I2C LCD adaptor module chip PCF8574T

[iv3ynb]

Hi,
I am going to build a cw keyer and I wish to use I2C display to save pins.
I have an I2C lcd adaptor module with PCF8574T chip on it, may I use it? Should I uncomment the following line?

// #define FEATURE_LCD_ADAFRUIT_I2C // Adafruit I2C LCD display using MCP23017 at addr 0x20

I think the answer will be "no, you cannot", anyway I ask to see if there is some compatibility between chips that I am missing...

Thanks for helping hand
Matteo IV3YNB

[tulipman]

Check this out: https://groups.io/g/radioartisan/topic/68630322?p=Created,,,20,2,0,0 Sent from my iPhone XS Max (512Gb)

…

On 23 May 2022, at 12:18, iv3ynb ***@***.***> wrote:  Hi, I am going to build a cw keyer and I wish to use I2C display to save pins. I have an I2C lcd adaptor module with PCF8574T chip on it, may I use it? Should I uncomment the following line? // #define FEATURE_LCD_ADAFRUIT_I2C // Adafruit I2C LCD display using MCP23017 at addr 0x20 I think the answer will be "no, you cannot", anyway I ask to see if there is some compatibility between chips that I am missing... Thanks for helping hand Matteo IV3YNB — Reply to this email directly, view it on GitHub, or unsubscribe. You are receiving this because you are subscribed to this thread.

[iv3ynb]

Thank you so much, I think this will solve the trouble.

Matteo IV3YNB

[tulipman]

Hi Matteo! I’m glad that I could help you out. Please send me a Pm if you need any more help or advice with your keyer. Are you using an Arduino Nano in your keyer? If so, be warned that it has a limited amount of memory, and that puts a limit on the amount of options that you can enable in the source-code. For instance, I wanted to enable the display option, and when I compiled the code, I got a ‘memory overflow’ warning. It simply did NOT fit in my Nano. So I made another K3NG keyer, but now using an Arduino Mega, and my problem was solved. Recently, they released a new Arduino model: The Arduino Nano Every. The Arduino Nano Every is an evolution of the traditional Arduino Nano board, but has a much more powerful processor, ATMega4089. This will allow you to make larger programs than the Arduino Uno (it has 50% more program memory) and many more variables (RAM is 200% larger). I’s pin compatible with the ‘old’ Nano, so this could be your rescue if you use a Nano in your keyer and need more memory!! Best 73 de Robbert / PA3BKL (aka TA2IX) The dutch guy living in Istanbul

On 23 May 2022 Mon at 12:42 iv3ynb ***@***.***> wrote: Thank you so much, I think this will solve the trouble. Matteo IV3YNB — Reply to this email directly, view it on GitHub <#130 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AB6FYIRWLPFEYGLMYMKY7B3VLNHJ5ANCNFSM5WVEUOKA> . You are receiving this because you commented.Message ID: ***@***.***>

-- Best regards Robbert J. van Herksen / PA3BKL

[iv3ynb]

Thanks for the infos: I want to use an Arduino MEGA 2560 for the reasons you talked about.
I'm not so much into Arduino so far, because I use to deal with Microchip PICs in MPLABX environment using C language.

I'll surely take a look at those new Arduino boards, simply for they'll have debug option in IDE 2.0: a feature that I am really missing in the 1.0 IDE, since I come from MPLABX environment.

73 de Matteo IV3YNB,
one that would "run" on CW but... it's soooo hard ;-)

[tulipman]

Well, I hated the standard Arduino IDE from the start. I’m now using the Microsoft visual Studio Code. Or, if you are not really a MS fanboy, have a look at the ATOM editor. I also used the (not free) Sublime text editor, which is amazingl! Would be cool if you could send me a video of your working K3NG keyer when it’s up and running!! BTW: I’m using Begali paddles!! Have the Stealth Limited (nr 33), and also the Graciella (a piece if Italian art!!) I’m currently QRV using my wonderful ICOM IC-705 using a Bufdipole DeLuxe. Awsome combination!! Ciao 73 de Robbert / PA3BKL (aka TA2IX)

On 23 May 2022 Mon at 13:08 iv3ynb ***@***.***> wrote: Thanks for the infos: I want to use an Arduino MEGA 2560 for the reasons you talked about. I'm not so much into Arduino so far, because I use to deal with Microchip PICs in MPLABX environment using C language. I'll surely take a look at those new Arduino boards, simply for they'll have debug option in IDE 2.0: a feature that I am really missing in the 1.0 IDE, since I come from MPLABX environment. 73 de Matteo IV3YNB, one that would "run" on CW but... it's soooo hard ;-) — Reply to this email directly, view it on GitHub <#130 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AB6FYIVJ2RNZ4P4DQEJ74TDVLNKI3ANCNFSM5WVEUOKA> . You are receiving this because you commented.Message ID: ***@***.***>

-- Best regards Robbert J. van Herksen / PA3BKL

[iv3ynb]

Well, I hated the standard Arduino IDE from the start. I’m now using the Microsoft visual Studio Code. Or, if you are not really a MS fanboy, have a look at the ATOM editor. I also used the (not free) Sublime text editor, which is amazingl! <

Cool... I hated it too since I bought my first Arduino Uno when it came first out on the market, so I left... I just got into Arduino once more because of in my new job they use to program some boards... Do these editors you talk about, feature "line by line" debugging and/or simulation/stimulus???

Would be cool if you could send me a video of your working K3NG keyer when it’s up and running!! <

Yes of course, I only have limited time to build it... please have patience :-D

I know Begali paddles, but I admire also your "Morsetasten" ;-)

73
Matteo IV3YNB

[tulipman]

Sent from my iPhone XS Max (512Gb)

On 23 May 2022, at 13:41, iv3ynb ***@***.***> wrote:  Well, I hated the standard Arduino IDE from the start. I’m now using the Microsoft visual Studio Code. Or, if you are not really a MS fanboy, have a look at the ATOM editor. I also used the (not free) Sublime text editor, which is amazingl! < Cool... I hated it too since I bought my first Arduino Uno when it came first out on the market, so I left... I just got into Arduino once more because of in my new job they use to program some boards... Do these editors you talk about, feature "line by line" debugging and/or simulation/stimulus???

It does!! Just set breakpoints and go debugging: Check this out: https://youtu.be/6cOsxaNC06c

…

Would be cool if you could send me a video of your working K3NG keyer when it’s up and running!! < Yes of course, I only have limited time to build it... please have patience :-D I've know Begali paddles, but I admire also your "Morsetasten" ;-) 73 Matteo IV3YNB — Reply to this email directly, view it on GitHub, or unsubscribe. You are receiving this because you commented.

[tulipman]

So you checked out my website? Sent from my iPhone XS Max (512Gb)

…

On 23 May 2022, at 13:41, iv3ynb ***@***.***> wrote: I've know Begali paddles, but I admire also your "Morsetasten" ;-)

[iv3ynb]

It does!!
Just set breakpoints and go debugging: <

OK, now I understand how it is possible to write long listings for Arduino boards, without entering hundreds of "serial print" commands !!!

So you checked out my website? <

Yes ! I always search for hams websites, usually starting from QRZ : it's very interesting to see "who's who" ;-)

73
Matteo IV3YNB

[tulipman]

Hi Matteo ! Just wondered how your cw keyer project is going. Are you winning?? 73 de Robbert / PA3BKL aka TA2IX

…

On Mon, May 23, 2022 at 2:16 PM iv3ynb ***@***.***> wrote: It does!! Just set breakpoints and go debugging: < OK, now I understand how it is possible to write long listings for Arduino boards, without entering hundreds of "serial print" commands !!! So you checked out my website? < Yes ! I always search for hams websites, usually starting from QRZ : it's very interesting to see "who's who" ;-) 73 Matteo IV3YNB — Reply to this email directly, view it on GitHub <#130 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AB6FYITJQHIYPQLUUO6ELTDVLNSKHANCNFSM5WVEUOKA> . You are receiving this because you commented.Message ID: ***@***.***>

-- Best regards Robbert J. van Herksen / PA3BKL

[iv3ynb]

I am building it... I used an Arduino Mega 250 R3 connected to a 4x20 LCD via I2C and 6 buttons for command mode and macros.
I am now focusing on WPM adjustment via pot. This because I have a pot "here and now", but I planned to do it with a rotary encoder that I like most... gotta find it my various junk boxes and drawers...
A friend of mine gave me a sidesweeper key to try creating code, but it's quite slow and not reliable due to switch reed contacts: it is a 3D printed project realized for a QRS beginner course. Not good for operating as a Graciella is ;-) but it works to get dits and dats.

I wish to get WPM indications on two 7 segment led displays but I cannot recognize the variable in the code to manage and visualize on the displays... can you help me this way?

I'll take some pictures asap.

[tulipman]

Hi Matteo!! Yes, rotary encoders are absolutely needed! Don’t go for the standaard potmeter type. I’m now investigating on adding a graphic touch display. That will be such a delight to use, especially macro functions. And stay far from paddles with microswitches. Just use gold- or silverplated contacts. In 1981 I found a el-bug design in the ELEKTOR magazine. It used microswitches, and it was really un-usable. I learned a LOT from it. My first paddle was a Bencher BY-01. I loved it, and still use it. If u need idea’s or help, let me know !! 73 de Robbert / TA2/PA3BKL from Istanbul Sent from my iPhone XS Max (512Gb)

…

On 6 Jun 2022, at 14:38, iv3ynb ***@***.***> wrote:  I am building it... I used an Arduino Mega 250 R3 connected to a 4x20 LCD via I2C and 6 buttons for command mode and macros. I am now focusing on WPM adjustment via pot. This because I have a pot "here and now", but I planned to do it with a rotary encoder that I like most... gotta find it my various junk boxes and drawers... A friend of mine gave me a sidesweeper key to try creating code, but it's quite slow and not reliable due to switch reed contacts: it is a 3D printed project realized for a QRS beginner course. Not good for operating as a Graciella is ;-) but it works to get dits and dats. I wish to get WPM indications on two 7 segment led displays but I cannot recognize the variable in the code to manage and visualize on the displays... can you help me this way? I'll take some pictures asap. — Reply to this email directly, view it on GitHub, or unsubscribe. You are receiving this because you commented.

[tulipman]

WPM indication is not so hard to do. There IS a WPM variable available in the code. Did you see the fantastic K3NG keyer that was made by your compatriot IZ3ZLU ? Check this out: Using a NEXTION touch display https://youtu.be/bkGq9O5qkUQ Sent from my iPhone XS Max (512Gb)

…

On 6 Jun 2022, at 14:38, iv3ynb ***@***.***> wrote:  I am building it... I used an Arduino Mega 250 R3 connected to a 4x20 LCD via I2C and 6 buttons for command mode and macros. I am now focusing on WPM adjustment via pot. This because I have a pot "here and now", but I planned to do it with a rotary encoder that I like most... gotta find it my various junk boxes and drawers... A friend of mine gave me a sidesweeper key to try creating code, but it's quite slow and not reliable due to switch reed contacts: it is a 3D printed project realized for a QRS beginner course. Not good for operating as a Graciella is ;-) but it works to get dits and dats. I wish to get WPM indications on two 7 segment led displays but I cannot recognize the variable in the code to manage and visualize on the displays... can you help me this way? I'll take some pictures asap. — Reply to this email directly, view it on GitHub, or unsubscribe. You are receiving this because you commented.

[iv3ynb]

Hi Robbert, I am building it... I used an Arduino Mega 250 R3 connected to a 4x20 LCD via I2C and 6 buttons for command mode and macros.I am now focusing on WPM adjustment via potentiometer. This because I have a potentiometer "here and now", but I am planned to do it with a rotary encoder that I like most... gotta find it my various junk boxes and drawers... :-DDD A friend of mine gave me a sidesweeper to try creating code, but it's quite slow and not reliable: it is a 3D printed project realized for a QRS begginner course. Not good for operating as a Graciella is ;-) but it works to get dits and dats. I wish to get WPM indications on two 7 segment led displays but I cannot recognize the variable in the code to manage and visualize on the displays... can you help me this way? I'll take some pictures for you, asap.73, Matteo Matteo Copetti -- IV3YNB -- JN65urhttp://iv3ynb.altervista.org Il domenica 5 giugno 2022, 14:08:17 CEST, Robbert van Herksen ***@***.***> ha scritto: Hi Matteo ! Just wondered how your cw keyer project is going. Are you winning?? 73 de Robbert / PA3BKL aka TA2IX

…

On Mon, May 23, 2022 at 2:16 PM iv3ynb ***@***.***> wrote: It does!! Just set breakpoints and go debugging: < OK, now I understand how it is possible to write long listings for Arduino boards, without entering hundreds of "serial print" commands !!! So you checked out my website? < Yes ! I always search for hams websites, usually starting from QRZ : it's very interesting to see "who's who" ;-) 73 Matteo IV3YNB — Reply to this email directly, view it on GitHub <#130 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AB6FYITJQHIYPQLUUO6ELTDVLNSKHANCNFSM5WVEUOKA> . You are receiving this because you commented.Message ID: ***@***.***>

-- Best regards Robbert J. van Herksen / PA3BKL — Reply to this email directly, view it on GitHub, or unsubscribe. You are receiving this because you authored the thread.Message ID: ***@***.***>