Skip to content

kfaseela/kuryr-kubernetes

 
 

Repository files navigation

Team and repository tags

kuryr-kubernetes

Kubernetes integration with OpenStack networking

The OpenStack Kuryr project enables native Neutron-based networking in Kubernetes. With Kuryr-Kubernetes it's now possible to choose to run both OpenStack VMs and Kubernetes Pods on the same Neutron network if your workloads require it or to use different segments and, for example, route between them.

Configuring Kuryr

Generate sample config, etc/kuryr.conf.sample, running the following:

$ ./tools/generate_config_file_samples.sh

Rename and copy config file at required path:

$ cp etc/kuryr.conf.sample /etc/kuryr/kuryr.conf

Edit Neutron section in /etc/kuryr/kuryr.conf, replace ADMIN_PASSWORD:

[neutron]
auth_url = http://127.0.0.1:35357/v3/
username = admin
user_domain_name = Default
password = ADMIN_PASSWORD
project_name = service
project_domain_name = Default
auth_type = password

In the same file uncomment the bindir parameter with the path to the Kuryr vif binding executables. For example, if you installed it on Debian or Ubuntu:

[DEFAULT]
bindir = /usr/local/libexec/kuryr

How to try out nested-pods locally (VLAN + trunk)

Following are the instructions for an all-in-one setup where K8s will also be running inside the same Nova VM in which Kuryr-controller and Kuryr-cni will be running. 4GB memory and 2 vCPUs, is the minimum resource requirement for the VM:

  1. To install OpenStack services run devstack with devstack/local.conf.pod-in-vm.undercloud.sample. Ensure that "trunk" service plugin is enabled in /etc/neutron/neutron.conf:

    [DEFAULT]
    service_plugins = neutron.services.l3_router.l3_router_plugin.L3RouterPlugin,neutron.services.trunk.plugin.TrunkPlugin
    
  2. Launch a VM with Neutron trunk port.

  3. Inside VM, install and setup Kubernetes along with Kuryr using devstack:
    • Since undercloud Neutron will be used by pods, Neutron services should be disabled in localrc.
    • Run devstack with devstack/local.conf.pod-in-vm.overcloud.sample. With this config devstack will not configure Neutron resources for the local cloud. These variables have to be added manually to /etc/kuryr/kuryr.conf.
  4. Once devstack is done and all services are up inside VM:
    • Configure /etc/kuryr/kuryr.conf to set UUID of Neutron resources from undercloud Neutron:

      [neutron_defaults]
      ovs_bridge = br-int
      pod_security_groups = <UNDERCLOUD_DEFAULT_SG_UUID>
      pod_subnet = <UNDERCLOUD_SUBNET_FOR_PODS_UUID>
      project = <UNDERCLOUD_DEFAULT_PROJECT_UUID>
      service_subnet = <UNDERCLOUD_SUBNET_FOR_SERVICES_UUID>
      
    • Configure worker VMs subnet:

      [pod_vif_nested]
      worker_nodes_subnet = <UNDERCLOUD_SUBNET_WORKER_NODES_UUID>
      
    • Configure “pod_vif_driver” as “nested-vlan”:

      [kubernetes]
      pod_vif_driver = nested-vlan
      
    • Configure binding section:

      [binding]
      driver = kuryr.lib.binding.drivers.vlan
      link_iface = <VM interface name eg. eth0>
      
    • Restart kuryr-k8s-controller:

      sudo systemctl restart devstack@kuryr-kubernetes.service
      

Now launch pods using kubectl, Undercloud Neutron will serve the networking.

How to try out nested-pods locally (MACVLAN)

Following are the instructions for an all-in-one setup, as above, but using the nested MACVLAN driver rather than VLAN and trunk ports.

  1. To install OpenStack services run devstack with devstack/local.conf.pod-in-vm.undercloud.sample.

  2. Launch a Nova VM with MACVLAN support

  3. Log into the VM and set up Kubernetes along with Kuryr using devstack:
    • Since undercloud Neutron will be used by pods, Neutron services should be disabled in localrc.
    • Run devstack with devstack/local.conf.pod-in-vm.overcloud.sample. With this config devstack will not configure Neutron resources for the local cloud. These variables have to be added manually to /etc/kuryr/kuryr.conf.
  4. Once devstack is done and all services are up inside VM:
    • Configure /etc/kuryr/kuryr.conf with the following content, replacing the values with correct UUIDs of Neutron resources from the undercloud:

      [neutron_defaults]
      pod_security_groups = <UNDERCLOUD_DEFAULT_SG_UUID>
      pod_subnet = <UNDERCLOUD_SUBNET_FOR_PODS_UUID>
      project = <UNDERCLOUD_DEFAULT_PROJECT_UUID>
      service_subnet = <UNDERCLOUD_SUBNET_FOR_SERVICES_UUID>
      
    • Configure worker VMs subnet:

      [pod_vif_nested]
      worker_nodes_subnet = <UNDERCLOUD_SUBNET_WORKER_NODES_UUID>
      
    • Configure “pod_vif_driver” as “nested-macvlan”:

      [kubernetes]
      pod_vif_driver = nested-macvlan
      
    • Configure binding section:

      [binding]
      link_iface = <VM interface name eg. eth0>
      
    • Restart kuryr-k8s-controller:

      sudo systemctl restart devstack@kuryr-kubernetes.service
      

Now launch pods using kubectl, Undercloud Neutron will serve the networking.

How to watch K8S api-server over HTTPS

Add absolute path of client side cert file and key file for K8S server in kuryr.conf:

[kubernetes]
api_root = https://your_server_address:server_ssl_port
ssl_client_crt_file = <absolute file path eg. /etc/kubernetes/admin.crt>
ssl_client_key_file = <absolute file path eg. /etc/kubernetes/admin.key>

If server ssl certification verification is also to be enabled, add absolute path to the ca cert:

[kubernetes]
ssl_ca_crt_file = <absolute file path eg. /etc/kubernetes/ca.crt>
ssl_verify_server_crt = True

If want to query HTTPS K8S api server with "--insecure" mode:

[kubernetes]
ssl_verify_server_crt = False

Features

  • TODO

Contribution guidelines

For the process of new feature addition, refer to the Kuryr Policy

About

Kubernetes integration with OpenStack networking

Resources

License

Stars

Watchers

Forks

Packages

No packages published

Languages

  • Python 92.1%
  • Shell 7.0%
  • Other 0.9%