You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
i wish my printer is shutting down, after printing - and then after an idle from 15 minutes.
But the printer e.g. the PSU wont shut down. In the logfiles repeat:
2017-05-11 03:55:00,486 - octoprint.plugins.psucontrol - INFO - Waiting for heaters(tool0) before shutting off PSU...
2017-05-11 03:55:05,498 - octoprint.plugins.psucontrol - INFO - Waiting for heaters(tool0) before shutting off PSU...
2017-05-11 03:55:10,509 - octoprint.plugins.psucontrol - INFO - Waiting for heaters(tool0) before shutting off PSU...
2017-05-11 03:55:15,522 - octoprint.plugins.psucontrol - INFO - Waiting for heaters(tool0) before shutting off PSU...
2017-05-11 03:55:20,533 - octoprint.plugins.psucontrol - INFO - Waiting for heaters(tool0) before shutting off PSU...
2017-05-11 03:55:25,544 - octoprint.plugins.psucontrol - INFO - Waiting for heaters(tool0) before shutting off PSU...
2017-05-11 03:55:30,555 - octoprint.plugins.psucontrol - INFO - Waiting for heaters(tool0) before shutting off PSU...
But it was 3 hours after printing. So, the heaters arent hot anymore.
Can i disabled waiting for heaters? Or can i setup an force-shutdown after x minutes?
Thanks in advance.
PS: I use the ANET A8 with 2 Port Relai on Raspberry. My Setup from PSU Control is:
GPIO Mode BCM
GPIO Pin for switching (pin 17)
No Sensing
No Power on
Power off is checked, after 15 minutes and 70°
Disconnect on power off is checked.
The text was updated successfully, but these errors were encountered:
Dear PSUControl-Team,
i wish my printer is shutting down, after printing - and then after an idle from 15 minutes.
But the printer e.g. the PSU wont shut down. In the logfiles repeat:
2017-05-11 03:55:00,486 - octoprint.plugins.psucontrol - INFO - Waiting for heaters(tool0) before shutting off PSU...
2017-05-11 03:55:05,498 - octoprint.plugins.psucontrol - INFO - Waiting for heaters(tool0) before shutting off PSU...
2017-05-11 03:55:10,509 - octoprint.plugins.psucontrol - INFO - Waiting for heaters(tool0) before shutting off PSU...
2017-05-11 03:55:15,522 - octoprint.plugins.psucontrol - INFO - Waiting for heaters(tool0) before shutting off PSU...
2017-05-11 03:55:20,533 - octoprint.plugins.psucontrol - INFO - Waiting for heaters(tool0) before shutting off PSU...
2017-05-11 03:55:25,544 - octoprint.plugins.psucontrol - INFO - Waiting for heaters(tool0) before shutting off PSU...
2017-05-11 03:55:30,555 - octoprint.plugins.psucontrol - INFO - Waiting for heaters(tool0) before shutting off PSU...
But it was 3 hours after printing. So, the heaters arent hot anymore.
Can i disabled waiting for heaters? Or can i setup an force-shutdown after x minutes?
Thanks in advance.
PS: I use the ANET A8 with 2 Port Relai on Raspberry. My Setup from PSU Control is:
GPIO Mode BCM
GPIO Pin for switching (pin 17)
No Sensing
No Power on
Power off is checked, after 15 minutes and 70°
Disconnect on power off is checked.
The text was updated successfully, but these errors were encountered: