This project is centered around getting a Raspberry Pi setup on a simple home network in order to block ads and naughty DNS requests, secure the DNS requests of all devices on the network, and provide a VPN solution for when any of these devices are outside of the network and would like to take advantage of the security (and speed) benefits of the network remotely.
There are several guides written about this or similar setups, but in praactice there was always something missing or assumptions were made about certain steps in the process. This guide is meant to shed some light on those steps, simplify the process of getting setup, and explain my findings in order to help anyone else trying to do the same.
This is what worked for me, your miles may vary.
While I won't have time to troubleshoot other setups, I'm sharing what I had to work with here. You'll need:
- Raspberry Pi 3 Model B Plus Rev 1.3
- Raspbian 10 Buster Lite
- 16GB MicroSD card (4GB might be enough, but I'd stick with at least 8GB)
- Mac running macOS Mojave (for prepping, backing up, and restoring the SD card)
- USB SD card reader (I use this simple Anker 2-in-1 card reader)
- Mouse and keyboard for intial Raspberry Pi setup (I used a Bluetooth mouse that has its own USB transmitter, and my wife's Apple Magic Keyboard connected via a USB to Lightning cable)
- HDMI cable and montior for initial Raspberry Pi setup (I hooked mine to a TV)
- Apple Time Capsule router (connected directly to a cable modem, acting as a DHCP server)
That said, this process should work on any Raspberry Pi 2 v1.2 and above, and there are Windows/Linux tools to handle the SD card management.
There are many operating systems available to run on the Raspberry Pi, but we'll be using the latest version of Raspbian for this tutorial. There are also several different ways to install Rasbian on your Raspberry Pi, including N00Bs (New Out Of the Box Software). It's an easy operating system installer that allows you to erase your Raspberry Pi's SD card and start from scratch quickly, which is great when you're experimenting with your new device.
You can download N00BS for free in either the normal version (includes Raspbian and LibreELEC installation files) or the lite version (nothing is pre-loaded, you'll download installation files from the internet). Once downloaded, follow the simple instructions to get an SD card ready for your Raspberry Pi.
Once the SD card is ready, insert it into your Raspberry Pi and boot it up. You'll be taken to the N00BS installer screen where you can choose to install any one of several operating systems, including Raspbian. You can choose from Lite (console only), Desktop (includes a GUI), or Full (Desktop and recommended applications).
For the purposes of this setup, we'll install Raspbian Lite (console only). If you ever want to add the desktop GUI, you can always add that later.
Installation generally takes about 10 minutes, but depends on whether you chose Lite or the normal N00BS files and how fast your internet connection is. Once installed, your Raspberry Pi will reboot into the console of a fresh install of Raspbian.
To login to your freshly baked Raspberry Pi, use the default username/password pair of pi and raspberry (yes, very original). The first thing you should do is change your password:
passwd
Enter your current password (raspberry) and then type and retype a new password.
If you'd rather not stick with the default username of pi, changing your Raspbian username is unfortunately not as easy as you'd think. Because you're currently logged in as pi and you can't change the username of the current user, you have to get creative with how you go about this. You could create a new user, logout of the pi user, login as the new user, and then as root you can change the username of pi and its home directory. But now you have a second user.
You can also follow along with these instructions on adding a temporary user and using it to change pi's username, but I can't vouch for this method as I skipped it altogether.
We should enable SSH on the Raspberry Pi so that we can SSH into it from any device on the network, thus no longer needing the mouse, keyboard, HDMI cable, and screen. You'll need to know the IP address of your Raspberry Pi to continue.
First we need the IP address and MAC address of the Raspberry Pi. It's highly recommeneded that you setup a static IP address on your network for your Raspberry Pi so that you can easily SSH into it, and later, point other services directly to it.
To get the current IP address of your Raspberry Pi, run:
ifconfig
And you'll see some output that should include both eth0 details and wlan0 details. The former is your ethernet (wired) network interface, while the latter is your wireless (wifi) network interface. Depending on how you'll be connecting your Raspberry Pi to your network, you'll need to focus on one or the other.
