R60_62.s

# Copyright:	Public domain.
# Filename:	R60_62.agc
# Purpose:	Part of the source code for Colossus 2A, AKA Comanche 055.
#		It is part of the source code for the Command Module's (CM)
#		Apollo Guidance Computer (AGC), for Apollo 11.
# Assembler:	yaYUL
# Contact:	Ron Burkey <info@sandroid.org>.
# Website:	www.ibiblio.org/apollo.
# Pages:	390-398
# Mod history:	2009-05-09 RSB	Adapted from the Colossus249/ file 
#				of the same name, using Comanche055 page 
#				images. 
#
# This source code has been transcribed or otherwise adapted from digitized
# images of a hardcopy from the MIT Museum.  The digitization was performed
# by Paul Fjeld, and arranged for by Deborah Douglas of the Museum.  Many
# thanks to both.  The images (with suitable reduction in storage size and
# consequent reduction in image quality as well) are available online at
# www.ibiblio.org/apollo.  If for some reason you find that the images are
# illegible, contact me at info@sandroid.org about getting access to the 
# (much) higher-quality images which Paul actually created.
#
# Notations on the hardcopy document read, in part:
#
#	Assemble revision 055 of AGC program Comanche by NASA
#	2021113-051.  10:28 APR. 1, 1969  
#
#	This AGC program shall also be referred to as
#			Colossus 2A

# Page 390
		BANK	34
		SETLOC	MANUVER
		BANK
		
		EBANK=	TEMPR60
		
		COUNT	27/R60
		
# CONFORMS TO GSOP CHAPTER FOUR REVISION LOGIC 09	JAN 18, 1968

R60CSM		TC	MAKECADR
		TS	TEMPR60

# INSERT PRIODSP CHECK WITH R22 (V06N49) WITH JENNINGS BRODEUR		
		
REDOMANN	CAF	BIT6
		MASK	FLAGWRD5	# IS 3-AXIS FLAG SET
		CCS	A
		TCF	TOBALL		# YES
		TC	INTPRET
		CALL
			VECPOINT	# TO COMPUTE FINAL ANGLES
		STORE	CPHI		# STORE FINAL ANGLES -- CPHI, CTHETA, CPSI
		EXIT
		
TOBALL		CAF	V06N18
		TC	BANKCALL
		CADR	GOPERF2R	# DISPLAY PLEASE PERFORM AUTO MANEUVER
		TC	R61TEST
		TC	REDOMANC	# PROCEED
		TCF	ENDMANU1	# ENTER I.E., FINISHED WITH R60
		
		TC	CHKLINUS	# TO CHECK FOR PRIORITY DISPLAYS
		TC	ENDOFJOB
		
REDOMANC	CAF	BIT6
		MASK	FLAGWRD5	# IS 3-AXIS FLAG SET
		CCS	A
		TCF	TOBALLC		# YES
		TC	INTPRET
		CALL
			VECPOINT	# TO COMPUTE FINAL ANGLES
		STORE	CPHI		# STORE ANGLES
		EXIT
		
TOBALLC		CAF	PRIO30		# IS MODE AUTO AND CTL GNC
# Page 391
		EXTEND
		RXOR	CHAN31
		MASK	13,14,15
		EXTEND
		BZF	+2		# AUTO, NON-FLASH N18
		TCF	TOBALL		# NOT AUTO
		
		CAF	V06N18		# STATIC UP NON-FLASHING V06 N18
		TC	BANKCALL
		CADR	GODSPR
		TC	CHKLINUS
		
STARTMNV	TC	BANKCALL
		CADR	GOMANUR
ENDMANUV	TCF	TOBALL		# FINISHED MANEUVER.

ENDMANU1	TC	DOWNFLAG	# RESET 3-AXIS FLAG
		ADRES	3AXISFLG	# BIT 6 FLAG 5
		CAE	TEMPR60
		TC	BANKJUMP
		
CHKLINUS	CS	FLAGWRD4
		MASK	BIT12		# IS PRIORITY DISPLAY FLAG SET?
		CCS	A
		TC	Q		# NO -- EXIT
		CA	Q
		TS	MPAC +2		# SAVE RETURN
		CS	THREE		# OBTAIN LOCATION FOR RESTART
		AD	BUF2		# HOLD Q OF LAST DISPLAY
		TS	TBASE1
		
