Skip to content

Releases: milkv-duo/duo-buildroot-sdk

Duo-V1.1.0

10 Apr 14:00
@carbonfix carbonfix
Duo-V1.1.0
c3843a9
Compare
Choose a tag to compare
Duo-V1.1.0 Latest
Latest

Change log V1.1.0

  • Supports DuoS eMMC version for USB burning. Installation guide here.
  • Added wget,curl commands.
  • Supports epoll for kernel.

Known Issues

  • Duo 256M and DuoS does not yet support wiringX and pinpong library.
  • DuoS does not yet support arduino.
  • Duo arduino firmware does not support camera at the moment.

The firmware introduction:

  • Enable ssh
  • Enable RNDIS
  • Blink LED
  • Root password: milkv

Login via RNDIS using ssh:

ssh root@192.168.42.1

If you want to disable LED blinking:

mv /mnt/system/blink.sh /mnt/system/blink.sh_backup && sync

then reboot the board.

Using the IO-Board for Duo or Duo256M

https://milkv.io/docs/duo/io-board/usb-ethernet-iob

Assets 8

Duo-V1.0.9

27 Feb 10:08
@carbonfix carbonfix
Duo-V1.0.9
c737560
Compare
Choose a tag to compare
Duo-V1.0.9

Change log V1.0.9

  • The camera test of Duo supports face detection, more information here.
  • Added some commands, such as lsblk, stress-ng, fio, etc.
  • Duo and Duo256M support arduino. more information here.

Known Issues

  • Duo 256M and DuoS does not yet support wiringX and pinpong library.
  • DuoS does not yet support arduino.
  • Duo arduino firmware does not support camera at the moment.

The firmware introduction:

  • Enable ssh
  • Enable RNDIS
  • Blink LED
  • Root password: milkv

Login via RNDIS using ssh:

ssh root@192.168.42.1

If you want to disable LED blinking:

mv /mnt/system/blink.sh /mnt/system/blink.sh_backup && sync

then reboot the board.

Using the IO-Board for Duo or Duo256M

Note that when using the IO-Board, the USB network (RNDIS) is not available, Please use the Ethernet interface on the IO-Board.

If you need to assign a fixed MAC address to the Ethernet port of the IO-Board, please execute the following command(Replace the MAC address in the command with the MAC address you want to set, and please note that MAC addresses of different devices within the same network segment must not be duplicated).

echo "pre-up ifconfig eth0 hw ether 78:01:B3:FC:E8:55" >> /etc/network/interfaces && sync

then reboot the board.

Enable the 4 USB ports on the IO-Board:

ln -sf /mnt/system/usb-host.sh /mnt/system/usb.sh
sync

then reboot the board.

Restore the USB network (RNDIS) when the IO-Board is not used:

ln -sf /mnt/system/usb-rndis.sh /mnt/system/usb.sh
sync

then reboot the board.

Assets 8

Duo-V1.0.8

30 Jan 14:59
@carbonfix carbonfix
Duo-V1.0.8
326b188
Compare
Choose a tag to compare
Duo-V1.0.8

Change log V1.0.8

  • Support Duo S.
  • The camera test of Duo256M and DuoS supports face detection, more information here.

Known Issues

  • DuoS does not yet support wiringX and pinpong library.

The firmware introduction:

  • Enable ssh
  • Enable RNDIS
  • Blink LED
  • Root password: milkv

Login via RNDIS using ssh:

ssh root@192.168.42.1

If you want to disable LED blinking:

mv /mnt/system/blink.sh /mnt/system/blink.sh_backup && sync

then reboot the board.

Using the IO-Board for Duo or Duo256M

Note that when using the IO-Board, the USB network (RNDIS) is not available, Please use the Ethernet interface on the IO-Board.

If you need to assign a fixed MAC address to the Ethernet port of the IO-Board, please execute the following command(Replace the MAC address in the command with the MAC address you want to set, and please note that MAC addresses of different devices within the same network segment must not be duplicated).

echo "pre-up ifconfig eth0 hw ether 78:01:B3:FC:E8:55" >> /etc/network/interfaces && sync

then reboot the board.

Enable the 4 USB ports on the IO-Board:

ln -sf /mnt/system/usb-host.sh /mnt/system/usb.sh
sync

then reboot the board.

Restore the USB network (RNDIS) when the IO-Board is not used:

ln -sf /mnt/system/usb-rndis.sh /mnt/system/usb.sh
sync

then reboot the board.

Assets 6

Duo-V1.0.7

23 Dec 09:28
@carbonfix carbonfix
Duo-V1.0.7
1ef1e15
Compare
Choose a tag to compare
Duo-V1.0.7

Change log V1.0.7

  • Support Duo 256M.
  • Duo/Duo256M option added to compile script, see the README or official documentation.
  • Integrated camera rtsp push streaming test program, more information here.

Known Issues

  • Duo 256M does not yet support wiringX and pinpong library.

The firmware introduction:

  • Enable ssh
  • Enable RNDIS
  • Blink LED
  • Root password: milkv

Login via RNDIS using ssh:

ssh root@192.168.42.1

If you want to disable LED blinking:

mv /mnt/system/blink.sh /mnt/system/blink.sh_backup && sync

then reboot the board.

Use the IO-Board

Note that when using the IO-Board, the USB network (RNDIS) is not available, Please use the Ethernet interface on the IO-Board.

If you need to assign a fixed MAC address to the Ethernet port of the IO-Board, please execute the following command(Replace the MAC address in the command with the MAC address you want to set, and please note that MAC addresses of different devices within the same network segment must not be duplicated).

echo "pre-up ifconfig eth0 hw ether 78:01:B3:FC:E8:55" >> /etc/network/interfaces && sync

then reboot the board.

Enable the 4 USB ports on the IO-Board:

rm /mnt/system/usb.sh
ln -s /mnt/system/usb-host.sh /mnt/system/usb.sh
sync

then reboot the board.

Restore the USB network (RNDIS) when the IO-Board is not used:

rm /mnt/system/usb.sh
ln -s /mnt/system/usb-rndis.sh /mnt/system/usb.sh
sync

then reboot the board.

Assets 6

Duo-V1.0.6

01 Dec 03:32
@carbonfix carbonfix
Duo-V1.0.6
9426e0a
Compare
Choose a tag to compare
Duo-V1.0.6

Change log V1.0.6

  • README: Add instructions for using Docker to compile images.
  • Support mailbox communication between big core and small core, see here for details.

The firmware introduction:

  • Enable ssh
  • Enable RNDIS
  • Blink LED
  • Root password: milkv

Login via RNDIS using ssh:

ssh root@192.168.42.1

If you want to disable LED blinking:

mv /mnt/system/blink.sh /mnt/system/blink.sh_backup && sync

then reboot the board.

Use the IO-Board

Note that when using the IO-Board, the USB network (RNDIS) is not available, Please use the Ethernet interface on the IO-Board.

If you need to assign a fixed MAC address to the Ethernet port of the IO-Board, please execute the following command(Replace the MAC address in the command with the MAC address you want to set, and please note that MAC addresses of different devices within the same network segment must not be duplicated).

echo "pre-up ifconfig eth0 hw ether 78:01:B3:FC:E8:55" >> /etc/network/interfaces && sync

then reboot the board.

Enable the 4 USB ports on the IO-Board:

rm /mnt/system/usb.sh
ln -s /mnt/system/usb-host.sh /mnt/system/usb.sh
sync

then reboot the board.

Restore the USB network (RNDIS) when the IO-Board is not used:

rm /mnt/system/usb.sh
ln -s /mnt/system/usb-rndis.sh /mnt/system/usb.sh
sync

then reboot the board.

Assets 3

Duo-V1.0.5

19 Oct 11:56
@carbonfix carbonfix
Duo-V1.0.5
806b8d4
Compare
Choose a tag to compare
Duo-V1.0.5

Change log V1.0.5

  • Added support for IPV6.
  • Replaced cvi_pinmux command with duo-pinmux, more information here.
  • Reordered the pin numbers in wiringX and python-pinong library.
  • Released the generic freertos code for the second core (little one).

The firmware introduction:

  • Enable ssh
  • Enable RNDIS
  • Blink LED
  • Root password: milkv

Login via RNDIS using ssh:

ssh root@192.168.42.1

If you want to disable LED blinking:

mv /mnt/system/blink.sh /mnt/system/blink.sh_backup && sync

then reboot the board.

Use the IO-Board

Note that when using the IO-Board, the USB network (RNDIS) is not available, Please use the Ethernet interface on the IO-Board.

If you need to assign a fixed MAC address to the Ethernet port of the IO-Board, please execute the following command(Replace the MAC address in the command with the MAC address you want to set, and please note that MAC addresses of different devices within the same network segment must not be duplicated).

echo "pre-up ifconfig eth0 hw ether 78:01:B3:FC:E8:55" >> /etc/network/interfaces && sync

then reboot the board.

Enable the 4 USB ports on the IO-Board:

rm /mnt/system/usb.sh
ln -s /mnt/system/usb-host.sh /mnt/system/usb.sh
sync

then reboot the board.