If your Raspberry Pi is wired into your network via an ethernet cable, take a look at the eth0 interface and find the following line:
inet 192.168.x.x netmask 255.255.255.0 broadcast 192.168.x.255
Where 192.168.x.x is the IP address of the Raspberry Pi (I've obfuscated this for privacy reasons). The Raspberry Pi's MAC address is just below that on the line:
ether ab:cd:ef:12:34:gh txqueuelen 1000 (Ethernet)
Where ab:cd:ef:12:34:gh would be the unique MAC address of the eth0 interface on this Raspberry Pi. In order to force your network's router to give the Raspberry Pi a static IP address (the same IP every time it connects), you'll need to edit the settings of your router and add a DHCP Reservation:
Description: Raspberry Pi
Reserve Address By: MAC Address
MAC Address: ab:cd:ef:12:34:gh
IPv4 Address: 192.168.x.x
Once you've created a static IP address of your choosing (matching your router's existing subnet schema), save your changes and restart your router.
Now we'll open the Raspberry Pi's Configuration Tool:
sudo raspi-config
Under the Interfacing Options group, go to SSH and enable it.
You should be prompted to restart your Raspberry Pi. If you aren't, exit the Configuration Tool and type:
sudo reboot
Now that you've enabled SSH on the Raspberry Pi and given it a static IP address, you should be able to do all of the following setup from another device by connecting via SSH. I'll be using a Mac in the following steps.
Open the macOS Terminal application and type:
ssh pi@192.168.x.x
Where pi is the username on your Raspberry Pi and 192.168.x.x is the static IP address you just setup. Then type the new password you set for the pi user to login. You should now be greeted with the Raspian console.
Note: If you get an error that says the host identification has changed, you’ll need to remove the old entry (the one with the same static IP address) from your ~/.ssh/known_hosts file first, then try again.
It's possible to configure the Raspberry Pi to allow a computer to access it without providing a password each time you try to connect. In your Mac's Terminal app, generate SSH key pairs with:
ssh-keygen -t rsa -b 4096
and enter a password for the SSH key (store this somewhere secure, you may need it at a later time). If you already have SSH key(s), give this pair a different name (such as id_rsa_pi). Now that the public and private keys have been generated on your Mac, you'll need to copy the public key to your Raspberry Pi using:
ssh-copy-id pi@192.168.x.x
where pi is the username you use on the Raspberry Pi and the 192.168.x.x is the static IP address of the Raspberry Pi. You'll need to enter the password for the pi user to confirm the copy.
Using an SSH agent, you can store your SSH key(s) in your Mac's Keychain for easy (and secure) access. Add your newly created SSH key pair to the macOS Keychain with:
ssh-add -K ~/.ssh/id_rsa_pi
where id_rsa_pi is the name you used to create the SSH key pair. Enter your macOS password to confirm. In order to prevent macOS from forgetting your SSH keys on restart, you can add it to your ~/.ssh/config file based on these instructions. Your ~/.ssh/config file should look something like this:
Host *
UseKeychain yes
AddKeysToAgent yes
IdentityFile ~/.ssh/id_rsa
IdentityFile ~/.ssh/id_rsa_pi
Now once again, SSH into your Raspberry Pi using the Terminal application by typing ssh pi@192.168.x.x where 192.168.x.x is the static IP address of your Raspberry Pi, and you shouldn’t have to enter a password again from this device! Repeat these steps on other devices to generate and share their SSH key(s) with the Raspberry Pi.
Here are some additional steps I prefer to take upon setting up my Raspberry Pi. First, open the Configuration Tool via your SSH session:
sudo raspi-config
- Under Network Options, change the Hostname to something other than
raspberrypi(most of the devices on my network are named after Transformers). - Under Localisation Options, add to the Locale
en-us UTF8and select it as the default locale (do not remove the defaulten-gb UTF8as it seems to cause issues) - Under Localisation Options, change the timezone to match yours
Once you've got everything up and running, you'll want to update all the Raspbian packages and upgrade any that need it using APT (Advanced Packaging Tool) by running:
sudo apt update
to update packages and then:
sudo apt-get upgrade -y
to upgrade any packages you have installed to their latest versions. This may take a while, so you may want to go grab a coffee, beer, tea...
Note: If at any point during an apt update your package cache file is corrupted, remove your apt lists and refresh them using:
sudo rm -r /var/lib/apt/lists/
sudo mkdir -p /var/lib/apt/lists/partial
sudo apt-get update
Throughout the process of setting things up, you may want to have a backup of your Raspberry Pi so you don’t have to start from scratch if you make a mistake like I have (several times). You may even want to clone your Raspberry Pi after each successful step so you can return to it if the next step goes wrong. For instance, I was sure to create a backup of my Raspberry Pi after initial setup, after I had Pi-Hole working, after I added Unbound, and after I got WireGuard setup. That way if I made any changes that broke my setup, I could always revert the previous working installation.
There are many ways to do this, but if you're on a Mac there is a very simple (and free) solution. You'll want to download the ApplePi-Baker app for macOS, which handles backing up your Raspberry Pi's SD card and can restore from several different formats as well.
At any point you want to backup your Raspberry Pi's configuration, first shutdown the device with:
sudo halt
or the more verbose:
sudo shutdown -h now
and then unplug your Rasbperry Pi (or get a Pi Switch to make life easier). Remove the SD card from the Raspberry Pi and insert into a supported SD card reader (like the Anker 2-in-1 card reader I mentioned earlier), and connect to your Mac.
When you open the ApplePi-Baker app, you should be able to select the SD card from the Select a Disk options (make sure you select the right disk), then choose the Backup option. In the file choose window, select IMG from the Format selections at the bottom of the window, and then give the backup file a name. This should take some time, be prepared to wait.
Note: The IMG format allows ApplePi-Baker to shrink the Linux partition on backup and expand it on restore, saving you from having to backup the entire size of the SD card rather than just the actual contents.
Another way to backup your SD card on a Mac is to open Terminal and type:
diskutil list
to see a list of drives attached to your Mac. To create a Disk Image of the SD card:
sudo dd if=/dev/rdisk2 of=~/RaspberryPiBackup.dmg
where /dev/rdisk2 is the path to your SD card’s disk (with an added r) and ~/RaspberryPiBackup.dmg is the path and filename on your Mac to save the Disk Image. Enter your Mac user’s password when prompted. This may take a while depending on the size of your SD card and what you have installed on it.
Note: If you see any input/output errors, try using Disk Utility instead.
Open the macOS Disk Utility application, and choose View > Show All Devices. Right click on the device name of the SD card (not the individual partition(s)!) and choose the Image from ‘DEVICE NAME’ option. Give the file a name and choose a location to save it. Choose the DVD/CD master option for Format, and no Encryption. Disk Utility will create a .CDR file with your SD card’s files.
Note: Both the Disk Utility and Terminal methods failed for me, both creating input/output errors. Maybe it was my SD card, or my card reader, but then using ApplePi-Baker gave me no issues, so I didn't bother to investigate further.
If you’ve made a backup of your Raspberry Pi’s SD card previously, you can restore it any time and overrite your current configuration. Using the ApplePi-Baker app on macOS, this is a simple task.
First, shutdown your Raspberry Pi:
sudo halt
and remove the SD card from your Raspberry Pi. Using a supported SD card reader, insert the SD card from your Raspberry Pi into your Mac. Launch the ApplePi-Baker app and select the correct SD card disk, then choose the Restore option. ApplePi-Baker will expand the backup file and overrite the complete contents of your SD card with the backup file's contents, so make sure you really want to do this.
You can also use the macOS Terminal application to this by typing:
diskutil list
to see a list of drives attached to your Mac. You'll need to unmount the SD card to proceed (your Mac can still see the files, but you won't see the mounted disk(s) anymore):
diskutil unmountDisk /dev/disk2
where /dev/disk2 is the path to your SD card’s disk. Restore the SD card from backup using:
sudo dd if=~/RaspberryPiBackup.dmg of=/dev/disk2
where /dev/disk2 is the path to your SD card’s disk and ~/RaspberryPiBackup.dmg is the path and filename on your Mac to save the Disk Image. This may take a while depending on the size of your SD card backup
Note: If you backed up the SD card as a .CDR, you can rename it to .ISO and restore it to any SD card with the free Etcher application for macOS.
Pi-Hole provides ad-blocking at the network level, meaning you not only stop ads from making it to any of the devices on your network, but you also block the unnecessary network requests for those ads and thus reduce bandwidth usage. Pi-Hole pairs nicely with a VPN (Virtual Private Network) so that you can connect remotely and still take advantage of ad-blocking from anywhere outside your network.