		TC	PHASCHNG
		OCT	71		# 1.7SPOT FOR RELINUS
		
		CAF	BIT7
		TC	LINUS		# GO SET BITS FOR PRIORITY DISPLAY
		TC	MPAC +2
		
RELINUS		CAF	BIT5		# IS TRACK FLAG ON
		MASK	FLAGWRD1
		EXTEND
		BZF	GOREDO20	# NO
		
		TC	UPFLAG
		ADRES	PDSPFLAG	# R60 PRIODSP FLAG
		
		TC	UPFLAG
		ADRES	TARG1FLG	# FOR R52
		
		CAF	ZERO		# RESET TO ZERO, SINCE
# Page 392
		TS	OPTIND		# OPTIND WAS SET TO -1 BY V379
		
		CAF	PRIO14		# RESTORE ORIGINAL PRIORITY
		TC	PRIOCHNG
		
		TC	TBASE1
		
GOREDO20	TC	PHASCHNG
		OCT	111		# 1.11 FOR PIKUP20
		
		TC 	ENDOFJOB
		
R61TEST		CA	MODREG		# ARE WE IN P00.  IF YES THIS MUST BE
		EXTEND			#	VERB49 OR VERB89 SO DO ENDEXT.
		BZF	ENDMANU1	# RESET 3-AXIS & RETURN.  USER DOES ENDEXT
		CA	FLAGWRD4	# ARE WE IN R61 (P20)
		MASK	BIT12
		EXTEND
		BZF	GOTOP00H	# NO
		TC	GOTOV56		# YES
				
BIT14+7		OCT	20100
V06N18		VN	0618

# Page 393
# PROGRAM DESCRIPTION -- VECPOINT
#
# THIS INTERPRETIVE SUBROUTINE MAY BE USED TO POINT A SPACECRAFT AXIS IN A DESIRED DIRECTION.  THE AXIS
# TO BE POINTED MUST APPEAR AS A HALF UNIT DOUBLE PRECISION VECTOR IN SUCCESSIVE LOCATIONS OF ERASABLE MEMORY
# BEGINNING WITH THE LOCATION CALLED SCAXIS.  THE COMPONENTS OF THIS VECTOR ARE GIVEN IN SPACECRAFT COORDINATES.
# THE DIRECTION IN WHICH THIS AXIS IS TO BE POINTED MUST APPEAR AS A HALF UNIT DOUBLE PRECISION VECTOR IN
# SUCCESSIVE LOCATIONS OF ERASABLE MEMORY BEGINNING WITH THE ADDRESS CALLED POINTVSM.  THE COMPONENTS OF THIS
# VECTOR ARE GIVEN IN STABLE MEMBER COORDINATES.  WITH THIS INFORMTION VECPOINT COMPUTES A SET OF THREE GIMBAL
# ANGLES (2'S COMPLEMENT) CORRESPONDING TO THE CROSS-PRODUCT ROTATION BETWEEN SCAXIS AND POINTVSM AND STORES THEM
# IN T(MPAC) BEFORE RETURNING TO THE CALLER.
#
# THIS ROTATION, HOWEVER, MAY BRING THE S/C INTO GIMBAL LOCK.  WHEN POINTING A VECTOR IN THE Y-Z PLANE,
# THE TRANSPONDER AXIS, OR THE AOT FOR THE LEM, THE PROGRAM WILL CORRECT THIS PROGLEM BY ROTATING THE CROSS-
# PRODUCT ATTITUDE ABOUT POINTVSM BY A FIXED AMOUNT SUFFICIENT TO ROTATE THE DESIRED S/C ATTITUDE OUT OF GIMBAL
# LOCK.  IF THE AXIS TO BE POINTED IS MORE THAN 40.6 DEGREES BUT LESS THAN 60.5 DEG FROM THE +X (OR -X) AXIS,
# THE ADDITIONAL ROTATION TO AVOID GIMBAL LOCK IS 35 DEGREES.  IF THE AXIS IS MORE THAN 60.5 DEGREES FROM +X (OR -X)
# THE ADDITIONAL ROTATION IS 35 DEGREES.  THE GIMBAL ANGLES CORRESPONDING TO THIS ATTITUDE ARE THEN COMPUTED AND
# STORED AS 2'S COMPLEMENT ANGLES N T(MPAC) BEFORE RETURNING TO THE CALLER.
#
# WHEN POINTING THE X-AXIS, OR THE THRUST VECTOR, OR ANY VECTOR WITHIN 40.6 DEG OF THE X-AXIS, VECPOINT
# CANNOT CORRECT FOR A CROSS-PRODUCT ROTATION INTO GIMBAL LOCK.  IN THIS CASE A PLATFORM REALIGNMENT WOULD BE
# REQUIRED TO POINT THE VECTOR IN THE DESIRED DIRECTION.  AT PRESENT NO INDICATION IS GIVEN FOR THIS SITUATION
# EXCEPT THAT THE FINAL MIDDLE GIMBAL ANGLE IN MPAC +2 IS GREATER THAN 59 DEGREES.
#
# CALLING SEQUENCE
#
#	1)	LOAD SCAXIS, POINTVSM
#	2)	CALL
#			VECPOINT
#
# RETURNS WITH
#
#	1)	DESIRED OUTER GIMBAL ANGLE IN MPAC
#	2)	DESIRED INNER GIMBAL ANGLE IN MPAC +1
#	3)	DESIRED MIDDLE GIMBAL ANGLE IN MPAC +2
#
# ERASABLES USED --
#
#	1)	SCAXIS		6
#	2)	POINTVSM	6
#	3)	MIS		18
#	4)	DEL		18
#	5)	COF		6
#	6)	VECQTEMP	1
#	7)	ALL OF VAC AREA	43
#
#			TOTAL	99

