USB_CHEP_UTYPE
+  #define USB_EPREG_MASK USB_CHEP_REG_MASK
+  #define USB_EPTX_DTOGMASK USB_CHEP_TX_DTOGMASK
+  #define USB_EPRX_DTOGMASK USB_CHEP_RX_DTOGMASK
+  #define USB_EPTX_DTOG1 USB_CHEP_TX_DTOG1
+  #define USB_EPTX_DTOG2 USB_CHEP_TX_DTOG2
+  #define USB_EPRX_DTOG1 USB_CHEP_RX_DTOG1
+  #define USB_EPRX_DTOG2 USB_CHEP_RX_DTOG2
+  #define USB_EPRX_STAT USB_CH_RX_VALID
+  #define USB_EPKIND_MASK USB_EP_KIND_MASK
+  #define USB USB_DRD_FS
+  #define USB_CNTR_FRES USB_CNTR_USBRST
+  #define USB_CNTR_RESUME USB_CNTR_L2RES
+  #define USB_ISTR_EP_ID USB_ISTR_IDN
+  #define USB_EPADDR_FIELD USB_CHEP_ADDR
+  #define USB_CNTR_LPMODE USB_CNTR_SUSPRDY
+  #define USB_CNTR_FSUSP USB_CNTR_SUSPEN
+
 #else
   #error You are using an untested or unimplemented STM32 variant. Please update the driver.
   // This includes L1x0, L1x1, L1x2, L4x2 and L4x3, G1x1, G1x3, and G1x4
@@ -211,6 +240,8 @@ static const IRQn_Type fsdev_irq[] = {
   #elif CFG_TUSB_MCU == OPT_MCU_STM32WB
     USB_HP_IRQn,
     USB_LP_IRQn,
+  #elif CFG_TUSB_MCU == OPT_MCU_STM32U5
+    USB_IRQn,
   #else
     #error Unknown arch in USB driver
   #endif