First you'll need to run the Pi-Hole installer:
sudo curl -sSL https://install.pi-hole.net | bash
Note: If you see the error “Script called with non-root privileges” during setup, you can download the install script and run it as root instead. Do this by downloading the script:
wget -O basic-install.sh https://install.pi-hole.net
and then run the installer as root:
sudo bash basic-install.sh
During setup, select OK for the first few screens, then select either eth0 for ethernet (wired) or wlan0 for wireless (wifi) on the Choose An Interface screen. Next, select any Upstream DNS Provider since we’ll be using our own Unbound server later. Choose any Block Lists you want to use, or leave them all checked by default. Choose both IPv4 and IPv6 on the Select Protocols screen. Use the current network settings on the next screen, assuming you gave your Raspberry Pi a static IP address earlier. Then decide if you want to install the Web Interface for Pi-Hole (and lighthttpd to serve it), which you'll typically want to keep an eye on your traffic and blocked queries (and to make additional configuration changes) in a web browser.
Lastly, decide how you want to log queries and what privacy mode do you want for FTL (Faster Than Light). Setup will finish, and the Pi-Hole DNS service will be running.
After Pi-Hole setup is complete, you should see the default Web Interface password on the console. You can change the password using:
pihole -a -p
Now you can access the Pi-Hole Web Interface in your browser by going to http://192.168.x.x/admin where 192.168.x.x is the static IP of your Raspberry Pi (you can also use http://pi.hole/admin once you point your router to use Pi-Hole as your DNS service in the next step). Go to Login, then enter the new password you set for the Web Interface and check the “Remember me for 7 days” checkbox before logging in. You won’t see much on the Dashboard yet since nothing on your network is using Pi-Hole, but that should change momentarily.
To make sure Pi-Hole is working, you can set a single device to use it as its DNS service or you can point your network’s router to it instead to force (almost) every device on your network to use Pi-Hole as its DNS service. Most routers have a setting for Primary and Secondary DNS, and you'll want to point the Primary DNS Server to the static IP address of your Raspberry Pi (192.168.x.x) and the Secondary DNS Server to a 3rd party DNS service like Google (8.8.8.8) or Cloudflare (1.1.1.1) in case your Pi-Hole server goes down for some reason and you don’t want to lose all connectivity to the outside world (like when you're fiddling around with your Raspberry Pi in the upcoming steps).
Restart your router and watch as the Pi-Hole Dashboard (now available on your internal network at http://pi.hole/admin) fills up with blocked queries!
Note: If at any point your Raspberry Pi loses its connection with the outside world and you want to set a temporary DNS server to resolve it, run:
echo "nameserver 8.8.8.8" | sudo tee /etc/resolv.conf > /dev/null
to temporarily set the device's DNS server to Google until you can figure out what you did. This will reset on reboot.
Unbound is a validating, recursive, caching DNS resolver. It is designed to be fast and lean and incorporates modern features based on open standards.
Setting up Unbound DNS with your Pi-Hole installation allows us to operate our own tiny, recursive DNS server instead of relying on (and sending data to) the big players like Google or Cloudflare.
To install Unbound on the Raspberry Pi:
sudo apt install unbound
Afterwards we'll need to download a root.hints file to replace the built-in hints:
wget -O root.hints https://www.internic.net/domain/named.root
Move the root.hints file to the Unbound configuration directory:
sudo mv root.hints /var/lib/unbound/
Unbound includes a lot of different configuration options that you can adjust and try out. Feel free to scan the Unbound configuration file documentation for details about each option.
To get started, edit the Pi-Hole configuration file:
sudo nano /etc/unbound/unbound.conf.d/pi-hole.conf
and remove anything already in the file before copying and pasting the contents of the sample pi-hole.conf configuration file in this repository. When you're done, exit and save the file.
Some things to note:
port: 5353
The default port for Unbound is 53 but we're changing it to 5353 here. Feel free to change it to whatever you like, but you'll need to remember it later when we tell Pi-Hole where to send upstream DNS requests.
# Use this only when you downloaded the list of primary root servers!
root-hints: "/var/lib/unbound/root.hints"
This points to the root.hints file you just downloaded.
# IPs authorized to access the DNS Server
access-control: 0.0.0.0/0 refuse
access-control: 127.0.0.1 allow
access-control: 192.168.x.0/24 allow
Here we're refusing connections to all interfaces and then we're allowing anything from this device (your Raspberry Pi) and anything from our local subnet (be sure to change 192.168.x.0 to whatever your local subnet is).
# Time To Live (in seconds) for DNS cache. Set cache-min-ttl to 0 remove caching (default).
# Max cache default is 86400 (1 day).
cache-min-ttl: 3600
cache-max-ttl: 86400
You can adjust the cache settings if you like. Instead of the default of not caching, here we set the minimum TTL (Time To Live) to 1 hour, afterwards the DNS will do another lookup of the cached data.
