trivial: fix typo milisecond/millisecond for documentation and source…

… comments.

Signed-off-by: Martin Olsson <martin@minimum.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Documentation/CodingStyle

@@ -698,8 +698,8 @@ very often is not. Abundant use of the inline keyword leads to a much bigger
 kernel, which in turn slows the system as a whole down, due to a bigger
 icache footprint for the CPU and simply because there is less memory
 available for the pagecache. Just think about it; a pagecache miss causes a
-disk seek, which easily takes 5 miliseconds. There are a LOT of cpu cycles
-that can go into these 5 miliseconds.
+disk seek, which easily takes 5 milliseconds. There are a LOT of cpu cycles
+that can go into these 5 milliseconds.
 
 A reasonable rule of thumb is to not put inline at functions that have more
 than 3 lines of code in them. An exception to this rule are the cases where

drivers/ide/ide-atapi.c

@@ -577,7 +577,7 @@ static ide_startstop_t ide_transfer_pc(ide_drive_t *drive)
 
 		/*
 		 * If necessary schedule the packet transfer to occur 'timeout'
-		 * miliseconds later in ide_delayed_transfer_pc() after the
+		 * milliseconds later in ide_delayed_transfer_pc() after the
 		 * device says it's ready for a packet.
 		 */
 		if (drive->atapi_flags & IDE_AFLAG_ZIP_DRIVE) {

drivers/isdn/mISDN/dsp_core.c

@@ -502,7 +502,7 @@ dsp_control_req(struct dsp *dsp, struct mISDNhead *hh, struct sk_buff *skb)
 			break;
 		}
 		dsp->cmx_delay = (*((int *)data)) << 3;
-			/* miliseconds to samples */
+			/* milliseconds to samples */
 		if (dsp->cmx_delay >= (CMX_BUFF_HALF>>1))
 			/* clip to half of maximum usable buffer
 			(half of half buffer) */

drivers/net/ipg.h

@@ -514,7 +514,7 @@ enum ipg_regs {
 #define		IPG_DMALIST_ALIGN_PAD	0x07
 #define		IPG_MULTICAST_HASHTABLE_SIZE	0x40
 
-/* Number of miliseconds to wait after issuing a software reset.
+/* Number of milliseconds to wait after issuing a software reset.
  * 0x05 <= IPG_AC_RESETWAIT to account for proper 10Mbps operation.
  */
 #define         IPG_AC_RESETWAIT             0x05

drivers/s390/scsi/zfcp_fc.c

@@ -116,7 +116,7 @@ static void zfcp_wka_port_put(struct zfcp_wka_port *wka_port)
 {
 	if (atomic_dec_return(&wka_port->refcount) != 0)
 		return;
-	/* wait 10 miliseconds, other reqs might pop in */
+	/* wait 10 milliseconds, other reqs might pop in */
 	schedule_delayed_work(&wka_port->work, HZ / 100);
 }
 

drivers/scsi/dpt/osd_util.h

@@ -342,7 +342,7 @@ uLONG osdGetThreadID(void);
 /* wakes up the specifed thread */
 void osdWakeThread(uLONG);
 
-/* osd sleep for x miliseconds */
+/* osd sleep for x milliseconds */
 void osdSleep(uLONG);
 
 #define DPT_THREAD_PRIORITY_LOWEST 0x00

drivers/usb/serial/io_ti.c

@@ -102,7 +102,7 @@ struct edgeport_port {
 	__u8 shadow_mcr;
 	__u8 shadow_lsr;
 	__u8 lsr_mask;
-	__u32 ump_read_timeout;		/* Number of miliseconds the UMP will
+	__u32 ump_read_timeout;		/* Number of milliseconds the UMP will
 					   wait without data before completing
 					   a read short */
 	int baud_rate;

sound/pci/vx222/vx222_ops.c

@@ -367,7 +367,7 @@ static int vx2_load_xilinx_binary(struct vx_core *chip, const struct firmware *x
 	unsigned int port;
 	const unsigned char *image;
 
-	/* XILINX reset (wait at least 1 milisecond between reset on and off). */
+	/* XILINX reset (wait at least 1 millisecond between reset on and off). */
 	vx_outl(chip, CNTRL, VX_CNTRL_REGISTER_VALUE | VX_XILINX_RESET_MASK);
 	vx_inl(chip, CNTRL);
 	msleep(10);