Restore the USB network (RNDIS) when the IO-Board is not used:

rm /mnt/system/usb.sh
ln -s /mnt/system/usb-rndis.sh /mnt/system/usb.sh
sync

then reboot the board.

Assets 3

Duo-V1.0.4

08 Sep 11:54
@carbonfix carbonfix
Duo-V1.0.4
bb552e5
Compare
Choose a tag to compare
Duo-V1.0.4

Upload new image and SDK:

  • Enable ssh
  • Enable RNDIS
  • Blink LED
  • Root password: milkv

Login via RNDIS using ssh:

ssh root@192.168.42.1

If you want to disable LED blinking:

mv /mnt/system/blink.sh /mnt/system/blink.sh_backup && sync

then reboot the board

Use the IO-Board

Note that when using the IO-Board, the USB network (RNDIS) is not available, Please use the Ethernet interface on the IO-Board

If you need to assign a fixed MAC address to the Ethernet port of the IO-Board, please execute the following command(Replace the MAC address in the command with the MAC address you want to set, and please note that MAC addresses of different devices within the same network segment must not be duplicated)

echo "pre-up ifconfig eth0 hw ether 78:01:B3:FC:E8:55" >> /etc/network/interfaces && sync

then reboot the board

Enable the 4 USB ports on the IO-Board:

rm /mnt/system/usb.sh
ln -s /mnt/system/usb-host.sh /mnt/system/usb.sh
sync

then reboot the board

Restore the USB network (RNDIS) when the IO-Board is not used

rm /mnt/system/usb.sh
ln -s /mnt/system/usb-rndis.sh /mnt/system/usb.sh
sync

then reboot the board

Change log V1.0.4

  • Added support for Python and pip tools

  • Added support for pinpong library

  • wiringX supports SPI and UART functionality

  • Enable swap functionality, that means you can use SD card space as RAM
    Please execute the following two commands to activate it

    mkswap /dev/mmcblk0p3
swapon /dev/mmcblk0p3

    then run free -h command to check if the swap is active (256M)

    DISCLAIMER: This may cause wear and tear on your SD card leading to a shorter drive lifespan!
    It is strongly recommended to enable swap functionality only when there is insufficient memory available!

Assets 3

Duo-V1.0.3

17 Aug 09:46
@carbonfix carbonfix
Duo-V1.0.3
be2a695
Compare
Choose a tag to compare
Duo-V1.0.3

Upload new image and sdk:

  • Enable ssh
  • Enable RNDIS
  • Blink LED
  • Root password: milkv

Login via RNDIS using ssh:

ssh root@192.168.42.1

If you want to disable LED blinking:

mv /mnt/system/blink.sh /mnt/system/blink.sh_backup && sync

then reboot the board

Use the IO-Board

Note that when using the IO-Board, the USB network (RNDIS) is not available, Please use the Ethernet interface on the IO-Board

Enable the 4 USB ports on the IO-Board:

rm /mnt/system/usb.sh
ln -s /mnt/system/usb-host.sh /mnt/system/usb.sh
sync

then reboot the board

Restore the USB network (RNDIS) when the IO-Board is not used

rm /mnt/system/usb.sh
ln -s /mnt/system/usb-rndis.sh /mnt/system/usb.sh
sync

then reboot the board

Assets 3

20230807

07 Aug 07:51
@carbonfix carbonfix
20230807
0caef94
Compare
Choose a tag to compare
20230807

Upload new image and sdk:

  • Enable ssh
  • Enable RNDIS
  • Blink LED
  • Root password: milkv

Login via RNDIS using ssh:

ssh root@192.168.42.1

If you want to disable LED blinking:

mv /mnt/system/blink.sh /mnt/system/blink.sh_backup && sync

then reboot the board

Use the IO-Board

Note that when using the IO-Board, the USB network (RNDIS) is not available, Please use the Ethernet interface on the IO-Board

Enable the 4 USB ports on the IO-Board:

rm /mnt/system/usb.sh
ln -s /mnt/system/usb-host.sh /mnt/system/usb.sh
sync

then reboot the board

Restore the USB network (RNDIS) when the IO-Board is not used

rm /mnt/system/usb.sh
ln -s /mnt/system/usb-rndis.sh /mnt/system/usb.sh
sync

then reboot the board

Assets 3

20230616

16 Jun 14:53
@carbonfix carbonfix
20230616
0ec133c
Compare
Choose a tag to compare
20230616

Upload new image and sdk:

  • Enable ssh
  • Enable RNDIS
  • Blink LED
  • Root password: milkv

Login via RNDIS using ssh:
ssh root@192.168.42.1

If you want to disable LED blinking:
mv /mnt/system/blink.sh /mnt/system/blink.sh_backup && sync
then reboot the board

Assets 4