# Create DNS record for Pi-Hole Web Interface
private-domain: "pi.hole"
local-zone: "pi.hole" static
local-data: "pi.hole IN A 192.168.x.x"
When Pi-Hole was doing DNS, it created this custom record for http://pi.hole so we could easily reach the Web Interface without typing in the static IP address of the Raspberry Pi. Now that Unbound is our DNS, we'll need to create this custom record in the Unbound configuration file. Be sure to replace 192.168.x.x with the static IP address of your Raspberry Pi.
Once the configuration file is saved, start the Unbound DNS server:
sudo service unbound start
And test to make sure the Unbound DNS is running:
dig pi-hole.net @127.0.0.1 -p 5353
If you run this command, it should return a status of SERVFAIL:
dig sigfail.verteiltesysteme.net @127.0.0.1 -p 5353
And this command should return a status of NOERROR:
dig sigok.verteiltesysteme.net @127.0.0.1 -p 5353
Now that your Unbound recursive DNS resolver is running locally, we'll force Pi-Hole to use it for DNS rather than an outside source like Google (8.8.8.8) or Cloudflare (1.1.1.1) and keep all of our network traffic contained. Any traffic on your network will be sent to Pi-Hole, which in turn will use Unbound for DNS resolution before blocking the appropriate domains and returning data.
First, open the Pi-Hole Web Interface in a web browser on your local network: http://pi.hole/admin
Then go to Settings > DNS and uncheck any third party Upstream DNS Servers you had selected during setup. To the Custom 1 (IPv4) Upstream DNS Servers input, add:
127.0.0.1#5353
Where 127.0.0.1 points the Pi-Hole server (the Raspberry Pi) to itself on port 5353. If you changed the port in your Unbound configuration file, use that port here instead.
Next, uncheck Never forward non-FQDNs and Never forward reverse lookups for private IP ranges and check Use Conditional Forwarding and enter your router’s IP address (typically something like x.x.x.1 on your subnet), along with the Domain Name (this can be set on your router, usually under the DHCP settings, to something like home).
Lastly, do not check Use DNSSEC as Pi-Hole is going to be using your Unbound DNS, which already enables DNSSEC (Domain Name System Security Extensions).
When you're done, don't forget to save your settings. To check and make sure DNSSEC is working, visit this URL in your browser within your network: http://dnssec.vs.uni-due.de
WireGuard is an extremely simple yet fast and modern VPN that utilizes state-of-the-art cryptography. It aims to be faster, simpler, leaner, and more useful than IPsec, while avoiding the massive headache. It intends to be considerably more performant than OpenVPN.
First, install the necessary packages before WireGuard setup begins:
sudo apt install raspberrypi-kernel-headers libelf-dev libmnl-dev build-essential git
Switch to root with sudo su and enter the next 2 commands per the Debian installation commands (check to see if these have changed, and use the official Debian instructions if they have):
echo "deb http://deb.debian.org/debian/ unstable main" > /etc/apt/sources.list.d/unstable.list
printf 'Package: *\nPin: release a=unstable\nPin-Priority: 90\n' > /etc/apt/preferences.d/limit-unstable
Then exit root.
Run an APT update and ignore the error:
sudo apt update
Then install dirmngr for handling certificates:
sudo apt install dirmngr
You'll need to connect with the keyserver with both of these keys, though I'm not exactly sure why...
sudo apt-key adv --keyserver keyserver.ubuntu.com --recv-keys 7638D0442B90D010
sudo apt-key adv --keyserver keyserver.ubuntu.com --recv-keys 04EE7237B7D453EC
Run another APT update:
sudo apt update
and then install WireGuard:
sudo apt install wireguard
Next we'll enable IP forwarding:
sudo perl -pi -e 's/#{1,}?net.ipv4.ip_forward ?= ?(0|1)/net.ipv4.ip_forward = 1/g' /etc/sysctl.conf
Finally, reboot your Raspberry Pi:
sudo reboot
After reboot, verify that IP forwarding is enabled by running:
sysctl net.ipv4.ip_forward
You should see net.ipv4.ip_forward = 1 as a result, otherwise add the above command to your /etc/sysctl.conf file.
In the next steps, we'll need to create private and public keys for both the WireGuard server as well as a VPN client. Once everything is setup, we can create additional keys for other clients to use the VPN as well.