		SETLOC	VECPT
		BANK
# Page 394
		EBANK=	BCDU
		
		COUNT	27/VECPT
		
VECPOINT	STQ	BOV		# SAVE RETURN ADDRESS
			VECQTEMP
			VECLEAR		# AND CLEAR OVFIND
VECLEAR		AXC,2	RTB
			MIS		# READ THE PRESENT CDU ANGLES AND
			READCDUK	# STORE THEM IN PD25, 26, 27
		STCALL	25D
			CDUTODCM	# S/C AXES TO STABLE MEMBER AXES (MIS)
		VLOAD	VXM
			POINTVSM	# RESOLVE THE POINTING DIRECTION VF INTO
			MIS		# INITIAL S/C AXES (VF = POINTVSM)
		UNIT
		STORE	28D
					# PD 28 29 30 31 32 33
		VXV	UNIT		# TAKE THE CROSS PRODUCT VF X VI
			SCAXIS		# WHERE VI = SCAXIS
		BOV	VCOMP
			PICKAXIS
		STODL	COF		# CHECK MAGNITUDE
			36D		# OF CROSS PRODUCT
		DSU	BMN		# VECTOR, IF LESS
			DPB-14		# THAN B-14 ASSUME
			PICKAXIS	# UNIT OPERATION
		VLOAD	DOT		# INVALID.
			SCAXIS
			28D
		SL1	ARCCOS
COMPMATX	CALL			# NO COMPUTE THE TRANSFORMATION FROM
			DELCOMP		# FINAL S/C AXES TO INITIAL S/C AXES MFI
		AXC,1	AXC,2
			MIS		# COMPUTE THE TRANSFORMATION FROM FINAL
			DEL		# S/C AXES TO STABLE MEMBER AXES
		CALL			# MFS = MIS MFI
			MXM3		# (IN PD LIST)
			
		DLOAD	ABS
			6		# MFS6 = SIN(CPSI)			$2
		DSU	BMN
			SINGIMLC	# = SIN(59 DEGS)			$2
			FINDGIMB	# /CPSI/ LESS THAN 59 DEGS.
					# I.E., DESIRED ATTITUDE NOT IN GIMBAL LOCK
					
		DLOAD	ABS		# CHECK TO SEE IF WE ARE POINTING
			SCAXIS		# THE THRUST AXIS
		DSU	BPL
			SINVEC1		# SIN 49.4 DEGS				$2
# Page 395
			FINDGIMB	# IF SO, WE ARE TRYING TO POINT IT INTO
		VLOAD			# GIMBAL LOCK, ABORT COULD GO HERE
		STADR
		STOVL	MIS +12D
		STADR			# STORE MFS (IN PD LIST) IN MIS
		STOVL	MIS +6
		STADR
		STOVL	MIS
			MIS +6		# INNER GIMBAL AXIS IN FINAL S/C AXES
		BPL	VCOMP		# LOCATE THE IG AXIS DIRECTION CLOSEST TO
			IGSAMEX		# FINAL X S/C AXIS
			
IGSAMEX		VXV	BMN		# FIND THE SHORTEST WAY OF ROTATING THE 
			SCAXIS		# S/C OUT OF GIMBAL LOCK BY A ROTATION 
			U=SCAXIS	# ABOUT +- SCAXIS, I.E., IF  (IG (SGN MFS3)
					# X SCAXIS . XF) LESS THAN Q, U = SCAXIS
					# OTHERWISE U = -SCAXIS.
					