I've found it easiset to first become root before running the commands below:
sudo su
Then switch to the directory where we'll store the WireGuard keys:
cd /etc/wireguard
If this directory doesn't exist, just run mkdir /etc/wireguard and then cd /etc/wireguard. Set permissions on the entire directory with the umask command so that only the root user can read or write data here:
umask 077
Next, generate the server’s private & public keys in a single command:
wg genkey | tee server_privatekey | wg pubkey > server_publickey
Then generate a client’s private & public keys:
wg genkey | tee peer1_privatekey | wg pubkey > peer1_publickey
To confirm the keys were generated and permissioned:
ls -la
Finally, output your new WireGuard keys to the console and save them (possibly in a text file, just be sure to delete it when we're done) for the next steps:
cat server_privatekey
cat server_publickey
cat peer1_privatekey
cat peer1_publickey
Lastly, exit root before continuing.
Create and edit the WireGuard configuration file:
sudo nano /etc/wireguard/wg0.conf
and replace the contents with the WireGuard wg0.conf from this repository.
You'll need to make the following changes:
[Interface]
Address = 10.9.0.1/24
This is the WireGuard interface, which will create a virtual subnet of 10.9.0.0 and assign itself an internal IP address of 10.9.0.1. You can change this if you'd like, but you'll also need to change the internal IP of VPN clients as well.
# Default WireGuard port, change to anything that doesn’t conflict
ListenPort = 51820
The default port for WireGuard, which you can change if you'd like. You'll also need to open up this port on your router, otherwise incoming VPN traffic from outside your network will not make it to WireGuard. Information on how to do this is later in the guide.
Note: Some public wifi networks will block all ports other than 80 (TCP), 443 (TCP), and 53 (UDP) for HTTP, HTTPS, and DNS respectively. If you are connected to a public wifi network that does this, you will not be able to connect to your WireGuard VPN. One way around this is to set your WireGuard ListenPort to 53 and create a forward on your network's router on port 53, thus circumventing the issue with blocked ports. Do this at your own risk, and definitely do not enable Pi-Hole's Listen on all interfaces, permit all origins DNS option if you are forwarding port 53 on your router.
DNS = 192.168.x.x
Replace 192.168.x.x with the static IP address of your Raspberry Pi.
PrivateKey = <server_privatekey>
Replace <server_privatekey> with the output of your cat server_privatekey command earlier.
PostUp = iptables -A FORWARD -i %i -j ACCEPT; iptables -A FORWARD -o %i -j ACCEPT; iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
PostDown = iptables -D FORWARD -i %i -j ACCEPT; iptables -D FORWARD -o %i -j ACCEPT; iptables -t nat -D POSTROUTING -o eth0 -j MASQUERADE
We're using eth0 here when the Raspberry Pi is connected over ethernet (wired), but you can replace both instances with wlan0 if your Raspberry Pi is connected via wifi (wireless).
The next section of the WireGuard configuration file is for clients that connect to the VPN. For each client (device), you'll need to add another [Peer] section here and also create a separate client configuration file (details for that are next).
[Peer]
# Peer 1
PublicKey = <peer1_publickey>
Replace <peer1_publickey> with the output of your cat peer1_publickey command earlier.
AllowedIPs = 10.9.0.2/32
Using the virtual subnet created by WireGuard, give this device an internal IP address of 10.9.0.2.
Once your WireGuard configuration file is compelete, exit the nano editor and save your changes.
Now that WireGuard is configured, we'll need to create a client configuration file for each VPN client we want to connect to the network. First, create and edit your first client configuration file:
sudo nano /etc/wireguard/peer1.conf
and replace the contents with the WireGuard client peer1.conf from this repository. You'll need to make the following changes:
[Interface]
Address = 10.9.0.2/32
Use the same virtual IP address that you used in the wg0.conf file earlier for this client.
DNS = 192.168.x.x
Replace 192.168.x.x with the static IP address of your Raspberry Pi.
PrivateKey = <peer1_privatekey>
Replace <peer1_privatekey> with the output of your cat peer1_privatekey command earlier.
[Peer]
PublicKey = <server_publickey>
Replace <server_publickey> with the output of your cat server_publickey command earlier.
Endpoint = YOUR-PUBLIC-IP/DDNS:ListenPort
The Endpoint here refers to the public IP address and port number for incoming traffic to your network's router from the outside world. This is necessary so that devices outside your network know where to go to connect to your internal network's VPN. Your public IP address is available by visiting IP Leak, and the ListenPort should be set to the same port you set in your WireGuard's wg0.conf file (the default port is 51820).
# For full tunnel use 0.0.0.0/0, ::/0 and for split tunnel use 192.168.1.0/24
# or whatever your router’s subnet is
AllowedIPs = 0.0.0.0/0, ::/0
For this use case, we're using a full tunnel rather than a split tunnel (which allows some network traffic to come through outside of the VPN).
If your ISP does not provide you with a static IP address (most don’t), and your IP changes for some reason (cable modem reboot, connectivity issues, etc.), your home network may be unreachable from the outside until you update it in your configuration files. The solution is to use a DDNS (Dynamic DNS) service where you choose a readable domain name and can automatically notify the service when your public IP address changes.
So instead of worry about whether your public IP address is 98.10.200.11 or 98.10.200.42, you can instead point a domain name like username.us.to at your public IP address and have the DDNS service update the domain record when your public IP address changes.
There are plenty of DDNS services out there, but I’m using Afraid.org’s Free DNS service because it doesn’t nag you to login every 30 days, even on the completely free plan.
First, create a Free DNS account at: http://freedns.afraid.org
After account creation, verify your account using the link you’ll receive in your email. Then go to Add Subdomain and enter a Subdomain (a username, your name, company name, etc.) and choose a Domain (there are many to choose from besides what’s listed, follow the instructions to find the rest). Leave Type set to an A record, TTL is set to 3600 for free accounts, and Wildcard functionality is only for paid accounts.
Your public IP address should be automatically filled in, but you can visit IP Leak in a browser to get your public IP address if you need to.
Enter the CAPTCHA text and hit Save to continue. You should now have a shiny new subdomain pointing to your network’s public IP address! But what if your public IP address changes at some point?
Having a domain name pointed to your public IP address is useless if that IP address changes in the future, which is why DDNS services exist in the first place. We'll need to update our Free DNS record if our network's public IP address changes, which is fairly simple to do.
While logged in at Free DNS, go to the Dynamic DNS page and look for your new subdomain record. Right click the Direct URL link associated with your subdomain record and choose Copy Link. We'll use this to update your subdomain record directly from the Raspberry Pi.
On the Raspberry Pi, create a cronjob that runs every 5 minutes (replacing the XXXXX with the unique identifier in your Direct URL):
crontab -l | { cat; echo "*/5 * * * * curl http://freedns.afraid.org/dynamic/update.php?XXXXX”; } | crontab -
You’ll see no crontab for ... on the console, you can safely ignore that. You can change the timing from 5 minutes to 20 minutes (or whatever you'd like) by adjusting the */5 * * * * part to */20 * * * *. Verify that you’ve added the command correctly with:
crontab -l
Once you've finished, restart the cron service with:
sudo service cron restart
Now your DDNS subdomain will always point to the correct public IP address of your network, and VPN clients will be able to reach your network remotely regardless of whether your public IP address changes.
Go back to your WireGuard client configuration file and use your new DDNS subdomain with the ListenPort you set earlier and never worry about your public IP address changing! In the /etc/wireguard/peer1.conf file, edit the Endpoint:
Endpoint = username.us.to:51820
using the subdomain you chose on Free DNS and the ListenPort you set in your /etc/wireguard/wg0.conf file.
Unlike IPSec or IKEv2, WireGuard isn’t built into the Android or iOS operating system (yet), so you’ll have to download the WireGuard app to each device to connect to your VPN. Here are some of the VPN clients available:
Android: https://play.google.com/store/apps/details?id=com.wireguard.android&hl=en_US
iOS: https://apps.apple.com/us/app/wireguard/id1441195209
macOS: https://apps.apple.com/us/app/wireguard/id1451685025?mt=12
Rather than manually enter all the WireGuard configuration details into your phone, we can create a QR code directly on the Raspberry Pi console that your phone's native WireGuard app can scan and automatically fill out the details for you.
First, install the QR encoder on the Raspberry Pi:
sudo apt install qrencode
Become the root user in order to read the WireGuard client config:
sudo su
Create a QR code from the VPN client configuration we set up earlier:
qrencode -t ansiutf8 < /etc/wireguard/peer1.conf
Note: You may have to adjust the size of your Terminal/console window to properly show the QR code generated
Open the WireGuard app on your phone, tap Add a tunnel and select the Create from QR code option. Scan the QR code with your phone’s camera, give the tunnel a name, and allow WireGuard to add VPN configurations to your phone's operating system.
Now you can enable or disable VPN access directly through the WireGuard app!
On your Raspberry Pi, there are a few more steps needed to complete setup of the WireGuard VPN. First, allow WireGuard to start on boot:
sudo systemctl enable wg-quick@wg0
Set the correct permissions on the WireGuard configuration file with:
sudo chown -R root:root /etc/wireguard/
sudo chmod -R og-rwx /etc/wireguard/
On your Pi-Hole Web Interface, go to Settings > DNS and choose the Listen on all interfaces, permit all origins option under Interface listening behavior, then save your settings.
Start WireGuard now with:
sudo wg-quick up wg0
To check and see if the WireGuard interface was created successfully:
ifconfig wg0
Restart your Raspberry Pi with:
sudo reboot
Once the Raspberry Pi is done booting, check if WireGuard working:
sudo wg
You should see interface wg0 and a peer.
Without this step, you will not be able to reach your VPN from outside of the network. None of the write-ups I found mentioned this step, most likely assuming you would already know to do this (I didn't).
In order to reach your VPN from outside your network, you'll have to setup a UDP-specific port forward on your network's router that passes traffic on that port to an internal IP address of your choosing. Generally speaking, this might look like:
Description: WireGuard VPN
Public UDP Ports: 51820
Private IP Address: 192.168.x.x
Private UDP Ports: 51820
Where 192.168.x.x is the internal static IP address of the Raspberry Pi running WireGuard, and 51820 is whatever you set the ListenPort to in your /etc/wireguard/wg0.conf file. Each router has different settings available, but the above are from my Apple Time Capsule's AirPort Utility in macOS.
Note: I'm passing just UDP traffic on this port, as WireGuard uses UDP and not TCP.
Once you've added this port forwarding on your network's router, restart the device and now you should be able to connect to your WireGuard VPN from outside your network and enjoy the benefits of network-level ad-blocking from anywhere, at any time!
When connected to your VPN from outside the network, you can check to see if there are any leaks in your DNS lookups using the DNS Leak Test service.
There are several write-ups out there on how to do this, as well as install scripts to do it for you. Since the Raspberry Pi was meant to be a learning tool, I used this opportunity to figure things out on my own with the help of documentation from both software creators and the community. If it weren't for the latter, I doubt I would've been able to do this on my own. Thanks to everyone who has taken the time to share their knowledge, and experience, in setting up a Raspberry Pi.
Build Your Own WireGuard VPN Server with Pi-Hole for DNS Level Ad Blocking
Seth Enoka's write-up includes some additional firewall setup with IPtables, which I skipped. But this is an excellent reference for what we're doing, even though he uses a VPS with Ubuntu rather than a Raspberry Pi.
Raspbian GNU/Linux 10 (buster) Lite
Harry Nyce posted his Pi experiments on Reddit, which prompted me to start this endeavor. I found his notes helpful, though the process was confusing at times.
AdBlocking VPN Proxy Server (Pi-hole, Wireguard, Privoxy, Unbound)
Richard Crosby's overview here is great, though missing some of the details. He's also adding a VPN proxy server, which I decided to skip.
Set up Pi-hole as truly self-contained DNS resolver
Anudeep's setup of Unbound to work with Pi-Hole was extremely helpful to understand how the two work together.
Unbound: How to enable DNSSEC
NLnet Labs explains what DNSSEC is and how to enable it in Unbound.
Easy As Pi Installer
Shane Caler's "one-stop-shop" to set up WireGuard, Pi-Hole, and Unbound on a Raspberry Pi. I didn't have a chance to try this out, but it might be a nice replacement for all of this at some point (and it's also probably a good place to learn).
WireGuard Installation (Raspberry Pi 2 v1.2 and above)
Adrian Mihalko's execellent instructions on installing WireGuard on a Raspberry Pi.
Some Unofficial WireGuard Documentation
Unofficial, but hugely helpful, documentation on WireGuard.
- Include screenshots of setup processes
- Move from IPtables (deprecated) to nftables
- Add an SSL certificate for the Pi-Hole Web Interface
- Include whitelist and blacklist additions
- Get local hostnames working in Pi-Hole so we can see device names instead of local IP addresses
- Add support for guest networks (specifically for Apple routers like mine)
- Include information about WireGuard's On-Demand Activation options (and SSID inclusions/exclusions)