		VLOAD	VCOMP
			SCAXIS
		STCALL	COF		# ROTATE ABOUT -SCAXIS
			CHEKAXIS
U=SCAXIS	VLOAD
			SCAXIS
		STORE	COF		# ROTATE ABOUT + SCAXIS
CHEKAXIS	DLOAD	ABS
			SCAXIS		# SEE IF WE ARE POINTING THE AOT
		DSU	BPL
			SINVEC2		# SIN 29.5 DEGS				$2
			PICKANG1	# IF SO, ROTATE 50 DEGS ABOUT +- SCAXIS
		DLOAD	GOTO		# IF NOT, MUST BE POINTING THE TRANSPONDER
			VECANG2		# OR SOME VECTOR IN THE Y, OR Z PLANE
			COMPMFSN	# IN THIS CASE ROTATE 35 DEGS TO GET OUT
					# OF GIMBAL LOCK (VECANG2 $360)
PICKANG1	DLOAD
			VECANG1		# = 50 DEGS.			      $360
COMPMFSN	CALL
			DELCOMP		# COMPUTE THE ROTATION ABOUT SCAXIS TO
		AXC,1	AXC,2		# BRING MFS OUT OF GIMBAL LOCK
			MIS
			DEL
		CALL			# COMPUTE THE NEW TRANSFORMATION FROM
			MXM3		# DESIRED S/C AXES TO STABLE MEMBER AXES
					# WHICH WILL ALIGN VI WITH VF AND AVOID
					# GIMBAL LOCK
FINDGIMB	AXC,1	CALL
			0		# EXTRACT THE COMMANDED CDU ANGLES FROM
			DCMTOCDU	# THIS MATRIX
		RTB	SETPD
			V1STO2S		# CONVERT TO 2'S COMPLEMENT
# Page 396
			0
		GOTO
			VECQTEMP	# RETURN TO CALLER
			
PICKAXIS	VLOAD	DOT		# IF VF X VI = 0, FIND VF, VI
			28D
			SCAXIS
		BMN	TLOAD
			ROT180
			25D
		GOTO			# IF VF = VI, CDU DESIRED = PRESENT CDU
			VECQTEMP	# PRESENT CDU ANGLES
			
ROT180		VLOAD	VXV		# IF VF, VI ANTI-PARALLEL, 180 DEG ROTATION
			MIS +6		# IS REQUIRED.  Y STABLE MEMBER AXIS IN
			HIUNITX		# INITIAL S/C AXES.
		UNIT	VXV		# FIND Y(SM) X X(I)
			SCAXIS		# FIND UNIT(VI X UNIT(Y(SM) X X(I)))
		UNIT	BOV		# I.E., PICK A VECTOR IN THE PLANE OF X(I),
			PICKX		# Y(SM) PERPENDICULAR TO VI
		STODL	COF
			36D		# CHECK MAGNITUDE
		DSU	BMN		# OF THIS VECTOR.
			DPB-14		# IF LESS THAN B-14,
			PICKX		# PICK X-AXIS.
		VLOAD
			COF
XROT		STODL	COF
			HIDPHALF
		GOTO
			COMPMATX
PICKX		VLOAD	GOTO		# PICK THE XAXIS IN THIS CASE
			HIUNITX
			XROT
		BANK	35
		SETLOC	MANUVER1
		BANK
		
SINGIMLC	2DEC	.4285836003	# = SIN(59)				$2

SINVEC1		2DEC	.3796356537	# = SIN(49.4)				$2

SINVEC2		2DEC	.2462117800	# = SIN(29.5)				$2

VECANG1		2DEC	.1388888889	# = 50 DEGREES			      $360

VECANG2		2DEC	.09722222222	# = 35 DEGREES			      $360


1BITDP		OCT	0		# KEEP THIS BEFORE DPB(-14)	  ********
DPB-14		OCT	00001
# Page 397
		OCT	00000
		BANK	34
		SETLOC	MANUVER
		BANK
		
# Page 398
# ROUTINE FOR INITIATING AUTOMATIC MANEUVER VIA KEYBOARD (V49)

		EBANK=	CPHI
		
		COUNT	27/R62
				
R62DISP		CAF	V06N22		# DISPLAY COMMAND ICDUS CPHI, CTHETA, CPHI
		TC	BANKCALL
		CADR	GOFLASH
		TCF	ENDEXT	
		TCF	GOMOVE		# PROCEED
		TCF	R62DISP		# ENTER
		
					# ASTRONAUT MAY LOAD NEW ICDUS AT THIS
					# POINT.
GOMOVE		TC	UPFLAG		# SET FOR 3-AXIS MANEUVER
		ADRES	3AXISFLG
		
		TC	BANKCALL
		CADR	R60CSM
		TCF	ENDEXT